Nissan Versa Sedan. Instruction - part 388

ENGINE STAND SETTING

EM-87

< UNIT DISASSEMBLY AND ASSEMBLY >

[HR16DE]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

3. Drain engine coolant by removing water drain plug (1) from

inside of the engine. 

Use Genuine Silicone RTV Sealant or equivalent. Refer to

GI-21, "Recommended Chemical Products and Sealants"

.

: Engine front

Water drain plug 
tightening torque

: Refer to 

EM-94, "Exploded View"

.

PBIC3742E

EM-88

< UNIT DISASSEMBLY AND ASSEMBLY >

[HR16DE]

ENGINE UNIT

ENGINE UNIT

Disassembly

INFOID:0000000009266672

1. Remove intake manifold. Refer to 

EM-27, "Exploded View"

.

2. Remove exhaust manifold. Refer to 

EM-30, "Exploded View"

.

3. Remove oil pan (lower). Refer to 

EM-33, "Exploded View"

.

4. Remove ignition coil, spark plug, and rocker cover. Refer to 

EM-44, "Exploded View"

.

5. Remove fuel injector and fuel tube. Refer to 

EM-37, "Exploded View"

.

6. Remove front cover and timing chain. Refer to 

EM-47, "Exploded View"

.

7. Remove camshaft. Refer to 

EM-56, "Exploded View"

.

8. Remove cylinder head. Refer to 

EM-73, "Exploded View"

.

Assembly

INFOID:0000000009266673

Assembly is in the reverse order of disassembly.

OIL PAN (UPPER) AND OIL STRAINER

EM-89

< UNIT DISASSEMBLY AND ASSEMBLY >

[HR16DE]

C

D

E

F

G

H

I

J

K

L

M

A

EM

N

P

O

OIL PAN (UPPER) AND OIL STRAINER

Exploded View

INFOID:0000000009266674

Removal and Installation

INFOID:0000000009266675

NOTE:

The oil strainer is included in the oil pan (upper) and cannot be removed. 

REMOVAL

1. Remove the oil pan (lower). Refer to 

EM-33, "Exploded View"

.

1.

Rear oil seal

2.

O-ring

3.

Oil pan (upper)

4.

Oil pump chain tensioner (for oil 
pump drive chain)

5.

Oil pump drive chain

6.

Crankshaft key

7.

Crankshaft sprocket

8.

Oil pump sprocket

9.

Oil pump

10. O-ring

11. O-ring

12. Oil pan drain plug

13. Drain plug washer

14. Oil pan (lower)

15. Oil filter

16. Connector bolt

17. Oil cooler

18. O-ring

19. Relief valve

A.

Refer to 

EM-47

B.

Refer to 

LU-11

C.

Oil pan (lower) side

AWBIA1477ZZ

EM-90

< UNIT DISASSEMBLY AND ASSEMBLY >

[HR16DE]

OIL PAN (UPPER) AND OIL STRAINER

2. Remove oil pump sprocket and crankshaft sprocket together with oil pump drive chain. Refer to 

EM-47,

"Exploded View"

.

3. Remove oil pan (upper).
a. Loosen oil pan (upper) bolts in the reverse of the order as

shown.

b. Insert a suitable tool into the arrow (

) as shown and open up a

crack between the oil pan (upper) cylinder block.

c.

Insert the Tool between the oil pan (upper) and cylinder block.

Slide Tool by tapping on the side of Tool with a hammer.

CAUTION:

• Be careful not to damage the mating surface.

• The liquid gasket used at the factory is very strong. Pry only in the areas shown.

• Do not remove oil pump and oil strainer from oil pan (upper).

4. Remove rear oil seal from crankshaft.

INSTALLATION

CAUTION:

Do not reuse O-rings or washers.
1. Install the oil pan (upper):
a. Use scraper to remove old liquid gasket from mating surfaces.

• Also remove the old liquid gasket from mating surface of cylinder block.

• Remove old liquid gasket from the bolt holes and threads.

CAUTION:

Do not scratch or damage the mating surfaces when cleaning off old liquid gasket.

b. Install O-ring to the cylinder block.

: Engine front

JPBIA4199ZZ

: Engine front

Tool number

: KV10111100 (J-37228)

JPBIA4200ZZ