Nissan Versa Sedan. Instruction - part 875

TM-406

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P2765 CLUTCH B SPEED SENSOR

6.

CHECK CIRCUIT BETWEEN IPDM E/R AND SECONDARY SPEED SENSOR (PART 1)

1. Disconnect  IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector terminal and secondary speed sensor harness

connector terminal. 

Is the check result normal?

YES

>> GO TO 7.

NO

>> Repair or replace  malfunctioning parts.

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND SECONDARY SPEED SENSOR (PART 2)

Check continuity between IPDM E/R harness connector terminal and ground. 

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace  malfunctioning parts.

8.

DETECT MALFUNCTIONING ITEMS

Check the following items:

• Harness open circuit or short circuit between  ignition switch and IPDM E/R. Refer to 

PG-20, "Wiring Dia-

gram — Ignition Power Supply —"

.

• 10A fuse (No.49, IPDM E/R). Refer to 

PG-62, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace  malfunctioning parts.

IPDM E/R

Secondary speed sensor

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F48

3

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E45

21

Ground

Not existed

P2857 CLUTCH A PRESSURE

TM-407

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P2857 CLUTCH A PRESSURE

DTC Logic

INFOID:0000000009268221

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• Be sure to perform “

TM-407, "Diagnosis Procedure"

” and then perform “DTC CONFIRMATION PRO-

CEDURE”.

• Never perform "DTC CONFIRMATION PROCEDURE" before the repairs. Doing so may result in a sec-

ondary malfunction.

• Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P2857” detected?

YES

>> Go to 

TM-407, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268222

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

. 

Is the inspection result normal?

YES 

>> Replace  transaxle assembly. Refer to 

TM-452, "Removal and Installation"

.

NO

>> Repair or replace  malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P2857

Clutch A pressure engage-
ment performance

The auxiliary gearbox gear ratio is 2.232 or 
more for the auxiliary gearbox 1GR ratio con-
tinuously for 5 seconds or more under the fol-
lowing diagnosis conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Accelerator pedal position: 0.7/8 or more
- Engine speed: More than 550 rpm
- Output speed: More than 300 rpm
- Secondary pulley speed: More than 300 

rpm

- Command for the 1GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V

• Low brake solenoid valve
• Control valve assembly

Selector lever

: “L” POSITION

Accelerator pedal position

: 0.7/8 or more

Vehicle speed

: 10 km/h (6 MPH) or more

TM-408

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

P2858 CLUTCH B PRESSURE

P2858 CLUTCH B PRESSURE

DTC Logic

INFOID:0000000009268223

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• Be sure to perform “

TM-408, "Diagnosis Procedure"

” and then perform “DTC CONFIRMATION PRO-

CEDURE”.

• Never perform "DTC CONFIRMATION PROCEDURE" before the repairs. Doing so may result in a sec-

ondary malfunction.

• Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

2. Drive the vehicle.

3. Maintain the following conditions for 10 seconds or more.

4. Stop the vehicle.

5. Check the first trip DTC.
Is “P2858” detected?

YES

>> Go to 

TM-408, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009268224

1.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

. 

Is the inspection result normal?

YES 

>> Replace  transaxle assembly. Refer to 

TM-452, "Removal and Installation"

.

NO

>> Repair or replace  malfunctioning parts.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P2858

Clutch B pressure engage-
ment performance

The auxiliary gearbox gear ratio is 2.232 or 
more for the auxiliary gearbox 2GR ratio con-
tinuously for 5 seconds or more under the fol-
lowing diagnosis conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Accelerator pedal position: 0.7/8 or more
- Engine speed: More than 550 rpm
- Output speed: More than 300 rpm
- Secondary pulley speed: More than 300 

rpm

- Command for the 2GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V

• High clutch & reverse brake solenoid 

valve

• Control valve assembly

Selector lever

: “D” POSITION

Accelerator pedal position

: 0.7/8 or more

Vehicle speed

: 45 km/h (28 MPH) or more

P2859 CLUTCH A PRESSURE

TM-409

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P2859 CLUTCH A PRESSURE

DTC Logic

INFOID:0000000009268225

DTC DETECTION LOGIC

DTC COFIRMATION PROCEDURE

CAUTION:

• Be sure to perform "

TM-410, "Diagnosis Procedure"

" and then perform "DTC CONFIRMATION PRO-

CEDURE".

• Never perform "TC CONFIRMATION PROCEDURE" before the repairs. Doing so may result in a sec-

ondary malfunction.

• Be careful of the driving speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

1. Start the engine.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P2859

Clutch A pressuren disen-
gagement performance

The detection conditions continuously for 200 
msec or more under the following diagnosis 
conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Vehicle speed: 10 km/h (6 MPH) or more
- Engine speed: More than 550 rpm
- Output speed: More than 300 rpm
- Secondary pulley speed: More than 300 

rpm

- A lapse of 500 msec or more after the stop 

lamp switch is turned from ON to OFF.

- Command for the 2GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V
• Detection conditions
- Acceleration/deceleration: Less than 

−0.05 

G

- Actual auxiliary gearbox gear ratio 

− Auxilia-

ry gearbox 2GR ratio 

≥ 50%

• Low brake solenoid valve
• Control valve assembly

The auxiliary gearbox gear ratio is 

±10% or 

less for the auxiliary gearbox 1GR ratio contin-
uously for 500 msec or more under the follow-
ing diagnosis conditions:
• Diagnosis conditions
- Selector lever: Other than “P”, “R” and “N” 

positions

- Accelerator pedal position: 0.7/8 or more
- Engine speed: More than 550 rpm
- Secondary pulley speed: More than 300 

rpm

- Output speed: More than 300 rpm
- Command for the 2GR of auxiliary gearbox 

is in progress.

- Auxiliary gearbox shifting is not in progress. 
- TCM power supply voltage: More than 11 V