Nissan Versa Sedan. Instruction - part 249

DLK-314

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

FUEL FILLER LID OPENER

Exploded View

INFOID:0000000009269023

FUEL FILLER LID
FUEL FILLER LID : Removal and Installation

INFOID:0000000009269024

REMOVAL 

1. Fully open fuel filler lid. 
2. Remove fuel cap pin (1).

3. Remove fuel filler lid screws and fuel filler lid.

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

1.

Fuel filler lid opener cable

2.

Spring

3.

Fuel filler lid assembly

4.

Bumper rubber

5.

Fuel filler lid lock assembly

6.

Cable protector

Clip

JMKIA8174ZZ

JMKIA8137ZZ

FUEL FILLER LID OPENER

DLK-315

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000009269025

REMOVAL 

1. Remove hood and fuel filler handle assembly bolts (A).

2. Disconnect fuel filler lid opener cable (2) by pulling downward

and then sliding cable end to the side to remove from hood and

fuel filler handle assembly (1).

3. Remove dash side finisher (LH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installation"

.

4. Remove center pillar lower finisher (LH). Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER :

Removal and Installation"

.

5. Remove trunk side finisher (LH). Refer to 

INT-33, "TRUNK SIDE FINISHER : Removal and Installation"

.

6. Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to 

DLK-316, "FUEL FILLER LID

LOCK : Removal and Installation"

.

7. Disengage each harness protector (1), and then remove fuel

filler lid opener cable (2).

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

NOTE:

• The following table shows the specifications for a correctly installed fuel filler lid.

• Fitting adjustment cannot be performed.

JMKIA7998ZZ

JMKIA7999ZZ

JMKIA5720ZZ

DLK-316

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

Unit: mm (in)

FUEL FILLER LID LOCK
FUEL FILLER LID LOCK : Removal and Installation

INFOID:0000000009269026

REMOVAL 

1. Fully open fuel filler lid.
2. Remove trunk side finisher (LH). Refer to 

INT-33, "TRUNK SIDE FINISHER : Removal and Installation"

.

3. Release pawls (A) and remove fuel filler lid lock assembly (1)

from opening.

CAUTION:

Be careful not to damage gasket (2) when removing.

4. Disconnect fuel filler lid opener cable (1) by pulling downward

and then sliding cable end to the side to remove from fuel filler

lid lock assembly (2).

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

Portion

Measurement

Standard

Fuel filler lid – Body side outer

Clearance

3.0 

± 1.0 (0.12 ± 0.04)

Fuel filler lid – Body side outer

Surface height

0.0 

± 1.0 (0.0 ± 0.04)

JMKIA8138ZZ

JMKIA8139ZZ

DOOR SWITCH

DLK-317

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR SWITCH

Exploded View

INFOID:0000000009269027

Removal and Installation

INFOID:0000000009269028

REMOVAL

1. Remove the door switch bolt (A).
2. Disconnect the harness connector from door switch (1) and

remove.

INSTALLATION

Installation is in the reverse order of removal.

1.

Door switch

2.

Door switch bolt

AWKIA1893ZZ

JMKIA2173ZZ