Suzuki Kizashi (2010 year). Instruction - part 19

 

  Index      Suzuki     Suzuki Kizashi (2010 year) - instruction in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     17      18      19      20     ..

 

 

Suzuki Kizashi (2010 year). Instruction - part 19

 

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Note that two or more compact spare
Snow Tires
tires should not be used on one vehi-
WARNING
Your vehicle is equipped with all-sea-
cle simultaneously.
son tires which are designed for use in
(Continued)
summer and most winter conditions.
• The compact spare tire has a
WARNING
For improved traction in severe winter
much shorter tread life than the
conditions, SUZUKI recommends
The compact spare tire and wheel
conventional tires on your vehi-
mounting radial snow tires on all four
are intended for temporary emer-
cle. Replace the tire as soon as
wheels. Snow tires must be the same
gency use only. Continuous use
the tread wear indicator
size as the standard tires. Also be sure
of this spare can result in tire fail-
appears.
to use the tires of the same type and
ure and loss of control. Always
• When replacing the compact
brand on all four wheels of your vehi-
observe these precautions when
tire, use a replacement tire with
cle.
using this spare:
the exact same size and con-
Your vehicle will handle differ-
struction.
ently with this temporary spare.
Do not exceed 80 km/h (50 mph)
CAUTION
speed.
Replace this spare with a stan-
For intelligent All Wheel Drive (i-
dard tire and wheel as soon as
AWD) models, driving with an
possible.
underinflated compact spare tire
Use of this spare will reduce
or over 80 km/h (50 mph) while
ground clearance.
using a compact spare tire can
Recommended air pressure for
result in damage to the drive
this spare is 420 kPa (60 psi).
train.
Do not use tire chains on the
compact spare. If you must use
tire chains, rearrange the
wheels so standard tires and
wheels are fitted to the front
axle.
(Continued)
7-35

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
GLOSSARY OF TIRE TERMINOL-
Maximum Inflation Pressure - the max-
Vehicle Capacity Weight - the rated
OGY
imum cold inflation pressure a tire is
cargo and luggage load plus 68 kilo-
Accessory Weight
- the combined
designed to support in normal service.
grams (150 lbs) times the vehicle’s
weight (in excess of those standard
designated seating capacity.
Maximum Loaded Vehicle Weight -
items which may be replaced) of CVT,
the sum of curb weight, accessory
Vehicle Maximum Load on the Tire -
power steering, power brakes, power
weight, vehicle capacity weight (total
the load on an individual tire that is
windows, power seats, radio, and
load capacity), and production options
determined by distributing to each axle
heater, to the extent that these items
weight.
its share of the maximum loaded vehi-
are available as factory-installed
cle weight and dividing by two.
equipment (whether installed or not).
Normal Occupant Weight - 68 kilo-
grams times the number of occupants
Vehicle Normal Load on the Tire - the
Cold Tire Inflation Pressure - the pres-
specified in the second column of
load on an individual tire that is deter-
sure in a tire that has been driven less
Table 1 (shown below).
mined by distributing to each axle its
than 1 mile or has been standing for
share of the curb weight, accessory
three hours or more.
Occupant distribution - distribution of
weight, and normal occupant weight
occupants in a vehicle as specified in
Curb Weight - the weight of a motor
(distributed in accordance with Table 1
the third column of Table
1 (shown
vehicle with standard equipment
shown below) and dividing by 2.
below).
including the maximum capacity of
fuel, oil, and coolant, and, if so
Production Options Weight - the com-
TABLE 1 - Occupant Loading and
equipped, air conditioning and addi-
bined weight of those installed regular
Distribution For Vehicle Normal
tional weight optional engine.
production options weighing over 2.3
Load For Various Designated Seat-
kilograms in excess of those standard
ing Capacities
Intended Outboard Sidewall - (1) the
items which they replace, not previ-
sidewall that contains a whitewall,
ously considered in curb weight or
Designated
Vehicle nor-
Occupant
bears white lettering or bears manu-
accessory weight, including heavy
seating
mal load,
distribution
facturer, brand, and/or model name
duty brakes, ride levelers, roof rack,
capacity,
number of
in a nor-
molding that is higher or deeper than
heavy duty battery, and special trim.
number of
occupants
mally loaded
the same molding on the other side-
occupants
vehicle
wall of the tire, or (2) the outward fac-
Recommended Inflation Pressure
-
ing sidewall of an asymmetrical tire
the cold tire inflation pressure recom-
2 through 4
2
2 in front
that has a particular side that must
mended by a manufacturer.
2 in front,
always face outward when mounted
Rim - metal support for a tire or tire
5 through 10
3
1 in second
on a vehicle.
and tube assembly upon which the tire
seat
beads are seated.
7-36

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Vehicle Loading
GVWR - Maximum permissible overall
trailer). Contact your dealer for further
Your vehicle was designed for specific
weight of the fully loaded vehicle
information.
load capacities. The load capacities of
(including all the occupants, accesso-
Actual weight of the loaded vehicle
your vehicle are indicated by the
ries and cargo plus the trailer tongue
and actual loads at the front and rear
Gross Vehicle Weight Rating (GVWR),
weight if towing a trailer).
axles can only be determined by
the Gross Axle Weight Rating (GAWR,
GAWR - (Front and Rear) Maximum
weighing the vehicle using a vehicle
front and rear), and the total load
permissible weight on an individual
scale. To measure the weight and
capacity, the seating capacity, and the
axle.
load, try making your vehicle to a high-
cargo load capacity. The GVWR and
way weighing station, shipping com-
GAWR (front and rear) are listed on
Seating Capacity - Maximum number
pany or inspection station for trucks,
the Safety Certification Label which is
of occupants the vehicle is designed to
etc. Compare these weights to the
located below the driver’s side door
carry.
GVWR and GAWR (front and rear)
latch striker. The total load capacity
listed on the Safety Certification Label.
and seating capacity are listed on the
NOTE:
If the gross vehicle weight or the load
Tire and Loading Information Label
Even though the number of occupants
on either axle exceeds these ratings,
which is located below the Safety Cer-
is within the seating capacity, you still
you must remove enough weight to
tification Label. The cargo load capac-
must make sure that you do not
bring the
load
down
to
the
rated
ity can be determined as described
exceed the total load capacity of the
capacity.
below.
vehicle.
Cargo Load Capacity
- Maximum
Total Load Capacity - Maximum per-
weight of cargo and luggage that the
missible weight a vehicle can carry
vehicle can safely carry. Cargo load
including the weight of all the occu-
capacity is the difference between the
pants, accessories, cargo, plus trailer
total load capacity of the vehicle and
tongue weight (if towing a trailer).
the total combined weight of all vehicle
occupants. Refer to “Steps for Deter-
The weight of any accessories already
mining Correct Load Limit” for details
installed on your vehicle at the time of
on how to determine cargo load
purchase, or that you or the dealer
capacity.
install after purchase, must be sub-
tracted from the total load capacity to
determine how much capacity remains
available for occupants, cargo, and
trailer tongue weight
(if towing a
7-37

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Steps for Determining Correct Load
Vehicle Loading Example
WARNING
Limit
As an example, suppose that the Tire
1) Locate the statement
“The com-
and Loading Information label on your
Never overload your vehicle. Over-
bined weight of occupants and
vehicle indicates that your vehicle’s
loading your vehicle can cause
cargo should never exceed XXX kg
total load capacity is 950 lbs. If you
damage to your tires and lead to
or XXX lbs” on your vehicle’s plac-
were to drive your vehicle with one
poor steering and braking which
ard.
passenger, and the total combined
can result in an accident. The
2) Determine the combined weight of
weight of you and your passenger was
gross vehicle weight (sum of the
the driver and passengers that will
350 lbs, then the cargo and luggage
weights of the loaded vehicle,
be riding in your vehicle.
capacity of your vehicle would be 600
driver and passengers) must
3) Subtract the combined weight of
lbs (950 - 350 = 600 lbs).
never exceed the Gross Vehicle
the driver and passengers from
If you later added 2 more passengers,
Weight Rating (GVWR) listed on
XXX kg or XXX lbs.
having a combined weight of 325 lbs,
the Safety Certification Label. In
4) The resulting figure equals the
the cargo and luggage capacity of
addition, never distribute a load so
available amount of cargo and lug-
your vehicle would be reduced from
that the weight on either the front
gage load capacity. For example, if
600 lbs to 275 lbs (600 - 325 = 275
or rear axle exceeds the Gross
the “XXX” amount equals 1400 lbs
lbs). As you can see, as the number
Axle Weight Rating (GAWR) listed
and there will be five 150 lb passen-
and combined weight of vehicle occu-
on the Safety Certification Label.
gers in your vehicle, the amount of
pants increase, the vehicle’s cargo
available cargo and luggage load
and luggage capacity decreases.
WARNING
capacity is 650 lbs (1400 - 750 (5 x
Suppose again, that you were to take
150) = 650 lbs).
a trip in your vehicle with the same
Always distribute cargo evenly.
5) Determine the combined weight of
three passengers described above,
To avoid personal injury or
luggage and cargo being loaded on
and you decided to tow a trailer having
damage to your vehicle, always
the vehicle. That weight may not
a trailer tongue weight of 75 lbs. The
secure cargo to prevent it from
safely exceed the available cargo
cargo and luggage capacity would be
shifting if the vehicle moves
and luggage load capacity calcu-
reduced again, to 200 lbs (275 - 75 =
suddenly.
lated in Step 4.
200 lbs).
Place heavier objects on the
6) If your vehicle will be towing a
floor and as far forward in the
trailer, load from your trailer will be
cargo area as possible. Never
transferred to your vehicle. Consult
pile cargo higher than the top of
this instruction to determine how this
the seatbacks.
reduces the available cargo and lug-
gage load capacity of your vehicle.
7-38

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Determining Compatibility of Tire
Battery
and Vehicle Load Limits
WARNING
The tires on your vehicle, when they
EXAMPLE
To avoid harm to yourself or damage
are inflated to the recommended tire
to your vehicle or battery, follow the
inflation pressure, have a load-carry-
jump starting instructions in the
ing capacity that is greater than the
“EMERGENCY SERVICE” section of
load that will be on the tires when the
this instruction if it is necessary to jump
vehicle is at its GVWR or GAWR limit.
start your vehicle.
Never use replacement tires that have
a load-carrying capacity less than the
original tires on your vehicle. Tire load-
WARNING
carrying capacity information is
Battery posts, terminals and related
molded into the tire sidewall typically
accessories contain lead and lead
shown as “Max. Load”. Use of replace-
compounds. Wash hands after han-
ment tires with a lower load-carrying
dling.
60A269
capacity than the original tires, or fail-
ure to keep the tires inflated to recom-
Your vehicle is equipped with a battery that
mended tire pressure, may reduce the
WARNING
requires infrequent maintenance. You will
GVWR or GAWR limit of your vehicle.
never have to add water. You should, how-
Batteries produce flammable hydro-
ever, periodically check the battery, battery
gen gas. Keep flames and sparks
NOTE:
terminals and battery hold-down bracket
away from the battery or an explosion
Use of replacement tires with a higher
for corrosion. Remove corrosion using a
may occur. Never smoke when work-
load-carrying capacity than the origi-
stiff brush and ammonia mixed with water,
ing near the battery.
nal tires, or using a tire inflation pres-
or baking soda mixed with water. After
removing corrosion, rinse with clean water.
sure higher than the recommended
tire inflation pressure, will not increase
WARNING
The test indicator on the top of the battery
the GVWR or GAWR limit of your vehi-
When checking or servicing the bat-
provides information on the condition of
cle.
tery, disconnect the negative cable.
the battery.
Be careful not to cause a short circuit
If your vehicle is not going to be driven for
by allowing metal objects to contact
a month or longer, disconnect the cable
the battery posts and the vehicle at
from the negative terminal of the battery to
the same time.
help prevent discharge.
7-39

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Fuses
Fuses in the Engine Compartment
NO.
AMPS
FUSE NAME
Your vehicle has three types of fuses, as
described below:
(1)
50A
Ignition switch
Main Fuse - The main fuse takes current
(2)
30A
Radiator fan sub
directly from the battery.
33
1
27
34
(3)
30A
Radiator fan main
2
28
23
Primary Fuses - These fuses are between
35
the main fuse and individual fuses, and are
3
29
(4)
30A
Starting motor
10
36
24
for electrical load groups.
4
11
30
37
(5)
40A
Light
5
12
31
25
38
Individual Fuses - These fuses are for indi-
13
32
6
39
(6)
40A
ESP control module
vidual electrical circuits.
14
19
26
7
15
20
Keyless start control
For details on protected circuits, refer to
8
16
21
(7)
50A
41
40
module
the “Fuses and Protected Circuits” section
17
22
9
18
42
in this instruction.
43
Power window, Power
44
(8)
50A
45
seat
To remove a fuse, use the fuse puller pro-
vided in the fuse box.
USE THE DESIGNATED
(9)
50A
Blower fan
FUSES AND RELAYS ONLY
Air conditioning com-
(10)
10A
pressor
(11)
15A
Door mirror heater
(12)
15A
Throttle motor
57L71037
(13)
30A
Rear defogger
(14)
30A
Blank
(15)
7.5A
Head light
(16)
20A
Fuel injection
(17)
25A
ESP control module
57L71011
(18)
25A
Back up
(19)
15A
Head light low (Left)
7-40

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
(20)
15A
Head light low (Right)
(39)
-
Fuel pump relay
(21)
15A
Head light high (Left)
(40)
-
Radiator fan relay 3
(22)
15A
Head light high (Right)
(41)
-
Radiator fan relay 1
OK
(23)
15A
CVT
Door mirror heater
(42)
-
relay
(24)
20A
Front fog light
(43)
-
Radiator fan relay 2
(25)
15A
O2 sensor heater
(44)
-
Main relay
(26)
15A
Horn
BLOWN
(45)
-
Throttle motor relay
Head light low
relay
(27)
-
(Left)
The main fuse, primary fuses and some of
Head light low
relay
the individual fuses are located in the
60A243
(28)
-
(Right)
engine compartment. If the main fuse
blows, no electrical component will func-
WARNING
(29)
-
Blank
tion. If a primary fuse blows, no electrical
component in the corresponding load
If the main fuse or a primary fuse
(30)
-
Blank
group will function. When replacing the
blows, be sure to have your vehicle
(31)
-
Blank
main fuse, a primary fuse or an individual
inspected by an authorized SUZUKI
fuse, use a genuine SUZUKI replacement.
dealer. Always use a genuine SUZUKI
Air conditioning
com-
(32)
-
To remove a fuse, use the fuse puller pro-
replacement. Never use a substitute
pressor relay
vided in the fuse box. The amperage of
such as a wire even for a temporary
(33)
-
Rear defogger relay
each fuse is shown in the back of the fuse
fix, or extensive electrical damage
box cover.
and a fire can result.
(34)
-
Blank
Windshield wiper relay
NOTE:
(35)
-
2
Make sure that the fuse box always carries
spare fuses.
(36)
-
Blank
Windshield wiper relay
(37)
-
1
(38)
-
Starting motor relay
7-41

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Fuses under the Dash Board
(11)
7.5A
IG1 SIG
Driver’s side
(12)
7.5A
Blank
1
EXAMPLE
(13)
7.5A
Meter
2
3
4
5
6
7
8
(14)
10A
Back-up light
(15)
10A
Air bag
9
10
11
12
13
14
15
16
17
(16)
15A
Steering lock
(17)
7.5A
BCM
18
19
20
21
22
23
24
25
26
(18)
20A
Sunroof
(1)
(19)
7.5A
Blank
57L70034
(20)
10A
Tail light
57L71012
NO.
AMPS
FUSE NAME
(21)
10A
Brake light
(1) Driver’s side fuse box
(1)
30A
Power window
(22)
10A
Hazard
Windshield
washer
(2)
15A
Front power
window
motor
(23)
20A
(3)
(Left)
(3)
20A
Seat heater
(2)
(24)
15A
Radio
(3)
(4)
25A
Windshield wiper motor
(25)
10A
Dome light
(5)
7.5A
IG2 SIG
(26)
20A
Door lock
(6)
15A
Ignition coil
The fuses are
also located under the
(7)
15A
Accessory 2
driver’s side of the dashboard. To access
(8)
15A
Accessory
these fuses, pull the dashboard under-
cover to release its clip engagements and
(9)
10A
ESP control module
then remove the undercover. The amper-
57L70027
age of each fuse is shown on the top of the
(10)
7.5A
Cruise control
(2) Dashboard undercover
dashboard undercover.
(3) Clips
7-42

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Passenger’s side
CAUTION
EXAMPLE
Remove the dashboard undercover
while being careful not to damage the
wiring fitted on it. If the wiring is dam-
aged, the courtesy lights will not
1
2
3
4
5
work.
6
7
8
9
(1)
57L70016
57L71013
(1) Passenger’s side fuse box
NO.
AMPS
FUSE NAME
Rear power window
(1)
20A
(3)
(Right)
Rear power window
(2)
20A
(Left)
Front power window
(3)
20A
(Right)
(4)
15A
4WD
(5)
20A
Battery fan
(2)
(6)
20A
Audio
(7)
30A
Power seat (Right)
57L70030
(8)
30A
Power seat (Left)
(2) Dashboard undercover
(3) Screw
(9)
30A
Blank
7-43

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
The fuses are also located under the pas-
Headlight Aiming
senger’s side of the dashboard. Remove
WARNING
Since special procedures are required, we
the two screws and dashboard under
Always be sure to replace a blown
recommend you take your vehicle to your
cover. The amperage of each fuse is
fuse with a fuse of the correct amper-
SUZUKI dealer for headlight alignment.
shown on the top of the dashboard under
age. Never use a substitute such as
cover.
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
CAUTION
the new one blows in a short period
of time, you may have a major electri-
Remove the dashboard undercover
cal problem. Have your vehicle
while being careful not to damage the
inspected immediately by your
wiring fitted on it. If the wiring is dam-
SUZUKI dealer.
aged, the courtesy lights will not
work.
OK
BLOWN
81A283
7-44

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Bulb Replacement
Interior Light
Rear dome Light
Front dome light
WARNING
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially
for halogen headlight bulbs.
Replace the bulbs after they
become cool enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
57L71015
CAUTION
57L71014
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
The oils from your skin may cause a
Pull down the lens by using a flat blade
shown. To install it, simply push it back in.
halogen bulb to overheat and burst
screwdriver covered with a soft cloth as
when the lights are on. Grasp a new
shown. To install it, simply push it back in.
The bulb can be removed by simply pulling
bulb with a clean cloth.
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
CAUTION
Frequent replacement of a bulb indi-
cates the need for an inspection of
the electrical system. This should be
carried out by your SUZUKI dealer.
NOTE:
If it is difficult to replace headlight bulbs or
position light bulbs due to under-hood
components trust this job to your dealer.
7-45

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Spot light
Pull down the lens by using a flat blade
Headlights
screwdriver covered with a soft cloth as
Low beam light
shown. To install it, simply push it back in.
1) Open the engine hood.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the
bulb securely.
Courtesy light
57L71016
(1)
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
57L71019
Vanity mirror light
2) Remove the cover (1) using a flat blade
screwdriver as shown in the illustration.
57L71018
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
(3)
shown. To install it, simply push it back in.
(2)
57L71017
57L71020
7-46

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
3) Remove the bolts (2) to remove the
5) Disconnect the coupler (5).
High beam light
bracket (3).
1) Open the engine hood.
(7)
(2)
(6)
(4)
(1)
57L71023
57L71021
6) Push the retainer (6) in the direction of
57L70036
4) Turn the cover (4) counterclockwise to
the arrow (see the illustration) to detach
2) To create the space necessary for per-
remove it.
it from the hook (7).
forming the steps that follow, discon-
7) Replace the bulb, then follow the above
nect the coupler (1) by pressing the
steps in reverse to restore the original
claw.
state.
(5)
57L71022
7-47

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
3) Turn the cover (2) counterclockwise to
5) Push the retainer (4) in the direction of
Other General Lights
remove it.
the arrow (see the illustration) to detach
Bulb holder
it from the hook (5).
6) Replace the bulb, then follow the above
EXAMPLE
(3)
steps in reverse to restore the original
state.
(2)
(1)
(2)
(1)
57L70037
54G123
4) Disconnect the coupler (3).
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
(4)
pull it out. To install the holder, push the
holder in and turn it clockwise.
(5)
57L70038
7-48

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
Bulb
Front parking lights
3) Turn the cover (2) counterclockwise to
remove it.
EXAMPLE
1) Open the engine hood.
(3)
(2)
(1)
(3)
(4)
(1)
(2)
54G124
(3) Removal
57L70037
57L70036
(4) Installation
4)
Disconnect the coupler (3).
2)
To create the space necessary for per-
There are two types of bulb, “Full glass
forming the steps that follow, discon-
type” (1) and “Glass/metal type” (2).
nect the coupler (1) by pressing the
claw.
(3)
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
(4)
holders as follows.
57L71027
7-49

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
5) Pull on the cable (4) toward the rear of
Side turn signal lights
2) Disconnect the coupler while pushing
the vehicle to remove the bulb socket
the lock release (2) on it.
(5) from the parking light body.
3) Replace the side turn signal light (1),
then follow the above steps in reverse
NOTE:
to restore the original state.
You can remove the parking light’s bulb
socket only by pulling on the cable, but this
Front fog light (if equipped)
method must never be used to remove the
1) Start the engine. To facilitate bulb
bulb sockets of any other lights.
replacement, turn the steering wheel
6) Replace the bulb, then follow the above
away from the front fog light whose bulb
steps in reverse to restore the original
(1)
is to be replaced, then turn off the
state.
engine.
EXAMPLE
57L71028
1)
Pull out the rear end of the side turn
signal light (1) while pushing it toward
the front of the vehicle as shown in the
illustration.
(1)
(2)
57L70039
2) Remove the screw (1).
57L71029
7-50

-------------------------------------------------------------------------------------------------------------------------------------------------------------

INSPECTION AND MAINTENANCE
EXAMPLE
EXAMPLE
EXAMPLE
(1)
(2)
(2)
(2)
57L70040
80JM071
57L70039
3) Remove the screws (2).
5) Disconnect the coupler with pushing
2) Remove the screw (1).
the lock release. Turn the bulb holder
counterclockwise and remove it.
EXAMPLE
6) Replace the bulb, then follow the above
steps in reverse to restore the original
state.
(3)
Side marker lights
1) Start the engine. To facilitate bulb
replacement, turn the steering wheel
away from the side marker light whose
(2)
(2)
(2)
bulb is to be replaced, then turn off the
engine.
57L70041
57L70040
4) Remove the part of the bumper (3) indi-
3) Remove the screws (2).
cated in the illustration.
7-51

 

 

 

 

 

 

 

Content      ..     17      18      19      20     ..