Volkswagen Golf / Golf Plus. Manual - part 147

 

  Index      Volkswagen     Volkswagen Golf (2004) / Golf Plus (2005) - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  145  146  147  148   ..

 

 

Volkswagen Golf / Golf Plus. Manual - part 147

 

 

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

– Recreate original joint, RP spot weld seam and SG plug weld

seam.

– Recreate remaining joint side member reinforcement, SG

stepped seam.

– Reform wheel housing flange.
– Wipe away excess adhesive and seal wheel arch.

Body Repairs - Edition 06.2010

11. Renewing side member    

169

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

RO: 51 46 55 00

12

Renewing seat cross member

mounting plate

(outer)

WARNING

Observe safety notes!

⇒ General Information; Body Repairs, General Body Repairs ;

Safety instructions

Note

If a thread in the seat cross member mounting plate is dam‐

aged, the component must be replaced.

The vehicle identification number is stamped on the right side

of the vehicle. If this member has to be replaced during acci‐

dent damage repair, an impartial expert is to be consulted

(reference chassis number) prior to the work being carried out.

Body Repairs - Edition 06.2010

170

     Rep. gr.51 - Body - centre

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

12.1

Removing

Note

When separating laser welded seams, ensure that the underlying

panels are not damaged.

– Separate original joint.
– Remove remaining material.

Body Repairs - Edition 06.2010

12. Renewing seat cross member mounting plate    

171

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

12.2

Installing

12.2.1

Preparing new part

Replacement part
♦ Seat cross member mounting plate
– Drill 7 mm ∅ holes for SG plug weld seam.
– Adapt new part to fit and fix in position.

12.2.2

Welding in

– Weld in seat cross member mounting plate, SG plug weld

seam.

Body Repairs - Edition 06.2010

172

     Rep. gr.51 - Body - centre

 

 

 

 

 

 

 

Content   ..  145  146  147  148   ..