SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010)

STP 9-91A14-SM-TG

Perform Winch Ground Hop Procedures on a Tracked Recovery Vehicle

091-H8T-2020

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M88A2 Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement, and

diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an

awareness of the contemporary operational environment (COE) variable and factors.

Note: If representative equipment is not available, use applicable equipment and associated references.

Standards: As a group, complete the practical exercise, "Perform Winch Ground Hop Procedures on a

Tracked Recovery Vehicle", in accordance with the applicable technical publications, practical exercise

checklist, and student supplements within the time allotted. When this practical exercise is complete, all

performance measures must be met and the system must be fully operational. An instructor will verify your

group's work upon completion of this practical exercise.

Performance Steps

1. Select and use applicable publication.

a. Identify which technical manual (TM) will be used.

b. Follow steps outlined in TM.

2. Follow prescribed safety procedures.

a. Follow procedures outlined in TM.

b. Followed safety procedures outlined in unit standing operating procedure (SOP).

3. Practice maintenance discipline.

a. Follow safety guidelines outlined in motor pool.

b. Ensure proper protective gear is used.

4. Perform ground hop procedures.

a. Ensure all leads are connected.

b. Follow steps outlined in TM.

c. Use appropriate tools for specified job.

d. Tag and label any broken or worn parts for turn-in.

5. Perform operational inspection.

a. Conduct inspection of vehicle and parts for serviceability.

b. Conduct a preventive maintenance checks and services (PMCS).

6. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet), as required.

a. Annotate any deficiencies on applicable forms.

b. Ensure forms are in accordance with DA Pamphlet (PAM) 738-751 and DA PAM 750-8.

c. Ensure paperwork gets turned-in to Unit Level Logistics System (ULLS) clerk.

7. Maintain tools and equipment.

a. Ensure all tools are accounted for.

b. Clean and store tools properly.

c. Ensure tools and equipment are cleaned and serviceable.

20 May 2010

3-185

STP 9-91A14-SM-TG

Performance Measures

NO-GO

1. Selected and used applicable publications.

——

a. Identified which technical manual (TM) was used.

b. Followed steps outlined in TM.

2. Followed prescribed safety procedures.

——

a. Followed procedures outlined in TM.

b. Followed safety procedures outlined in unit standing operating procedure

(SOP).

3. Practiced maintenance discipline.

——

a. Followed safety guidelines outlined in motor pool.

b. Ensured proper protective gear is used.

4. Performed ground hop procedures.

——

a. Ensured all leads were connected.

b. Followed steps outlined in TM.

c. Used appropriate tools for specified job.

d. Tagged and labeled any broken or worn parts for turn-in.

5. Performed operational inspection.

——

a. Conducted inspection of vehicle and parts for serviceability.

b. Conducted a preventive maintenance checks and services (PMCS).

6. Completed DA Form 5988-E, as required.

——

a. Annotated any deficiencies on applicable forms.

b. Ensured forms are in accordance with DA PAM 738-751 and DA PAM750-8.

c. Ensured paperwork gets turned-in to Unit Level Logistics System (ULLS)

clerk.

7. Maintained tools and equipment.

——

a. Ensured all tools are accounted for.

b. Cleaned and stored tools properly.

c. Ensured tools and equipment were cleaned and serviceable.

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

DA PAM 738-751

AR 385-10

DA PAM 750-8

AR 750-1

EM 0266

AR 750-43

FM 5-125

TM 9-2350-256-10

TM 9-2350-292-10

TM 9-2350-292-14&P

3-186

20 May 2010

STP 9-91A14-SM-TG

Subject Area 5: M1A2 SEP TASKS (ASI-K4 ONLY)

Perform Plumb and Synchronization Procedures

091-AK4-0079

Conditions: In a contemporary operational environment (COE) given an applicable vehicle; repair parts;

tool kit, multi-capability; test, measurement, and diagnostic equipment (TMDE); and equipment as indicated

in technical manuals (TMs); maintenance request or equipment inspection worksheet describing equipment

malfunctions; applicable technical publications; and supervision/assistance.

Standards: Perform plumb and synchronization procedures in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each MOS and skill level.) When this task is completed, the vehicle or equipment must be

fully mission-capable or maintenance actions required to be performed by other than military occupational

specialty (MOS) 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and TMDE.

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Perform Plumb and Synchronization procedures.

7. Make necessary adjustments, as required.

8. Verify procedure is performed correctly.

9. Perform a final operational test to verify Perform Plumb and Synchronization procedures are corrected

to specification.

10. Annotate corrective actions taken on DA Form 5988-E (Equipment Inspection Maintenance

Worksheet).

11. Maintain tools and equipment.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-187

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and TMDE.

——

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operated and functioned.

——

5. Inspected systems and components.

——

6. Performed Plumb and Synchronization procedures.

——

7. Made necessary adjustments, as required.

——

8. Verified procedure is performed correctly.

——

9. Performed a final operational test to verify Perform Plumb and Synchronization

——

procedures are corrected to specification.

10. Annotated corrective actions taken on DA Form 5988-E.

——

11. Maintained tools and equipment.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

DA Form 5988-E

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-188

20 May 2010

STP 9-91A14-SM-TG

Maintain Hull Mission Processor Unit (HMPU)

091-AK4-0105

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Hull Mission Processor Unit in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupation specialty (MOS) and skill level.) When this task is completed, the vehicle or

equipment must be fully mission-capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot systems and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Perform required preventive maintenance checks and services (PMCS).

11. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-189

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operated and functioned.

——

5. Inspected systems and components.

——

6. Troubleshoot systems and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Performed required preventive maintenance checks and services (PMCS).

——

11. Verified fault had been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-288-24P-1

TM 9-2350-288-24P-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-190

20 May 2010

STP 9-91A14-SM-TG

Maintain Turret Mission Processor Unit (TMPU)

091-AK4-0106

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Turret Mission Processor Unit in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupation specialty (MOS) and skill level.) When this task is completed, the vehicle or

equipment must be fully mission capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot systems and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Perform required preventive maintenance checks and services (PMCS).

11. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-191

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operated and functioned.

——

5. Inspected systems and components.

——

6. Troubleshoot systems and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Performed required preventive maintenance checks and services (PMCS).

——

11. Verified fault had been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-288-24P-1

TM 9-2350-288-24P-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-192

20 May 2010

STP 9-91A14-SM-TG

Maintain Commanders Display Unit (CDU)

091-AK4-0107

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commanders Display Unit (CDU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot systems and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Perform required preventive maintenance checks and services (PMCS).

11. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-193

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Troubleshoot systems and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Performed required preventive maintenance checks and services (PMCS).

——

11. Verified fault had been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-194

20 May 2010

STP 9-91A14-SM-TG

Maintain Gunners Control Display Panel (GCDP)

091-AK4-0108

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Gunners Control Display Panel (GCDP) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-195

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-196

20 May 2010

STP 9-91A14-SM-TG

Maintain Commanders Electronic Unit (CEU)

091-AK4-0109

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commanders Electronic Unit (CEU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotate on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-197

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-198

20 May 2010

STP 9-91A14-SM-TG

Maintain Commanders Independent Thermal Viewer/Electronics (CITV/EU)

091-AK4-0111

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commanders Independent Thermal Viewer/Electronics in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment must be fully mission capable or maintenance actions

required to be performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-199

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-200

20 May 2010

STP 9-91A14-SM-TG

Maintain Commanders Independent Thermal Viewer (CITV)

091-AK4-0112

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commander Independent Thermal Viewer (CITV) in accordance with the applicable

technical publication procedures and specifications.

(See Maintenance Allocation Chart for exact

procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When this task

is completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-201

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-1

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-202

20 May 2010

STP 9-91A14-SM-TG

Maintain Commanders Control Handle Assembly (CCHA)

091-AK4-0114

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commanders Control Handle Assembly in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and used applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-203

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-204

20 May 2010

STP 9-91A14-SM-TG

Maintain Data/Utility Bus Couplers

091-AK4-0115

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Data/Utility Bus Couplers in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupational specialty (MOS) and skill level (SL).) When this task is completed, the vehicle

or equipment must be fully mission capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Select and use applicable technical manuals (TMs).

4. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform final operational check to verify parts were replaced in accordance with TMs.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-205

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Selected and used applicable TMs.

——

4. Verified fault on DA Form 2404/DA Form 5988-E.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed final operational check to verify parts were replaced in accordance with

——

TMs.

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-206

20 May 2010

STP 9-91A14-SM-TG

Maintain Position/Navigation System (POS/NAV) Using Built In Test (BIT) and Fault Isolation Test

(FIT)

091-AK4-0116

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Position/Navigation System (POS/NAV) Using built in test (BIT) and fault isolation test

(FIT) in accordance with the applicable technical publication procedures and specifications.

(See

Maintenance Allocation Chart for exact procedures authorized for each military occupational specialty

(MOS) and skill level (SL).) When this task is completed, the vehicle or equipment must be fully

mission-capable or maintenance actions required to be performed by other than MOS 91A personnel must

be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform final operational check to verify parts were replaced in accordance with TMs.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-207

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed final operational check to verify parts were replaced in accordance with

——

TMs.

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-208

20 May 2010

STP 9-91A14-SM-TG

Maintain Circuit Breaker System on the Soldier Machine Interface (SMI)

091-AK4-0117

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Circuit Breaker on the Soldier Machine Interface (SMI) in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment must be fully mission capable or maintenance actions

required to be performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform final operational check to verify parts are replaced in accordance with TMs.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-209

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed final operational check to verify parts were replaced in accordance with

——

TMs.

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-210

20 May 2010

STP 9-91A14-SM-TG

Maintain Second Generation Common Electronics Unit (SGCEU)

091-AK4-0118

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Second Generation Common Electronics Unit (SGCEU) in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment must be fully mission capable or maintenance actions

required to be performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Remove and install components in accordance with TMs.

7. Inspect equipment and components in accordance with TMs.

8. Perform final operational check to verify parts are replaced in accordance with TMs.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-211

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Removed and installed components in accordance with TMs.

——

7. Inspected equipment and components in accordance with TMs.

——

8. Performed final operational check to verify parts were replaced in accordance with

——

TMs.

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-212

20 May 2010

STP 9-91A14-SM-TG

Maintain Hull Power Distribution Unit (HPDU)

091-AK4-0119

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Hull Power Distribution Unit (HPDU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault had been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-213

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault has been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-214

20 May 2010

STP 9-91A14-SM-TG

Maintain Remote Switching Module (RSM)

091-AK4-0120

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Remote Switching Module (RSM) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-215

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-216

20 May 2010

STP 9-91A14-SM-TG

Maintain Analog Input Module (AIM)

091-AK4-0121

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Analog Input Module in accordance with in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-217

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-218

20 May 2010

STP 9-91A14-SM-TG

Maintain Turret Power Distribution System

091-AK4-0122

Conditions: In a contemporary operational environment (COE) given an applicable vehicle; repair parts;

tool kit, multi-capability; test, measurement, and diagnostic equipment (TMDE); and equipment as indicated

in technical manuals (TMs); maintenance request or equipment inspection worksheet describing equipment

malfunctions; applicable technical publications; and supervision/assistance.

Standards: Maintain Turret Power Distribution in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupational specialty (MOS) and skill level (SL).) When this task is completed, the vehicle

or equipment must be fully mission capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Perform administrative action.

a. Select and use applicable technical manuals.

b. Select and use applicable tools and TMDE

c. Practice shop safety and maintenance discipline.

2. Maintain Turret Power Distribution System.

a. Check for loose electrical connectors, obvious damage to harnesses and leaks.

b. Ensure hydraulic pressure is at 1,500 psi and auxiliary hydraulic switch on.

3. Perform computer manual self test.

4. Inspect hydraulic hoses and hydraulic components for leaks.

5. Ensure task is performed to acceptable standards.

6. Lock main gun in travel lock.

7. Ensure tools and equipment are properly maintained.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-219

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Performed administrative action.

——

a. Selected and used applicable technical manuals.

b. Selected and used applicable tools and TMDE.

c. Practiced shop safety and maintenance discipline.

2. Maintained Turret Power Distribution System.

——

a. Checked for loose electrical connectors, obvious damage to harnesses and

leaks.

b. Ensured hydraulic pressure was at 1,500 psi and auxiliary hydraulic switch on.

3. Performed computer manual self test.

——

4. Inspected hydraulic hoses and hydraulic components for leaks.

——

5. Ensured task was performed to acceptable standards.

——

6. Locked main gun in travel lock.

——

7. Ensured tools and equipment were properly maintained.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-220

20 May 2010

STP 9-91A14-SM-TG

Maintain Drivers Integrated Display (DID)

091-AK4-0123

Conditions: In a contemporary operational environment (COE) given an applicable vehicle; repair parts;

tool kit, multi-capability; test, measurement, and diagnostic equipment (TMDE); and equipment as indicated

in technical manuals (TMs); maintenance request or equipment inspection worksheet describing equipment

malfunctions; applicable technical publications; and supervision/assistance.

Standards: Maintain Drivers Integrated Display (DID) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission-capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Perform administrative action.

a. Practice shop safety and maintenance discipline.

b. Select and use applicable TMs.

c. Select and use applicable tools and TMDE.

2. Perform initial inspection of the Drivers Integrated Display.

3. Perform panel light test.

4. Check for malfunction and warning lights.

5. Diagnose malfunction annotated on DA Form 2404 (Equipment Inspection and Maintenance

Worksheet)/DA Form 5988-E (Equipment Inspection Maintenance Worksheet).

6. Correct malfunction.

7. Verify fault has been corrected.

8. Maintain tools and equipment to prevent damage.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-221

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Performed administrative action.

——

a. Practiced shop safety and maintenance discipline.

b. Selected and used applicable TMs.

c. Selected and used applicable tools and TMDE.

2. Performed initial inspection of the Drivers Integrated Display.

——

3. Performed panel light test.

——

4. Checked for malfunction and warning lights.

——

5. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

6. Corrected malfunction.

——

7. Verified fault had been corrected.

——

8. Maintained tools and equipment to prevent damage.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-222

20 May 2010

STP 9-91A14-SM-TG

Maintain Global Positioning System (GPS)

091-AK4-0124

Conditions: In a contemporary operational environment (COE) given an applicable vehicle; repair parts;

tool kit, multi-capability; test, measurement, and diagnostic equipment (TMDE); and equipment as indicated

in technical manuals (TMs); maintenance request or equipment inspection worksheet describing equipment

malfunctions; applicable technical publications; and supervision/assistance.

Standards: Maintain Global Positioning System (GPS) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission-capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable TMs.

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-223

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-224

20 May 2010

STP 9-91A14-SM-TG

Maintain Commander's Independent Thermal Viewer (CITV) Second Generation Servo Electronics

Unit (SGSEU) (SEP)

091-AK4-0125

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commander's Independent Thermal Viewer (CITV) Second Generation Servo

Electronics Unit (SGSEU) (SEP) in accordance with the applicable technical publication procedures and

specifications.

(See Maintenance Allocation Chart for exact procedures authorized for each military

occupational specialty (MOS) and skill level (SL).) When this task is completed, the vehicle or equipment

must be fully mission-capable or maintenance actions required to be performed by other than MOS 91A

personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot systems and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Perform required preventive maintenance checks and services (PMCS).

11. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required

20 May 2010

3-225

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Troubleshoot systems and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Performed required preventive maintenance checks and services (PMCS).

——

11. Verified fault had been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-288-24-2

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-226

20 May 2010

STP 9-91A14-SM-TG

Maintain Second Generation Thermal Receiver Unit (SGTRU)

091-AK4-0126

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Second Generation Thermal Receiver Unit and replace or repair its components in

accordance with the applicable technical publication procedures and specifications.

(See Maintenance

Allocation Chart for exact procedures authorized for each military occupational specialty (MOS) and skill

level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable or maintenance

actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-227

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-228

20 May 2010

STP 9-91A14-SM-TG

Maintain Binocular Image Control Unit (BICU)

091-AK4-0127

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Binocular Image Control Unit (VCSU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-229

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-230

20 May 2010

STP 9-91A14-SM-TG

Maintain Vapor Compression System Unit (VCSU)

091-AK4-0128

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Vapor Compression System Unit (VCSU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Remove and install components in accordance with TMs.

7. Inspect equipment and components in accordance with TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-231

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Removed and installed components in accordance with TMs.

——

7. Inspected equipment and components in accordance with TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-232

20 May 2010

STP 9-91A14-SM-TG

Maintain Air Handling Unit (AHU) Thermal Management System (TMS)

091-AK4-0129

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Air Handling Unit (AHU) Thermal Receiver Unit (SGTRU) IAW the applicable

technical publication procedures and specifications.

(See Maintenance Allocation Chart for exact

procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When this task

is completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Remove and installed components in accordance with TMs.

7. Inspect equipment and components in accordance with TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Removed and installed components in accordance with TMs.

——

7. Inspected equipment and components in accordance with TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

20 May 2010

3-233

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-234

20 May 2010

STP 9-91A14-SM-TG

Maintain the Fire Suppression System

091-AK4-0132

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain the Fire Suppression System in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupational specialty (MOS) and skill level (SL).) When this task is completed, the vehicle

or equipment must be fully mission capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-235

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-236

20 May 2010

STP 9-91A14-SM-TG

Maintain Fire Control Electronics Unit (FCEU)

091-AK4-0134

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Fire Control Electronics Unit (FCEU) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-237

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-238

20 May 2010

STP 9-91A14-SM-TG

Maintain Mass Memory Unit (MMU)

091-AK4-0135

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Mass Memory Unit (MMU) in accordance with the applicable technical publication

procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for

each military occupational specialty (MOS) and skill level (SL).) When this task is completed, the vehicle

or equipment must be fully mission capable or maintenance actions required to be performed by other than

MOS 91A personnel must be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manual (TM).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-239

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

4. Selected and used applicable TM.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-240

20 May 2010

STP 9-91A14-SM-TG

Operate the Maintenance Support Device (MSD)

091-AK4-0136

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Operate the Maintenance Support Device (MSD) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Practice maintenance discipline.

2. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

3. Select and use applicable technical manual (TM).

4. Inspect equipment and components in accordance with TMs.

5. Prepare vehicle and systems for testing using Maintenance Support Device (MSD).

6. Maintain tools and equipment to prevent damage.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-241

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Verified fault on DA Form 2404/DA Form 5988-E.

——

3. Selected and used applicable technical manual (TM).

——

4. Inspected equipment and components in accordance with TMs.

——

5. Prepared vehicle and systems for testing using Maintenance Support Device

——

(MSD).

6. Maintained tools and equipment to prevent damage.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-1-1

TM 9-2350-288-20-1-2

TM 9-2350-288-20-1-3

TM 9-2350-288-20-1-4

TM 9-2350-288-20-1-5

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-242

20 May 2010

STP 9-91A14-SM-TG

Identify the M1A2 SEP Unique Components

091-AK4-0137

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Identify the M1A2 SEP Unique Components in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Practice maintenance discipline.

2. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

3. Select and use applicable technical manual (TM).

4. Inspect equipment and components in accordance with technical manuals (TMs).

5. Identify the M1A2 SEP Unique Components.

6. Maintain tools and equipment to prevent damage.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Verified fault on DA Form 2404/DA Form 5988-E.

——

3. Selected and used applicable TM.

——

4. Inspected equipment and components in accordance with TMs.

——

5. Identified the M1A2 SEP Unique Components.

——

6. Maintained tools and equipment to prevent damage.

——

20 May 2010

3-243

STP 9-91A14-SM-TG

Operate the Position/Navigation System (POS/NAV)

091-AK4-0138

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Operate the Position/Navigation System (POS/NAV) in accordance with the applicable

technical publication procedures and specifications.

(See Maintenance Allocation Chart for exact

procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When this task

is completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Operate the Position/Navigation System (POS/NAV).

7. Maintain tools and equipment to prevent damage.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Operated the Position/Navigation System (POS/NAV).

——

7. Maintained tools and equipment to prevent damage.

——

20 May 2010

3-245

STP 9-91A14-SM-TG

Operate the Second Generation Forward Looking Infrared (FLIR) System

091-AK4-0139

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Operate the Second Generation Forward Looking Infrared (FLIR) System in accordance with

the applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment must be fully mission capable or maintenance actions

required to be performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Operate the Second Generation Forward Looking Infrared (FLIR) System.

7. Maintain tools and equipment to prevent damage.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Operated the Second Generation Forward Looking Infrared (FLIR) System.

——

7. Maintained tools and equipment to prevent damage.

——

20 May 2010

3-247

STP 9-91A14-SM-TG

Operate the Thermal Management System (TMS)

091-AK4-0140

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Operate the Thermal Management System (TMS) in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Perform administrative action.

a. Select and use applicable technical manuals (TMs).

b. Select and use applicable tools and TMDE.

c. Practice shop safety and maintenance discipline.

2. Describe how systems/components operate and function.

3. Inspect systems/components.

4. Operate the Thermal Management System (TMS).

5. Ensure tools and equipment are properly maintained.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

GO NO-GO

1. Performed administrative action

——

a. Selected and used applicable technical manuals (TMs).

b. Selected and used applicable tools and TMDE

c. Practiced shop safety and maintenance discipline.

2. Described how systems/components operate and function.

——

3. Inspected systems/components.

——

4. Operated the Thermal Management System (TMS).

——

20 May 2010

3-249

STP 9-91A14-SM-TG

Maintain Commander's Independent Thermal Viewer (CITV) Sight Mode

091-AK4-0141

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain Commander's Independent Thermal Viewer (CITV) Sight Mode in accordance with

the applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment must be fully mission capable or maintenance actions

required to be performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot systems and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Perform required preventive maintenance checks and services (PMCS).

11. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

20 May 2010

3-251

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Troubleshoot systems and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Performed required preventive maintenance checks and services (PMCS).

——

11. Verified fault had been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-252

20 May 2010

STP 9-91A14-SM-TG

Operate the Second Generation Thermal Imaging System (TIS)

091-AK4-0142

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Operate the Second Generation Thermal Imaging System (TIS) in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable, or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 2404 (Equipment Inspection and Maintenance Worksheet)/DA Form 5988-E

(Equipment Inspection Maintenance Worksheet).

4. Select and use applicable technical manuals (TMs).

5. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

6. Diagnose malfunction annotated on DA Form 2404/DA Form 5988-E.

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 2404/DA Form 5988-E in accordance with The Army Maintenance Management

System (TAMMS).

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 2404/DA Form 5988-E.

——

20 May 2010

3-253

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

4. Selected and used applicable TMs.

——

5. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

6. Diagnosed malfunction annotated on DA Form 2404/DA Form 5988-E.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part was replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

11. Completed DA Form 2404/DA Form 5988-E in accordance with The Army

——

Maintenance Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-254

20 May 2010

STP 9-91A14-SM-TG

Maintain the Commanders Weapon System

091-AK4-1043

Conditions: In a contemporary operational environment (COE) given a maintenance request or equipment

inspection worksheet describing equipment malfunctions, required tools and test equipment, and with

minimum supervision.

Standards: Maintain the Commanders Weapon System in accordance with the applicable technical

publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures

authorized for each military occupational specialty (MOS) and skill level (SL).) When this task is

completed, the vehicle or equipment must be fully mission capable or maintenance actions required to be

performed by other than MOS 91A personnel must be identified.

Performance Steps

1. Select and use applicable publications.

2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).

3. Practice shop safety and maintenance discipline.

4. Describe how systems and components operate and function.

5. Inspect systems and components.

6. Troubleshoot Commanders Weapon System and components.

7. Replace defective component(s).

8. Repair defective component(s).

9. Adjust systems and components.

10. Verify fault has been corrected.

Evaluation Preparation:

WARNING

The following safety precautions must be adhered to when performing

the tasks listed in this manual: While working on electrical systems,

remove all rings, watches, and jewelry. Before working on the exhaust

system, make sure it is cool. Disconnect the negative battery cable

prior to performing any electrical system maintenance or when

performing repairs in the locality of electrical components. When

working around engines that are operating, wear hearing protection.

When removing components over 75 pounds, two personnel are

required.

Performance Measures

GO NO-GO

1. Selected and used applicable publications.

——

2. Selected and used proper tools and test, measurement, and diagnostic equipment

——

(TMDE).

3. Practiced shop safety and maintenance discipline.

——

20 May 2010

3-255

STP 9-91A14-SM-TG

Performance Measures

GO NO-GO

4. Described how systems and components operate and function.

——

5. Inspected systems and components.

——

6. Troubleshoot Commanders Weapon System and components.

——

7. Replaced defective component(s).

——

8. Repaired defective component(s).

——

9. Adjusted systems and components.

——

10. Verified fault has been corrected.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 9-2350-288-10-1

TM 9-2350-288-10-2

TM 9-2350-288-20-2-1

TM 9-2350-288-20-2-2

TM 9-2350-288-20-2-3

TM 9-2350-288-20-2-4

TM 9-2350-388-10-1

TM 9-2350-388-10-2

3-256

20 May 2010

STP 9-91A14-SM-TG

Subject Area 6: WOLVERINE (ASI-V2 ONLY)

Perform PMCS on Wolverine Bridge Assembly

091-WOL-0001

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Perform preventive maintenance checks and services (PMCS) in accordance with applicable

technical manuals (TMs). When this task is completed the equipment or end item will be fully

mission-capable or required maintenance actions to be performed by other than military occupational

specialty (MOS) 91A personnel will be identified.

Performance Steps

1. Follow prescribed safety procedures.

2. Practice maintenance discipline.

3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404

(Equipment Inspection and Maintenance Worksheet).

4. Select and use applicable technical publications.

5. Inspect equipment and components in accordance with technical manuals (TMs).

6. Perform PMCS in accordance with publications and TMs.

7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System

(TAMMS).

Performance Measures

GO NO-GO

1. Followed prescribed safety procedures.

——

2. Practiced maintenance discipline.

——

3. Verified fault on DA Form 5988-E/DA Form 2404.

——

4. Selected and used applicable technical publications.

——

5. Inspected equipment and components in accordance with TMs.

——

6. Performed PMCS in accordance with publications and TMs.

——

7. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

20 May 2010

3-257

STP 9-91A14-SM-TG

Commander's Station Familiarization

091-WOL-0002

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Perform Commander's Station Familiarization and replace or repair its components in

accordance with the applicable technical publication procedures and specifications.

(See Maintenance

Allocation Chart for exact procedures authorized for each military occupational specialty (MOS) and skill

level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable or maintenance

actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

2. Practice maintenance discipline.

3. Select and use applicable technical publications.

4. Student will have a full understanding of components and operation.

Performance Measures

GO NO-GO

1. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

2. Practiced maintenance discipline.

——

3. Selected and used applicable technical publications.

——

4. Student will have a full understanding of components and operation.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 5-5420-232-10

TM 5-5420-232-20-1

TM 5-5420-232-20-2

TM 5-5420-232-20-3

TM 5-5420-232-20-4

TM 5-5420-232-20-5

20 May 2010

3-259

STP 9-91A14-SM-TG

Launch Bridge Under Normal Operations

091-WOL-0003

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Perform Launch Bridge Under Normal Operations and replace or repair its components in

accordance with the applicable technical publication procedures and specifications.

(See Maintenance

Allocation Chart for exact procedures authorized for each military occupational specialty (MOS) and skill

level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable or maintenance

actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Inspect equipment and components in accordance with technical manuals (TMs).

4. Launch bridge under normal operations.

5. Perform operations without damage to equipment or personnel.

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Inspected equipment and components in accordance with TMs.

——

4. Launched bridge under normal operations.

——

5. Prevented damage to equipment and personnel.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 5-5420-232-10

TM 5-5420-232-20-1

TM 5-5420-232-20-2

TM 5-5420-232-20-3

TM 5-5420-232-20-4

TM 5-5420-232-20-5

3-260

20 May 2010

STP 9-91A14-SM-TG

Troubleshoot Bridge Launch System

091-WOL-0004

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Troubleshoot Bridge Launch System and replace or repair its components in accordance with

the applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404

(Equipment Inspection and Maintenance Worksheet).

3. Select and use applicable technical publications.

4. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

5. Diagnose malfunction annotated on DA Form 5988-E/DA Form 2404.

6. Inspect equipment and components in accordance with technical manuals (TMs).

7. Correct malfunction in accordance with publications and TMs.

8. Perform all final checks to verify part is replaced to specifications.

9. Verify fault has been corrected.

10. Maintain tools and equipment to prevent damage.

11. Complete DA Form 5988-E in accordance with The Army Maintenance Management System

(TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Verified fault on DA Form 5988-E/DA Form 2404.

——

3. Selected and used applicable technical publications.

——

4. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

5. Diagnosed malfunction annotated on DA Form 5988-E/DA Form 2404.

——

6. Inspected equipment and components in accordance with TMs.

——

7. Corrected malfunction in accordance with publications and TMs.

——

8. Performed all final checks to verify part is replaced to specifications.

——

9. Verified fault had been corrected.

——

10. Maintained tools and equipment to prevent damage.

——

20 May 2010

3-261

STP 9-91A14-SM-TG

Troubleshoot Launch Power Unit

091-WOL-0005

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Troubleshoot Launch Power Unit and replace or repair its components in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404

(Equipment Inspection and Maintenance Worksheet).

3. Select and use applicable technical publications.

4. Select and use correct tools and test, measurement, and diagnostic equipment (TMDE).

5. Diagnose malfunction annotated on DA Form 5988-E/DA Form 2404.

6. Remove and replace components in accordance with technical manuals (TMs).

7. Inspect equipment and components in accordance with TMs.

8. Correct malfunction in accordance with publications and TMs.

9. Perform all final checks to verify part is replaced to specifications.

10. Verify fault has been corrected.

11. Complete DA Form 5988-E in accordance with The Army Maintenance Management System

(TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Verified fault on DA Form 5988-E/DA Form 2404.

——

3. Selected and used applicable technical publications.

——

4. Selected and used correct tools and test, measurement, and diagnostic equipment

——

(TMDE).

5. Diagnosed malfunction annotated on DA Form 5988-E/DA Form 2404.

——

6. Removed and replaced components in accordance with TMs.

——

7. Inspected equipment and components in accordance with TMs.

——

8. Corrected malfunction in accordance with publications and TMs.

——

9. Performed all final checks to verify part is replaced to specifications.

——

10. Verified fault had been corrected.

——

20 May 2010

3-263

STP 9-91A14-SM-TG

Remove and Install Launch Power Unit

091-WOL-0006

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Launch Power Unit and replace or repair its components in accordance

with the applicable technical publication procedures and specifications.

(See Maintenance Allocation

Chart for exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).)

When this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions

required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace components in accordance with technical manuals (TMs).

5. Inspect equipment and components in accordance with TMs.

6. Perform all final checks to verify part is replaced to specifications.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced components in accordance with TMs.

——

5. Inspected equipment and components in accordance with TMs.

——

6. Performed all final checks to verify part is replaced to specifications.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

20 May 2010

3-265

STP 9-91A14-SM-TG

Ground Hop Launch Power Unit

091-WOL-0007

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Ground Hop Launch Power Unit and replace or repair its components in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove Launch Power Unit in accordance with technical manuals (TMs).

5. Perform preventive maintenance checks and services (PMCS) in accordance with publications and

TMs.

6. Familiar with components and ground hop procedures.

7. Perform checks to verify Launch Power Unit is replaced to specifications.

8. Maintain tools and equipment to prevent damage.

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed Launch Power Unit in accordance with TMs.

——

5. Performed preventive maintenance checks and services (PMCS) in accordance

——

with publications and TMs.

6. Familiarized with components and ground hop procedures.

——

7. Performed checks to verify Launch Power Unit was replaced to specifications.

——

8. Maintained tools and equipment to prevent damage.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

20 May 2010

3-267

STP 9-91A14-SM-TG

Remove and Install Hydraulic Module

091-WOL-0008

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Hydraulic Module and replace or repair its components in accordance with

the applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace components in accordance with technical manuals (TMs).

5. Inspect equipment and components in accordance with TMs.

6. Perform all final checks to verify part is replaced to specifications.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced components in accordance with TMs.

——

5. Inspected equipment and components in accordance with TMs.

——

6. Performed all final checks to verify part is replaced to specifications.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 5-5420-232-10

TM 5-5420-232-20-1

20 May 2010

3-269

STP 9-91A14-SM-TG

Remove and Install Charge Pump

091-WOL-0009

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Charge Pump and replace or repair its components in accordance with the

applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for

exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).) When

this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to

be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace Charge Pump in accordance with technical manuals (TMs).

5. Inspect equipment and components in accordance with TMs.

6. Perform all final checks to verify part is replaced to specifications.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced Charge Pump in accordance with TMs.

——

5. Inspected equipment and components in accordance with TMs.

——

6. Performed all final checks to verify part is replaced to specifications.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 5-5420-232-10

TM 5-5420-232-20-1

20 May 2010

3-271

STP 9-91A14-SM-TG

Remove and Install Bridge Advance Unit (Drive)

091-WOL-0010

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Bridge Advance Unit (Drive) and replace or repair its components in

accordance with the applicable technical publication procedures and specifications.

(See Maintenance

Allocation Chart for exact procedures authorized for each military occupational specialty (MOS) and skill

level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable or maintenance

actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace Bridge Advance Unit in accordance with technical manuals (TMs).

5. Perform all final checks to verify part is replaced to specifications.

6. Verify fault has been corrected.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced Bridge Advance Unit in accordance with TMs.

——

5. Performed all final checks to verify part is replaced to specifications.

——

6. Verified fault had been corrected.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

20 May 2010

3-273

STP 9-91A14-SM-TG

Remove and Install Bridge Drive Manifold

091-WOL-0011

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Bridge Drive Manifold and replace or repair its components in accordance

with the applicable technical publication procedures and specifications.

(See Maintenance Allocation

Chart for exact procedures authorized for each military occupational specialty (MOS) and skill level (SL).)

When this task is completed, the vehicle or equipment is fully mission-capable or maintenance actions

required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace Bridge Drive Manifold in accordance with technical manuals (TMs).

5. Perform all final checks to verify part is replaced to specifications.

6. Maintain tools and equipment to prevent damage.

7. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced Bridge Drive Manifold in accordance with TMs.

——

5. Performed all final checks to verify part is replaced to specifications.

——

6. Maintained tools and equipment to prevent damage.

——

7. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

TM 5-5420-232-10

TM 5-5420-232-20-1

TM 5-5420-232-20-2

TM 5-5420-232-20-3

TM 5-5420-232-20-4

TM 5-5420-232-20-5

20 May 2010

3-275

STP 9-91A14-SM-TG

Remove and Install Laying Army Hydraulic Cylinder

091-WOL-0012

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Laying Army Hydraulic Cylinder and replace or repair its components in

accordance with the applicable technical publication procedures and specifications.

(See Maintenance

Allocation Chart for exact procedures authorized for each military occupational specialty (MOS) and skill

level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable or maintenance

actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace Laying Army Hydraulic Cylinder in accordance with technical manuals (TMs).

5. Inspect equipment and components in accordance with TMs.

6. Perform all final checks to verify part is replaced to specifications.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced Laying Army Hydraulic Cylinder in accordance with TMs.

——

5. Inspected equipment and components in accordance with TMs.

——

6. Performed all final checks to verify part is replaced to specifications.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

3-276

20 May 2010

STP 9-91A14-SM-TG

Remove and Install Improved Launcher Electronics Control Unit, (ILECU)

091-WOL-0013

Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given

an M104 Armored Breacher Vehicle (Wolverine); multi-capable maintainer tool kit; special tools; test,

measurement, and diagnostic equipment (TMDE); safety equipment; required references; student

handouts; and an awareness of the contemporary operational environment (COE) variable and factors.

Standards: Remove and Install Improved Launcher Electronics Control Unit, (ILECU) and replace or repair

its components in accordance with the applicable technical publication procedures and specifications.

(See Maintenance Allocation Chart for exact procedures authorized for each military occupational specialty

(MOS) and skill level (SL).) When this task is completed, the vehicle or equipment is fully mission-capable

or maintenance actions required to be performed by other than MOS 91A personnel are identified.

Performance Steps

1. Practice maintenance discipline.

2. Select and use applicable technical publications.

3. Select and use correct tools and TMDE.

4. Remove and replace Improved Launcher Electronics Control Unit in accordance with technical

manuals (TMs).

5. Inspect equipment and components in accordance with TMs.

6. Perform all final checks to verify part is replaced to specifications.

7. Maintain tools and equipment to prevent damage.

8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet) in accordance with The

Army Maintenance Management System (TAMMS).

Performance Measures

GO NO-GO

1. Practiced maintenance discipline.

——

2. Selected and used applicable technical publications.

——

3. Selected and used correct tools and TMDE.

——

4. Removed and replaced Improved Launcher Electronics Control Unit in accordance

——

with TMs.

5. Inspected equipment and components in accordance with TMs.

——

6. Performed all final checks to verify part is replaced to specifications.

——

7. Maintained tools and equipment to prevent damage.

——

8. Completed DA Form 5988-E in accordance with The Army Maintenance

——

Management System (TAMMS).

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

3-278

20 May 2010

STP 9-91A14-SM-TG

Skill Level 3

Subject Area 7: COMMON LOGISTIC TASKS (SKILL LEVEL 3)

Manage a Maintenance Facility Safety Program

091-CLT-3001

Conditions: In a contemporary operational environment (COE) given Army regulation (AR) 190-13,

AR 220-1, AR 385-10, AR 700-138, AR 750-1, Department of the Army (DA) Pamphlet 750-8, Field Manual

(FM) 4-30.3, Technical Bulletin, TB 43-0142, and TB 43-180, a maintenance site/facility, and maintenance

personnel.

Standards: Ensure that personnel followed all safety procedures and preventable accidents were avoided.

If accidents occurred, they were properly recorded and reported in accordance with applicable references.

Performance Steps

1. Ensure all safety references were on hand.

2. Establish and document goals and requirements for a successful shop safety and accident prevention

program.

3. Brief and regularly update subordinates on shop safety program.

4. Conduct initial safety inspections.

5. Ensure initial safety concerns and violations were corrected.

6. Conduct scheduled and unscheduled safety inspections.

7. Document safety violations, report the violations as required, and conduct follow-up inspections to

ensure violations were corrected.

8. Keep necessary records of safety inspections and accident reports.

9. Ensure material safety data sheets (MSDS) are prepared and maintained as required in applicable

work areas.

Evaluation Preparation: None

Performance Measures

GO NO-GO

1. Ensured all safety references were on hand.

——

2. Established and documented goals and requirements for a successful shop safety

——

and accident prevention program.

3. Briefed and regularly updated subordinates on shop safety program.

——

4. Conducted initial safety inspections.

——

5. Ensured initial safety concerns and violations were corrected.

——

6. Conducted scheduled and unscheduled safety inspections.

——

7. Documented safety violations, reported the violations as required, and conducted

——

follow-up inspections to ensure violations were corrected.

8. Kept necessary records of safety inspections and accident reports.

——

3-280

20 May 2010

STP 9-91A14-SM-TG

Establish a Maintenance Facility Publications/Electronic Technical Manual Library

091-CLT-3002

Conditions: In a contemporary operational environment (COE) given publications, electronic technical

manuals (ETMs)/interactive electronic technical manuals (IETMs), computer with access to the World Wide

Web, storage location, local and higher headquarters publications indexes and publications procedures,

standing operating procedure (SOP), and applicable forms and references.

Standards: Ensure required publications, ETMs/IETMs are on hand or ordered, publications were

arranged and maintained properly, forms/records were properly maintained, and changes were posted in

accordance with applicable references and local procedures.

Performance Steps

1. Determine all publications required by the maintenance shop or section.

2. Review and update publications library SOP as needed.

3. Ensure that technical publications on hand or on order were the most current in accordance with DA

Pamphlet (PAM) 25-30.

4. Ensure that doctrinal, training, and organizational publications on hand or on order were the most

current in accordance with DA PAM 25-30 and local listings.

5. Ensure that administrative publications on hand or on order were the most current in accordance with

DA PAM 25-30.

6. Ensure that local and higher headquarters publications on hand or on order were the most current in

accordance with DA PAM 25-30 and local listings.

7. Prepare DA Form 4569-1-R (Security Assistance Publication Requisition Code Sheet (LRA)) in

accordance with DA PAM 25-33.

8. Prepare the required transmittal form in accordance with DA PAM 25-33.

9. Prepare DA Form 17 (Requisition for Publications and Blank Forms) and DA Form 17-1 (Requisition

for Publications and Blank Forms (Continuation Sheet)) to request local and higher headquarters

publications in accordance with DA PAM 25-33 and local or higher headquarters publications

requisitioning procedures.

10. Ensure that published changes were posted to applicable publications in accordance with DA PAM

25-40 and publications change instructions.

11. Remove obsolete, rescinded, or superseded publications from library in accordance with DA PAM

25-40 and publications change instructions.

12. Arrange publications in proper order and in a suitable location in accordance with DA PAM 25-40.

13. Label binders used for storing library publications in accordance with AR 25-400-2 and DA PAM

25-40.

14. Notify personnel to return loaned publications to the library in a timely manner in accordance with

publications library SOP.

15. Update Army Publishing Directorate (APD), local, and higher headquarters publications accounts, as

required, in accordance with DA PAM 25-33 and local or higher headquarters publications account

instructions.

3-282

20 May 2010

STP 9-91A14-SM-TG

Performance Measures

NO-GO

1. Determined all publications required by the maintenance shop or section.

——

2. Reviewed and updated publications library SOP as needed.

——

3. Ensured that technical publications on hand or on order were the most current in

——

accordance with DA PAM 25-30.

4. Ensured that doctrinal, training, and organizational publications on hand or on

——

order were the most current in accordance with DA PAM 25-30 and local listings.

5. Ensured that administrative publications on hand or on order were the most current

——

in accordance with DA PAM 25-30.

6. Ensured that local and higher headquarters publications on hand or on order were

——

the most current in accordance with DA PAM 25-30 and local listings.

7. Prepared DA Form 4569-1-R in accordance with DA PAM 25-33.

——

8. Prepared the required transmittal form in accordance with DA PAM 25-33.

——

9. Prepared DA Form 17 and DA Form 17-1 to request local and higher headquarters

——

publications in accordance with DA PAM 25-33 and local or higher headquarters

publications requisitioning procedures.

10. Ensured that published changes were posted to applicable publications in

——

accordance with DA PAM 25-40 and publications change instructions.

11. Removed obsolete, rescinded, or superseded publications from library in

——

accordance with DA PAM 25-40 and publications change instructions.

12. Arranged publications in proper order and in a suitable location in accordance with

——

DA PAM 25-40.

13. Labeled binders used for storing library publications in accordance with

——

AR 25-400-2 and DA PAM 25-40.

14. Notified personnel to return loaned publications to the library in a timely manner in

——

accordance with publications library SOP.

15. Updated Army Publishing Directorate (APD), local, and higher headquarters

——

publications accounts, as required, in accordance with DA PAM 25-33 and local or

higher headquarters publications account instructions.

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

AR 25-1

AR 25-400-2

DA Form 17

DA Form 17-1

DA Form 4569-1-R

DA PAM 25-30

DA PAM 25-33

DA PAM 25-40

20 May 2010

3-283

STP 9-91A14-SM-TG

Establish Maintenance Facilities

091-CLT-3003

Conditions: In a contemporary operational environment (COE) given a maintenance site, maintenance

personnel, applicable equipment, maintenance shop/section standing operating procedure (SOP), Field

Manual (FM) 4-30.3, and applicable references.

Standards: Set up a maintenance shop facility suitable for accomplishing necessary maintenance

functions in accordance with applicable references.

Performance Steps

1. Ensure SOP and required reference were available.

2. Identify commander's maintenance requirements for accomplishing the unit mission.

3. Set up the maintenance facility in accordance with SOP.

Evaluation Preparation: None

Performance Measures

GO NO-GO

1. Ensured SOP and required reference were available.

——

2. Identified commander's maintenance requirements for accomplishing the unit

——

mission.

3. Set up the maintenance facility in accordance with SOP.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

FM 4-30.3

3-284

20 May 2010

STP 9-91A14-SM-TG

Prepare a Maintenance Facility Standing Operating Procedure

091-CLT-3004

Conditions: In a contemporary operational environment (COE) given Field Manual (FM) 4-30.3, higher

headquarters standing operating procedure (SOP), and commander's guidance.

Standards: Prepare a draft copy of a maintenance shop/section internal or external SOP for supervisor's

review, comment, and approval in accordance with applicable references.

Performance Steps

1. Ensure applicable publications were available.

2. Ensure unit policies and commander's guidance were followed.

3. Ensure shop operation policies were adequately addressed.

4. Update the shop SOP, as required.

Evaluation Preparation: None

Performance Measures

GO NO-GO

1. Ensured applicable publications were available.

——

2. Ensured unit policies and commander's guidance were followed.

——

3. Ensured shop operation policies were adequately addressed.

——

4. Updated the shop SOP, as required.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

FM 4-30.3

20 May 2010

3-285

STP 9-91A14-SM-TG

Manage Tool Control Procedures

091-CLT-3005

Conditions: In a contemporary operational environment (COE) given Army regulation (AR) 190-13,

AR 220-1, AR 385-10, AR 700-138, AR 750-1, Department of the Army (DA) Form 2062 (Hand

Receipt/Annex Number), DA Pamphlet 710-2-1, DA Pamphlet 750-8, Field Manual (FM) 1-02, FM 4-30.3,

applicable supply catalog(s), applicable references, and hand receipt forms.

Standards: Manage tool control procedures in accordance with applicable references.

Performance Steps

1. Ensure applicable references were available.

2. Establish policies and procedures for the control of tools.

3. Ensure all DA Form 2062s were properly filled out and updated.

4. Ensure tools and equipment were inventoried in accordance with applicable references.

5. Ensure tool shortages were annotated on a shortage annex.

6. Ensure subordinates applied property accountability procedures.

Evaluation Preparation: None

Performance Measures

NO-GO

1. Ensured applicable references were available.

——

2. Established policies and procedures for the control of tools.

——

3. Ensured all DA Form 2062s were properly filled out and updated.

——

4. Ensured tools and equipment were inventoried in accordance with applicable

——

references.

5. Ensured tool shortages were annotated on a shortage annex.

——

6. Ensured subordinates applied property accountability procedures.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

AR 190-13

AR 220-1

AR 385-10

AR 700-138

AR 750-1

DA Form 2062

DA PAM 710-2-1

DA PAM 750-8

FM 1-02

FM 4-30.3

3-286

20 May 2010

STP 9-91A14-SM-TG

Manage Key Control Procedures

091-CLT-3006

Conditions: In a contemporary operational environment (COE) given Army regulation (AR) 190-13,

AR 190-51, keys, key control rosters, key boxes/cabinets, and applicable publications.

Standards: Manage key control procedures in accordance with applicable references.

Performance Steps

1. Ensure necessary publications were available.

2. Establish key control policies and procedures.

3. Establish key control access rosters.

4. Ensure personnel were aware of their responsibilities for the security and accountability of keys.

5. Ensure key control access rosters were properly maintained and adhered to.

Evaluation Preparation: None

Performance Measures

GO NO-GO

1. Ensured necessary publications were available.

——

2. Established key control policies and procedures.

——

3. Established key control access rosters.

——

4. Ensured personnel were aware of their responsibilities for the security and

——

accountability of keys.

5. Ensured key control access rosters were properly maintained and adhered to.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

AR 190-13

AR 190-51

20 May 2010

3-287

STP 9-91A14-SM-TG

Manage the TMDE Calibration Program

091-CLT-3007

Conditions: In a contemporary operational environment (COE) given Army regulation (AR) 750-43,

Technical Bulletin (TB) 43-180, test, measurement, and diagnostic equipment (TMDE), maintenance

personnel, and applicable references.

Standards: Manage the TMDE calibration program in accordance with applicable references.

Performance Steps

1. Ensure necessary publications were available.

2. Review and update TMDE computer printout list.

3. Ensure preventive maintenance checks and services (PMCS) and inventory of all TMDE and auxiliary

equipment are conducted, as required.

4. Ensure TMDE is turned in for calibration in accordance with computer printouts.

Evaluation Preparation: None

Performance Measures

GO NO-GO

1. Ensured necessary publications were available.

——

2. Reviewed and updated TMDE computer printout list.

——

3. Ensured preventive maintenance checks and services (PMCS) and inventory of all

——

TMDE and auxiliary equipment are conducted, as required.

4. Ensured TMDE was turned in for calibration in accordance with computer printouts.

——

Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier

NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was

done wrong and how to do it correctly.

References

Required

AR 750-43

TB 43-180

3-288

20 May 2010

STP 9-91A14-SM-TG

Supervise Maintenance Operations

091-CLT-3009

Conditions: In a contemporary operational environment (COE) given maintenance personnel, equipment,

maintenance facility/site, Army regulation (AR) AR 385-10, AR 600-55, AR 700-4, AR 700-138, AR 710-2,

AR 725-50, AR 735-5, AR 750-1, AR 750-43, Department of the Army (DA) Pamphlet (PAM) 25-30, DA

PAM 710-2-1, DA PAM 710-2-2, DA PAM 750-1, DA PAM 750-3, DA PAM 750-8, Field Manual (FM) 4-30.3,

standing operating procedures (SOPs), and applicable references.

Standards: Establish and maintain an effective maintenance shop operation in accordance with SOP and

applicable references.

Performance Steps

1. Ensure unit maintenance procedures are in accordance with AR 750-1, DA PAM 750-3, and local and

major Army command (MACOM) policies.

a. Review unit SOPs for maintenance.

b. Inform unit personnel of changes in policy and new policy that impacts unit SOP.

2. Provide technical assistance to unit maintenance activities.

a. Inspect unit maintenance operations.

b. Identify shortcomings.

c. Make recommendations for corrective actions.

d. Provide training in maintenance procedures.

e. Provide training and technical assistance as needed for operations under extreme heat (up to

125 degrees Fahrenheit [F]).

(1) Cooling systems. Check coolant level daily. Maintain coolant levels approximately two

inches below the radiator overflow pipe if so equipped. Check radiator air passages for

obstructions frequently. Check fan belt for proper tension. Check coolant temperature

indicators frequently for any indication of overheating.

(2) Lubrication. Make sure that lubricants used are as specified for the prevailing ambient

temperature in the current lubrication order.

(3) Fuel system. When filling the fuel tanks, allow sufficient space for fuel expansion.

(4) Batteries. Check electrolyte level frequently. Add distilled water as required to

compensate for evaporation.

(5) Engine. Kept the external surface of the engine as clean as possible.

f. Provide training and technical assistance as needed for operations in dusty or sandy areas.

(1) General. If possible, provide shelter for the equipment. Use available natural barriers to

shield the equipment from blowing dust or sand.

(2) Cleaning. Wipe dust and sand from the equipment frequently. When possible, thoroughly

washed down with clean water.

(3) Engine. Shorten the service interval for the engine air cleaner and oil filter to compensate

for intake of additional dust or dirt. Kept external surface of engine as clean as possible.

(4) Fuel systems. Drain sediment from fuel tanks, fuel strainers, and fuel filters frequently.

Was particularly careful to prevent dust or dirt from entering the fuel tank/fuel system.

Shorten the service intervals for the fuel filters appropriately.

(5) Lubrication. Lubrication intervals must be shortened appropriately. Use particular care to

keep lubricants from becoming contaminated with dust or dirt.

3. Provide maintenance management to units.

a. Review reports (Materiel Condition Status Report [MCSR] and (Unit Level Logistics

System-Ground [ULLS-G]).

b. Coordinate with higher-level maintenance activities.

c. Direct cross-leveling of maintenance assets/workloads.

d. Prioritize maintenance efforts of units.

Evaluation Preparation: None

20 May 2010

3-289

SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010) - page 3