Nissan Versa Sedan. Instruction - part 248

DLK-310

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

REAR DOOR LOCK

6. Pull outside handle (1) rearward and outward to remove.

7. Remove front gasket (1) and rear gasket (2).

: Front

8. Slide outside handle bracket toward rear of vehicle to remove.

: Front

9. Disconnect outside handle cable (1) from outside handle bracket

(2) as shown.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check door open/close, lock/unlock operation. 

• Check door lock cable is properly engaged with outside handle bracket.

JMKIA0524ZZ

JMKIA5889ZZ

JMKIA5890ZZ

JMKIA5891ZZ

TRUNK LID LOCK

DLK-311

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

TRUNK LID LOCK

Exploded View

INFOID:0000000009269018

TRUNK LID LOCK
TRUNK LID LOCK : Removal and Installation

INFOID:0000000009269019

REMOVAL

1. Remove trunk lid finisher (If equipped). Refer to 

INT-35, "Removal and Installation"

.

2. Disengage rod holder (1) by lifting upward, and then separate

trunk lid lock rod (3) from trunk lid lock assembly (2).

3. Remove trunk lid lock assembly bolts.

1.

Trunk lid opener handle

2.

Trunk lid opener cable

3.

Cable protector

4.

Trunk lid striker

5.

Trunk lid lock assembly

6.

Key rod

7.

Trunk key cylinder

JMKIA8173GB

JMKIA8131ZZ

DLK-312

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

TRUNK LID LOCK

4. Disconnect the harness connector and then remove trunk lid

lock assembly (1).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check trunk lid open/close, lock/unlock operation. 

• Check trunk lid lock assembly for poor lubrication. Apply a

suitable multi-purpose grease to trunk lid lock if necessary.

TRUNK LID OPENER HANDLE
TRUNK LID OPENER HANDLE : Removal and Installation

INFOID:0000000009269020

REMOVAL

1. Remove front kicking plate (LH). Refer to 

INT-20, "KICKING PLATE INNER : Removal and Installation"

.

2. Release pawl using a suitable tool (A) and open the harness

clip.

: Pawl

3. Position floor carpet aside as necessary to access the trunk lid opener handle bolts.
4. Remove the trunk lid opener handle bolts.
5. Remove trunk lid opener cable from trunk lid opener handle.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check trunk lid open/close, lock/unlock operation.

• After installation, perform the trunk lid adjustment procedure. Refer to 

DLK-285, "DOOR ASSEMBLY

: Adjustment"

.

TRUNK LID OPENER CABLE

JMKIA8132ZZ

JMKIA8133ZZ

AWJIA0737ZZ

TRUNK LID LOCK

DLK-313

< REMOVAL AND INSTALLATION >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

TRUNK LID OPENER CABLE : Removal and Installation

INFOID:0000000009269021

REMOVAL

1. Remove trunk lid striker. Refer to 

DLK-295, "TRUNK LID STRIKER : Removal and Installation"

.

2. Remove trunk side finisher (LH). Refer to 

INT-33, "TRUNK SIDE FINISHER : Removal and Installation"

.

3. Remove rear seat cushion. Refer to 

SE-23, "Removal and Installation - Seat Cushion Assembly"

.

4. Remove center pillar lower finisher (LH). Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER :

Removal and Installation"

.

5. Remove trunk lid opener handle. Refer to 

DLK-312, "TRUNK LID OPENER HANDLE : Removal and

Installation"

.

6. Release pawl using a suitable tool (A) and open the harness

clip.

: Pawl

7. Remove trunk lid opener cable.

CAUTION:

Use care not to damage the trunk lid opener cable when removing.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

After installation, perform the trunk lid adjustment procedure. Refer to 

DLK-294, "TRUNK LID ASSEM-

BLY : Adjustment"

.

EMERGENCY LEVER
EMERGENCY LEVER : Removal and Installation

INFOID:0000000009269022

Removal

1. Release the pawls using a suitable tool and remove emergency

release handle (1) from trunk lid assembly.

: Pawl

2. Disconnect emergency release handle cable (2) from trunk lid

lock assembly (3).

AWJIA0737ZZ

ALKIA2310ZZ