|
|
|
Chapter 5
HONEYCOMB
LAYERS
AMMUNITION
BOXES
LOAD SPREADERS
(¾-IN PLYWOOD)
HONEYCOMB
STRIPS
(6-IN WIDE)
HONEYCOMB
SKID
STRIPS
(4-IN WIDE)
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-45.
Grenades
Grenade, Discharger, Anti-Riot, Irritant, L96E1, (DODIC 1330-FZ14)
Grenade, Discharger, Anti-Riot, Irritant, L97E1, (DODIC 1330-FZ15)
Figure 5-45. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
5-50
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
AMMUNITION
BOXES
HONEYCOMB
FILLERS
HONEYCOMB
LAYERS
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-46.
81-Millimeter Ammunition
Cartridge, 81-mm,Illuminating, IR, M816, (DODIC 1315-C484)
Figure 5-46. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-51
Chapter 5
HONEYCOMB
FILLER
HONEYCOMB
AMMUNITION
LAYER
LOAD SPREADERS
(¾-IN PLYWOOD)
HONEYCOMB
STRIPS
(6 1/2-IN WIDE)
HONEYCOMB
STRIPS
(6-IN WIDE)
SKID
ADD 50 POUNDS
OF BALLAST
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-47.
Munition
Munition, Wide Area, Hornet, M93, (DODIC 1377-SQ20)
Figure 5-47. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
5-52
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
ADDITIONAL
HONEYCOMB
A-7A STRAP
FILLERS
AMMUNITION
BOXES
LOAD SPREADERS
2 LAYERS
(¾-IN PLYWOOD)
HONEYCOMB
LAYERS
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-48.
120-Millimeter Ammunition
Cartridge, 120-mm, Visible, Illuminating, M930 w/ M230 Propellant Charge and
M981 Ignition Charge, (DODIC 1315-C625)
Cartridge, 120-mm, Illuminating, Infrared (IR), M983 (DODIC 1315-CA07)
Figure 5-48. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-53
Chapter 5
AMMUNITION
BOXES
HONEYCOMB
STRIPS
LOAD SPREADER
(5-IN WIDE)
(¾-IN PLYWOOD)
HONEYCOMB
LAYERS
HONEYCOMB
STRIPS
(6-IN WIDE)
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-49.
84-Millimeter Ammunition
Cartridge, 84-mm, Practice, w/ Tracer, TPT141, (DODIC 1315-CA10)
Cartridge, 84-mm, HEDP, IM, 502, (DODIC 1315-CA21)
Cartridge, 84-mm, MAAWS, Reduced Sensitivity (RS), 441D,
(DODIC 1315-CA27)
Figure 5-49. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
5-54
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
AMMUNITION
BOXES
HONEYCOMB
STRIPS
LOAD SPREADER
(5-IN WIDE)
(¾-IN PLYWOOD)
HONEYCOMB
LAYERS
HONEYCOMB
STRIPS
(6-IN WIDE)
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-50.
84-Millimeter Ammunition
Munition, 84-mm, Area Deterrent, 401, (DODIC 1315-CA23)
Cartridge, 84-mm, MAAWS, 545C, Illumination, (DODIC 1315-CA36)
Figure 5-50. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-55
Chapter 5
AMMUNITION
BOXES
LOAD SPREADER
HONEYCOMB
(¾-IN PLYWOOD)
LAYERS
HONEYCOMB
HONEYCOMB
STRIPS
SKID
(4-IN WIDE)
STRIPS
(6-IN WIDE)
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-51.
84-Millimeter Ammunition
Munition, 84-mm, HEAT, Insensitive, 551C, (DODIC 1315-CA20)
Figure 5-51. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
5-56
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
¾-IN PLYWOOD
AMMUNITION
BOXES
HONEYCOMB
LAYERS
LOAD SPREADER
(¾-IN PLYWOOD)
HONEYCOMB
STRIPS
(6-IN WIDE)
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-52.
Grenade
Grenade, Rifle, Entry, M100, (DODIC 1330-GG12)
Figure 5-52. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-57
Chapter 5
AMMUNITION
HONEYCOMB
BOXES
LAYERS
HONEYCOMB
SKID
STRIPS
(5-IN WIDE)
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-53.
7.62-Millimeter Ammunition
Cartridge, 7.62-mm, Linked, 9-Ball, M80, 1Tracer, M276, (DODIC 1305-A257)
Cartridge, 7.62-mm, Linked, 9-Ball, M80, 1Tracer, M62, (DODIC 1305-A165)
Figure 5-53. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
5-58
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
HONEYCOMB
AMMUNITION
FILLERS
BOXES
LOAD SPREADERS
2 LAYERS
(¾-IN PLYWOOD)
HONEYCOMB
LAYERS
SKID
The following ammunition item is rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-54.
60-Millimeter Ammunition
Cartridge, 60-mm, M720A1, (DODIC 1310-BA16)
Cartridge, 60-mm, M768, (DODIC 1310-BA17)
Figure 5-54. Ammunition Layout in an A-7A Cargo Sling or an A-21 Cargo Bag for High-
Velocity Airdrop
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-59
Chapter 5
CAUTIONS
1. The suspended weight of this load must be between 295 pounds
and 305 pounds.
2. The ballast used in the BCC must be contained (i.e. tied sandbags)
so it does not leak outside the BCC.
30”
48”
HONEYCOMB
LAYER
BALLAST CONTAINMENT
COMPARTMENT
Note: The ballast containment compartment and top layer of honeycomb
are placed inside the sling assembly and cover of the A-21 cargo bag and
inside the straps of an A-7A cargo sling.
HONEYCOMB
STRIPS
(6-IN WIDE)
HONEYCOMB
STRIPS
SKID
(6-IN WIDE)
6. Build the Ballast Containment Compartment (BCC) using two pieces of 2- by 4- by 48-inch
lumber, two pieces of 2- by 4- by 27-inch lumber, and two pieces of 30- X 48- X 3/4-inch
plywood. Do not nail the top piece of plywood until after the ballast has been added. The
weight of the BCC is approximately 56 pounds.
7. The combined weight of the BCC, Ballast, and the Modernized Demolition Initiator (MDI)
items must be between 295 and 305 pounds.
8. Weigh the MDI items, add 56 pounds (weight of the BCC), and subtract this sum from 300.
This figure is the amount of ballast weight that must be added in the BCC. Evenly
distribute the ballast in the BCC and fill all empty spaces with honeycomb
so the ballast does not move. Nail the top on the BCC.
Figure 5-55. Honeycomb Stack and Rigging Steps for the MDI Munitions in an A-7A Cargo
Sling or an A-21 Cargo Bag for High-Velocity Airdrop
5-60
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Rigging High-Velocity A-7A Cargo Slings and A-21 Cargo Bag Loads
9. Prepare and position the load on the honeycomb stack shown above in accordance with FM
4-20.103/MCRP 4-11.3C/TO13C7-1-11, Chapter 6, Section III. The following restrictions
apply:
The containers (wooden crates) may be broken down into smaller packaging units.
Individual corrugated cardboard boxes.
Individual foil wrapped items.
MDI items maybe rigged for airdrop up to their smallest unit of packaging.
MDI items in their smallest unit of packaging must be encased in a honeycomb bin. See
Appendix B for fabrication of honeycomb bins.
No container may be rigged on top of a honeycomb bin except another honeycomb bin.
Only honeycomb bins and corrugated cardboard boxes may be rigged on top of corrugated
cardboard boxes.
Wooden crates can only be stacked on top of other wooden crates.
Corrugated cardboard boxes containing spools of shock tubing (M12, M13) must be positioned
so the spools are lying flat on their base.
10. Center the load on the A-7A/A-21 container. Place honeycomb on all four sides of the bundle
and secure the honeycomb with Type III nylon cord. Place a piece of honeycomb over the top
of the load and position a piece of 3/4-inch plywood on top of the honeycomb. Close and
secure the A-7A/A-21 container.
The following ammunition items are rigged in an A-7A cargo sling or an A-21 cargo bag for high-velocity
airdrop as shown in Figure 5-55.
Modernized Demolition Initiators
Holder, Blasting Cap, M9, (DODIC 1375-ML45)
Cap, Blasting, Nonelectric, 30 foot Shock Tube, M11 (1.4B), (DODIC 1375-ML47)
Cap, Blasting, Nonelectric, 500 foot Shock Tube, M12 (1.4S), (DODIC 1375-MN02)
Cap, Blasting, Nonelectric, 1000 foot Shock Tube, M13 (1.4S), (DODIC 1375-MN03)
Cap, Blasting, Nonelectric, Delay, M14 (1.4S), (DODIC 1375-MN06)
Cap, Blasting, Nonelectric, Delay, M15, (DODIC 1375-MN07)
Ignitor, Time Blasting Fuze, M81, w/ Shock Tube Capability (1.4S), (DODIC 1375-
MN08)
Cap, Blasting, Non-Electric, M16, (DODIC 1375-MN39)
Cap, Blasting, Non-Electric, M18, (DODIC 1375-MN41)
Cap, Blasting, Dual, In-line Initiator, Non-Electric, 200-ft Minitube, M19, (DODIC
1375-MN86)
Trainer, Inert (for M19), M20, (DODIC 1375-MN87)
Cap, Blasting, Dual, In-line Initiator, Non-Electric, 500-ft Minitube, M21, (DODIC
1375-MN88)
Trainer, Inert (for M21 and M23), M22, (DODIC 1375-MN89)
Cap, Blasting, Dual, In-line Initiator, Non-Electric, 1000-ft Minitube, M21, (DODIC
1375-MN90)
Figure 5-55. Honeycomb Stack and Rigging Steps for the MDI Munitions in an A-7A Cargo
Sling or an A-21 Cargo Bag for High-Velocity Airdrop (continued)
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
5-61
Appendix A
Equipment Required
National Stock Number
Item
8040-00-273-8713
Adhesive, Paste, 1-gal
1670-00-242-9173
Bag, Cargo, Aerial Delivery, A-21
1670-00-587-3421
Bag, Cargo, Aerial Delivery, A-22
4030-00-678-8562
Clevis Assembly, Medium, 3/4-Inch, Shackle
1670-01-523-7246
Container, Low Cost
4020-00-240-2146
Cord, Nylon, Type III, 550-lb
8135-00-664-6958
Cushioning Material, Cellulose Padding
8305-00-958-3685
Felt, Sheet, 1/2-Inch
3540-00-565-6242
Kit, Steel Strapping and Sealing, 5/8-Inch
1670-00-753-3928
Pad, Energy, Dissipating, Honeycomb
Parachute Cargo:
1670-01-065-3755
G-12E
1670-00-999-2658
G-14
Parachute, Cargo, Extraction:
1670-01-063-3715
15-foot
1670-01-063-3716
22-foot
Parachute, Cargo, High-Velocity:
1670-00-788-8666
12-foot
1670-00-872-6109
26-foot
1670-01-529-1202
Parachute, Low Cost, High-Velocity
1670-00-216-7297
Parachute, Pilot, 68-Inch
5530-00-128-4981
Plywood, 3/4-Inch
5530-00-914-5118
Plywood, 1-Inch
8135-00-290-1086
Seal, Steel, Strapping, 5/8-Inch
1670-01-342-5913
Skid, Cargo Bag, Platform, Plywood, 1”(CDS)
1670-00-251-1153
Sling, Cargo, A/D, 500-lb Capacity, 188-Inch, A-
7A
1670-01-062-6301
Sling, Cargo, A/D, 3-ft (2 Loop) Type XXVI
8135-00-283-0667
Strapping, Steel, 5/8-Inch
8305-00-074-5124
Tape, Adhesive, 2-Inch
8310-00-917-3945
Thread, Cotton, 8/7 (Ticket #5)
Webbing:
8305-00-268-2411
Cotton, 1/4-Inch, Type I
8305-00-082-5752
Nylon, Tubular, 1/2-Inch
8305-00-263-3591
Nylon, Type VIII
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
A-1
Appendix B
Fabrication of Honeycomb Bin
INTRODUCTION
The honeycomb bin is used to airdrop certain certified munitions when they are broken down into
smaller units of issue. The munitions are placed into the bin and all unused space is filled with
cellulose padding or honeycomb.
RIGGING THE HONEYCOMB BIN
Rig the honeycomb bin using the procedures shown below.
BASE MEASUREMENT + 4
INCHES
TOP
2”-WIDE
SIDEWALL
HEIGHT IN INCHES DIVIDED BY
3 INCHES, ROUNDED TO NEXT
HIGHEST NUMBER, EQUALS
THE NUMBER OF LAYERS FOR
THE SIDEWALLS
BASE MEASUREMENT + 4
INCHES
BOTTOM
11. Calculate the combined length and width of the base for the items that are to be rigged in the
honeycomb bin. Add 4 inches to the length and 4 inches to the width of the base
measurement. These are the measurements for the pieces of honeycomb used to make the
honeycomb bin (top, bottom, and sidewalls).
12. Measure the combined height of the items that are to be rigged in the honeycomb bin. Divide
the height in inches by 3 inches. Round off any fraction or remainder to the next highest
number. This is the number of layers required for the honeycomb bin sidewalls.
13. Draw a line 2 inches from each side of the sidewalls. Remove the honeycomb rectangle
formed by the drawn lines. This leaves a 2 inch wide rim on the sidewalls.
Honeycomb Bin
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
B-1
Appendix B
14. Glue the sidewall layers together. Place the sidewalls on the bottom layer of honeycomb.
15. Position and pad the munitions inside the bin. Fill all empty areas with honeycomb or
cellulose padding.
16. Place the top on the bin and secure the top and bottom with type III nylon cord. Tape the
edges of the bin where necessary to prevent the type III nylon cord from cutting into the
honeycomb.
Honeycomb Bin (continued)
B-2
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Glossary
A/C
aircraft
acft
aircraft
ADAM
Area denial artillery munition
AFB
Air Force Base
AFR
Air Force regulation
AFTO
Air Force Technical Order
AP
armor-piercing
APC-T
armor-piercing capped tracer
APDS-T
armor-piercing discarding sabot-tracer
APERS
antipersonnel
APERS-T
antipersonnel—tracer
APFSDS-T
armor-piercing fin-stabilized discarding sabot—tracer
API
armor-piercing incendiary
API-T
armor-piercing incendiary—tracer
AR
armor
ARNG
Army National Guard
AT
antitank
attn
attention
auto
automatic
bal
balance
BCC
ballast container compartment
BD
base detonating
BDM
bunker defeat munition
cal
caliber
comp
composite
CRR
complete round rigging
CS
chlorobenzalmalononitrile
CTN
carton
CVR
centerline vertical restraint
DA
Department of the Army
DAM
demolition attack munition
DC
District of Columbia
DD
Department of Defense
DODIC
Department of Defense Identification Code
EOD
explosive ordnance disposal
FM
field manual
ft
foot/feet
gal
gallon
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
Glossary-1
Glossary
GB
green bag
GRD
ground
HC
hexachloroethane zinc oxide powdered aluminum
HE
high explosive
HE -T
high explosive—tracer
HEAT
high-explosive antitank
HEAT-MP
high-explosive antitank-multipurpose
HEAT-MP-T
high-explosive antitank-multipurpose—tracer
HEAT-SD
high-explosive antitank-self-destruct
HEAT-T
high-explosive antitank—tracer
HEDP
high explosive dual purpose
HEI
high-explosive incendiary
HEI-T
high-explosive incendiary—tracer
HEI/TP-T
high explosive incendiary-target practice—tracer
HEI-T-SD
high-explosive incendiary—tracer self-destruct
HEP-T
high-explosive plastic tracer
HERA
high explosive rocket assisted
HQ
headquarters
ICM
improved conventional munition
in
inch
lb
pound
LCADS
low cost aerial delivery system
mg
machine gun
MDI
modernized demolition initiator
MICLIC
mine clearing line charge
mm
millimeter
mod
model
msl
missile
MT
mechanical time
MTSQ
mechanical time, superquick
NALC
Navy Ammunition Logistics Code
NATO
North Atlantic Treaty Organization
NO
number
NSN
national stock number
PD
point detonating
PETN
pentaerythritol tetranitrate
qty
quantity
RA
Regular Army
Glossary-2
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
Glossary
RAAM
remote anti-armor mine
RAAMS
remote anti-armor mine system
RAP
rocket-assisted projectile
rd
round
RQR
required
SD
self-destruct
sec
second
SLAM
selectable lightweight attack munition
TM
technical manual
TNT
trinitrotoluene
TO
technical order
TOW
tube-launched, optically tracked, wire-guided
TP-T
target practice tracer
TR
tracer
TRADOC
United States Army Training and Doctrine Command
US
United States (of America)
USAR
United States Army Reserve
VA
Virginia
w
with
WB
white bag
WHD
warhead
WP
white phosphorous
WP-T
white phosphorous-tracer
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
Glossary-3
References
AR 59-4/AFI 13-210(I), Joint Airdrop Inspection Records, Malfunction Investigations and Activity
Reporting. May 1998.
AFMAN 24-204 (I)/TM 38-250/NAVSUP PUB 505.MCOP4030.191/DLAI 4145.3, Preparing
Hazardous Materials for Military Air Shipments. October 2004.
FM 4-20.103/MCRP 4-11.3C/TO 13C7-1-11, Airdrop of Supplies and Equipment: Rigging
Containers. September 2005.
FM 4-20.112/TO 13C7-1-8, Airdrop of Supplies and Equipment: Rigging Typical Supply Loads. May
2004.
FM 4-20.117/TO 13C7-1-111, Airdrop of Supplies and Equipment: Rigging High-Mobility
Multipurpose Wheeled Vehicles. July 2005.
FM 10-515/TO 13C7-10-181, Airdrop of Supplies and Equipment: Rigging Armored
Reconnaissance/Airborne Assault Vehicle (M551). September 1984.
FM 10-500-29/TO 13C7-10-171, Airdrop of Supplies and Equipment: Rigging Heavy Antitank
Assault Weapon System (TOW). April 2000.
FM 10-534/TO 13C7-10-161, Airdrop of Supplies and Equipment: Rigging Air Defense Artillery Gun
(Vulcan). February 1985.
FM 10-550/TO 13C7-22-71, Airdrop of Supplies and Equipment: Rigging Stinger Weapons System
and Missiles. May 1984.
FM 10-552/TO 13C7-22-61, Airdrop of Supplies and Equipment: Rigging Dragon Missiles. March
1982.
FM 10-555/TO 13C7-3-401, Airdrop of Supplies and Equipment: Rigging Munitions Trailer. May
1986.
FM 10-586/TO 13C7-22-11, Airdrop of Supplies and Equipment: Rigging M22 Helicopter Armament
Subsystem Guided Missile Launcher and Missiles. April 1984
TM 10-1670-268-20&P/TO 13C7-52-22, Organizational Maintenance Manual Including Repair Parts
and Special Tools List for Type V Airdrop Platform and Dual Row Airdrop Platform,
September 2002.
TM 10-1670-275-23 & P/TO 13C5-25-2/NAVAIR 13-1-26. Unit and Intermediate Direct Support
(DS) Maintenance Manual (Including). Repair Parts and Special Tools List) for Parachute,
Cargo Type: 12-Foot Diameter, High Velocity Cargo Parachute. March 1989.
TM 10-1670-276-23&P/TO 13C5-29-2/NAVAIR 13-1-29. Unit and Intermediate Direct Support
(DS) Maintenance Manual (Including Repair Parts and Special Tools List) for Parachute,
Cargo Type: 26-Foot Diameter, High Velocity Cargo Parachute. September 1990.
TM 10-1670-278-23&P/TO 13C5-26-2/TM 01109C-23&P1/NAVAIR 13-1-27. Unit and
Intermediate Direct Support (DS) Maintenance Manual (Including Repair Parts and Special
Tools List) for Parachute, Cargo Type: 15-Foot Diameter, Cargo Extraction Parachute.
December 2004.
TM l0-1670-279-23&P/TO 13C5-27-2/NAVAIR 13-1-28. Unit and Intermediate Direct Support (DS)
Maintenance Manual
(Including Repair Parts and Special Tools List) for Parachute, Cargo
Type: 22-Foot Diameter, Cargo Extraction Parachute. August 1989.
TM 10-1670-281-23&P/ TO 13C5-32-2/ NAVAIR 13-1-32. Unit and Intermediate Direct Support
(DS) Maintenance Manual (Including Repair Parts and Special Tools List) for Parachute,
Cargo Type: 64-Foot Diameter, Model G-12D and G-12E. October 1990.
23 October 2006
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
References-1
References
TM 10-1670-282-23&P/TO 13C5-30-2/ NAVAIR 13-1-33. Unit and Intermediate Direct Support (DS)
Maintenance Manual (Including Repair Parts and Special Tools List) for Parachute, Cargo
Type: 34-Foot Diameter, Model G-14 Low-Velocity Cargo Parachute. September 1991
AFTO Form 22 Technical Order Publication Improvement Report
DA Form 2028 Recommended Changes to Publication and Blank Forms.
References-2
FM 4-20.153/MCRP 4-11.3B/TO 13C7-18-41
23 October 2006
|