Volkswagen Golf / Golf Plus. Manual - part 120

 

  Index      Volkswagen     Volkswagen Golf (2004) / Golf Plus (2005) - service repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  118  119  120  121   ..

 

 

Volkswagen Golf / Golf Plus. Manual - part 120

 

 

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

8.1

Contents of thread repair kit

1 - Twist drill ∅ 12.5 mm
2 - Thread-cutting tap M12 x

1.5
3 - Fitting spindle
4 - Thread insert M12 x 1.5 x

24 ( -VAS 6058/1- )
5 - Pin breaker with magnetic

end

Body Repairs - Edition 06.2010

8. Repairing threads for securing subframe (suspension subframe)    

61

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

8.2

Repairing thread

8.2.1

Drilling thread

– Drill out thread using twist drill.

Note

Use drill -VAS 6267- when drilling and shaping.

The drill must be held by an assistant using an additional hand

support when drilling.

Do not cant drill.

Body Repairs - Edition 06.2010

62

     Rep. gr.50 - Body - front

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

8.2.2

Cutting the thread

– Cut thread with thread-cutting tap
– Clean threaded sleeve (with compressed air).

8.2.3

Inserting thread insert

– Screw thread insert -3- onto fitting spindle until the fitting pin

-2- contacts the fitting lug -1- on the fitting spindle.

Body Repairs - Edition 06.2010

8. Repairing threads for securing subframe (suspension subframe)    

63

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

– Screw thread insert into the threaded plate until the top of the

thread insert is flush with the outer edge of the threaded plate

(visual check).

– Then screw the thread insert inwards a 

1

/4 turn.

Note

The thread insert must screw in easily.

– Remove fitting spindle.

– Break off drive pin of thread insert using pin breaker.
– Install subframe (suspension subframe) (torque settings) ⇒ 

Suspension, axles, steering; Rep. gr.  40 ; Removing and in‐

stalling subframe, Torque settings.

Body Repairs - Edition 06.2010

64

     Rep. gr.50 - Body - front

 

 

 

 

 

 

 

Content   ..  118  119  120  121   ..