Chrysler Voyager. Manual - part 390

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  388  389  390  391   ..

 

 

Chrysler Voyager. Manual - part 390

 

 

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Multi-Function Switch harness connector.
Disconnect the BCM C5 harness connector.
Measure the between the Front Wiper Switch MUX circuit and the Multi-Function
Switch MUX Return circuit.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Front Wiper Switch MUX circuit for a short to the

Multi-Function Switch MUX Return circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the Multi-Function Switch harness connector.
Turn the ignition on.
With the DRB, read the Front Wiper Sw volts?
Is the voltage above 4.5 volts?

All

Yes

→ Replace the Multi-Function Switch.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Body Control Module.

Perform BODY VERIFICATION TEST - VER 1.

987

WINDSHIELD WIPER & WASHER

FRONT WIPER SWITCH MUX INPUT SHORT TO GROUND —

Continued

Symptom:

HEADLAMP WASHER RELAY OPEN

POSSIBLE CAUSES

OPEN GROUND CIRCUIT

FUSED B+ CIRCUIT OPEN

HEADLAMP WASHER RELAY CONTROL CIRCUIT OPEN

HEADLAMP WASHER RELAY OUTPUT CIRCUIT OPEN

HEADLAMP WASHER PUMP MOTOR

HEADLAMP WASHER RELAY

FRONT CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the Washer Pump connector.
Measure the resistance of the Washer Pump ground circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 2

No

→ Repair the open Washer Pump ground circuit.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition on.
Disconnect the Headlamp Washer Relay.
Measure the voltage of the Fused B+ Circuit.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 3

No

→ Repair the Fused B+ Circuit for an open condition.

Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
Disconnect the Headlamp Washer Relay.
Disconnect the FCM harness connector.
Measure the resistance of the Headlamp Washer Relay Control Circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

No

→ Repair the Headlamp Washer Relay Control Circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

4

Disconnect the Headlamp Washer Relay.
Disconnect the Headlamp Washer Pump Motor.
Measure the resistance of the Headlamp Washer Relay Output Circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair the Headlamp Washer Relay Output Circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

988

WINDSHIELD WIPER & WASHER

TEST

ACTION

APPLICABILITY

5

Turn the ignition on.
Disconnect the Headlamp Washer Pump Motor connector.
Actuate the washers.
Measure the voltage of the Washer Pump Output Circuit.
Is the voltage above 10.0 volts?

All

Yes

→ Replace the Headlamp Washer Pump Motor.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Install a known good relay in place of the Headlamp Washer Relay.
Turn the Washers on.
Do the Headlamp Washers operate normally?

All

Yes

→ Replace the Headlamp Washer Relay.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Front Control Module.

Perform BODY VERIFICATION TEST - VER 1.

989

WINDSHIELD WIPER & WASHER

HEADLAMP WASHER RELAY OPEN —

Continued

Symptom:

HEADLAMP WASHER RELAY SHORT TO BATT

POSSIBLE CAUSES

FUSED B+ CIRCUIT OPEN

HEADLAMP WASHER RELAY CONTROL CIRCUIT OPEN

HEADLAMP WASHER PUMP MOTOR

HEADLAMP WASHER RELAY

FRONT CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Disconnect the Headlamp Washer Relay.
Measure the voltage of the Fused B+ Circuit.
Is the voltage above 10.0 volts?

All

Yes

→ Go To 2

No

→ Repair the Fused B+ Circuit for an open condition.

Perform BODY VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Headlamp Washer Relay.
Disconnect the FCM harness connector.
Measure the resistance of the Headlamp Washer Relay Control Circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 3

No

→ Repair the Headlamp Washer Relay Control Circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition on.
Disconnect the Headlamp Washer Pump Motor connector.
Actuate the washers.
Measure the voltage of the Washer Pump Output Circuit.
Is the voltage above 10.0 volts?

All

Yes

→ Replace the Headlamp Washer Pump Motor.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Turn the ignition off.
Install a known good relay in place of the Headlamp Washer Relay.
Turn the Washers on.
Do the Headlamp Washers operate normally?

All

Yes

→ Replace the Headlamp Washer Relay.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Front Control Module.

Perform BODY VERIFICATION TEST - VER 1.

990

WINDSHIELD WIPER & WASHER

 

 

 

 

 

 

 

Content   ..  388  389  390  391   ..