Nissan Versa Sedan. Instruction - part 876

TM-410

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P2859 CLUTCH A PRESSURE

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle

5. Check the first trip DTC.
Is “P2859” detected?

YES

>> Go to 

TM-410, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268226

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

. 

Is the inspection result normal?

YES 

>> Replace  transaxle assembly. Refer to 

TM-452, "Removal and Installation"

.

NO

>> Repair or replace  malfunctioning parts.

Selector lever

: “D” position

Accelerator pedal position

: 0.7/8 or more

Vehicle speed

: 45 km/h (28 MPH) or more

P285A CLUTCH B PRESSURE

TM-411

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P285A CLUTCH B PRESSURE

DTC Logic

INFOID:0000000009268227

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• Be sure to perform “

TM-412, "Diagnosis Procedure"

” and then perform “DTC CONFIRMATION PRO-

CEDURE”.

• Never perform "DTC CONFIRMATION PROCEDURE" before the repairs. Doing so may result in a sec-

ondary malfunction.

• Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P285A

Clutch B pressure disengage-
ment performance

The detection conditions continuously for 200 
msec or more under the following diagnosis 
conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Vehicle speed: 10 km/h (6 MPH) or more
- Engine speed: More than 550 rpm
- Output speed: More than 300 rpm
- Secondary pulley speed: More than 300 

rpm

- Command for the 1GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V
• Detection conditions
- Acceleration/deceleration: Less than 

−0.05 

G

- Actual auxiliary gearbox gear ratio 

− Auxilia-

ry gearbox 1GR ratio 

≥ 50%

• High clutch & reverse brake solenoid 

valve

• Control valve assembly

The auxiliary gearbox gear ratio is 

±10% or 

less for the auxiliary gearbox 2GR ratio contin-
uously for 500 msec or more under the follow-
ing diagnosis conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Accelerator pedal position: 0.7/8 or more
- Engine speed: More than 550 rpm
- Secondary pulley speed: More than 300 

rpm

- Output speed: More than 300 rpm
- Command for the 1GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V

TM-412

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P285A CLUTCH B PRESSURE

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P285A” detected?

YES

>> Go to 

TM-412, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268228

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

. 

Is the inspection result normal?

YES 

>> Replace  transaxle assembly. Refer to 

TM-452, "Removal and Installation"

.

NO

>> Repair or replace  malfunctioning parts.

Selector lever

: “L” POSITION

Accelerator pedal position

: 0.7/8 or more

Vehicle speed

: 10 km/h (6 MPH) or more

MAIN POWER SUPPLY AND GROUND CIRCUIT

TM-413

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

MAIN POWER SUPPLY AND GROUND CIRCUIT

Diagnosis Procedure

INFOID:0000000009268229

1.

CHECK TCM POWER CIRCUIT (PART 1)

1. Turn  ignition switch OFF.

2. Disconnect  TCM connector.

3. Check  voltage between  TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK TCM POWER CIRCUIT  (PART 2)

Check  voltage between  TCM harness connector terminals and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

CHECK TCM GROUND CIRCUIT

Check  continuity between TCM harness connector terminals and ground.

Is the  inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace  malfunctioning parts.

4.

DETECT MALFUNCTION ITEMS (PART 1)

Check the following items:

• Open or short circuit of  harness between battery positive terminal and TCM connectors terminals 45 and 46.

• 10A fuse (No.33, fuse and fusible link block). Refer to 

PG-61, "Terminal Arrangement"

.

Is the inspection result normal?

YES 

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace  malfunctioning parts.

5.

CHECK CIRCUIT BETWEEN IPDM E/R AND TCM (PART 1)

1. Turn ignition switch OFF.

2. Disconnect  IPDM E/R connector.

TCM

Ground

Voltage

Connector

Terminal

F44

45

Ground

10 – 16 V

46

TCM

Ground

Condition

Voltage

Connector

Terminal

F44

47

Ground

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

48

Ignition switch ON

10 – 16 V

Ignition switch OFF

Approx. 0 V

TCM

Ground

Continuity

Connector

Terminal

F44

41

Ground

Existed

42