Nissan Versa Sedan. Instruction - part 886

TM-450

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

FLUID COOLER HOSE

FLUID COOLER HOSE

Exploded View

INFOID:0000000009315566

Removal and Installation

INFOID:0000000009315567

Inspection and Adjustment

INFOID:0000000009315568

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage. Refer to 

TM-426, "Inspection"

.

ADJUSTMENT AFTER INSTALLATION

Adjust the CVT fluid level. Refer to 

TM-427, "Adjustment"

.

PLUG

TM-451

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

PLUG

Description

INFOID:0000000009268276

Replace the O-ring if oil leakage or exudes from the plug.

Exploded View

INFOID:0000000009268277

Removal and Installation

INFOID:0000000009268278

REMOVAL

Remove the plugs and O-rings.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Do not reuse O-rings.

• Apply Genuine NISSAN CVT Fluid NS-3 to O-rings.

Inspection and Adjustment

INFOID:0000000009268279

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage. Refer to 

TM-426, "Inspection"

.

ADJUSTMENT AFTER INSTALLATION

Adjust the CVT fluid level. Refer to 

TM-427, "Adjustment"

.

1.

Plug

2.

O-ring

3.

O-ring

4.

Plug

Genuine NISSAN CVT Fluid NS-3

JSDIA1889GB

TM-452

< UNIT REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

TRANSMISSION ASSEMBLY

UNIT REMOVAL AND INSTALLATION

TRANSMISSION ASSEMBLY

Exploded View

INFOID:0000000009268280

Removal and Installation

INFOID:0000000009268281

WARNING:

• Do not open the radiator cap or drain plug when the engine is hot. Hot liquid may spray out, causing

serious injury.

• Perform these steps after the coolant temperature has cooled sufficiently.

NOTE:

• When replacing the TCM and transaxle assembly as a set, replace the transaxle assembly first and then

replace the TCM. Refer to 

TM-325, "Description"

.

• When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from

spilling.

REMOVAL

1. Remove the battery. Refer to 

PG-63, "Removal and Installation"

.

2. Remove the TCM. Refer to 

TM-437, "Removal and Installation"

.

3. Remove the battery plate.
4. Remove the air duct and air cleaner case. Refer to 

EM-25, "Removal and Installation"

.

5. Disconnect the harness connectors from the following components and remove the harness from the tran-

saxle.

1.

Transaxle assembly

A : For the tightening torque, refer to 

TM-452, "Removal and Installation"

.

JSDIA1890ZZ

TRANSMISSION ASSEMBLY

TM-453

< UNIT REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

• CVT unit. Refer to 

TM-258, "Removal and Installation Procedure for CVT Unit Connector"

.

• Transmission range switch

• Primary speed sensor

• Secondary speed sensor

• Output speed sensor

• Crankshaft position sensor. Refer to 

EM-94, "Exploded View"

.

• Ground

6. Disconnect the control cable from the transaxle assembly. Refer to 

TM-432, "Exploded View"

.

7. Disconnect the CVT water hose A and water hose C from engine side. 

TM-447, "Removal and Installa-

tion"

.

8. Disconnect the heater hose from the water bypass pipe.
9. Remove the left and right drive shafts. Refer to 

FAX-15, "Removal and Installation"

.

10. Remove the drive shaft heat insulator.
11. Remove starter motor. Refer to 

STR-31, "Removal and Installation"

.

12. Remove the right and left fender protectors. Refer to 

EXT-26, "Removal and Installation"

.

13. Rotate the crankshaft and remove the nuts that secure the drive plate to the torque converter.

CAUTION:

Rotate crankshaft clockwise (as viewed from the front of the engine).

14. Remove the rear torque rod. Refer to 

EM-82, "Exploded View"

.

15. Set a transmission jack under the transaxle assembly.

CAUTION:

Be careful not to contact the drain plug when setting the transmission jack.

16. Set a transmission jack under the engine assembly.

CAUTION:

Be careful not to contact the drain plug when setting the transmission jack.

17. Remove the left engine mounting insulator. Refer to 

EM-82, "Exploded View"

.

18. Remove the left engine mounting bracket (LH). Refer to 

EM-82, "Exploded View"

.

19. Remove the bolts that fasten the transaxle assembly and engine assembly.
20. Remove the transaxle assembly from the vehicle.

CAUTION:

Do not drop the torque converter.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Do not reuse O-rings. 

• Apply Genuine NISSAN CVT Fluid NS-3 to the O-rings.

• When installing the transaxle assembly onto the engine assembly,

check the engagement of the dowel pins (

).

JSDIA1184ZZ