SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010) - page 2

 

  Index      Manuals     SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010)

 

Search            copyright infringement  

 

   

 

    

 

Content      ..      1      2      3      ..

 

 

 

SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010) - page 2

 

 

STP 9-91A14-SM-TG
Correct Malfunction of the Turret Hydraulics of the M1 Series Track Vehicle
091-91A-0040
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of the Turret Hydraulics of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of turret hydraulic systems in accordance with applicable TM. When this
task is completed, the equipment or end item was fully mission-capable or required maintenance actions to
be performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2 personnel are
identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect hydraulic system components.
5. Replace turret valve.
6. Replace elevation servo mechanism fluid filter.
7. Bleed air from hydraulic system.
8. Prime the manual elevation hand pump assembly.
9. Bleed air from the manual elevation hand pump.
10. Perform a final operational test to verify hydraulic systems malfunction is corrected to specification.
11. Replace and charge main hydraulic accumulator.
12. Replace and charge manual hydraulic accumulator.
13. Annotate corrective actions taken on DA Form 5988-E.
14. Maintain tools and equipment.
3-80
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected hydraulic system components.
——
——
5. Replaced turret valve.
——
——
6. Replaced elevation servo mechanism fluid filter.
——
——
7. Bled air from hydraulic system.
——
——
8. Primed the manual elevation hand pump assembly.
——
——
9. Bled air from the manual elevation hand pump.
——
——
10. Performed a final operational test to verify hydraulic systems malfunction is
——
——
corrected to specification.
11. Replaced and charged main hydraulic accumulator.
——
——
12. Replaced and charged manual hydraulic accumulator.
——
——
13. Annotated corrective actions taken on DA Form 5988-E.
——
——
14. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
20 May 2010
3-81
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-82
20 May 2010
STP 9-91A14-SM-TG
Replace Traverse Motor Brake Assembly of the M1 Abrams Track Vehicle
091-91A-0041
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Replace
Traverse Motor Brake Assembly of the M1 Abrams Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of the traverse motor brake, servo, and manual drive assemblies in
accordance with applicable technical publications. When this task is completed, the equipment or end
item is fully mission-capable or required maintenance actions performed by other than military occupational
specialty (MOS) 91A skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Review work request.
2. Ensure task was within shop capability and authorization.
3. Ensure applicable technical publications were available.
4. Ensure proper tools, equipment, and TMDE are available to be inspected, repaired/replaced, and test
the manual drive assemblies.
5. Perform troubleshooting procedures.
6. Diagnose fault(s) and determined maintenance action is performed.
7. Identify repair parts and requisitioned, if required.
8. Ensure all safety precautions and procedures are followed.
9. Remove traverse motor brake, servo assembly.
10. Install traverse motor brake, servo assembly.
11. Critique personnel on their job performance.
12. Ensure maintenance forms are completed, as required.
13. Ensure tools, equipment, and TMDE are properly maintained.
20 May 2010
3-83
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Ensured task was within shop capability and authorization.
——
——
3. Ensured applicable technical publications were available.
——
——
4. Ensured proper tools, equipment, and TMDE are available to be inspected,
——
——
repaired/replaced, and test the manual drive assemblies.
5. Performed troubleshooting procedures.
——
——
6. Diagnosed fault(s) and determined maintenance action is performed.
——
——
7. Identified repair parts and requisitioned, if required.
——
——
8. Ensured all safety precautions and procedures are followed.
——
——
9. Removed traverse motor brake, servo assembly.
——
——
10. Installed traverse motor brake, servo assembly.
——
——
11. Critiqued personnel on their job performance.
——
——
12. Ensured maintenance forms are completed, as required.
——
——
13. Ensured tools, equipment, and TMDE are properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-84
20 May 2010
STP 9-91A14-SM-TG
Replace Manual Drive Assembly of the M1 Series Track Vehicle
091-91A-0042
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Replace
Manual Drive Assembly of the M1 Series Track Vehicle"; Technical Manual (TM) 9-2350-264-10-1; TM
9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM 9-2350-264-20-2-3; TM
9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary tools and equipment as
indicated in the TMs; test, measurement, and diagnostic equipment (TMDE); replacement parts; and
supervision/assistance.
Standards: Correct malfunction of the manual drive assemblies in accordance with applicable technical
publications. When this task is completed, the equipment or end item is fully mission-capable or required
maintenance actions performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2
personnel are identified.
Performance Steps
1. Review work request.
2. Ensure task was within shop capability and authorization.
3. Ensure applicable technical publications were available.
4. Ensure proper tools, equipment, and TMDE are available to be inspected, repaired/replaced, and test
the manual drive assemblies.
5. Perform troubleshooting procedures.
6. Diagnose fault(s) and determined maintenance action is performed.
7. Identify repair parts and requisitioned, if required.
8. Ensure all safety precautions and procedures are followed.
9. Remove traverse motor brake, servo, and manual drive assembly.
10. Install traverse motor brake, servo, and manual drive assembly.
11. Critique personnel on their job performance.
12. Ensure maintenance forms are completed, as required.
13. Ensure tools, equipment, and TMDE are properly maintained.
20 May 2010
3-85
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Ensured task was within shop capability and authorization.
——
——
3. Ensured applicable technical publications were available.
——
——
4. Ensured proper tools, equipment, and TMDE are available to be inspected,
——
——
repaired/replaced, and test the manual drive assemblies.
5. Performed troubleshooting procedures.
——
——
6. Diagnosed fault(s) and determined maintenance action is performed.
——
——
7. Identified repair parts and requisitioned, if required.
——
——
8. Ensured all safety precautions and procedures are followed.
——
——
9. Removed traverse motor brake, servo, and manual drive assembly.
——
——
10. Installed traverse motor brake, servo, and manual drive assembly.
——
——
11. Critiqued personnel on their job performance.
——
——
12. Ensured maintenance forms are completed, as required.
——
——
13. Ensured tools, equipment, and TMDE are properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-86
20 May 2010
STP 9-91A14-SM-TG
Replace Elevation Servo Assembly of the M1 Series Track Vehicle
091-91A-0043
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Replace
Elevation Servo Assembly of the M1 Series Track Vehicle"; Technical Manual (TM) 9-2350-264-10-1;
TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM 9-2350-264-20-2-3;
TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary tools and equipment as
indicated in the TMs; test, measurement, and diagnostic equipment (TMDE); replacement parts; and
supervision/assistance.
Standards: Correct malfunction of the elevation servo assembly. When this task is completed, the
equipment or end item is fully mission-capable or required maintenance actions to be performed by other
than military occupational specialty (MOS) 91A skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Review work request.
2. Ensure task is within shop capability and authorization.
3. Ensure applicable technical publications are available.
4. Ensure proper tools, equipment, and TMDE are available and inspected, repaired/replaced, and test
the elevation servo assembly.
5. Perform troubleshooting procedures.
6. Diagnose fault(s) and determined maintenance action to be performed.
7. Identify repair parts and requisitioned, if required.
8. Ensure all safety precautions and procedures are followed.
9. Remove elevation servo assembly.
10. Perform an inspection to ensure the elevation servo is fully mission-capable.
11. Install the elevation servo.
12. Ensure maintenance forms are completed, as required.
13. Ensure tools, equipment, and TMDE are properly maintained.
20 May 2010
3-87
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Ensured task is within shop capability and authorization.
——
——
3. Ensured applicable technical publications are available.
——
——
4. Ensured proper tools, equipment, and TMDE are available and inspected,
——
——
repaired/replaced, and test the elevation servo assembly.
5. Performed troubleshooting procedures.
——
——
6. Diagnosed fault(s) and determined maintenance action to be performed.
——
——
7. Identified repair parts and requisitioned, if required.
——
——
8. Ensured all safety precautions and procedures are followed.
——
——
9. Removed elevation servo assembly.
——
——
10. Performed an inspection to ensure the elevation servo is fully mission-capable.
——
——
11. Installed the elevation servo.
——
——
12. Ensured maintenance forms are completed, as required.
——
——
13. Ensured tools, equipment, and TMDE are properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-88
20 May 2010
STP 9-91A14-SM-TG
Perform Scheduled Services of the M1 Series Track Vehicle
091-91A-0044
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Perform
Scheduled Services of the M1 Series Track Vehicle"; Technical Manual (TM) 9-2350-264-10-1; TM
9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-2-1; necessary tools and equipment as
indicated in the TMs; test, measurement, and diagnostic equipment (TMDE); replacement parts; and
supervision/assistance.
Standards: Perform scheduled services on M1 Abrams tank turret in accordance with applicable technical
publications. When this task is completed, the equipment or end item is fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Perform scheduled services on the M1 Abrams tank hull.
5. Perform scheduled services on the M1 Abrams tank turret.
6. Annotate corrective actions taken on DA Form 5988-E.
7. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Performed scheduled services on the M1 Abrams tank hull.
——
——
20 May 2010
3-89
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
5. Performed scheduled services on the M1 Abrams tank turret.
——
——
6. Annotated corrective actions taken on DA Form 5988-E.
——
——
7. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-2350-264-24P-2
TM 9-2350-264-10-2
TM 9-2350-264-34-2-1
TM 9-2350-264-20-1-1
TM 9-2350-264-34-2-2
TM 9-2350-264-20-2-1
3-90
20 May 2010
STP 9-91A14-SM-TG
Maintain the Hydraulic Accumulator Manual Elevation Drive Unit on the M1 Series Track Vehicle
091-91A-0046
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Maintain the
Hydraulic Accumulator Manual Elevation Drive Unit on the M1 Series Track Vehicle"; Technical Manual
(TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: maintain the hydraulic accumulator manual elevation drive unit in accordance with applicable
technical publications. When this task is completed, the equipment or end item is fully mission-capable or
required maintenance actions performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Review work request.
2. Ensure task was within shop capability and authorization.
3. Ensure applicable technical publications were available.
4. Ensure proper tools, equipment, and TMDE are available to be inspected, repaired/replaced, and test
the manual drive assemblies.
5. Perform troubleshooting procedures.
6. Diagnose fault(s) and determined maintenance action is performed.
7. Identify repair parts and requisitioned, if required.
8. Ensure all safety precautions and procedures are followed.
9. Remove manual elevation drive unit.
10. Install manual elevation drive assembly.
11. Inspect hydraulic accumulator.
12. Purge and charge hydraulic accumulator.
13. Critique personnel on their job performance.
14. Ensure maintenance forms are completed, as required.
15. Ensure tools, equipment, and TMDE are properly maintained.
20 May 2010
3-91
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Ensured task was within shop capability and authorization.
——
——
3. Ensured applicable technical publications were available.
——
——
4. Ensured proper tools, equipment, and TMDE are available to be inspected,
——
——
repaired/replaced, and tested the manual drive assemblies.
5. Performed troubleshooting procedures.
——
——
6. Diagnosed fault(s) and determined maintenance action was performed.
——
——
7. Identified repair parts and requisitioned, if required.
——
——
8. Ensured all safety precautions and procedures are followed.
——
——
9. Removed manual elevation drive unit.
——
——
10. Installed manual elevation drive assembly.
——
——
11. Inspected hydraulic accumulator.
——
——
12. Purged and charged hydraulic accumulator.
——
——
13. Critiqued personnel on their job performance.
——
——
14. Ensured maintenance forms are completed, as required.
——
——
15. Ensured tools, equipment, and TMDE are properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
3-92
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-93
STP 9-91A14-SM-TG
Maintain Main Gun King Nut Bearing on the M1 Series Track Vehicle
091-91A-0047
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Maintain Main
Gun King Nut Bearing on the M1 Series Track Vehicle"; Technical Manual (TM) 9-2350-264-10-1;
TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM 9-2350-264-20-2-3;
TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary tools and equipment as
indicated in the TMs; test, measurement, and diagnostic equipment (TMDE); replacement parts; and
supervision/assistance.
Standards: Maintain Main Gun King Nut Bearing in accordance with applicable technical publications.
When this task is completed, the equipment or end item is fully mission-capable or required maintenance
actions to be performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2
personnel are identified.
Performance Steps
1. Review work request.
2. Ensure task is within shop capability and authorization.
3. Ensure applicable technical publications are available.
4. Ensure proper tools, equipment, and TMDE are available and inspected, repaired/replaced, and test
the elevation servo assembly.
5. Perform troubleshooting procedures.
6. Diagnose fault(s) and determined maintenance action to be performed.
7. Identify repair parts and requisitioned, if required.
8. Ensure all safety precautions and procedures are followed.
9. Remove King Nut Bearing assembly.
10. Perform an inspection to ensure the King Nut Bearing is fully mission-capable.
11. Install the King Nut Bearing assembly.
12. Ensure maintenance forms are completed, as required.
13. Ensure tools, equipment, and TMDE are properly maintained.
3-94
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Ensured task is within shop capability and authorization.
——
——
3. Ensured applicable technical publications are available.
——
——
4. Ensured proper tools, equipment, and TMDE are available and inspected,
——
——
repaired/replaced, and test the elevation servo assembly.
5. Performed troubleshooting procedures.
——
——
6. Diagnosed fault(s) and determined maintenance action to be performed.
——
——
7. Identified repair parts and requisitioned, if required.
——
——
8. Ensured all safety precautions and procedures are followed.
——
——
9. Removed King Nut Bearing assembly.
——
——
10. Performed an inspection to ensure the King Nut Bearing is fully mission-capable.
——
——
11. Installed the King Nut Bearing assembly.
——
——
12. Ensured maintenance forms are completed, as required.
——
——
13. Ensured tools, equipment, and TMDE are properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-95
STP 9-91A14-SM-TG
Subject Area 3: JOINT ASSAULT BRIDGE/ARMORED BREACHER VEHICLE (ASI-D8 ONLY)
Perform Preventive Maintenance Checks and Services (PMCS) on the ABV
091-ABV-1001
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform Preventive Maintenance Checks and Services (PMCS) on the ABV in accordance with
applicable technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
3-96
20 May 2010
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-97
STP 9-91A14-SM-TG
Maintain ABV Hull Electrical System
091-ABV-1002
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Hull Electrical System in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-98
20 May 2010
STP 9-91A14-SM-TG
Maintain ABV Hull Hydraulic System
091-ABV-1003
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Hull Hydraulic System in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with technical manuals
——
——
(TMs).
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-99
STP 9-91A14-SM-TG
Troubleshoot High Lift Adapter (HLA)
091-ABV-1004
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot High Lift Adapter (HLA) on the ABV in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-100
20 May 2010
STP 9-91A14-SM-TG
Perform Hydraulic Pressure Check on Pressure Intensifier (PIU)
091-ABV-1005
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform Hydraulic Pressure Check on Pressure Intensifier (PIU). When this task is
completed, the equipment or end item will be fully mission-capable or required maintenance actions to be
performed by other than military occupational specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with technical manuals (TMs).
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with technical manuals
——
——
(TMs).
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-101
STP 9-91A14-SM-TG
Troubleshoot Plow Power Distribution Unit (PPDU)
091-ABV-1006
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot Plow Power Distribution Unit (PPDU) in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-102
20 May 2010
STP 9-91A14-SM-TG
Perform Hydraulic Pressure Check on Hull 3-Base Manifold
091-ABV-1007
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform Hydraulic Pressure Check on Hull 3-Base Manifold in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-103
STP 9-91A14-SM-TG
Troubleshoot High Lift Adapter (HLA) Jettison Pins
091-ABV-1008
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot High Lift Adapter (HLA) Jettison Pins on the ABV in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-104
20 May 2010
STP 9-91A14-SM-TG
Perform Hydraulic Pressure Check on Front End Equipment (FEE)
091-ABV-1009
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform Hydraulic Pressure Check on Front End Equipment (FEE). When this task is
completed, the equipment or end item will be fully mission-capable or required maintenance actions to be
performed by other than military occupational specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with technical manuals (TMs).
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-105
STP 9-91A14-SM-TG
Maintain ABV Turret Hydraulic System
091-ABV-1010
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Turret Hydraulic System in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-106
20 May 2010
STP 9-91A14-SM-TG
Maintain ABV Turret Electrical System
091-ABV-1011
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Turret Electrical System in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-107
STP 9-91A14-SM-TG
Troubleshoot Turret power Distribution Unit (TPDU)
091-ABV-1012
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot Turret Power Distribution Unit (TPDU) in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-108
20 May 2010
STP 9-91A14-SM-TG
Perform Hydraulic Pressure Check on Turret 3-Base Manifold
091-ABV-1013
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform Hydraulic Pressure Check on Turret 3-Base Manifold in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with technical manuals
——
——
(TMs).
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-109
STP 9-91A14-SM-TG
Maintain ABV Turret Traversing System
091-ABV-1014
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Turret Traversing System in accordance with applicable technical manuals
(TMs). When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-110
20 May 2010
STP 9-91A14-SM-TG
Maintain ABV Integrated Viewing System (IVS)
091-ABV-1015
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain ABV Integrated Viewing System (IVS) in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-111
STP 9-91A14-SM-TG
Maintain Linear Demolition Charge System (LDCS)
091-ABV-1016
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain Lane Marking System (LMS) in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-112
20 May 2010
STP 9-91A14-SM-TG
Maintain Lane Marking System (LMS)
091-ABV-1017
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain Lane Marking System (LMS) in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-113
STP 9-91A14-SM-TG
Troubleshoot Lane Marking System Unit (LMSCU)
091-ABV-1018
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot Lane Marking System Unit (LMSCU) in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with technical manuals
——
——
(TMs).
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-114
20 May 2010
STP 9-91A14-SM-TG
Maintain Lane Marking System (LMS) Compressor Assemblies
091-ABV-1019
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain Lane Marking System (LMS) Compressor Assemblies in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-115
STP 9-91A14-SM-TG
Perform Preventive Maintenance Checks and Services (PMCS) on the JAB and Bridge Launcher
System
091-JAB-1001
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Perform preventive maintenance checks and services (PMCS) in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-116
20 May 2010
STP 9-91A14-SM-TG
Utilize Embedded Diagnostic System to Maintain JAB
091-JAB-1002
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Utilize Embedded Diagnostic System to Maintain JAB in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-117
STP 9-91A14-SM-TG
Maintain JAB Embedded Diagnostic System (EDS)
091-JAB-1003
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain JAB Embedded Diagnostic System (EDS) in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-118
20 May 2010
STP 9-91A14-SM-TG
Troubleshoot Vehicle using Embedded Diagnostic (ED) System
091-JAB-1004
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot Vehicle using Embedded Diagnostic (ED) System in accordance with applicable
technical manuals (TMs). When this task is completed, the equipment or end item will be fully
mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-119
STP 9-91A14-SM-TG
Troubleshoot JAB Hull System
091-JAB-1005
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot JAB Hull System in accordance with applicable technical manuals (TMs). When
this task is completed, the equipment or end item will be fully mission-capable or required maintenance
actions to be performed by other than military occupational specialty (MOS) 91A personnel will be
identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-120
20 May 2010
STP 9-91A14-SM-TG
Maintain JAB Hull Electrical System
091-JAB-1006
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot JAB Hull Electrical System in accordance with applicable technical manuals
(TMs). When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-121
STP 9-91A14-SM-TG
Maintain JAB Hull Hydraulic System
091-JAB-1007
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Troubleshoot JAB Hull Hydraulic System in accordance with applicable technical manuals
(TMs). When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-122
20 May 2010
STP 9-91A14-SM-TG
Maintain JAB Bridge Launcher System
091-JAB-1008
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain JAB Bridge Launcher System in accordance with applicable technical manuals (TMs).
When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-123
STP 9-91A14-SM-TG
Maintain JAB Hydraulic Bridge Launcher System
091-JAB-1009
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain JAB Hydraulic Bridge Launcher System in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-124
20 May 2010
STP 9-91A14-SM-TG
Maintain the JAB Turbine Hydraulic Pumping Unit (HPU) and Diesel Hydraulic PUMP (DHP)
091-JAB-1010
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain the JAB Turbine Hydraulic Pumping Unit (HPU) and Diesel Hydraulic PUMP (DHP) in
accordance with applicable technical manuals (TMs). When this task is completed, the equipment or end
item will be fully mission-capable or required maintenance actions to be performed by other than military
occupational specialty (MOS) 91A personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-125
STP 9-91A14-SM-TG
Maintain the JAB Bridge and Bridge Launch System
091-JAB-1011
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain the JAB Bridge and Bridge Launch System in accordance with applicable technical
manuals (TMs). When this task is completed, the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
personnel will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-126
20 May 2010
STP 9-91A14-SM-TG
Maintain JAB Launcher Electrical System
091-JAB-1012
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain JAB Launcher Electrical System in accordance with applicable technical manuals
(TMs). When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
20 May 2010
3-127
STP 9-91A14-SM-TG
Maintain JAB Visual Enhancement System
091-JAB-1013
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
a Joint Assault Bridge and launcher; multi-capable maintainer tool kit; special tools; test, measurement, and
diagnostic equipment (TMDE); safety equipment; required references; student handouts; and an
awareness of the operational environment (OE) variable and factors.
Standards: Maintain JAB Visual Enhancement System in accordance with applicable technical manuals
(TMs). When this task is completed, the equipment or end item will be fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A personnel
will be identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E (Equipment Inspection Maintenance Worksheet)/DA Form 2404
(Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable technical publications.
5. Inspect equipment and components in accordance with TMs.
6. Perform PMCS in accordance with publications and TMs.
7. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable technical publications.
——
——
5. Inspected equipment and components in accordance with TMs.
——
——
6. Performed PMCS in accordance with publications and TMs.
——
——
7. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what
was done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
DA Form 5988-E
3-128
20 May 2010
STP 9-91A14-SM-TG
Subject Area 4: RECOVERY (ASI-H8 ONLY)
Locate a Recovery Site
091-H8C-2001
Conditions: In a contemporary operational environment (COE) given a representative recovery vehicle,
required materials, multi-capability tool kit, and applicable references.
Standards: Locate a recovery site to within 10 meters and identified primary and alternate recovery routes
determining distance for both with no greater than a 10 percent error.
Performance Steps
1. Select and use applicable publications.
2. Identify terrain features.
3. Identify map symbols and colors.
4. Locate site using military grid reference system.
5. Calculate distance.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Identified terrain features.
——
——
3. Identified map symbols and colors.
——
——
4. Located site using military grid reference system.
——
——
5. Calculated distance.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
20 May 2010
3-129
STP 9-91A14-SM-TG
References
Required
Related
FM 21-31
TC 43-35
FM 3-25.26
TM 9-2320-279-10-1
TM 9-2320-279-10-2
TM 9-2320-279-20-1
TM 9-2320-279-20-2
TM 9-2320-279-20-3
3-130
20 May 2010
STP 9-91A14-SM-TG
Determine Recovery Methods
091-H8C-2002
Conditions: In a contemporary operational environment (COE) given a representative recovery vehicle,
required materials, general mechanic's tool kit, and applicable references including Field Manual (FM)
5-125, Training Circular (TC) 43-35, and recovery vehicle Technical Manual (TM) 9-2320-279-10-1, TM
9-2320-279-10-2, TM 9-2320-279-20-1, TM 9-2320-279-20-2, and TM 9-2320-279-20-3.
Standards: Determine recovery methods, source of effort, and mechanical advantage needed in
accordance with references.
Performance Steps
1. Select and use applicable publications.
2. Reconnoiter area.
3. Estimate situation.
4. Calculate ratios.
5. Obtain resistance.
6. Verify solution.
7. Erect rigging.
8. Recheck rigging.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Reconnoitered area.
——
——
3. Estimated situation.
——
——
4. Calculated ratios.
——
——
5. Obtained resistance.
——
——
6. Verified solution.
——
——
20 May 2010
3-131
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
7. Erected rigging.
——
——
8. Rechecked rigging.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
FM 5-125
TM 9-2320-272-10
TC 43-35
TM 9-2350-256-10
TM 9-2320-279-10-1
TM 9-2320-279-10-2
TM 9-2320-279-20-1
TM 9-2320-279-20-2
TM 9-2320-279-20-3
3-132
20 May 2010
STP 9-91A14-SM-TG
Operate Tactical Communications Equipment
091-H8C-2003
Conditions: In a contemporary operational environment (COE) given a representative wheel vehicle
(M984 series), required materials, general mechanic's tool kit, Technical Manual (TM) 11-5820-890-10-3,
TM 9-2320-279-10-1, TM 9-2320-279-10-2, TM 9-2320-279-20-1, TM 9-2320-279-20-2, and TM
9-2320-279-20-3, and other applicable publications.
Standards: Stated the procedures for installing, operating, and using correct radio procedures for clear,
concise, and secure communications in accordance with the appropriate publications.
Performance Steps
1. Select and use applicable publications.
2. Prepare communications equipment for operation.
3. Send tactical communications.
4. Receive tactical communications
5. Shut down tactical communications operation.
6. Follow prescribed safety procedures.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Prepared communications equipment for operation.
——
——
3. Sent tactical communications.
——
——
4. Received tactical communications.
——
——
5. Shut down tactical communications operation.
——
——
6. Followed prescribed safety procedures.
——
——
20 May 2010
3-133
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
TM 11-5820-890-10-3
TC 43-35
TM 9-2320-279-10-1
TM 11-5820-401-10-1
TM 9-2320-279-10-2
TM 11-5820-401-10-2
TM 9-2320-279-20-1
TM 11-5820-401-10-4
TM 9-2320-279-20-2
TM 11-5830-340-12
TM 9-2320-279-20-3
3-134
20 May 2010
STP 9-91A14-SM-TG
Operate Metal Cutting Equipment
091-H8C-2004
Conditions: In a contemporary operational environment (COE) given a representative recovery vehicle,
required materials, general mechanic's tool kit, Training Circular (TC) 9-237, and applicable recovery
vehicle Technical Manual (TM) 9-2320-279-10-1, TM 9-2320-279-10-2, TM 9-2320-279-20-1, TM
9-2320-279-20-2, and TM 9-2320-279-20-3.
Standards: Stated the procedures for installing, operating, and using correct radio procedures for clear,
concise, and secure communications in accordance with the appropriate publications.
Performance Steps
1. Select and use applicable publications.
2. Determine the method to cut metal.
3. Prepare metal cutting equipment, as required.
4. Cut metal.
5. Secure metal cutting equipment.
6. Follow prescribed safety procedures.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Determined the method to cut metal.
——
——
3. Prepared metal cutting equipment, as required.
——
——
4. Cut metal.
——
——
5. Secured metal cutting equipment.
——
——
6. Followed prescribed safety procedures.
——
——
20 May 2010
3-135
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
TC 9-237
AR 385-10
TM 9-2320-279-10-1
AR 750-1
TM 9-2320-279-10-2
DA PAM 750-8
TM 9-2320-279-20-1
TC 43-35
TM 9-2320-279-20-2
TM 9-2320-366-10-1
TM 9-2320-279-20-3
TM 9-2320-366-10-2
TM 9-2350-256-10
TM 9-243
3-136
20 May 2010
STP 9-91A14-SM-TG
Maintain Recovery Vehicle Weapons
091-H8T-2001
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Department of the Army (DA) Form 2404
(Equipment Inspection and Maintenance Worksheet), DA Form 5988-E (Equipment Inspection
Maintenance Worksheet), Technical Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1, TM
9-2350-256-20-2, TM 9-2350-256-24P-1, TM 9-2350-256-24P-2, and other applicable publications.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Maintain the M88 series vehicle weapons in accordance with the preventive maintenance
checks and services (PMCS) table and procedures and specifications of the applicable TM. When this task
is complete, the vehicle is fully mission capable or maintenance actions required to be performed by other
than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publication.
a. Ensure appropriate TM is used.
b. Ensure steps are followed outlined in the TM.
2. Use proper safety methods.
a. Ensure proper safety methods are followed.
b. Follow prescribed safety precautions outlined in TM.
3. Disassemble machine gun.
a. Ensure machine gun is on safe.
b. Lock bolt to the rear
c. Ensure weapon is clear.
d. Follow steps outline in the TM.
4. Check for broken or missing parts.
a. Separate machine gun components.
b. Visually inspect each machine gun component for damage.
c. Tag and label any parts for turn-in.
d. Ensure DA Form 2404 or DA Form 5988-E has been filled out.
5. Ensure all parts are cleaned and lubricated.
a. Clean each machine gun component.
b. Follow lubrication procedures outline in the TM.
6. Assemble machine gun.
a. Locate and identify machine gun components to be assembled.
b. Follow assemble procedures outline within the TM.
7. Set head-space and timing.
a. Ensure proper tools are used.
b. Follow procedures outlined in the TM for setting head-space and timing.
c. Verify head-space and timing settings.
8. Inspect machine gun mount for missing, cracks, or broken parts.
a. Follow proper procedures outlined in the TM.
b. Tag and label any broken parts for turn-in.
c. Ensure part has been requisitioned on proper paperwork.
20 May 2010
3-137
STP 9-91A14-SM-TG
Performance Steps
9. Ensure launcher tubes are free of rust, dirt and corrosion.
a. Follow proper procedures outlined in the TM.
b. Remove any rust, dirt and corrosion found within or on launcher tubes.
10. Ensure that grenade launcher wiring harness connectors are connected.
a. Locate and identify grenade launcher wiring harness connectors.
b. Check grenade launcher wiring harness for proper connections.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches and jewelry. Before working on the
exhaust system, make sure it is cool. Disconnect the negative battery
cable prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TMs were used.
b. Ensured steps are followed outlined in the TM.
2. Used proper safety methods.
——
——
a. Ensured proper safety methods are followed.
b. Followed prescribed safety precautions outlined in TM.
3. Disassembled machine gun.
——
——
a. Ensured machine gun was on safe.
b. Locked bolt to the rear.
c. Ensured weapon was cleared.
d. Followed steps outlined in the TM.
4. Checked for broken or missing parts.
——
——
a. Separated machine gun components.
b. Visually inspected each machine gun component for damage.
c. Tagged and labeled any parts for turn-in.
d. Ensured DA Form 2404 and DA Form 5988-E have been filled out.
5. Ensured all parts were cleaned and lubricated.
——
——
a. Cleaned each machine gun component.
b. Followed lubrication procedures outlined in the TM.
6. Assembled machine gun.
——
——
a. Located and identified machine gun components to be assembled.
b. Followed assembly procedures outline within the TM.
3-138
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
7. Set head-space and timing.
——
——
a. Ensured proper tools were used.
b. Followed procedures outlined in the TM.
c. Verified head-space and timing settings.
8. Inspected machine gun mount for missing, cracked, or broken parts.
——
——
a. Followed proper procedures outlined in the TM.
b. Tagged and labeled any broken parts for turn-in.
c. Ensured part had been requisitioned on proper paperwork.
9. Ensured launcher tubes were free of rust, dirt, and corrosion.
——
——
a. Followed proper procedures outlined in the TM.
b. Removed any rust, dirt, and corrosion found within or on launcher tubes.
10. Ensured that grenade launcher wiring harness connectors were connected.
——
——
a. Located and identified grenade launcher wiring harness connections.
b. Checked grenade launcher wiring harness for proper connections.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
AR 385-10
DA Form 5988-E
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
20 May 2010
3-139
STP 9-91A14-SM-TG
Complete Preventive Maintenance Checks and Services on a Tracked Recovery Vehicle
091-H8T-2002
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Department of the Army (DA) Form 2404
(Equipment Inspection and Maintenance Worksheet), DA Form 5988-E (Equipment Inspection
Maintenance Worksheet), DA Pamphlet 750-8, Technical Manual (TM) 9-2350-256-10, TM
9-2350-256-20-1, TM 9-2350-256-20-2, TM 9-2350-256-24P-1, TM 9-2350-256-24P-2, and TM
9-2350-292-10, and other applicable forms and publications.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Inspect the M88 series vehicle in accordance with the preventive maintenance checks and
services (PMCS) table of the applicable TM and record deficiencies on DA Form 2404 or DA Form 5988-E
in accordance with DA Pamphlet 750-8. When this task is complete, the vehicle is fully mission capable or
maintenance actions required to be performed by other than H8 skill levels (SLs) 1/2 personnel has been
identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow steps outlined in appropriate publication.
2. Select and use proper tools and test, measurement, and diagnostic equipment (TMDE).
a. Identify appropriate tools in basic issue items (BII).
b. Ensure appropriate tools are serviceable.
3. Describe operation of vehicle systems and subsystems.
a. Locate appropriate systems and subsystems operations in the TM.
b. Read and follow systems and subsystems maintenance operating guidance outlined in TM.
4. Determine readiness of system components.
a. Ensure components are at operating temperature.
b. Verify equipment operating gauges and instruments.
5. Identify deficiencies and shortcomings.
a. Follow steps outlined in TM pertaining to deficiencies.
b. Record deficiencies and shortcomings on DA Form 2404 or DA Form 5988-E.
6. Correct shortcomings identified as operator maintenance.
a. Take appropriate measures to repair all deficiencies and shortcomings that need to be repaired.
b. Notify supervisor if fault is found beyond operator level of maintenance.
7. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
3-140
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Followed steps outlined in TM.
2. Selected and used proper tools and TMDE.
——
——
a. Identified appropriate tools in BII.
b. Ensured appropriate tools were serviceable.
3. Described operation of vehicle systems and subsystems.
——
——
a. Located appropriate systems and subsystems operations in the TM.
b. Read and followed systems and subsystems maintenance operating
guidance in TM.
4. Determined readiness of system components.
——
——
a. Ensured components were at operating temperature.
b. Verified equipment operating gauges and instruments.
5. Identified deficiencies and shortcomings.
——
——
a. Followed steps outlined in the technical manual to pertaining to deficiencies.
b. Recorded deficiencies and shortcomings using DA Form 2404 or DA Form
5988-E.
6. Corrected shortcomings identified as operator maintenance.
——
——
a. Took appropriate measures to repair all deficiencies and shortcomings that
needed to be repaired.
b. Notified supervisor if fault was found beyond operator level of maintenance.
7. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
20 May 2010
3-141
STP 9-91A14-SM-TG
References
Required
Related
DA Form 2404
AR 385-10
DA Form 5988-E
AR 750-1
DA PAM 750-8
AR 750-43
TM 9-2350-256-10
TM 9-243
TM 9-2350-256-20-1
TM 9-8000
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
TM 9-2350-292-10
3-142
20 May 2010
STP 9-91A14-SM-TG
Use Basic Issue Items Related to Tracked Recovery Vehicle
091-H8T-2003
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Technical Manual (TM) 9-2350-256-10, TM
9-2350-256-20-1, TM 9-2350-256-20-2, TM 9-2350-256-24P-1, TM 9-2350-256-24P-2, TM 9-2350-292-10,
and other applicable forms and publications.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Remove, clean, and store the recovery related components of end item (COEI) and basic issue
items (BII) in accordance with the procedures in TM 9-2350-256-10 and TM 9-2350-292-10. When this task
is complete, the vehicle is fully mission capable or maintenance actions required to be performed by other
than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow steps outlined in appropriate publication.
2. Inventory and determine serviceability of BII.
a. Identify appropriate tools in BII.
b. Inspect BII for serviceability.
3. Repair BII, as required.
a. Follow steps outlined in TM pertaining to serviceability of BII.
b. Tag and label unserviceable BII for turn-in.
4. Replace BII, as required.
a. Follow directions outlined in publication on replacement of BII.
b. Ensure appropriate BII has been ordered on applicable forms.
5. Use BII, as required.
a. Select appropriate BII pertaining to job.
b. Follow procedures in TM.
6. Service BII, as required.
a. Refer to TM for servicing data.
b. Verify servicing information in TM.
7. Store BII properly.
a. Ensure all tools are accounted for.
b. Ensure tools are cleaned before storing.
8. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
20 May 2010
3-143
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriated TM was used.
b. Followed steps outlined in appropriate publication.
2. Inventoried and determined serviceability of BII.
——
——
a. Identified appropriate tools in BII.
b. Inspected BII for serviceability.
3. Repaired BII, as required.
——
——
a. Followed steps outlined in TM pertaining to serviceability of BII.
b. Tagged and labeled unserviceable BII for turn-in.
4. Replaced BII, as required.
——
——
a. Followed directions outlined in publication on replacement of BII.
b. Ensured appropriate BII was ordered on applicable forms.
5. Used BII, as required.
——
——
a. Selected appropriate BII pertaining to job.
b. Followed procedures in TM.
6. Serviced BII, as required.
——
——
a. Referred to TM for servicing data.
b. Verified servicing information in TM.
7. Stored BII properly.
——
——
a. Ensured all tools were accounted for.
b. Ensured all tools were cleaned before storing.
8. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
3-144
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-256-10
AR 750-1
TM 9-2350-256-20-1
AR 750-43
TM 9-2350-256-20-2
DA Form 2404
TM 9-2350-256-24P-1
DA Form 5988-E
TM 9-2350-256-24P-2
TM 9-8000
TM 9-2350-292-10
20 May 2010
3-145
STP 9-91A14-SM-TG
Drive Tracked Recovery Vehicle
091-H8T-2004
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, The Army Maintenance Management System
(TAMMS) forms, Technical Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1, TM 9-2350-256-20-2, TM
9-2350-256-24P-1, TM 9-2350-256-24P-2, and other applicable publications.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Negotiate obstacles in forward and reverse gears without stalling, jerking, getting stuck, or
causing damage to the vehicle and while obeying all safety procedures, traffic regulations, and hand
signals. When this task is complete, the vehicle is fully mission capable or maintenance actions required
to be performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Verify procedures while performing tracked recovery operations.
2. Perform preventive maintenance checks and services (PMCS).
a. Identify what TM to use.
b. Follow procedures outlined in TM.
c. Annotate any deficiencies on appropriate forms.
d. Ensure forms are in accordance with DA Pamphlet (PAM) 738-751 and DA PAM 750-8.
3. Start engine.
a. Ensure vehicle parking brake is engaged.
b. Check instrument panel to ensure gauges are operational.
c. Follow start up procedures outlined in TM.
4. Place vehicle in motion.
a. Disengage parking brake.
b. Follow safety procedures outlined in motor pool.
c. Ensure ground guides are used, if required.
5. Drive vehicle, maintaining proper engine speed when descending and ascending grades.
a. Follow vehicle operating instructions, while maintaining proper engine speed, when descending
and ascending grades.
b. Verify vehicle operating instructions, while maintaining proper engine speed, when descending
and ascending grades.
6. Drive vehicle in reverse.
a. Ensure ground guide is used.
b. Maintain proper speed while vehicle is in reverse.
7. Stop vehicle.
a. Follow safety guidelines outlined in motor pool.
b. Carefully bring the vehicle to a stop, while adhering to safe driving habits.
8. Parking vehicle.
a. Ensure proper ground guides are used.
b. Ensure there is enough clearance from other vehicles.
9. Stop engine (normal and emergency procedures).
a. Follow guidelines outlined in TM for proper stopping procedures.
b. Ensure parking brake is engaged.
3-146
20 May 2010
STP 9-91A14-SM-TG
Performance Steps
c. Ensure vehicle is chock blocked.
d. Perform an after-operations PMCS.
10. Complete TAMMS forms, as required.
a. Annotate any deficiencies on appropriate forms.
b. Ensure parts are ordered, if needed.
c. Turn forms into Unit Level Logistics System (ULLS) clerk.
11. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Followed procedures outlined within TM.
b. Verified procedures while performing tracked recovery operations.
2. Performed preventive maintenance checks and services (PMCS).
——
——
a. Identified what TM was used.
b. Followed procedures outlined within TM.
c. Annotated any deficiencies on appropriate forms.
d. Ensured forms are in accordance with DA PAM 738-751 and DA PAM 750-8.
3. Started engine.
——
——
a. Ensured vehicle parking brake was engaged.
b. Checked instrument panel to ensure gauges were operational.
c. Followed start up procedures outlined in TM.
4. Placed vehicle in motion.
——
——
a. Disengaged parking brake.
b. Followed safety procedures outlined in motor pool.
c. Ensured ground guide was used, if required.
5. Drove vehicle, maintaining proper engine speed when descending and ascending
——
——
grades.
a. Followed vehicle operating instructions, while maintaining proper engine
speed, when descending and ascending grades.
b. Verified vehicle operating instructions, while maintaining proper engine
speed, when descending and ascending grades.
20 May 2010
3-147
STP 9-91A14-SM-TG
Performance Measures
GO
NO-GO
6. Drove vehicle in reverse.
——
——
a. Ensured ground guide was used.
b. Maintained proper speed while vehicle was in reverse.
7. Stopped vehicle.
——
——
a. Followed safety guidelines outlined in motor pool.
b. Carefully brought vehicle to a stop, while adhering to safe driving habits.
8. Parked vehicle.
——
——
a. Ensured proper ground guides were used.
b. Ensured there was enough clearance from other vehicles.
9. Stopped engine (normal and emergency procedures).
——
——
a. Followed guidelines outlined in TM for proper stopping procedures.
b. Ensured parking brake was engaged.
c. Ensured vehicle was chock blocked.
d. Performed an after-operations PMCS.
10. Completed TAMMS forms, as required.
——
——
a. Annotated any deficiencies on appropriate forms.
b. Ensured parts were ordered, if needed.
c. Turned forms into Unit Level Logistics System (ULLS) clerk.
11. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit standing operating procedure
(SOP).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA PAM 738-751
AR 385-10
DA PAM 750-8
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
3-148
20 May 2010
STP 9-91A14-SM-TG
Operate Auxiliary Power Unit
091-H8T-2005
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Technical Manual (TM) 9-2350-256-10, TM
9-2350-292-10, TM 9-2350-256-20-1, TM 9-2350-256-20-2, and other applicable publications.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Operate the Auxiliary Power Unit (APU) and basic issue items (BII) powered by the APU in
accordance with the procedures in TM 9-2350-256-10 and TM 9-2350-292-10 without damage to the
equipment. When this task is complete, the vehicle is fully mission capable or maintenance actions required
to be performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow steps outlined in TM pertaining to APU procedures.
2. Start APU.
a. Follow APU start up procedures outlined in TM.
b. Operate APU in accordance with applicable specifications.
c. Ensure BII is operable without damage to APU.
3. Actuate generator switch to charge batteries.
a. Follow procedures outlined in TM.
b. Verify procedures while actuated generator switch to charge batteries.
4. Engage hydraulic control levers to start refuel/defuel pump.
a. Follow procedures outlined within TM.
b. Verify procedures while performing refueling/refueling operations.
5. Connect and operate hydraulic equipment.
a. Ensure all steps are followed in accordance with TM.
b. Verify connection while operating hydraulic equipment.
6. Shut down APU.
a. Ensure shutdown procedures are in accordance with TM.
b. Perform preventive maintenance checks and services (PMCS) while applying shutdown
procedures.
7. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
20 May 2010
3-149
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Followed steps outline in TM pertaining to APU procedures.
2. Started APU.
——
——
a. Followed APU start up procedures outlined within TM.
b. Operated APU in accordance with applicable specifications.
c. Ensured BII was operable without damage to APU.
3. Actuated generator switch to charge batteries.
——
——
a. Followed procedures outlined in TM.
b. Verified procedures while actuated generator switch to charge batteries.
4. Engaged hydraulic control levers to start refuel/defuel pump.
——
——
a. Followed procedures outlined within TM.
b. Verified procedures while engaging hydraulic control lever to start
refuel/defuel operations.
5. Connected and operated hydraulic equipment.
——
——
a. Followed procedures outlined within TM.
b. Verified connection while operating hydraulic equipment.
6. Shut down APU.
——
——
a. Followed APU shutdown procedures outlined within TM.
b. Verified procedures while performing APU shutdown task.
7. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 385-10
AR 750-1
AR 750-43
3-150
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-292-10
20 May 2010
3-151
STP 9-91A14-SM-TG
Operate the Boom and Hoist Winch on a Tracked Recovery Vehicle
091-H8T-2006
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, and applicable publications including
Technical Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1, TM 9-2350-256-20-2, TM 9-2350-256-34,
and TM 9-2350-292-10.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Rig and operate the boom on the M88A1/M88A2 tracked recovery vehicle in accordance with
the procedures in TM 9-2350-256-10 or TM 9-2350-292-10. When this task is complete, the vehicle is fully
mission capable or maintenance actions required to be performed by other than H8 skill levels (SLs) 1/2
personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Verify procedures while performing Boom, Hoist, and Winch operations.
2. Prepare vehicle for use of hydraulic equipment.
a. Ensure appropriate basic issue items (BII) is used.
b. Follow procedures outlined in TM.
c. Disconnect any lines and fittings connecting equipment.
d. Ensure appropriate equipment is hooked up.
3. Operate boom.
a. Follow steps outlined in TM.
b. Check equipment for any leaks.
4. Operate hoist winch.
a. Ensure all connections are hooked up properly.
b. Verify procedures while performing hoist and winch operations.
c. Check equipment for any leaks.
5. Secure hydraulic equipment, as required.
a. Ensure all equipment is properly secured.
b. Ensure area is cleaned in accordance with Environmental Protection Agency (EPA) regulations.
6. Follow prescribed safety procedures.
a. Follow safety procedures outlined in motor pool.
b. Ensure to follow all safety guidance outlined with standing operating procedure (SOP).
3-152
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Verified procedures while performing Boom, Hoist, and Winch operations.
2. Prepared vehicle for use of hydraulic equipment.
——
——
a. Ensured appropriate BII was used.
b. Followed procedures outlined within TM.
c. Disconnected any lines and fittings connecting equipment.
d. Ensured appropriate equipment is hooked up.
3. Operated boom.
——
——
a. Followed steps outlined in TM.
b. Checked equipment for any leaks.
4. Operated hoist winch.
——
——
a. Ensured all connections are hooked up properly.
b. Verified procedures while performing hoist and winch operations.
c. Checked equipment for any leaks.
5. Secured hydraulic equipment, as required.
——
——
a. Ensured all equipment was properly secured.
b. Ensured area is cleaned in accordance with EPA regulations.
6. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in motor pool.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 385-10
AR 750-1
AR 750-43
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-292-10
20 May 2010
3-153
STP 9-91A14-SM-TG
Operate the Spade on a Tracked Recovery Vehicle
091-H8T-2007
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Department of the Army (DA) Form 2404
(Equipment Inspection and Maintenance Worksheet), DA Form 5988-E (Equipment Inspection
Maintenance Worksheet), Technical Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1,
TM 9-2350-256-20-2, TM 9-2350-256-24P-1, TM 9-2350-256-24P-2, TM 9-2350-292-10, and related
references.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Operate the spade in accordance with applicable technical publication procedures and
specifications without injury to personnel or damage to equipment. When this task is completed, the
vehicle is fully mission capable or maintenance actions required to be performed by other than H8 skill
levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow steps identified in TM for job performance.
2. Prepare vehicle for use of hydraulic equipment.
a. Follow steps outlined in TM.
b. Perform a before-operations preventive maintenance checks and services (PMCS).
3. Operate spade.
a. Follow safety precautions outlined in TM.
b. Check equipment for leaks.
c. Perform an after-operations PMCS.
d. Annotate any deficiencies on appropriate DA Form 2404 and DA Form 5988-E, if needed.
4. Secure hydraulic equipment, as required.
a. Ensure all attachments and basic issue items (BII) are secured properly.
b. Ensure area is cleaned of any Environmental Protection Agency (EPA) violations.
5. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
3-154
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM is used.
b. Followed steps outlined in TM for job performance.
2. Prepared vehicle for use of hydraulic equipment.
——
——
a. Followed steps outlined in TM.
b. Performed a before-operations PMCS.
3. Operated spade.
——
——
a. Followed safety precautions outlined in TM.
b. Checked equipment for leaks.
c. Performed an after-operations PMCS.
d. Annotated any deficiencies on appropriate DA Form 2404 and DA Form
5988-E, if needed.
4. Secured hydraulic equipment, as required.
——
——
a. Ensured all attachments and BII are secured properly.
b. Ensured area was cleaned of any EPA violations.
5. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 385-10
AR 750-1
AR 750-43
DA Form 2404
DA Form 5988-E
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
TM 9-2350-292-10
20 May 2010
3-155
STP 9-91A14-SM-TG
Operate the Winches on a Tracked Recovery Vehicle
091-H8T-2008
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, and required publications including Technical
Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1, TM 9-2350-256-20-2, TM 9-2350-256-24P-1, TM
9-2350-256-24P-2, TM 9-2350-256-34, and TM 9-2350-292-10.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Operate the main winch and auxiliary winch in accordance with the procedures in TM
9-2350-256-10 and TM 9-2350-292-10 without causing damage to the equipment or injury to personnel.
When this task is complete, the vehicle is fully mission capable or maintenance actions required to be
performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow procedures outlined in TM for job performance.
2. Prepare vehicle for use of hydraulic equipment.
a. Ensure basic issue items (BII) and test, measurement, and diagnostic equipment (TMDE) are
available.
b. Perform a before-operations preventive maintenance checks and services (PMCS).
3. Operate main winch.
a. Follow steps outlined in TM.
b. Check equipment for any leaks.
c. Annotate any deficiencies on appropriate forms, if needed.
4. Secure hydraulic equipment, as required.
a. Ensure all attachments and equipment are cleaned and stored properly.
b. Perform an after-operations PMCS.
5. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety procedures outlined in unit standing operating procedure (SOP).
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
3-156
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Followed procedures outlined in TM for job performance.
2. Prepared vehicle for use of hydraulic equipment.
——
——
a. Ensured BII and TMDE were available.
b. Performed a before-operations PMCS.
3. Operated main winch.
——
——
a. Followed steps outlined in TM.
b. Checked equipment for any leaks.
c. Annotated any deficiencies on appropriate forms, if needed.
4. Secured hydraulic equipment, as required.
——
——
a. Ensured all attachments and equipment were cleaned and stored properly.
b. Performed an after-operations PMCS.
5. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 385-10
AR 750-1
AR 750-43
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
TM 9-2350-292-10
20 May 2010
3-157
STP 9-91A14-SM-TG
Recover a Mired Tracked Vehicle
091-H8T-2009
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, and applicable publications including
Technical Manual (TM) 9-2350-256-10, TM 9-2350-256-20-1, TM 9-2350-256-20-2, TM 9-2350-256-24P-1,
TM 9-2350-256-24P-2, and TM 9-2350-256-34.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Accomplish task in accordance with applicable TM's procedures and specifications. All safety
precautions were observed. When this task is complete, the vehicle is fully mission capable or maintenance
actions required to be performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Identify which TM will be used.
b. Followed steps outlined in TM.
2. Determine method of rigging.
a. Follow steps outlined in TM.
b. Ensure rigging lines are not defected.
3. Attach cable to the mired vehicle.
a. Follow safety precautions outlined in TM.
b. Ensure all observing personnel are at least one cable length away, opposite angle of pull.
4. Prepare recovery vehicle for recovery operations.
a. Ensure parking brake is not engaged.
b. Inspect tackle and equipment before recovery operation starts.
5. Establish communications between vehicles.
a. Observe ground guide while operating recovery equipment.
b. Ensure proper speed limit is followed.
6. Recover mired vehicle ensuring that all safety practices were followed.
a. Ensure proper safety equipment is used.
b. Ensure proper hand signals are used during recovery.
7. Secure recovery equipment.
a. Disconnect and stow rigging equipment.
b. Perform after-operations preventive maintenance checks and services (PMCS).
c. Annotate any deficiencies on appropriate forms, if needed.
3-158
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which TM was used.
b. Followed steps outlined in TM.
2. Determined method of rigging.
——
——
a. Followed steps outlined in TM.
b. Ensured rigging lines were not defected.
3. Attached cables to the mired vehicle.
——
——
a. Followed safety precautions outlined in TM.
b. Ensured all observing personnel were at least one cable length away,
opposite angle of pull.
4. Prepared recovery vehicle for recovery operations.
——
——
a. Ensured parking brake was not engaged.
b. Inspected tackle and equipment before recovery operation starts.
5. Established communications between vehicles.
——
——
a. Observed ground guide while operating recovery equipment.
b. Ensured proper speed limit was followed.
6. Recovered mired vehicle ensuring that all safety practices were followed.
——
——
a. Ensured proper safety equipment was used.
b. Ensured proper hands signals were used during recovery.
7. Secured recovery equipment.
——
——
a. Disconnected and stowed rigging equipment.
b. Performed after-operations PMCS.
c. Annotated any deficiencies on appropriate forms, if needed.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 385-10
AR 750-10
AR 750-43
20 May 2010
3-159
STP 9-91A14-SM-TG
References
Required
Related
DA PAM 750-8
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
3-160
20 May 2010
STP 9-91A14-SM-TG
Recover an Overturned Tracked Vehicle
091-H8T-2010
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Technical Manual (TM) 9-2350-256-10, TM
9-2350-256-20-1, and related references.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Recover the vehicle from the overturned position in accordance with applicable technical
publications. When this task is complete, the vehicle is fully mission capable or maintenance actions
required to be performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Follow steps outlined in TM.
2. Position recovery vehicle.
a. Follow vehicle operating instructions outlined in TM.
b. Carefully position recovery vehicle while adhering to safe driving habits.
3. Attach cable to the overturned vehicle.
a. Ensure proper safety equipment is used.
b. Inspect cable for broken strands or kinks.
c. Remove any loops from cable while it is slack.
d. Ensure shackles and pins are properly secured.
4. Prepare recover vehicle for recovery operations.
a. Ensure recovery vehicle is upright.
b. Set up recovery controls.
5. Establish communication with ground guide.
a. Use proper hand signals.
b. Keep contact with ground guide at all times.
6. Recover overturned vehicle, ensuring that all safety practices are followed.
a. Ensure all observing personnel are out of area of projection.
b. Follow overturned vehicle operating instructions outlined in TM.
7. Secure recovery equipment.
a. Follow procedures outlined in TM.
b. Disconnect and stow rigging equipment.
c. Perform after-operations preventive maintenance checks and services (PMCS).
d. Annotate any deficiencies on appropriate forms, if needed.
20 May 2010
3-161
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Followed steps outlined in TM.
2. Positioned recovery vehicle.
——
——
a. Followed vehicle operating instruction outlined in TM.
b. Carefully positioned recovery vehicle while adhering to safe driving habits.
3. Attached cables to the overturned vehicle.
——
——
a. Ensured proper safety equipment is used.
b. Inspected cable for broken stands or kinks.
c. Removed any loops from cable while it is slack.
d. Ensured shackles and pins are properly secured.
4. Prepared recovery vehicle for recovery operations.
——
——
a. Ensured recovery vehicle is upright.
b. Set up recovery controls.
5. Established communications with ground guide.
——
——
a. Used proper hand signals.
b. Kept contact with ground guide at all times.
6. Recovered overturned vehicle, ensuring that all safety practices were followed.
——
——
a. Ensured all observing personnel are out of area of projection.
b. Followed overturned vehicle operating instructions outlined in TM.
7. Secured recovery equipment.
——
——
a. Followed procedures outlined in TM.
b. Disconnected and stowed rigging equipment.
c. Performed after-operations PMCS.
d. Annotated any deficiencies on appropriate forms, if needed.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
3-162
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-256-10
AR 385-10
TM 9-2350-256-20-1
AR 750-1
AR 750-10
AR 750-43
20 May 2010
3-163
STP 9-91A14-SM-TG
Tow a Tracked Vehicle on Improved/Highway Surface
091-H8T-2011
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Field Manual (FM) 5-125, Technical Manual
(TM) 9-2350-256-10, TM 9-2350-256-20-1, TM 9-2350-256-24P-1, TM 9-2350-256-24P-2, and related
references.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Lift and tow a disabled vehicle in accordance with applicable technical publications,
procedures, and specifications. When this task is complete, the vehicle is fully mission capable or
maintenance actions required to be performed by other than H8 skill levels (SLs) 1/2 personnel has been
identified.
Performance Steps
1. Select and use applicable publications.
a. Ensured appropriate TM is used.
b. Followed steps outlined in TM.
2. Determine method for towing.
a. Follow steps outlined in TM.
b. Ensure appropriate basic issue items (BII) and test, measurement, and diagnostic equipment
(TMDE) are used.
3. Prepare vehicle for towing.
a. Ensure parking brake is disengaged.
b. Estimate the situation to determine resistance.
c. Compute the total resistance.
4. Hook up vehicle for towing.
a. Ensure appropriate hook up devices are used.
b. Verify procedures while securing hook attachment to disabled vehicle.
5. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Ensure safety equipment is used.
6. Establish communication between vehicles.
a. Observe ground guide while operating vehicle and equipment.
b. Ensure proper speed limit is followed.
7. Tow vehicle to predetermined site.
a. Maintain proper speed limit.
b. Ensure emergency equipment and tow lights are operable.
8. Disconnect vehicle.
a. Ensure parking brake is engaged.
b. Disconnect emergency equipment and tow lights.
c. Store equipment.
d. Conduct after-operations preventive maintenance checks and services (PMCS).
e. Annotate any deficiencies on appropriate paperwork, if needed.
3-164
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Followed steps outlined in TM.
2. Determined method for towing.
——
——
a. Followed steps outlined in TM.
b. Ensured appropriate BII and TMDE were used.
3. Prepared vehicle for towing.
——
——
a. Ensured parking brake was disengaged.
b. Estimated the situation to determine resistance.
4. Hooked up vehicle for towing.
——
——
a. Ensured appropriate hook up devices were used.
b. Verified procedures while securing hook attachment to disabled vehicle.
5. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Ensured safety equipment was used.
6. Established communications between vehicles.
——
——
a. Observed ground guide while operating vehicle and equipment.
b. Ensure proper speed limit was followed.
7. Towed vehicle to predetermined site.
——
——
a. Maintained proper speed limit.
b. Ensured emergency equipment and tow lights were operable.
8. Disconnected vehicle.
——
——
a. Ensured parking brake was engaged.
b. Disconnected emergency equipment and tow lights.
c. Stored equipment.
d. Conducted after-operations PMCS.
e. Annotated any deficiencies on appropriate paperwork, if needed.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
20 May 2010
3-165
STP 9-91A14-SM-TG
References
Required
Related
FM 5-125
AR 385-10
TM 9-2350-256-10
AR 750-1
TM 9-2350-256-20-1
AR 750-43
TM 9-2350-256-24P-1
TM 9-243
TM 9-2350-256-24P-2
TM 9-8000
3-166
20 May 2010
STP 9-91A14-SM-TG
Tow of a Tracked Vehicle Cross Country
091-H8T-2012
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Field Manual (FM) 5-125, Technical Manual
(TM) 9-2350-256-10, and related references.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Tow a disabled vehicle to a predetermined location without causing damage to the equipment
or injury to personnel in accordance with applicable publications. When this task is complete, the vehicle is
fully mission capable or maintenance actions required to be performed by other than H8 skill levels (SLs)
1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Ensure appropriate TM is used.
b. Verify procedures while performing cross country towing of a tracked vehicle.
2. Follow prescribed safety procedures.
a. Follow prescribed safety procedures outlined in TM.
b. Follow safety guidelines for specified terrain.
3. Position recovery vehicle.
a. Ensure ground guide is used.
b. Carefully position recovery vehicle while adhering to safe driving habits.
4. Prepare recovery vehicle for towing.
a. Ensure parking brake is not engaged.
b. Follow vehicle towing operating instructions outlined in TM.
c. Use applicable shackles and recovery equipment.
d. Estimate the situation and load resistance.
5. Prepare recovery vehicle for towing operation.
a. Ensure appropriate hook up devices are used.
b. Follow vehicle towing operating instructions outlined in TM.
6. Attach towing bar to disabled vehicle.
a. Inspect towing equipment for missing parts.
b. Ensure appropriate tow equipment is used.
7. Operate boom.
a. Ensure all personnel are out of area of projection.
b. Follow vehicle boom operating instructions outlined in TM.
8. Tow disabled vehicle.
a. Ensure no objects are under or around vehicle.
b. Maintain appropriate speed while towing vehicle.
9. Disconnect towed vehicle.
a. Ensure all safety precautions are used when disconnecting tow equipment.
b. Ensure parking brake is engaged on vehicle.
c. Conduct after-operations preventive maintenance checks and services (PMCS).
d. Annotate any deficiencies on appropriate paperwork, if needed.
20 May 2010
3-167
STP 9-91A14-SM-TG
Performance Steps
10. Secure recovery equipment.
a. Store all recovery equipment in appropriate basic issue items (BII) storage.
b. Ensure all equipment is cleaned before storing.
c. Ensure all recovery equipment is accounted for.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Ensured appropriate TM was used.
b. Verified procedures while performing cross country towing of a tracked
vehicle.
2. Followed prescribed safety procedures.
——
——
a. Followed prescribed safety procedures outlined in TM.
b. Followed safety guidelines for specific terrain.
3. Positioned recovery vehicle.
——
——
a. Ensure ground guide was used.
b. Carefully positioned recovery vehicle while adhering to safe driving habits.
4. Prepared vehicle for towing.
——
——
a. Ensured parking brake was not engaged.
b. Followed vehicle towing operating instructions outlined in TM.
c. Used applicable shackles and recovery equipment.
d. Estimated the situation and load resistance.
5. Prepared recovery vehicle for towing operation.
——
——
a. Ensured appropriate hook up devices were used.
b. Followed vehicle towing operating instructions outlined in TM.
6. Attached towing bar to disabled vehicle.
——
——
a. Inspected towing equipment for missing parts.
b. Ensured appropriate tow equipment was used.
7. Operated boom.
——
——
a. Ensured all personnel were out of area of projection.
b. Followed vehicle boom operating instructions outlined in TM.
3-168
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
8. Towed disabled vehicle.
——
——
a. Ensured no objects were under or around vehicle.
b. Maintained appropriate speed while towing vehicle.
9. Disconnected towed vehicle.
——
——
a. Ensured all safety precautions were used when disconnecting tow equipment.
b. Ensured parking brake was engaged on vehicle.
c. Conducted after-operations PMCS.
d. Annotated any deficiencies on appropriate paperwork, if needed.
10. Secured recovery equipment.
——
——
a. Stored all equipment in appropriate BII storage.
b. Ensured all equipment was cleaned before storing.
c. Ensured all recovery equipment was accounted for.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
FM 5-125
AR 385-10
TM 9-2350-256-10
AR 750-1
AR 750-43
TM 9-243
TM 9-8000
20 May 2010
3-169
STP 9-91A14-SM-TG
Complete Field Expedient Recovery on a Tracked Vehicle
091-H8T-2013
Conditions: In a contemporary operational environment (COE) given a representative tracked vehicle
(M88 series), required materials, general mechanic's tool kit, Technical Manual (TM) 9-2350-256-10, TM
9-2350-256-20-1, and related references.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: Recover the vehicle using self/field expedient procedures in accordance with applicable
technical publications. When this task is complete, the vehicle is fully mission capable or maintenance
actions required to be performed by other than H8 skill levels (SLs) 1/2 personnel has been identified.
Performance Steps
1. Select and use applicable publications.
a. Identify which TM is used.
b. Follow steps outlined in TM.
2. Determine method of field expedient recovery.
a. Diagnose vehicle malfunction to determine action to be performed.
b. Verify proper tools are available to perform action.
3. Prepare vehicle for field expedient recovery, as required.
a. Ensure all safety precautions are used.
b. Verify procedures while preparing vehicle for field expedient recovery.
4. Perform vehicle field expedient recovery.
a. Obtain proper resistance.
b. Check all rigging equipment.
c. Coordinate with maintenance support team (MST) to provide technical assistance.
d. Ensure all maintenance forms are filled out.
5. Secure recovery equipment.
a. Disconnect recovery equipment.
b. Verify procedures while securing recovery equipment.
c. Ensure all recovery equipment is accounted for.
6. Follow prescribed safety procedures.
a. Follow all safety procedures outlined in TM.
b. Follow all safety procedures outlined in unit standing operating procedure (SOP).
3-170
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which TM was used.
b. Followed steps outlined in TM.
2. Determined method of field expedient recovery.
——
——
a. Diagnosed vehicle malfunction to determine action to be performed.
b. Verified proper tools were available to perform action.
3. Prepared vehicle for field expedient recovery, as required.
——
——
a. Ensured all safety precautions were used.
b. Verified procedures while preparing vehicle for field expedient recovery.
4. Performed vehicle field expedient recovery.
——
——
a. Obtained proper resistance.
b. Checked all rigging equipment.
c. Coordinated with MST to provide technical assistance.
d. Ensured all maintenance forms were filled out.
5. Secured recovery equipment.
——
——
a. Disconnect recovery equipment.
b. Verified procedures while securing recovery equipment.
c. Ensured all recovery equipment was accounted for.
6. Followed prescribed safety procedures.
——
——
a. Followed all safety precautions outlined in TM.
b. Followed all safety procedures outlined in unit SOP.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
TM 9-2350-256-10
AR 385-10
TM 9-2350-256-20-1
AR 750-1
AR 750-43
20 May 2010
3-171
STP 9-91A14-SM-TG
Maintain Charging System on a Tracked Recovery Vehicle
091-H8T-2014
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88 Series Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement,
and diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Charging System on a Tracked
Recovery Vehicle", in accordance with the applicable technical publications, practical exercise checklist,
and student supplements within the time allotted. When this practical exercise is complete, all
performance measures must be met and the system must be fully operational. An instructor will verify your
group's work upon completion of this practical exercise.
Performance Steps
1. Select and use applicable publications.
a. Identify which technical manual to be used.
b. Follow steps outlined in technical manual for charging system.
2. Inventory and determine serviceability of BII and TMDE.
a. Ensure all tools are serviceable.
b. Identify appropriate tools in BII.
3. Check all electrical connections.
a. Follow procedures outlined in technical manual.
b. Replace any worn parts.
4. Perform diagnostic procedures on charging system.
a. Conduct a risk assessment.
b. Follow steps outlined in technical manual.
5. Follow prescribed safety procedures.
a. Follow safety precautions outlined in technical manual.
b. Follow safety guidelines outlined in unit SOP.
6. Complete TAMMS forms as required.
a. Annotate any deficiencies on appropriate forms.
b. Ensure forms are in accordance with DA Pamphlet 738-751 and DA Pamphlet 750-8.
7. Maintain tools and equipment.
a. Ensure all BII is accounted for.
b. Ensure all tools are cleaned and stored properly.
3-172
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which technical manual was used.
b. Followed steps outlined in technical manual for charging system.
2. Inventoried and determined serviceability of BII and TMDE.
——
——
a. Ensured all tools were serviceable.
b. Identified appropriate tools in BII.
3. Checked all electrical connections.
——
——
a. Followed procedures outlined in technical manual.
b. Replaced any worn parts.
4. Performed diagnostic procedures on charging system.
——
——
a. Conducted a risk assessment.
b. Followed steps outlined in technical manual.
5. Followed prescribed safety procedures.
——
——
a. Followed safety precautions outlined in technical manual.
b. Followed safety guidelines outlined in unit SOP.
6. Completed TAMMS forms as required.
——
——
a. Annotated any deficiencies on appropriate forms.
b. Ensured forms were in accordance with DA Pamphlet 738-751 and DA
Pamphlet 750-8.
7. Maintained tools and equipment.
——
——
a. Ensured BII was accounted for.
b. Ensured all tools were cleaned and stored properly.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA PAM 738-751
AR 385-10
DA PAM 750-8
AR 750-1
EM 0266
AR 750-43
20 May 2010
3-173
STP 9-91A14-SM-TG
References
Required
Related
FM 5-125
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
TM 9-2350-292-10
TM 9-2350-292-14&P
3-174
20 May 2010
STP 9-91A14-SM-TG
Maintain Starting System on a Tracked Recovery Vehicle
091-H8T-2015
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88 Series Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement,
and diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Starting System on a Tracked Recovery
Vehicle", in accordance with the applicable technical publications, practical exercise checklist, and student
supplements within the time allotted. When this practical exercise is complete, all performance measures
must be met and the system must be fully operational. An instructor will verify your group's work upon
completion of this practical exercise.
Performance Steps
1. Select and use applicable publications.
a. Identify appropriate technical manual (TM).
b. Follow steps outlined in TM.
2. Inventory and determine appropriate basic issue items (BII) and TMDE.
a. Ensure all tools are serviceable.
b. Identify appropriate tools in BII.
3. Check all electrical connections.
a. Follow procedures outlined in TM.
b. Replace any worn parts.
4. Perform diagnostic procedures for starting system.
a. Follow procedures outlined in TM.
b. Adjust alternator, if needed.
c. Adjust belt tension, if needed.
5. Follow prescribed safety procedures.
a. Follow safety procedures outlined in TM.
b. Follow safety guidelines outlined in unit standing operating procedure (SOP).
6. Complete all applicable forms.
a. Annotate any deficiencies on appropriate forms.
b. Ensure forms are in accordance with DA Pamphlet 738-751 and DA Pamphlet 750-8.
7. Maintain tool and equipment.
a. Ensure all BII is accounted for.
b. Ensure all tools are cleaned and serviceable.
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified appropriate technical manual (TM).
b. Followed steps outlined in TM.
2. Inventoried and determined appropriate basic issue items (BII) and TMDE.
——
——
a. Ensured all tools were serviceable.
b. Identified appropriate tools in BII.
20 May 2010
3-175
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
3. Checked all electrical connections.
——
——
a. Followed procedures outlined in TM.
b. Replaced any worn parts.
4. Performed diagnostic procedures for starting system
——
——
a. Followed procedures outlined in TM.
b. Adjusted alternator, if required.
c. Adjusted belt tension, if needed.
5. Followed prescribed safety procedures.
——
——
a. Followed safety procedures outlined in TM.
b. Followed safety guidelines outlined in unit standing operating procedure
(SOP).
6. Completed all applicable forms.
——
——
a. Annotated any deficiencies on appropriate forms.
b. Ensured forms are in accordance with DA Pamphlet 738-751 and DA
Pamphlet 750-8.
7. Maintained tools and equipment.
——
——
a. Ensured all BII was accounted for.
b. Ensured all tools were cleaned and serviceable.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA PAM 738-751
AR 385-10
DA PAM 750-8
AR 750-1
EM 0266
AR 750-43
FM 5-125
TM 9-2350-256-10
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-256-24P-1
TM 9-2350-256-24P-2
TM 9-2350-292-10
TM 9-2350-292-14&P
3-176
20 May 2010
STP 9-91A14-SM-TG
Maintain Auxiliary Power Unit (APU) on a Tracked Recovery Vehicle
091-H8T-2016
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88 Series Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement,
and diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Auxiliary Power Unit (APU) on a Tracked
Recovery Vehicle", in accordance with the applicable technical publications, practical exercise checklist,
and student supplements within the time allotted. When this practical exercise is complete, all
performance measures must be met and the system must be fully operational. An instructor will verify your
group's work upon completion of this practical exercise.
Performance Steps
1. Select and use applicable publications.
a. Identify which technical manual will be used.
b. Follow steps outlined in technical manual.
2. Inventory BII and TMDE.
a. Ensure all tools are serviceable.
b. Identify which tools will be used.
3. Practice maintenance discipline.
a. Follow safety guidelines for motor-pool.
b. Ensure proper safety equipment is utilized.
4. Inspect vehicle APU components.
a. Ensure there is no visible damage to components.
b. Follow procedures outlined in technical manual.
5. Follow prescribed safety procedures.
a. Follow safety precautions outlined in technical manual.
b. Follow safety guidelines outlined in unit SOP.
6. Clean vehicle APU mounting components.
a. Clean debris that will cause damage to vehicle and system.
b. Inspect for damage to gaskets or seals.
7. Replace APU components, as required.
a. Use appropriate tools.
b. Disconnect electrical connections.
c. Tag and label parts for turn-in, if required.
8. Perform final operational check to verify system is operational.
a. Follow steps outlined in technical manual.
b. Annotate any deficiencies on applicable forms, if needed.
9. Maintain tools and equipment.
a. Ensure all BII is accounted for.
b. Ensure all tools are cleaned and stored properly.
20 May 2010
3-177
STP 9-91A14-SM-TG
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which technical manual was used.
b. Followed steps outlined in technical manual.
2. Inventoried BII and TMDE.
——
——
a. Ensured all tools were serviceable.
b. Identified which tools were used.
3. Practiced maintenance discipline.
——
——
a. Followed safety guidelines for motor-pool.
b. Ensured proper safety equipment is utilized.
4. Inspected vehicle APU components.
——
——
a. Ensured there was no visible damage to components.
b. Followed procedures outlined in technical manual.
5. Followed prescribed safety procedures.
——
——
a. Followed safety precautions outlined in technical manual.
b. Followed safety guidelines outlined in unit SOP.
6. Cleaned vehicle APU mounting components.
——
——
a. Cleaned debris that will cause damage to vehicle and system.
b. Inspected for damage to gaskets and seals.
7. Replaced APU components, if required.
——
——
a. Used appropriate tools.
b. Disconnected electrical connections.
c. Tagged and labeled parts for turn-in, if required.
8. Performed final operational check to verify system was operational.
——
——
a. Followed steps outlined in technical manual.
b. Annotated any deficiencies on applicable forms, if needed.
9. Maintained tools and equipment.
——
——
a. Ensured BII was accounted for.
b. Ensured all tools are cleaned and stored properly.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
EM 0266
AR 385-10
FM 5-125
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-292-10
TM 9-2350-292-14&P
3-178
20 May 2010
STP 9-91A14-SM-TG
Maintain Brake System on a Tracked Recovery Vehicle
091-H8T-2017
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88 Series Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement,
and diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Brake System on a Tracked Recovery
Vehicle", in accordance with the applicable technical publications, practical exercise checklist, and student
supplements within the time allotted. When this practical exercise is complete, all performance measures
must be met and the system must be fully operational. An instructor will verify your group's work upon
completion of this practical exercise.
Performance Steps
1. Select and use applicable publications.
a. Identify which technical manual will be used.
b. Follow steps outlined in technical manual.
2. Select and use correct tools and TMDE.
a. Identify applicable tools in BII.
b. Ensure tools are serviceable.
3. Follow prescribed safety procedures.
a. Follow procedures outlined in technical manual.
b. Follow safety precautions outlined in unit SOP.
4. Practice maintenance discipline.
a. Follow safety guidelines outlined in motor-pool.
b. Ensure proper safety equipment is used, if needed.
5. Inspect vehicle brake system components.
a. Follow steps outlined in technical manual.
b. Check vehicle for leaks.
c. Check for missing components.
6. Replace vehicle brake system components, if required.
a. Remove damage components, if required.
b. Tag and label part for turn-in.
7. Perform final operational inspection.
a. Ensure parts are tightened to specification.
b. Verify fault was correct, if required.
c. Take vehicle on a road test and perform PMCS.
8. Maintain tools and equipment.
a. Ensure all tools are accounted for.
b. Ensure all tools and equipment are cleaned properly.
9. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet), if required.
a. Annotate faults corrected on applicable forms.
b. Ensure paperwork gets turned-in to ULLS clerk.
20 May 2010
3-179
STP 9-91A14-SM-TG
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which technical manual was used.
b. Followed steps outlined in technical manual.
2. Selected and used correct tools and TMDE.
——
——
a. Identified applicable tools in BII.
b. Ensured tools were serviceable.
3. Followed prescribed safety procedures.
——
——
a. Followed procedures outlined in technical manual.
b. Followed safety precautions outlined in unit SOP.
4. Practiced maintenance discipline.
——
——
a. Followed safety guidelines outlined in motor-pool.
b. Ensured proper safety equipment was used, if needed.
5. Inspected vehicle brake system components.
——
——
a. Followed steps outlined in technical manual.
b. Checked vehicle for leaks.
c. Checked for missing components.
6. Replaced vehicle brake system components, if required.
——
——
a. Removed damaged components, if required.
b. Tagged and labeled parts for turn-in.
7. Performed final operational inspection.
——
——
a. Ensured parts are tightened to specification.
b. Verified fault was corrected, if required.
c. Took vehicle on a road test and performed PMCS.
8. Maintained tools and equipment.
——
——
a. Ensured all tools were accounted for.
b. Ensured all tools and equipment were cleaned properly.
9. Completed DA Form 5988-E, if required.
——
——
a. Annotated faults corrected on applicable forms.
b. Ensured paperwork got turned-in to ULLS clerk.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
EM 0266
AR 385-10
FM 5-125
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-292-10
TM 9-2350-292-14&P
3-180
20 May 2010
STP 9-91A14-SM-TG
Maintain Nose Cone Assembly on a Tracked Recovery Vehicle
091-H8T-2018
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88 Series Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement,
and diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Nose Cone Assembly on a Tracked
Recovery Vehicle", in accordance with the applicable technical publications, practical exercise checklist,
and student supplements within the time allotted. When this practical exercise is complete, all
performance measures must be met and the system must be fully operational. An instructor will verify your
group's work upon completion of this practical exercise.
Performance Steps
1. Select and use applicable publications.
a. Identify which technical manual will be used.
b. Follow steps outlined in technical manual.
2. Select and use correct tools and TMDE.
a. Identify applicable tools in BII.
b. Ensure serviceability of tools.
3. Follow prescribed safety procedures
a. Follow procedures outlined in technical manual.
b. Follow safety precautions outlined in unit SOP.
4. Practice maintenance discipline.
a. Follow safety guidelines outlined in motor-pool.
b. Ensure proper safety equipment is used.
5. Inspect vehicle Nose crane assembly and winch,
a. Follow steps outlined in technical manual.
b. Check assembly for serviceability.
c. Check for missing components.
6. Replace nose crane assembly components, if required.
a. Follow steps outlined in technical manual.
b. Use proper tools for specified job.
c. Remove any damaged components.
d. Tag and label broken components for turn-in, if needed.
7. Perform operational inspection.
a. Ensure parts are tightened to specification.
b. Verify fault was corrected, if required.
8. Maintain tools and equipment.
a. Ensure all tools are accounted for.
b. Ensure tools and equipment are cleaned properly.
9. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet), if required.
a. Annotate fault corrected on applicable forms.
b. Ensure paperwork gets turned-in to ULLS clerk.
20 May 2010
3-181
STP 9-91A14-SM-TG
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which technical manual was used.
b. Followed steps outlined in technical manual.
2. Selected and used correct tools and TMDE.
——
——
a. Identified applicable tools in BII.
b. Ensure serviceability of tools.
3. Followed prescribed safety procedures.
——
——
a. Followed procedures outlined in technical manual.
b. Followed safety precautions outlined in unit SOP.
4. Practiced maintenance discipline.
——
——
a. Followed safety guidelines outlined in motor-pool.
b. Ensured proper safety equipment was used.
5. Inspected vehicle Nose crane assembly and winch.
——
——
a. Followed steps outlined in technical manual.
b. Checked assembly for serviceability.
c. Checked for missing components.
6. Replaced nose crane assembly components, if required.
——
——
a. Followed steps outlined in technical manual.
b. Used proper tools for specified job.
c. Removed any damaged components.
d. Tagged and labeled broken components for turn-in, if needed.
7. Performed operational inspection.
——
——
a. Ensured parts were tightened to specification.
b. Verified fault was corrected, if required.
8. Maintained tools and equipment.
——
——
a. Ensured all tools were accounted for.
b. Ensured tools and equipment were cleaned properly.
9. Completed DA Form 5988-E, if required.
——
——
a. Annotated fault corrected on applicable forms.
b. Ensured paperwork got turned-in to ULLS Clerk.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
EM 0266
AR 385-10
FM 5-125
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-256-20-1
TM 9-2350-256-20-2
TM 9-2350-292-10
TM 9-2350-292-14&P
3-182
20 May 2010
STP 9-91A14-SM-TG
Maintain Micro Switches on a Tracked Recovery Vehicle
091-H8T-2019
Conditions: Starting in a classroom and later transitioning to the maintenance shop, with assistance, given
an M88A2 Tracked Recovery Vehicle, general mechanic's tool kit, special tools, test, measurement, and
diagnostic equipment (TMDE), safety equipment, required references, student handouts, and an
awareness of the contemporary operational environment (COE) variable and factors.
Note: If representative equipment is not available, use applicable equipment and associated references.
Standards: As a group, complete the practical exercise, "Maintain Micro Switches on a M88A2 Tracked
Recovery Vehicle", in accordance with the applicable technical publications, practical exercise checklist,
and student supplements within the time allotted. When this practical exercise is complete, all
performance measures must be met and the system must be fully operational. An instructor will verify your
group's work upon completion of this practical exercise.
Performance Steps
1. Select and use applicable publication.
a. identify which technical manual will be used.
b. Follow steps outlined in technical manual.
2. Follow prescribed safety procedures.
a. Follow procedures outlined in technical manual.
b. Follow safety procedures outlined in unit SOP.
3. Practice maintenance discipline.
a. Follow safety guidelines outlined in motor-pool.
b. Ensure proper safety equipment is used.
4. Inspect vehicle micro switches.
a. Follow steps outlined in technical manual.
b. Disconnect batteries, if needed.
c. Check for missing parts.
5. Replace micro switches, if required.
a. Follow steps outlined in technical manual.
b. Use proper tools for specified job.
c. Remove any damaged parts.
d. Tag and label any broken or worn parts for turn-in.
6. Perform operational inspection.
a. Ensure batteries are connected.
b. Ensure switches are properly functioning.
7. Maintain tools and equipment.
a. Ensure all tools are accounted for.
b. Clean and store tools properly.
8. Complete DA Form 5988-E (Equipment Inspection Maintenance Worksheet), as required.
a. Annotate fault corrected on applicable forms.
b. Ensure paperwork gets turned-in to ULLS clerk.
20 May 2010
3-183
STP 9-91A14-SM-TG
Performance Measures
GO
NO-GO
1. Selected and used applicable publications.
——
——
a. Identified which technical manual was used.
b. Followed steps outlined in technical manual.
2. Followed prescribed safety procedures.
——
——
a. Followed procedures outlined in technical manual.
b. Followed safety procedures outlined in unit SOP.
3. Practiced maintenance discipline.
——
——
a. Followed procedures outlined in motor-pool.
b. Ensured proper safety equipment was used.
4. Inspected vehicle micro switches.
——
——
a. Followed steps outlined in technical manual.
b. Disconnected batteries, if required.
c. Checked for missing parts.
d. Tagged and labeled any broken or worn parts for turn-in.
5. Replaced micro switches, if required.
——
——
a. Followed steps outlined in technical manual.
b. Used proper tools for specified job.
c. Removed any damaged parts.
d. Tagged and labeled any broken parts for turn-in.
6. Performed operational inspection.
——
——
a. Ensured batteries were connected.
b. Ensured switches were properly functioning.
7. Maintained tools and equipment.
——
——
a. Ensured all tools are accounted for.
b. Cleaned and stored tools properly.
8. Completed DA Form 5988-E, as required.
——
——
a. Annotated fault corrected on applicable forms.
b. Ensured paperwork got turned-in to ULLS clerk.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
EM 0266
AR 385-10
FM 5-125
AR 750-1
TM 9-2350-256-10
AR 750-43
TM 9-2350-292-10
TM 9-2350-292-14&P
3-184
20 May 2010

 

 

 

 

 

 

 

Content      ..      1      2      3      ..