Nissan Versa Sedan. Instruction - part 885

TM-446

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

DIFFERENTIAL SIDE OIL SEAL

Adjust the CVT fluid level. Refer to 

TM-427, "Adjustment"

.

WATER HOSE

TM-447

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

WATER HOSE

Exploded View

INFOID:0000000009268273

Removal and Installation

INFOID:0000000009268274

REMOVAL

WARNING:

Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure

coolant escaping from the radiator.

CAUTION:

Perform these steps after the coolant temperature has cooled sufficiently.
1. Remove the hose clamp and pull out the water hose A.
2. Remove the hose clamp and pull out the water hose B.
3. Remove the hose clamp and pull out the water hose C.
4. Pull out the heater hose and remove the water bypass pipe.
5. Remove the heater thermostat assembly.
6. Remove the bracket.

INSTALLATION

Installation is in the reverse order of removal.

1.

Hose clamp

2.

Water hose A

3.

Bracket

4.

Heater thermostat

5.

Water hose B

6.

Water hose C

7.

Water bypass pipe

8.

Hose clamp

9.

Heater hose

9.

Water hose D

A. Water outlet

B. Oil warner

C. To heater core

AWBIA1483ZZ

TM-448

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

WATER HOSE

• To install bracket to the CVT assembly, face the front arrow (A) of

the bracket toward front of vehicle.

• Refer to the following when installing water hoses.

• Refer to the following when installing hose clamp.

CAUTION:

Hose clamp should not interfere with the bulge of fluid cooler tube.

JSDIA1838ZZ

Water hose (1)

Installation side tube (2)

Direction of paint mark

Hose insertion depth (L)

Water hose A

Water outlet

Align with the mark on the water 
outlet side

(A): 27 mm (1.06 in) (End reaches 
the 2-stage bulge.)

Heater thermostat

Frontward

(B): 27 mm (1.06 in) (Hose end 
reaches the 2-stage bulge.)

Water hose B

Heater thermostat

Frontward

CVT oil warmer

Frontward

(A): 27 mm (1.06 in) (End reaches 
the 2-stage bulge.)

Water hose C

CVT oil warmer

Align with the mark on the CVT 
oil warmer side

Water bypass pipe

Align with the mark on the water 
bypass pipe side

Water hose D

Water bypass pipe

Align with the mark on the water 
bypass pipe side

Water outlet

Align with the mark on the water 
outlet side

JSDIA3579ZZ

WATER HOSE

TM-449

< REMOVAL AND INSTALLATION >

[CVT: RE0F11A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Inspection

INFOID:0000000009268275

INSPECTION AFTER REMOVAL

Heater Thermostat

1. Fully immerse the heater thermostat (1) in a container (A) filled

with water. Continue heating the water while stirring.

2. Continue heating the heater thermostat for 5 minutes or more

after bringing the water to a boil.

3. Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.

-

Place dial indicator (A) on the pellet (B) and measure the elon-

gation from the initial state.

4. If out of standard, replace heater thermostat.

INSPECTION AFTER INSTALLATION

Start the engine, and check the joints for coolant leakage.

Water hose (1)

Installation side 

tube (2)

Hose clamp (3)

Dieection of tab

Clamping position

Water hose A

Water outlet

Upward

5 - 7 mm (0.20 - 0.25 
in) (A) from hose end

Heater thermostat

Frontward

5 mm (0.20 in) (A) 
from hose end

Water hose B

Heater thermostat

Frontward

CVT oil warmer

Frontward

5 - 7 mm (0.20 - 0.25 
in) (A) from hose end

Water hose C

CVT oil warmer

Frontward

Water bypass pipe Rightward

Water hose D

Water bypass pipe

Upward and 45

° 

frontward

Water outlet

Upward and 45

° 

frontward

JSDIA2424ZZ

JSDIA3661ZZ

Standard

: Refer to 

TM-457, "Heater Thermostat"

.

JSDIA3662ZZ