Index Manuals SOLDIER'S MANUAL AND TRAINER'S GUIDE FOR ABRAMS TANK SYSTEM MAINTAINER MOS 91A SKILL LEVEL 1, 2, 3, and 4 (2010)
|
|
STP 9-91A14-SM-TG
SOLDIER'S MANUAL
AND
TRAINER'S GUIDE
FOR
ABRAMS TANK SYSTEM MAINTAINER
MOS 91A
SKILL LEVEL 1, 2, 3, and 4
MAY 2010
DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.
HEADQUARTERS, DEPARTMENT OF THE ARMY
∗SOLDIER TRAINING
HEADQUARTERS
PUBLICATION
DEPARTMENT OF THE ARMY
No. 9-91A14-SM-TG
Washington, DC, 20 May 2010
Soldier's Manual and Trainer's Guide
for
Abrams Tank System Maintainer
MOS 91A
Skill Levels 1, 2, 3, and 4
Contents
PAGE
PREFACE
viii
Chapter 1. INTRODUCTION
1-1
1-1. General
1-1
1-2. Task Summaries
1-1
1-3. Soldier’s Responsibilities
1-2
1-4. NCO Self-Development and the STP
1-2
1-5. Commander’s Responsibilities
1-2
1-6. Trainer’s Responsibilities
1-3
1-7. Training Support
1-3
Chapter 2. TRAINING GUIDE
2-1
2-1. General
2-1
2-2. Subject Area Codes
2-2
2-3. Duty Position Training Requirements
2-3
2-4. Critical Tasks List
2-4
Chapter 3. MOS/SKILL LEVEL TASKS
3-1
Skill Level 1
Subject Area 1: ADMINISTRATIVE TASKS (SKILL LEVEL 1/2)
091-109-0001 Maintain Test, Measurement, and Diagnostic Equipment (TMDE)
3-1
091-109-0002 Maintain Assigned Vehicles (PMCS)
3-3
091-109-0003 Maintain Assigned Tool Kits
3-5
091-109-0006 Maintain Equipment Inspection and Maintenance Worksheet (DA Form
2404) and (DA Form 5988-E)
3-7
DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.
*This Soldier’s Training Plan supersedes STP 9-63A14-SM-TG, dated 19 June 2009.
i
STP 9-91A14-SM-TG
Subject Area 2: TECHNICAL TASKS (SKILL LEVEL 1/2)
091-91A-0001 Correct Malfunction on the AGT 1500 Turbine Engine of the M1 Series Track
Vehicle
3-9
091-91A-0002 Replace Reduction Gear Box Assembly of the M1 Series Track Vehicle
3-11
091-91A-0003 Replace Accessory Gear Box Assembly of the M1 Series Track Vehicle
3-13
091-91A-0005 Replace Bearing Seals on an AGT 1500 Turbine Engine on a M1 Series
Track Vehicle
3-15
091-91A-0006 Replace Accessory Gear Box Seal Assembly of the M1 Series Track Vehicle
..............................................................................................................................3-17
091-91A-0007 Maintain Reduction Gear Box Lubrication System of the M1 Series Track
Vehicle
3-19
091-91A-0008 Correct Malfunction on the Engine Lubricating System of the M1 Series
Track Vehicle
3-21
091-91A-0009 Correct Malfunction on the Electrical Mechanical Fuel Management System
of the M1 Series Track Vehicle
3-23
091-91A-0010 Correct Malfunction of the Air Induction System of the M1 Series Track
Vehicle
3-25
091-91A-0011 Correct Malfunction on the Cooling System of the M1 Series Track Vehicle
3-27
091-91A-0012 Correct Malfunction of the Charging System of the M1 Series Track Vehicle
3-29
091-91A-0013 Correct Malfunction on the Starting System of the M1 Series Track Vehicle
3-31
091-91A-0014 Correct Malfunction on the Hull Electrical System of the M1 Series Track
Vehicle
3-33
091-91A-0015 Correct Malfunction on the Exterior Light System of the M1 Series Track
Vehicle
3-35
091-91A-0016 Correct Malfunction on the Transmission Assembly of the M1 Series Track
Vehicle
3-37
091-91A-0017 Correct Malfunction on the Suspension System of the M1 Series Track
Vehicle
3-39
091-91A-0018 Correct Malfunction on the Mechanical/Hydraulic Brake System of the M1
Series Track Vehicle
3-41
091-91A-0019 Correct Malfunction on the Mechanical/Hydraulic Steering System of the M1
Series Track Vehicle
3-43
091-91A-0021 Correct Malfunction on the Personnel Heater System of the M1 Series Track
Vehicle
3-45
091-91A-0022 Correct Malfunction on the Driver's Night Viewer Assembly of the M1 Series
Track Vehicle
3-47
091-91A-0024 Correct Malfunction on the Ammunition Storage Systems of the M1 Series
Track Vehicle
3-49
091-91A-0025 Correct Malfunction on the Hull Hydraulic System of the M1 Series Track
Vehicle
3-51
091-91A-0026 Correct Malfunction on the External Auxiliary Power Unit of the M1 Series
Track Vehicle
3-53
091-91A-0027 Correct Malfunction on the Fire Suppression System of the M1 Series Track
Vehicle
3-55
091-91A-0028 Correct Malfunction of the Chemical Biological Radiological Nuclear (CBRN)
Systems of the M1 Series Track Vehicle
3-57
091-91A-0029 Correct Malfunction on the Commander's Weapon Station System of the M1
Series Track Vehicle
3-59
091-91A-0030 Correct Malfunction on the Coaxial Weapon System of the M1 Series Track
Vehicle
3-62
ii
20 May 2010
STP 9-91A14-SM-TG
091-91A-0031 Correct Malfunction on the Fire Control System of the M1 Series Track
Vehicle
3-64
091-91A-0033 Correct Malfunction on the Traversing System of the M1 Series Track
Vehicle
3-66
091-91A-0034 Correct Malfunction on the Elevation System of the M1 Series Track Vehicle
..............................................................................................................................3-69
091-91A-0035 Correct Malfunction of Sighting Systems of the M1 Series Track Vehicle
3-72
091-91A-0036 Correct Malfunction on the Thermal Imaging System of the M1 Series Track
Vehicle
3-74
091-91A-0037 Correct Malfunction of the Main Weapon System of the M1 Series Track
Vehicle
3-76
091-91A-0039 Correct Malfunction on the Turret Electrical Systems of the M1 Series Track
Vehicle
3-78
091-91A-0040 Correct Malfunction of the Turret Hydraulics of the M1 Series Track Vehicle
3-80
091-91A-0041 Replace Traverse Motor Brake Assembly of the M1 Abrams Track Vehicle
3-83
091-91A-0042 Replace Manual Drive Assembly of the M1 Series Track Vehicle
3-85
091-91A-0043 Replace Elevation Servo Assembly of the M1 Series Track Vehicle
3-87
091-91A-0044 Perform Scheduled Services of the M1 Series Track Vehicle
3-89
091-91A-0046 Maintain the Hydraulic Accumulator Manual Elevation Drive Unit on the M1
Series Track Vehicle
3-91
091-91A-0047 Maintain Main Gun King Nut Bearing on the M1 Series Track Vehicle
3-94
Subject Area 3: JOINT ASSAULT BRIDGE/ARMORED BREACHER VEHICLE (ASI-D8 ONLY)
091-ABV-1001 Perform Preventive Maintenance Checks and Services (PMCS) on the ABV
..............................................................................................................................3-96
091-ABV-1002 Maintain ABV Hull Electrical System
3-98
091-ABV-1003 Maintain ABV Hull Hydraulic System
3-99
091-ABV-1004 Troubleshoot High Lift Adapter (HLA)
3-100
091-ABV-1005 Perform Hydraulic Pressure Check on Pressure Intensifier (PIU)
3-101
091-ABV-1006 Troubleshoot Plow Power Distribution Unit (PPDU)
3-102
091-ABV-1007 Perform Hydraulic Pressure Check on Hull 3-Base Manifold
3-103
091-ABV-1008 Troubleshoot High Lift Adapter (HLA) Jettison Pins
3-104
091-ABV-1009 Perform Hydraulic Pressure Check on Front End Equipment (FEE)
3-105
091-ABV-1010 Maintain ABV Turret Hydraulic System
3-106
091-ABV-1011 Maintain ABV Turret Electrical System
3-107
091-ABV-1012 Troubleshoot Turret power Distribution Unit (TPDU)
3-108
091-ABV-1013 Perform Hydraulic Pressure Check on Turret 3-Base Manifold
3-109
091-ABV-1014 Maintain ABV Turret Traversing System
3-110
091-ABV-1015 Maintain ABV Integrated Viewing System (IVS)
3-111
091-ABV-1016 Maintain Linear Demolition Charge System (LDCS)
3-112
091-ABV-1017 Maintain Lane Marking System (LMS)
3-113
091-ABV-1018 Troubleshoot Lane Marking System Unit (LMSCU)
3-114
091-ABV-1019 Maintain Lane Marking System (LMS) Compressor Assemblies
3-115
091-JAB-1001 Perform Preventive Maintenance Checks and Services (PMCS) on the JAB
and Bridge Launcher System
3-116
091-JAB-1002 Utilize Embedded Diagnostic System to Maintain JAB
3-117
091-JAB-1003 Maintain JAB Embedded Diagnostic System (EDS)
3-118
091-JAB-1004 Troubleshoot Vehicle using Embedded Diagnostic (ED) System
3-119
091-JAB-1005 Troubleshoot JAB Hull System
3-120
091-JAB-1006 Maintain JAB Hull Electrical System
3-121
20 May 2010
iii
STP 9-91A14-SM-TG
091-JAB-1007 Maintain JAB Hull Hydraulic System
3-122
091-JAB-1008 Maintain JAB Bridge Launcher System
3-123
091-JAB-1009 Maintain JAB Hydraulic Bridge Launcher System
3-124
091-JAB-1010 Maintain the JAB Turbine Hydraulic Pumping Unit (HPU) and Diesel
Hydraulic PUMP (DHP)
3-125
091-JAB-1011 Maintain the JAB Bridge and Bridge Launch System
3-126
091-JAB-1012 Maintain JAB Launcher Electrical System
3-127
091-JAB-1013 Maintain JAB Visual Enhancement System
3-128
Subject Area 4: RECOVERY (ASI-H8 ONLY)
091-H8C-2001 Locate a Recovery Site
3-129
091-H8C-2002 Determine Recovery Methods
3-131
091-H8C-2003 Operate Tactical Communications Equipment
3-133
091-H8C-2004 Operate Metal Cutting Equipment
3-135
091-H8T-2001 Maintain Recovery Vehicle Weapons
3-137
091-H8T-2002 Complete Preventive Maintenance Checks and Services on a Tracked
Recovery Vehicle
3-140
091-H8T-2003 Use Basic Issue Items Related to Tracked Recovery Vehicle
3-143
091-H8T-2004 Drive Tracked Recovery Vehicle
3-146
091-H8T-2005 Operate Auxiliary Power Unit
3-149
091-H8T-2006 Operate the Boom and Hoist Winch on a Tracked Recovery Vehicle
3-152
091-H8T-2007 Operate the Spade on a Tracked Recovery Vehicle
3-154
091-H8T-2008 Operate the Winches on a Tracked Recovery Vehicle
3-156
091-H8T-2009 Recover a Mired Tracked Vehicle
3-158
091-H8T-2010 Recover an Overturned Tracked Vehicle
3-161
091-H8T-2011 Tow a Tracked Vehicle on Improved/Highway Surface
3-164
091-H8T-2012 Tow of a Tracked Vehicle Cross Country
3-167
091-H8T-2013 Complete Field Expedient Recovery on a Tracked Vehicle
3-170
091-H8T-2014 Maintain Charging System on a Tracked Recovery Vehicle
3-172
091-H8T-2015 Maintain Starting System on a Tracked Recovery Vehicle
3-175
091-H8T-2016 Maintain Auxiliary Power Unit (APU) on a Tracked Recovery Vehicle
3-177
091-H8T-2017 Maintain Brake System on a Tracked Recovery Vehicle
3-179
091-H8T-2018 Maintain Nose Cone Assembly on a Tracked Recovery Vehicle
3-181
091-H8T-2019 Maintain Micro Switches on a Tracked Recovery Vehicle
3-183
091-H8T-2020 Perform Winch Ground Hop Procedures on a Tracked Recovery Vehicle
3-185
Subject Area 5: M1A2 SEP TASKS (ASI-K4 ONLY)
091-AK4-0079 Perform Plumb and Synchronization Procedures
3-187
091-AK4-0105 Maintain Hull Mission Processor Unit (HMPU)
3-189
091-AK4-0106 Maintain Turret Mission Processor Unit (TMPU)
3-191
091-AK4-0107 Maintain Commanders Display Unit (CDU)
3-193
091-AK4-0108 Maintain Gunners Control Display Panel (GCDP)
3-195
091-AK4-0109 Maintain Commanders Electronic Unit (CEU)
3-197
091-AK4-0111 Maintain Commanders Independent Thermal Viewer/Electronics (CITV/EU) ... 3-199
091-AK4-0112 Maintain Commanders Independent Thermal Viewer (CITV)
3-201
091-AK4-0114 Maintain Commanders Control Handle Assembly (CCHA)
3-203
091-AK4-0115 Maintain Data/Utility Bus Couplers
3-205
091-AK4-0116 Maintain Position/Navigation System (POS/NAV) Using Built In Test (BIT)
and Fault Isolation Test (FIT)
3-207
091-AK4-0117 Maintain Circuit Breaker System on the Soldier Machine Interface (SMI)
3-209
iv
20 May 2010
STP 9-91A14-SM-TG
091-AK4-0118 Maintain Second Generation Common Electronics Unit (SGCEU)
3-211
091-AK4-0119 Maintain Hull Power Distribution Unit (HPDU)
3-213
091-AK4-0120 Maintain Remote Switching Module (RSM)
3-215
091-AK4-0121 Maintain Analog Input Module (AIM)
3-217
091-AK4-0122 Maintain Turret Power Distribution System
3-219
091-AK4-0123 Maintain Drivers Integrated Display (DID)
3-221
091-AK4-0124 Maintain Global Positioning System (GPS)
3-223
091-AK4-0125 Maintain Commander's Independent Thermal Viewer (CITV) Second
Generation Servo Electronics Unit (SGSEU) (SEP)
3-225
091-AK4-0126 Maintain Second Generation Thermal Receiver Unit (SGTRU)
3-227
091-AK4-0127 Maintain Binocular Image Control Unit (BICU)
3-229
091-AK4-0128 Maintain Vapor Compression System Unit (VCSU)
3-231
091-AK4-0129 Maintain Air Handling Unit (AHU) Thermal Management System (TMS)
3-233
091-AK4-0132 Maintain the Fire Suppression System
3-235
091-AK4-0134 Maintain Fire Control Electronics Unit (FCEU)
3-237
091-AK4-0135 Maintain Mass Memory Unit (MMU)
3-239
091-AK4-0136 Operate the Maintenance Support Device (MSD)
3-241
091-AK4-0137 Identify the M1A2 SEP Unique Components
3-243
091-AK4-0138 Operate the Position/Navigation System (POS/NAV)
3-245
091-AK4-0139 Operate the Second Generation Forward Looking Infrared (FLIR) System
3-247
091-AK4-0140 Operate the Thermal Management System (TMS)
3-249
091-AK4-0141 Maintain Commander's Independent Thermal Viewer (CITV) Sight Mode
3-251
091-AK4-0142 Operate the Second Generation Thermal Imaging System (TIS)
3-253
091-AK4-1043 Maintain the Commanders Weapon System
3-255
Subject Area 6: WOLVERINE (ASI-V2 ONLY)
091-WOL-0001 Perform PMCS on Wolverine Bridge Assembly
3-257
091-WOL-0002 Commander's Station Familiarization
3-259
091-WOL-0003 Launch Bridge Under Normal Operations
3-260
091-WOL-0004 Troubleshoot Bridge Launch System
3-261
091-WOL-0005 Troubleshoot Launch Power Unit
3-263
091-WOL-0006 Remove and Install Launch Power Unit
3-265
091-WOL-0007 Ground Hop Launch Power Unit
3-267
091-WOL-0008 Remove and Install Hydraulic Module
3-269
091-WOL-0009 Remove and Install Charge Pump
3-271
091-WOL-0010 Remove and Install Bridge Advance Unit (Drive)
3-273
091-WOL-0011 Remove and Install Bridge Drive Manifold
3-275
091-WOL-0012 Remove and Install Laying Army Hydraulic Cylinder
3-276
091-WOL-0013 Remove and Install Improved Launcher Electronics Control Unit, (ILECU)
3-278
Skill Level 3
Subject Area 7: COMMON LOGISTIC TASKS (SKILL LEVEL 3)
091-CLT-3001 Manage a Maintenance Facility Safety Program
3-280
091-CLT-3002 Establish a Maintenance Facility Publications/Electronic Technical Manual
Library
3-282
091-CLT-3003 Establish Maintenance Facilities
3-284
091-CLT-3004 Prepare a Maintenance Facility Standing Operating Procedure
3-285
091-CLT-3005 Manage Tool Control Procedures
3-286
091-CLT-3006 Manage Key Control Procedures
3-287
20 May 2010
v
STP 9-91A14-SM-TG
091-CLT-3007 Manage the TMDE Calibration Program
3-288
091-CLT-3009 Supervise Maintenance Operations
3-289
091-CLT-3012 Manage Maintenance Information Systems Reports
3-292
Subject Area 8: TECHNICAL TASKS (SKILL LEVEL 3)
091-91A-3028 Perform Diagnostic Procedures on the AGT 1500 Turbine Engine of the M1
Series Track Vehicle
3-293
091-91A-3034 Perform Diagnostic Procedures on the Electrical Mechanical Fuel
Management System of the M1 Series Track Vehicle
3-296
091-91A-3035 Perform Diagnostic Procedures on the Air Induction System of the M1 Series
Track Vehicle
3-299
091-91A-3037 Perform Diagnostic Procedures on the Starting System of the M1 Series
Track Vehicle
3-301
091-91A-3038 Perform Diagnostic Procedures on the Hull Electrical System of the M1
Series Track Vehicle
3-303
091-91A-3040 Perform Diagnostic Procedures on the Transmission Assembly of the M1
Series Track Vehicle
3-305
091-91A-3046 Perform Diagnostic Procedures on the Ready Ammo Door of the M1 Series
Track Vehicle
3-307
091-91A-3047 Perform Diagnostic Procedures on the External Auxiliary Power Unit of the
M1 Series Track Vehicle
3-309
091-91A-3048 Perform Diagnostic Procedures on the Fire Suppression System of the M1
Series Track Vehicle
3-311
091-91A-3049 Perform Diagnostic Procedures on the Chemical Biological Radiological
Nuclear Systems of the M1 Series Track Vehicle
3-313
091-91A-3050 Perform Diagnostic Procedures on the Commander's Weapon Station of the
M1 Track Vehicle
3-315
091-91A-3052 Perform Diagnostic Procedures on the Fire Control System of the M1 Series
Track Vehicle
3-318
091-91A-3053 Perform Diagnostic Procedures on the Sighting Systems of the M1 Series
Track Vehicle
3-320
091-91A-3054 Perform Diagnostic Procedures on the Thermal Imaging System of the M1
Series Track Vehicle
3-322
091-91A-3055 Perform Diagnostic Procedures of the Turret Drive System of the M1 Series
Track Vehicle
3-324
091-91A-3056 Performed Diagnostic Procedures of the Elevation System of the M1 Series
Track Vehicle
3-326
091-91A-3058 Perform Diagnostic Procedures of the Main Weapon System of the M1
Series Track Vehicle
3-328
091-91A-3059 Perform Diagnostic Procedures of the Turret Electrical of the M1 Series
Track Vehicle
3-330
091-91A-3060 Perform Diagnostic Procedures of the Turret Hydraulics of the M1 Series
Track Vehicle
3-332
091-91A-3061 Perform Diagnostic Procedures of the Hull Hydraulic System of the M1
Series Track Vehicle
3-334
091-91A-3066 Perform Battlefield Damage Assessment and Repair of the M1 Series Track
Vehicle
3-336
091-91A-3068 Maintain the Turret Drive Angle Unit on a M1 Series Track Vehicle
3-339
091-91A-3073 Repair the Turret Race Ring Assembly on the M1 Series Track Vehicle
3-341
091-91A-3082 Repair Elevating Mechanism Assembly on the M1 Series Track Vehicle
3-343
091-91A-3083 Replace Rod End Bearing, Plain on the M1 Series Track Vehicle
3-346
091-91A-3085 Repair Gun Mount Assembly on the M1 Series Track Vehicle
3-348
vi
20 May 2010
STP 9-91A14-SM-TG
091-91A-3088 Repair Door Assembly, Ammunition on the M1 Series Track Vehicle
3-350
091-91A-3090 Maintain the 120MM Gun Cannon on the M1 Series Track Vehicle
3-352
091-91A-3092 Replace the Turret on the M1 Series Track Vehicle
3-354
091-91A-3094 Replace the Main Gun Tube on the M1 Series Track Vehicle
3-356
Skill Level 4
Subject Area 9: COMMON LOGISTIC MANAGEMENT TASKS (SKILL LEVEL 4)
091-CLT-4001 Perform Senior Rater Responsibilities for a Maintenance Section
-3-358
091-CLT-4002 Supervise Platoon/Section Administrative Procedures
3-359
091-CLT-4003 Manage Combat Stress
3-361
091-CLT-4006 Coordinate Support for the Maintenance Platoon/Section
3-362
091-CLT-4010 Integrate Automated Logistics Support Systems
3-363
091-CLT-4011 Plan Logistics Support for Maintenance Operations
3-364
091-CLT-4021 Prepare Standing Operating Procedures for Maintenance Operations
3-365
091-CLT-4022 Supervise the Deployment of Company Maintenance Team/Recovery
Support Team/Maintenance Support Team
3-366
091-CLT-4023 Conduct a Route Reconnaissance for a Maintenance Mission
3-367
091-CLT-4024 Conduct an Area Reconnaissance for a Maintenance Mission
3-368
091-CLT-4025 Manage Battlefield Maintenance Support
3-369
091-CLT-4026 Perform Support Operations NCO Duties
3-371
091-CLT-4027 Manage Maintenance Operations at a Maintenance Collection Point
3-372
091-CLT-4028 Provide Maintenance Support During Tactical Operations
3-373
Appendix A Hands-On Evaluation (DA Form 5164-R)
A-1
Appendix B Field Expedient Squad Book (DA Form 5165-R)
B-1
Glossary
Glossary-1
References
References-1
20 May 2010
vii
PREFACE
This soldier training publication (STP) is intended for soldiers holding MOS 91A, Skill Levels 1, 2, 3, and 4,
their supervisors, trainers, and commanders. It contains an MOS Training Plan providing information
needed to plan, conduct, and evaluate unit training, one of the most important jobs of military leaders. It
includes standardized training objectives in the form of task summaries that can be used to train and
evaluate soldiers on critical tasks supporting unit missions during wartime.
Soldiers holding MOS 91A should have access to this publication. Trainers and first line supervisors
should actively plan for soldiers’ access, making it available in work areas, unit learning centers, and unit
libraries. However, it is not intended for an individual copy to be provided to each MOS holder. The STP
is obtainable on line from the Reimer Digital Library (RDL).
This publication applies to the Active Army, the Army National Guard (ARNG)/Army National Guard of the
United States (ARNGUS), and the United States Army Reserve (USAR) unless otherwise stated.
The proponent of this publication is United States Army Training and Doctrine Command (TRADOC).
Submit comments and recommendations on DA Form 2028 (Recommended Changes to Publications and
Blank Forms) directly to: Department of the Army, Training Directorate, Ordnance Training Division, ATTN:
ATCL-TDF, Bldg 5020, 2221 Adams Avenue, Fort Lee, VA 23801-2102.
Unless this publication states otherwise, masculine nouns and pronouns do not refer exclusively to men.
viii
20 May 2010
STP 9-91A14-SM-TG
Chapter 1
Introduction
1-1. General.This soldier training publication (STP) identifies individual MOS training requirements for
soldiers holding MOS 91A. Commanders, trainers, and soldiers should use it to plan, conduct, and
evaluate individual training in units. The STP is the primary MOS reference for supporting
self-development, evaluating MOS proficiency, and training of 91A soldiers. Commanders employ two
primary methods to evaluate soldiers' proficiency:
·
Commander's evaluation. Commander’s evaluations are local tests or assessments of soldiers'
performance of MOS-specific and common tasks critical to the unit mission. They may be
conducted year-round.
·
Common task test (CTT). CTTs are hands-on tests used to evaluate proficiency on common
tasks. Alternate written tests are provided if equipment is not available for hands-on testing.
This publication is the soldier's primary reference to prepare for a commander's evaluation of MOS-specific
tasks. It contains task summaries for all critical tasks specific to the MOS and skill level (SL).
Commanders and trainers will use this soldier's manual/trainer's guide (SM/TG) to plan and conduct
training and commander's evaluations.
Chapter 2, Trainer’s Guide, contains information needed to plan training requirements for this MOS. The
trainer's guide—
·
Identifies subject areas in which soldiers must be trained.
·
Identifies critical tasks for each subject area.
·
Specifies where soldiers are initially trained on each task.
·
Recommends how often each task should be trained to sustain proficiency.
·
Recommends a strategy for cross-training soldiers.
·
Recommends a strategy for training soldiers to perform higher-level tasks.
Use this STP along with STP 21-1-SMCT (Soldier’s Manual of Common Tasks, Skill Level 1), STP
21-24-SMCT (Soldier’s Manual of Common Tasks, Skill Levels 2-4), Army training and evaluation programs
(ARTEPs), FM 7-0 (Training for Full Spectrum Operations) to establish effective training plans and
programs that integrate soldier, leader, and collective tasks.
1-2. Task Summaries. Task summaries outline wartime performance requirements for each critical task in
the STP. They provide both soldier and trainer with the information necessary to prepare, conduct, and
evaluate critical task training. As a minimum, task summaries include information soldiers must know and
skills they must perform to standard for each task. Following is the task summary format:
·
Task number. The task number is a 10-digit number that identifies the task and skill level.
Include the task number and title in any correspondence relating to the task.
·
Task title. The task title identifies the action to be performed.
·
Conditions. The task conditions statement describes the field or garrison conditions under which
the task will be performed and identifies the equipment, tools, references, job aids, and supporting
personnel that the soldier needs to perform the task in wartime.
20 May 2010
1-1
STP 9-91A14-SM-TG
·
Standards. The task standards describe how well and to what level of proficiency the soldier must
perform the task under wartime conditions. Standards are typically expressed in terms of
accuracy, completeness, duration, sequence, speed, and tolerance.
·
Performance measures. This section identifies specific actions that the soldier must accomplish
to complete the task successfully. Performance measures appear in a GO/NO-GO rating format
for easy evaluation. Some tasks may also include detailed training information in a Training
Information Outline and an Evaluation Preparation Section. The Evaluation Preparation Section
indicates necessary modifications to task performance in order to train and evaluate a task that
cannot be trained to the wartime standard under wartime conditions. It may also include special
training and evaluation preparation instructions to accommodate these modifications and any
instructions that should be given to the soldier before evaluation.
·
References. This section identifies references that provide more detailed explanations of task
performance requirements than are given in the task summary.
·
Warnings. Warnings alert users to the possibility of immediate personal injury or equipment
damage.
·
Notes. Notes provide additional supportive explanations or tips relating to task performance.
1-3. Soldier’s Responsibilities.Each soldier is responsible for performing individual tasks identified by the
first-line supervisor based on the unit’s mission-essential task list (METL). Soldiers must perform tasks to
the standards included in the task summary. If soldiers have questions about tasks or which tasks in this
manual they must perform, they are responsible for asking their first-line supervisor for clarification.
First-line supervisors know how to perform each task or can direct soldiers to appropriate training materials,
including current field manuals, technical manuals, and Army regulations. Soldiers are responsible for
using these materials to maintain performance. They are also responsible for maintaining performance of
all common tasks listed in the SMCTs at their current skill level and below.
Periodically, soldiers should ask their supervisor or another solder to check their performance to ensure that
they can perform the tasks.
1-4. NCO Self-Development and the STP. Self-development is a key component of leader development.
Leaders follow planned, progressive, sequential self-development programs developed by the individual
NCO and his or her first-line supervisor to enhance and sustain military competencies. Self-development
consists of individual study, research, professional reading, practice, and self-assessment. The
self-development concept requires NCOs, as Army professionals, to take responsibility for remaining
current in all phases of their MOS. The STP is the NCO’s primary source for maintaining MOS proficiency.
Another important resource for self-development is the Army Correspondence Course Program (ACCP).
Information is available at local education centers or on line through the Army Institute for Professional
Development (AIPD) web site, http://www.train.army.mil/. The web site offers on-line enrollment.
1-5. Commander’s Responsibilities. Commanders must ensure that their unit training plans prepare the
unit for war by enabling soldiers to develop and sustain proficiency in their MOS and skill level tasks.
Commanders should design unit training programs to provide individual training for all soldiers assigned to
the unit and to evaluate soldier proficiency routinely as part of the commander’s evaluation program. The
unit training program should also integrate individual training with crew drills and other collective training.
The MOS training plan provides information on which to base integration, cross-train, train-up, and
sustainment training programs. Commanders should use the MOS training plan when developing unit
training plans.
1-2
20 May 2010
STP 9-91A14-SM-TG
1-6. Trainer’s Responsibilities. Training is the business of all unit leaders. First-line leaders are the
principal trainers in the unit because they directly supervise soldiers and lead crews, squads, sections, and
teams.
Trainers can use the MOS training plan to determine the critical tasks each soldier is responsible for. They
should tell each soldier which tasks he or she must be able to perform. Trainers should evaluate task
performance to determine which tasks each soldier can or cannot perform to standard. Soldiers who
cannot perform a task to standard need further training. This STP helps the trainer do what trainers get
paid to do; train. Developing effective training is explained in detail in FM 25-100.
Every task summary in this STP includes performance measures, which trainers may use year-round to
determine if soldiers can perform critical tasks to the specified standards. The performance measures
identify what the trainer needs to observe to score a soldier’s performance. A blank space is provided for
the trainer to check either the GO or NO-GO column for each performance measure. Some tasks require
the trainer to watch the soldier perform them (evaluate the process). Other tasks call for the trainer to
focus on the results of the soldier’s performance (evaluate the product). Comments should not be written
on the task summary.
Trainers can monitor the progress of their soldiers by recording task go/no-go results. Trainers may use
DA Form 5164-R (Hands-On Evaluation) to record the performance measures a soldier passed or failed.
The form, which may be locally reproduced, applies to all tasks in this STP. Trainers may have DA Form
5164-R overprinted with information unique to their training requirements before reproducing it. See
Appendix A of this STP for a sample DA Form 5164-R with instructions.
Trainers may use DA Form 5165-R (Field Expedient Squad Book) to record hands-on go/no-go results for a
group of soldiers (for example, a crew, section, or squad) having the same MOS and skill level. This form
supports conduct of commander’s evaluations, and can be used to record training results gathered in the
field during slack time for all MOSs and skill levels. Use of this form is optional. See Appendix B for a
sample DA Form 5165-R with instructions. Trainers should work with each soldier until tasks can be
performed to specific task summary standards.
1-7. Training Support. References have been identified for each task to assist in planning and conducting
training. A consolidated list of references identified by type, publication number, and title and a
comprehensive glossary of acronyms, abbreviations, and definitions are included in this STP.
20 May 2010
1-3
This page intentionally left blank.
STP 9-91A14-SM-TG
Chapter 2
Training Guide
2-1.General. The MOS Training Plan (MTP) identifies the essential components of a unit training plan for
individual training. Units have different training needs and requirements based on differences in
environment, location, equipment, dispersion, and similar factors. Therefore, the MTP should be used as
a guide for conducting unit training and not a rigid standard. The MTP consists of two parts. Each part is
designed to assist the commander in preparing a unit training plan which satisfies integration, cross
training, training up, and sustainment training requirements for soldiers in this MOS.
Part One of the MTP shows the relationship of an MOS skill level between duty position and critical tasks.
These critical tasks are grouped by task commonality into subject areas.
Section I lists subject area numbers and titles used throughout the MTP. These subject areas are used to
define the training requirements for each duty position within an MOS.
Section II identifies the total training requirement for each duty position within an MOS and provides a
recommendation for cross training and train-up/merger training.
• Duty Position Column. This column lists the duty positions of the MOS, by skill level, which have
different training requirements.
• Subject Area Column. This column lists, by numerical key (see Section I), the subject areas a soldier
must be proficient in to perform in that duty position.
• Cross-Train Column. This column lists the recommended duty position for which soldiers should be
cross-trained.
• Train-Up/Merger Column. This column lists the corresponding duty position for the next higher skill
level or MOSC the soldier will merge into on promotion.
Part Two lists, by general subject areas, the critical tasks to be trained in an MOS and the type of training
required (resident, integration, or sustainment).
• Subject Area Column. This column lists the subject area number and title in the same order as
Section I, Part One of the MTP.
• Task Number Column. This column lists the task numbers for all tasks included in the subject area.
• Title Column. This column lists the task title for each task in the subject area.
• Training Location Column. This column identifies the training location where the task is first trained
to soldier training publications standards. If the task is first trained to standard in the unit, the word
“Unit” will be in this column. If the task is first trained to standard in the training base, it will identify, by
brevity code (ALC, SLC, etc.), the resident course where the task was taught. Figure 2-1 contains a list
of training locations and their corresponding brevity codes.
ASI
Additional Skill Identifier Course
AIT
Advanced Individual Training
ALC
Advanced Leader's Course
UNIT
Trained in the Unit
SLC
Senior Leader's Course
SNCOC
Senior NCO Course
ASI/SD
Additional Skill Identifier/Special Duty
Figure 2-1. Training Locations
20 May 2010
2-1
STP 9-91A14-SM-TG
• Sustainment Training Frequency Column. This column indicates the recommended frequency at
which the tasks should be trained to ensure soldiers maintain task proficiency. Figure 2-2 identifies the
frequency codes used in this column.
BA - Biannually
AN - Annually
SA - Semiannually
QT - Quarterly
MO - Monthly
BW - Biweekly
WK - Weekly
Figure 2-2. Sustainment Training Frequency Codes
• Sustainment Training Skill Level Column. This column lists the skill levels of the MOS for which
soldiers must receive sustainment training to ensure they maintain proficiency to soldier’s manual
standards.
2-2. Subject Area Codes.
Skill Level 1
1
ADMINISTRATIVE TASKS (SKILL LEVEL 1/2)
2
TECHNICAL TASKS (SKILL LEVEL 1/2)
3
JOINT ASSAULT BRIDGE/ARMORED BREACHER VEHICLE (ASI-D8 ONLY)
4
RECOVERY (ASI-H8 ONLY)
5
M1A2 SEP TASKS (ASI-K4 ONLY)
6
WOLVERINE (ASI-V2 ONLY)
Skill Level 3
7
COMMON LOGISTIC TASKS (SKILL LEVEL 3)
8
TECHNICAL TASKS (SKILL LEVEL 3)
Skill Level 4
9
COMMON LOGISTIC MANAGEMENT TASKS (SKILL LEVEL 4)
2-2
20 May 2010
STP 9-91A14-SM-TG
2-3. Duty Position Training Requirements.
91A CAREER FIELD DUTY POSITIONS
Duty Position
Subject
Cross
Train-up/Merger
Area
Train
Skill Level 1
Abrams Tank System Maintainer
NA
91A20 / Abrams Tank System Maintainer
Joint Assault Bridge/Armored
91A20 / Joint Assault Bridge/Armored
Breacher Vehicle Maintainer
Breacher Vehicle Maintainer (ASI-D8)
(ASI-D8)
1-2
91A20 / Recovery Vehicle Operator (ASI-H8)
Recovery Vehicle Operator (ASI-H8)
91A20 / M1A2 (SEP) Tank System Maintainer
M1A2 (SEP) Tank System
(ASI-K4)
Maintainer (ASI-K4)
91A20 / M104 Wolverine System Maintainer
M104 Wolverine System Maintainer
(ASIV2)
(ASI-V2)
Skill Level 2
Abrams Tank System Maintainer
NA
91A30 / Abrams Tank System Maintainer
Joint Assault Bridge/Armored
91A30 / Joint Assault Bridge/Armored
Breacher Vehicle Maintainer
Breacher Vehicle Maintainer (ASI-D8)
(ASI-D8)
91A30 / Recovery Vehicle Supervisor
Recovery Vehicle Operator (ASI-H8)
3-8
91A30 / M1A2 (SEP) Tank System Maintainer
M1A2 (SEP) Tank System
Maintainer (ASI-K4)
91A30 / M104 Wolverine System Maintainer
M104 Wolverine System Maintainer
(ASIV2)
(ASI-V2)
Skill Level 3
Abrams Tank System Maintainer
NA
9
91A40 / Abrams Tank Maintenance
Recovery Vehicle Supervisor
Supervisor
Skill Level 4
Abrams Tank Maintenance
N/A
NA
91Z50 / Mechanical Maintenance Supervisor
Supervisor
20 May 2010
2-3
STP 9-91A14-SM-TG
2-4. Critical Tasks List.
MOS TRAINING PLAN
91A14
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
Skill Level
1
Subject Area 1. ADMINISTRATIVE TASKS (SKILL LEVEL 1/2)
091-109-0001
Maintain Test, Measurement, and Diagnostic Equipment
AIT
SA
1/2
(TMDE)
091-109-0002
Maintain Assigned Vehicles (PMCS)
AIT
DA
1/2
091-109-0003
Maintain Assigned Tool Kits
AIT
DA
1/2
091-109-0006
Maintain Equipment Inspection and Maintenance
AIT
SA
1/2
Worksheet (DA Form 2404) and (DA Form 5988-E)
Subject Area 2. TECHNICAL TASKS (SKILL LEVEL 1/2)
091-91A-0001
Correct Malfunction on the AGT 1500 Turbine Engine of
AIT
QT
1/2
the M1 Series Track Vehicle
091-91A-0002
Replace Reduction Gear Box Assembly of the M1 Series
AIT
QT
1/2
Track Vehicle
091-91A-0003
Replace Accessory Gear Box Assembly of the M1 Series
AIT
QT
1/2
Track Vehicle
091-91A-0005
Replace Bearing Seals on an AGT 1500 Turbine Engine on
AIT
QT
1/2
a M1 Series Track Vehicle
091-91A-0006
Replace Accessory Gear Box Seal Assembly of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0007
Maintain Reduction Gear Box Lubrication System of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0008
Correct Malfunction on the Engine Lubricating System of
AIT
QT
1/2
the M1 Series Track Vehicle
091-91A-0009
Correct Malfunction on the Electrical Mechanical Fuel
AIT
QT
1/2
Management System of the M1 Series Track Vehicle
091-91A-0010
Correct Malfunction of the Air Induction System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0011
Correct Malfunction on the Cooling System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0012
Correct Malfunction of the Charging System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0013
Correct Malfunction on the Starting System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0014
Correct Malfunction on the Hull Electrical System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0015
Correct Malfunction on the Exterior Light System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0016
Correct Malfunction on the Transmission Assembly of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0017
Correct Malfunction on the Suspension System of the M1
AIT
QT
1/2
Series Track Vehicle
2-4
20 May 2010
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-91A-0018
Correct Malfunction on the Mechanical/Hydraulic Brake
AIT
QT
1/2
System of the M1 Series Track Vehicle
091-91A-0019
Correct Malfunction on the Mechanical/Hydraulic Steering
AIT
QT
1/2
System of the M1 Series Track Vehicle
091-91A-0021
Correct Malfunction on the Personnel Heater System of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0022
Correct Malfunction on the Driver's Night Viewer Assembly
AIT
QT
1/2
of the M1 Series Track Vehicle
091-91A-0024
Correct Malfunction on the Ammunition Storage Systems
AIT
QT
1/2
of the M1 Series Track Vehicle
091-91A-0025
Correct Malfunction on the Hull Hydraulic System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0026
Correct Malfunction on the External Auxiliary Power Unit of
AIT
QT
1/2
the M1 Series Track Vehicle
091-91A-0027
Correct Malfunction on the Fire Suppression System of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0028
Correct Malfunction of the Chemical Biological
AIT
QT
1/2
Radiological Nuclear (CBRN) Systems of the M1 Series
Track Vehicle
091-91A-0029
Correct Malfunction on the Commander's Weapon Station
AIT
QT
1/2
System of the M1 Series Track Vehicle
091-91A-0030
Correct Malfunction on the Coaxial Weapon System of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0031
Correct Malfunction on the Fire Control System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0033
Correct Malfunction on the Traversing System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0034
Correct Malfunction on the Elevation System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0035
Correct Malfunction of Sighting Systems of the M1 Series
AIT
QT
1/2
Track Vehicle
091-91A-0036
Correct Malfunction on the Thermal Imaging System of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0037
Correct Malfunction of the Main Weapon System of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0039
Correct Malfunction on the Turret Electrical Systems of the
AIT
QT
1/2
M1 Series Track Vehicle
091-91A-0040
Correct Malfunction of the Turret Hydraulics of the M1
AIT
QT
1/2
Series Track Vehicle
091-91A-0041
Replace Traverse Motor Brake Assembly of the M1
AIT
QT
1/2
Abrams Track Vehicle
091-91A-0042
Replace Manual Drive Assembly of the M1 Series Track
AIT
QT
1/2
Vehicle
091-91A-0043
Replace Elevation Servo Assembly of the M1 Series Track
AIT
QT
1/2
Vehicle
091-91A-0044
Perform Scheduled Services of the M1 Series Track
AIT
QT
1/2
Vehicle
20 May 2010
2-5
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-91A-0046
Maintain the Hydraulic Accumulator Manual Elevation
AIT
QT
1/2
Drive Unit on the M1 Series Track Vehicle
091-91A-0047
Maintain Main Gun King Nut Bearing on the M1 Series
AIT
QT
1/2
Track Vehicle
Subject Area 3. JOINT ASSAULT BRIDGE/ARMORED BREACHER VEHICLE (ASI-D8 ONLY)
091-ABV-1001
Perform Preventive Maintenance Checks and Services
ASI
WK
1/2
(PMCS) on the ABV
091-ABV-1002
Maintain ABV Hull Electrical System
ASI
QT
1/2
091-ABV-1003
Maintain ABV Hull Hydraulic System
ASI
QT
1/2
091-ABV-1004
Troubleshoot High Lift Adapter (HLA)
ASI
QT
1/2
091-ABV-1005
Perform Hydraulic Pressure Check on Pressure Intensifier
ASI
QT
1/2
(PIU)
091-ABV-1006
Troubleshoot Plow Power Distribution Unit (PPDU)
ASI
QT
1/2
091-ABV-1007
Perform Hydraulic Pressure Check on Hull 3-Base
ASI
QT
1/2
Manifold
091-ABV-1008
Troubleshoot High Lift Adapter (HLA) Jettison Pins
ASI
QT
1/2
091-ABV-1009
Perform Hydraulic Pressure Check on Front End
ASI
QT
1/2
Equipment (FEE)
091-ABV-1010
Maintain ABV Turret Hydraulic System
ASI
QT
1/2
091-ABV-1011
Maintain ABV Turret Electrical System
ASI
QT
1/2
091-ABV-1012
Troubleshoot Turret power Distribution Unit (TPDU)
ASI
QT
1/2
091-ABV-1013
Perform Hydraulic Pressure Check on Turret 3-Base
ASI
QT
1/2
Manifold
091-ABV-1014
Maintain ABV Turret Traversing System
ASI
QT
1/2
091-ABV-1015
Maintain ABV Integrated Viewing System (IVS)
ASI
QT
1/2
091-ABV-1016
Maintain Linear Demolition Charge System (LDCS)
ASI
QT
1/2
091-ABV-1017
Maintain Lane Marking System (LMS)
ASI
QT
1/2
091-ABV-1018
Troubleshoot Lane Marking System Unit (LMSCU)
ASI
QT
1/2
091-ABV-1019
Maintain Lane Marking System (LMS) Compressor
ASI
QT
1/2
Assemblies
091-JAB-1001
Perform Preventive Maintenance Checks and Services
ASI
WK
1/2
(PMCS) on the JAB and Bridge Launcher System
091-JAB-1002
Utilize Embedded Diagnostic System to Maintain JAB
ASI
QT
1/2
091-JAB-1003
Maintain JAB Embedded Diagnostic System (EDS)
ASI
QT
1/2
091-JAB-1004
Troubleshoot Vehicle using Embedded Diagnostic (ED)
ASI
QT
1/2
System
091-JAB-1005
Troubleshoot JAB Hull System
ASI
QT
1/2
091-JAB-1006
Maintain JAB Hull Electrical System
ASI
QT
1/2
091-JAB-1007
Maintain JAB Hull Hydraulic System
ASI
QT
1/2
091-JAB-1008
Maintain JAB Bridge Launcher System
ASI
QT
1/2
091-JAB-1009
Maintain JAB Hydraulic Bridge Launcher System
ASI
QT
1/2
091-JAB-1010
Maintain the JAB Turbine Hydraulic Pumping Unit (HPU)
ASI
QT
1/2
and Diesel Hydraulic PUMP (DHP)
091-JAB-1011
Maintain the JAB Bridge and Bridge Launch System
ASI
QT
1/2
2-6
20 May 2010
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-JAB-1012
Maintain JAB Launcher Electrical System
ASI
QT
1/2
091-JAB-1013
Maintain JAB Visual Enhancement System
ASI
QT
1/2
Subject Area 4. RECOVERY (ASI-H8 ONLY)
091-H8C-2001
Locate a Recovery Site
ASI/SD
SA
1/2
091-H8C-2002
Determine Recovery Methods
ASI/SD
SA
1/2
091-H8C-2003
Operate Tactical Communications Equipment
ASI/SD
SA
1/2
091-H8C-2004
Operate Metal Cutting Equipment
ASI/SD
SA
1/2
091-H8T-2001
Maintain Recovery Vehicle Weapons
ASI/SD
SA
1/2
091-H8T-2002
Complete Preventive Maintenance Checks and Services
ASI/SD
SA
1/2
on a Tracked Recovery Vehicle
091-H8T-2003
Use Basic Issue Items Related to Tracked Recovery
ASI/SD
AN
1/2
Vehicle
091-H8T-2004
Drive Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2005
Operate Auxiliary Power Unit
ASI/SD
SA
1/2
091-H8T-2006
Operate the Boom and Hoist Winch on a Tracked
ASI/SD
SA
1/2
Recovery Vehicle
091-H8T-2007
Operate the Spade on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2008
Operate the Winches on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2009
Recover a Mired Tracked Vehicle
ASI/SD
SA
1/2
091-H8T-2010
Recover an Overturned Tracked Vehicle
ASI/SD
SA
1/2
091-H8T-2011
Tow a Tracked Vehicle on Improved/Highway Surface
ASI/SD
SA
1/2
091-H8T-2012
Tow of a Tracked Vehicle Cross Country
ASI/SD
SA
1/2
091-H8T-2013
Complete Field Expedient Recovery on a Tracked Vehicle
091-H8T-2014
Maintain Charging System on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2015
Maintain Starting System on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2016
Maintain Auxiliary Power Unit (APU) on a Tracked
ASI/SD
SA
1/2
Recovery Vehicle
091-H8T-2017
Maintain Brake System on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2018
Maintain Nose Cone Assembly on a Tracked Recovery
ASI/SD
SA
1/2
Vehicle
091-H8T-2019
Maintain Micro Switches on a Tracked Recovery Vehicle
ASI/SD
SA
1/2
091-H8T-2020
Perform Winch Ground Hop Procedures on a Tracked
ASI/SD
SA
1/2
Recovery Vehicle
Subject Area 5. M1A2 SEP TASKS (ASI-K4 ONLY)
091-AK4-0079
Perform Plumb and Synchronization Procedures
ASI
QT
1/2
091-AK4-0105
Maintain Hull Mission Processor Unit (HMPU)
ASI
QT
1/2
091-AK4-0106
Maintain Turret Mission Processor Unit (TMPU)
ASI
QT
1/2
091-AK4-0107
Maintain Commanders Display Unit (CDU)
ASI
QT
1/2
091-AK4-0108
Maintain Gunners Control Display Panel (GCDP)
ASI
QT
1/2
091-AK4-0109
Maintain Commanders Electronic Unit (CEU)
ASI
QT
1/2
091-AK4-0111
Maintain Commanders Independent Thermal
ASI
QT
1/2
Viewer/Electronics (CITV/EU)
20 May 2010
2-7
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-AK4-0112
Maintain Commanders Independent Thermal Viewer
ASI
QT
1/2
(CITV)
091-AK4-0114
Maintain Commanders Control Handle Assembly (CCHA)
ASI
QT
1/2
091-AK4-0115
Maintain Data/Utility Bus Couplers
ASI
QT
1/2
091-AK4-0116
Maintain Position/Navigation System (POS/NAV) Using
ASI
QT
1/2
Built In Test (BIT) and Fault Isolation Test (FIT)
091-AK4-0117
Maintain Circuit Breaker System on the Soldier Machine
ASI
QT
1/2
Interface (SMI)
091-AK4-0118
Maintain Second Generation Common Electronics Unit
ASI
QT
1/2
(SGCEU)
091-AK4-0119
Maintain Hull Power Distribution Unit (HPDU)
ASI
QT
1/2
091-AK4-0120
Maintain Remote Switching Module (RSM)
ASI
QT
1/2
091-AK4-0121
Maintain Analog Input Module (AIM)
ASI
QT
1/2
091-AK4-0122
Maintain Turret Power Distribution System
ASI
QT
1/2
091-AK4-0123
Maintain Drivers Integrated Display (DID)
ASI
QT
1/2
091-AK4-0124
Maintain Global Positioning System (GPS)
ASI
QT
1/2
091-AK4-0125
Maintain Commander's Independent Thermal Viewer
ASI
QT
1/2
(CITV) Second Generation Servo Electronics Unit
(SGSEU) (SEP)
091-AK4-0126
Maintain Second Generation Thermal Receiver Unit
ASI
QT
1/2
(SGTRU)
091-AK4-0127
Maintain Binocular Image Control Unit (BICU)
ASI
QT
1/2
091-AK4-0128
Maintain Vapor Compression System Unit (VCSU)
ASI
QT
1/2
091-AK4-0129
Maintain Air Handling Unit (AHU) Thermal Management
ASI
QT
1/2
System (TMS)
091-AK4-0132
Maintain the Fire Suppression System
ASI
QT
1/2
091-AK4-0134
Maintain Fire Control Electronics Unit (FCEU)
ASI
QT
1/2
091-AK4-0135
Maintain Mass Memory Unit (MMU)
ASI
QT
1/2
091-AK4-0136
Operate the Maintenance Support Device (MSD)
ASI
QT
1/2
091-AK4-0137
Identify the M1A2 SEP Unique Components
ASI
QT
1/2
091-AK4-0138
Operate the Position/Navigation System (POS/NAV)
ASI
QT
1/2
091-AK4-0139
Operate the Second Generation Forward Looking Infrared
ASI
QT
1/2
(FLIR) System
091-AK4-0140
Operate the Thermal Management System (TMS)
ASI
QT
1/2
091-AK4-0141
Maintain Commander's Independent Thermal Viewer
ASI
QT
1/2
(CITV) Sight Mode
091-AK4-0142
Operate the Second Generation Thermal Imaging System
ASI
QT
1/2
(TIS)
091-AK4-1043
Maintain the Commanders Weapon System
ASI
QT
1/2
Subject Area 6. WOLVERINE (ASI-V2 ONLY)
091-WOL-0001
Perform PMCS on Wolverine Bridge Assembly
ASI
QT
1/2
091-WOL-0002
Commander's Station Familiarization
ASI
QT
1/2
091-WOL-0003
Launch Bridge Under Normal Operations
ASI
QT
1/2
091-WOL-0004
Troubleshoot Bridge Launch System
ASI
QT
1/2
2-8
20 May 2010
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-WOL-0005
Troubleshoot Launch Power Unit
ASI
QT
1/2
091-WOL-0006
Remove and Install Launch Power Unit
ASI
QT
1/2
091-WOL-0007
Ground Hop Launch Power Unit
ASI
QT
1/2
091-WOL-0008
Remove and Install Hydraulic Module
ASI
QT
1/2
091-WOL-0009
Remove and Install Charge Pump
ASI
QT
1/2
091-WOL-0010
Remove and Install Bridge Advance Unit (Drive)
ASI
QT
1/2
091-WOL-0011
Remove and Install Bridge Drive Manifold
ASI
QT
1/2
091-WOL-0012
Remove and Install Laying Army Hydraulic Cylinder
ASI
QT
1/2
091-WOL-0013
Remove and Install Improved Launcher Electronics Control
ASI
QT
1/2
Unit, (ILECU)
Skill Level 3
Subject Area 7. COMMON LOGISTIC TASKS (SKILL LEVEL 3)
091-CLT-3001
Manage a Maintenance Facility Safety Program
ALC
AN
3
091-CLT-3002
Establish a Maintenance Facility Publications/Electronic
ALC
AN
3
Technical Manual Library
091-CLT-3003
Establish Maintenance Facilities
ALC
AN
3
091-CLT-3004
Prepare a Maintenance Facility Standing Operating
ALC
AN
3
Procedure
091-CLT-3005
Manage Tool Control Procedures
ALC
AN
3
091-CLT-3006
Manage Key Control Procedures
ALC
AN
3
091-CLT-3007
Manage the TMDE Calibration Program
ALC
AN
3
091-CLT-3009
Supervise Maintenance Operations
ALC
AN
3
091-CLT-3012
Manage Maintenance Information Systems Reports
ALC
AN
3
Subject Area 8. TECHNICAL TASKS (SKILL LEVEL 3)
091-91A-3028
Perform Diagnostic Procedures on the AGT 1500 Turbine
ALC
QT
3
Engine of the M1 Series Track Vehicle
091-91A-3034
Perform Diagnostic Procedures on the Electrical
ALC
QT
3
Mechanical Fuel Management System of the M1 Series
Track Vehicle
091-91A-3035
Perform Diagnostic Procedures on the Air Induction
ALC
QT
3
System of the M1 Series Track Vehicle
091-91A-3037
Perform Diagnostic Procedures on the Starting System of
ALC
QT
3
the M1 Series Track Vehicle
091-91A-3038
Perform Diagnostic Procedures on the Hull Electrical
ALC
QT
3
System of the M1 Series Track Vehicle
091-91A-3040
Perform Diagnostic Procedures on the Transmission
ALC
QT
3
Assembly of the M1 Series Track Vehicle
091-91A-3046
Perform Diagnostic Procedures on the Ready Ammo Door
ALC
QT
3
of the M1 Series Track Vehicle
091-91A-3047
Perform Diagnostic Procedures on the External Auxiliary
ALC
QT
3
Power Unit of the M1 Series Track Vehicle
091-91A-3048
Perform Diagnostic Procedures on the Fire Suppression
ALC
QT
3
System of the M1 Series Track Vehicle
20 May 2010
2-9
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-91A-3049
Perform Diagnostic Procedures on the Chemical Biological
ALC
QT
3
Radiological Nuclear Systems of the M1 Series Track
Vehicle
091-91A-3050
Perform Diagnostic Procedures on the Commander's
ALC
QT
3
Weapon Station of the M1 Track Vehicle
091-91A-3052
Perform Diagnostic Procedures on the Fire Control System
ALC
QT
3
of the M1 Series Track Vehicle
091-91A-3053
Perform Diagnostic Procedures on the Sighting Systems of
ALC
QT
3
the M1 Series Track Vehicle
091-91A-3054
Perform Diagnostic Procedures on the Thermal Imaging
ALC
QT
3
System of the M1 Series Track Vehicle
091-91A-3055
Perform Diagnostic Procedures of the Turret Drive System
ALC
QT
3
of the M1 Series Track Vehicle
091-91A-3056
Performed Diagnostic Procedures of the Elevation System
ALC
QT
3
of the M1 Series Track Vehicle
091-91A-3058
Perform Diagnostic Procedures of the Main Weapon
ALC
QT
3
System of the M1 Series Track Vehicle
091-91A-3059
Perform Diagnostic Procedures of the Turret Electrical of
ALC
QT
3
the M1 Series Track Vehicle
091-91A-3060
Perform Diagnostic Procedures of the Turret Hydraulics of
ALC
QT
3
the M1 Series Track Vehicle
091-91A-3061
Perform Diagnostic Procedures of the Hull Hydraulic
ALC
QT
3
System of the M1 Series Track Vehicle
091-91A-3066
Perform Battlefield Damage Assessment and Repair of the
ALC
QT
3
M1 Series Track Vehicle
091-91A-3068
Maintain the Turret Drive Angle Unit on a M1 Series Track
ALC
QT
3
Vehicle
091-91A-3073
Repair the Turret Race Ring Assembly on the M1 Series
ALC
QT
3
Track Vehicle
091-91A-3082
Repair Elevating Mechanism Assembly on the M1 Series
ALC
QT
3
Track Vehicle
091-91A-3083
Replace Rod End Bearing, Plain on the M1 Series Track
ALC
QT
3
Vehicle
091-91A-3085
Repair Gun Mount Assembly on the M1 Series Track
ALC
QT
3
Vehicle
091-91A-3088
Repair Door Assembly, Ammunition on the M1 Series
ALC
QT
3
Track Vehicle
091-91A-3090
Maintain the 120MM Gun Cannon on the M1 Series Track
ALC
QT
3
Vehicle
091-91A-3092
Replace the Turret on the M1 Series Track Vehicle
ALC
QT
3
091-91A-3094
Replace the Main Gun Tube on the M1 Series Track
ALC
QT
3
Vehicle
Skill Level 4
Subject Area 9. COMMON LOGISTIC MANAGEMENT TASKS (SKILL LEVEL 4)
091-CLT-4001
Perform Senior Rater Responsibilities for a Maintenance
SLC
AN
4
Section
091-CLT-4002
Supervise Platoon/Section Administrative Procedures
SLC
AN
4
2-10
20 May 2010
STP 9-91A14-SM-TG
CRITICAL TASKS
Task Number
Title
Training
Sust
Sust
Location
Tng
Tng
Freq
SL
091-CLT-4003
Manage Combat Stress
SLC
AN
4
091-CLT-4006
Coordinate Support for the Maintenance Platoon/Section
SLC
AN
4
091-CLT-4010
Integrate Automated Logistics Support Systems
SLC
AN
4
091-CLT-4011
Plan Logistics Support for Maintenance Operations
SLC
AN
4
091-CLT-4021
Prepare Standing Operating Procedures for Maintenance
SLC
AN
4
Operations
091-CLT-4022
Supervise the Deployment of Company Maintenance
SLC
AN
4
Team/Recovery Support Team/Maintenance Support
Team
091-CLT-4023
Conduct a Route Reconnaissance for a Maintenance
SLC
AN
4
Mission
091-CLT-4024
Conduct an Area Reconnaissance for a Maintenance
SLC
AN
4
Mission
091-CLT-4025
Manage Battlefield Maintenance Support
SLC
AN
4
091-CLT-4026
Perform Support Operations NCO Duties
SLC
AN
4
091-CLT-4027
Manage Maintenance Operations at a Maintenance
SLC
AN
4
Collection Point
091-CLT-4028
Provide Maintenance Support During Tactical Operations
SLC
AN
4
20 May 2010
2-11
This page intentionally left blank.
STP 9-91A14-SM-TG
Chapter 3
MOS/Skill Level Tasks
Skill Level 1
Subject Area 1: ADMINISTRATIVE TASKS (SKILL LEVEL 1/2)
Maintain Test, Measurement, and Diagnostic Equipment (TMDE)
091-109-0001
Conditions: In a contemporary operational environment (COE) given applicable test, measurement, and
diagnostic equipment (TMDE); Army regulation (AR) 750-43; Technical Bulletin (TB) 43-180; Technical
Manual (TM) 9-6625-2301-14&P; TM 11-6625-3052-14; suitable tools; and suitable cleaning materials.
Standards: Maintain the TMDE in accordance with the applicable technical publications, procedures, and
specifications. When this task was completed, the equipment was fully mission-capable, calibration date
was current, and maintenance actions had been identified.
Performance Steps
1. Select and use applicable references.
2. Inspect TMDE for damage.
3. Test-operate TMDE to determine proper operation.
4. Check calibration date, if required.
5. Clean and/or lubricate TMDE, if required.
6. Store or package TMDE properly after maintenance or use.
7. Maintain the contact test set (CTS).
8. Complete The Army Maintenance Management System (TAMMS) forms, as required.
9. Perform required preventive maintenance checks and services (PMCS).
10. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
20 May 2010
3-1
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable references.
——
——
2. Inspected TMDE for damage.
——
——
3. Tested-operated TMDE to determine proper operation.
——
——
4. Checked calibration date, if required.
——
——
5. Cleaned and/or lubricated TMDE, if required.
——
——
6. Stored or packaged TMDE properly after maintenance or use.
——
——
7. Maintained the CTS.
——
——
8. Completed The Army Maintenance Management System (TAMMS) forms, as
——
——
required.
9. Performed required PMCS.
——
——
10. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 750-43
TB 43-180
TM 11-6625-3052-14
TM 9-6625-2301-14&P
3-2
20 May 2010
STP 9-91A14-SM-TG
Maintain Assigned Vehicles (PMCS)
091-109-0002
Conditions: In a contemporary operational environment (COE) given an assigned vehicle; repair parts;
petroleum, oil, lubricants (POL) products, if needed; additional tools and equipment as indicated in the
technical manuals (TMs); Department of the Army (DA) Pamphlet 750-8; DA Form 5988-E (Equipment
Inspection Maintenance Worksheet); other applicable technical publications; other necessary forms; and
supervision/assistance.
Standards: Maintain assigned vehicle preventive maintenance checks and services (PMCS) in
accordance with the applicable technical publications, procedures, and specifications. When this task was
completed, the vehicle was fully mission-capable or deficiencies/shortcomings were annotated and
required maintenance actions to be performed by other than assigned vehicle operator had been identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and test, measurement, and diagnostic equipment (TMDE).
3. Practice shop safety and maintenance discipline.
4. Perform PMCS in accordance with TM.
5. Annotate actions taken on DA Form 5988-E.
6. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Performed PMCS in accordance with TM.
——
——
5. Annotated actions taken on DA Form 5988-E.
——
——
6. Maintained tools and equipment.
——
——
20 May 2010
3-3
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
DA PAM 750-8
3-4
20 May 2010
STP 9-91A14-SM-TG
Maintain Assigned Tool Kits
091-109-0003
Conditions: In a contemporary operational environment (COE) given applicable tool kits, applicable
references, Technical Manual (TM) 9-243, Department of the Army (DA) Form 5988-E (Equipment
Inspection Maintenance Worksheet), cleaning materials, and solvents or lubricants.
Standards: Inspected and serviced the assigned tool kits in accordance with the applicable technical
publications, procedures, and specifications. When this task was completed, assigned tools were in
operable condition, tool kits or sets were complete, or section chief or supervisor were notified of shortages.
Performance Steps
1. Select and use applicable references.
2. Inspect tools for serviceability and accountability.
3. Practice shop safety and maintenance discipline.
4. Identify damaged items and notified supervisor.
5. Apply lubricants or preservatives, as needed.
6. Annotate corrective actions taken on DA Form 5988-E.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Selected and used applicable references.
——
——
2. Inspected tools for serviceability and accountability.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Identified damaged items and notified supervisor.
——
——
5. Applied lubricants or preservatives, as needed.
——
——
6. Annotated corrective actions taken on DA Form 5988-E.
——
——
20 May 2010
3-5
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-243
3-6
20 May 2010
STP 9-91A14-SM-TG
Maintain Equipment Inspection and Maintenance Worksheet (DA Form 2404) and (DA Form 5988-E)
091-109-0006
Conditions: In a contemporary operational environment (COE) given required equipment, Department of
the Army (DA) Form 2404 (Equipment Inspection and Maintenance Worksheet), DA Form 5988-E
(Equipment Inspection and Maintenance Worksheet), and applicable references.
Standards: DA Form 2404 and DA Form 5988-E are inspected and maintained in accordance with DA
Pamphlet 750-8 to ensure all required information had been correctly annotated.
Performance Steps
1. Perform administrative actions.
a. Select and use applicable references.
b. Practice shop safety and maintenance discipline.
2. Annotate deficiencies as required by technical manual and ensure all entries are complete, as
required.
3. Ensure all safety precautions and procedures are followed.
4. Ensure all entries are reviewed and verified by supervisor.
5. Ensure proper disposition of forms.
Evaluation Preparation: Provide the Soldier with the equipment and or materials described in the
condition statement.
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO NO-GO
1. Performed administrative actions.
——
——
a. Selected and used applicable references.
b. Practiced shop safety and maintenance discipline.
2. Annotated deficiencies as required by technical manual and ensured all entries are
——
——
complete, as required.
3. Ensured all safety precautions and procedures are followed.
——
——
4. Ensured all entries were reviewed and verified by supervisor.
——
——
5. Ensured proper disposition of forms.
——
——
20 May 2010
3-7
STP 9-91A14-SM-TG
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
AR 750-1
DA Form 2404
DA Form 5988-E
DA PAM 750-3
DA PAM 750-8
TM 9-2350-314-10
3-8
20 May 2010
STP 9-91A14-SM-TG
Subject Area 2: TECHNICAL TASKS (SKILL LEVEL 1/2)
Correct Malfunction on the AGT 1500 Turbine Engine of the M1 Series Track Vehicle
091-91A-0001
Conditions: In a contemporary operational environment (COE) given an M1A1 tank with basic issue items
(BII); Technical Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM
9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM
9-2350-264-34-1-1; TM 9-2350-264-34-1-2; TM 9-2385-255-34; Department of the Army (DA) Form 5988-E
(Equipment Inspection and Maintenance Worksheet) stating "Replace Reduction Gear Box Assembly of
the M1 Series Track Vehicle"; repair parts; tool kit, multi-capable; maintainer; special tools; test,
measurement, and diagnostic equipment (TMDE); equipment as indicated in TMs; and
supervision/assistance.
Standards: Correct the malfunction of the AGT 1500 gas turbine engine in accordance with applicable
technical publications. When the task is completed, the equipment or end item should be fully
mission-capable.
Performance Steps
1. Perform administrative actions.
a. Select and use applicable technical manuals.
b. Select and use applicable tools and test measurement, and diagnostic equipment (TMDE).
c. Practice shop safety and maintenance discipline.
2. Diagnose faults and determine maintenance action to be performed.
a. Inspect gas turbine power plant/pack systems and components.
b. Remove the power pack.
c. Groundhop the power pack.
d. Adjust IGV cable.
e. Perform troubleshooting of the air induction system.
3. Ensure all safety precautions and procedures are followed.
4. Replace defective components, as necessary.
5. Perform final operational test to verify the faults have been corrected.
6. Complete The Army Maintenance Management System (TAMMS) forms, as required.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-9
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
a. Selected and used applicable technical manuals.
b. Selected and used applicable tools and test measurement, and diagnostic
equipment (TMDE).
c. Practiced shop safety and maintenance discipline.
2. Selected and used applicable tools and TMDE.
——
——
a. Inspected gas turbine power plant/pack systems and components.
b. Removed the power pack.
c. Groundhopped the power pack.
d. Adjusted IGV cable.
e. Adjusted throttle control rotary variable differential transformer (RVDT).
3. Ensured all safety precautions and procedures are followed.
——
——
4. Replaced defective components, as necessary.
——
——
5. Performed final operational test to verify the faults have been corrected.
——
——
6. Completed The Army Maintenance Management System (TAMMS) forms, as
——
——
required.
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-243
TM 9-2350-264-10-2
TM 9-2835-255-34P
TM 9-2350-264-20-1-1
TM 9-8000
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-10
20 May 2010
STP 9-91A14-SM-TG
Replace Reduction Gear Box Assembly of the M1 Series Track Vehicle
091-91A-0002
Conditions: In a contemporary operational environment (COE) given an AGT 1500 power-pack and repair
parts; Technical Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM
9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM
9-2350-264-34-1-1; TM 9-2350-264-34-1-2; TM 9-2385-255-34; tool kit, multi-capable; DA Form 5988-E
(Equipment Inspection and Maintenance Worksheet) stating "Replace Reduction Gear Box Assembly of
the M1 Series Track Vehicle"; and special tools.
Standards: Repair the reduction gear box in accordance with applicable TM procedures and specifications.
When this task is completed, the equipment or end item is fully mission-capable or required maintenance
actions performed by other than military occupational specialty (MOS) 91A Skill Level (SL) 1/2 personnel
are identified.
Performance Steps
1. Select and use applicable publications.
2. Select and use correct tools and test, measurement and diagnostic equipment (TMDE).
3. Follow prescribed safety procedures.
4. Practice maintenance discipline.
5. Remove reduction gear box from rear engine module.
6. Inspect reduction gear box and seals.
7. Install reduction gear box.
8. Verify fault is corrected.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Selected and used correct tools and test, measurement and diagnostic equipment
——
——
(TMDE).
3. Followed prescribed safety procedures.
——
——
20 May 2010
3-11
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
4. Practiced maintenance discipline.
——
——
5. Removed reduction gear box from rear engine module.
——
——
6. Inspected reduction gear box and seals.
——
——
7. Installed reduction gear box.
——
——
8. Verified fault was corrected.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-243
TM 9-2350-264-10-2
TM 9-2835-255-34P
TM 9-2350-264-20-1-1
TM 9-8000
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-12
20 May 2010
STP 9-91A14-SM-TG
Replace Accessory Gear Box Assembly of the M1 Series Track Vehicle
091-91A-0003
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection and Maintenance Worksheet) stating "Replace
the Accessory Gear Box on the AGT 1500"; Technical Manual (TM) 9-2350-264-10-1; TM
9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM
9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM 9-2350-264-34-1-2; TM
9-2835-255-34; necessary tools and equipment as indicated in the TMs; test, measurement, and diagnostic
equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Replace the accessory gear box in accordance with applicable TM procedures and
specifications. When this task is completed, the equipment or end item is fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable publications.
2. Select and use correct tools and TMDE.
3. Follow prescribed safety procedures.
4. Practice maintenance discipline.
5. Remove accessory gear box assembly from forward module.
6. Inspect accessory gear box assembly and seals.
7. Install accessory gear box assembly.
8. Verify fault is corrected.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Selected and used correct tools and TMDE.
——
——
3. Followed prescribed safety procedures.
——
——
20 May 2010
3-13
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
4. Practiced maintenance discipline.
——
——
5. Removed accessory gear box assembly from forward module.
——
——
6. Inspected accessory gear box assembly and seals.
——
——
7. Installed accessory gear box assembly.
——
——
8. Verified fault is corrected.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-2835-255-34P
TM 9-2350-264-10-2
TM 9-8000
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-14
20 May 2010
STP 9-91A14-SM-TG
Replace Bearing Seals on an AGT 1500 Turbine Engine on a M1 Series Track Vehicle
091-91A-0005
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; Department of the Army (DA) Form 5988-E (Equipment Inspection Maintenance
Worksheet) stating "Replace Bearing Seals on the AGT 1500"; Technical Manual (TM) 9-2350-264-10-1;
TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM
9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM 9-2350-264-34-1-2; TM
9-2835-255-34; necessary tools and equipment as indicated in the TMs; test, measurement, and diagnostic
equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Replace the Bearing Seals on an AGT 1500 Engine in accordance with applicable TM
procedures and specifications. When this task is completed, the vehicle or equipment is fully
mission-capable or maintenance actions required to be performed by other than military occupational
specialty (MOS) 91A personnel are identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Remove and replace components in accordance with TMs.
7. Inspect equipment and components in accordance with TMs.
8. Perform all final checks to verify part is replaced to specifications.
9. Verify fault has been corrected.
10. Maintain tools and equipment to prevent damage.
11. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-15
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Removed and replaced components in accordance with TMs.
——
——
7. Inspected equipment and components in accordance with TMs.
——
——
8. Performed all final checks to verify part was replaced to specifications.
——
——
9. Verified fault had been corrected.
——
——
10. Maintained tools and equipment to prevent damage.
——
——
11. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-2835-255-34P
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-16
20 May 2010
STP 9-91A14-SM-TG
Replace Accessory Gear Box Seal Assembly of the M1 Series Track Vehicle
091-91A-0006
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Replace
Accessory Gear Box Seal Assembly of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; TM 9-2835-255-34; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Replace the accessory gear box seal assembly in accordance with applicable TM procedures
and specifications. When this task is completed, the vehicle or equipment is fully mission-capable or
maintenance actions required to be performed by other than military occupational specialty (MOS) 91A
personnel are identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Removed and replaced components in accordance with TMs.
7. Inspected equipment and components in accordance with TMs.
8. Perform all final checks to verify part is replaced to specifications.
9. Verify fault had been corrected.
10. Maintain tools and equipment to prevent damage.
11. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-17
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Removed and replaced components in accordance with TMs.
——
——
7. Inspected equipment and components in accordance with TMs.
——
——
8. Performed all final checks to verify part was replaced to specifications.
——
——
9. Verified fault had been corrected.
——
——
10. Maintained tools and equipment to prevent damage.
——
——
11. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-2835-255-34P
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-18
20 May 2010
STP 9-91A14-SM-TG
Maintain Reduction Gear Box Lubrication System of the M1 Series Track Vehicle
091-91A-0007
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Maintain
Reduction Gear Box Lubrication System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; TM 9-2835-255-34; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Clean Reduction Gear Box Lubrication System in accordance with applicable TM procedures
and specifications. When this task is completed, the vehicle or equipment is fully mission-capable or
maintenance actions required to be performed by other than military occupational specialty (MOS) 91A
personnel are identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Clean and lubricate components in accordance with publications and TMs.
7. Perform all final checks to verify part is replaced to specifications.
8. Verify fault has been corrected.
9. Maintain tools and equipment to prevent damage.
10. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-19
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools/TMDE.
——
——
6. Cleaned and lubricated components in accordance with publications and TMs.
——
——
7. Performed all final checks to verify part is replaced to specifications.
——
——
8. Verified fault had been corrected.
——
——
9. Maintained tools and equipment to prevent damage.
——
——
10. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-2835-255-34P
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-20
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Engine Lubricating System of the M1 Series Track Vehicle
091-91A-0008
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Engine Lubricating System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; TM 9-2835-255-34; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction on the Engine Lubricating System in accordance with applicable TM
procedures and specifications. When this task is completed, the vehicle or equipment is fully
mission-capable or maintenance actions required to be performed by other than military occupational
specialty (MOS) 91A personnel are identified.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Diagnose Engine Lubricating System and determine maintenance action to be performed.
7. Perform all final checks to verify part is replaced to specifications.
8. Verify fault has been corrected.
9. Maintain tools and equipment to prevent damage.
10. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-21
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Diagnosed Engine Lubricating System and determined maintenance action to be
——
——
performed.
7. Performed all final checks to verify part was replaced to specifications.
——
——
8. Verified fault had been corrected.
——
——
9. Maintained tools and equipment to prevent damage.
——
——
10. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-2835-255-34P
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-22
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Electrical Mechanical Fuel Management System of the M1 Series Track
Vehicle
091-91A-0009
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Electrical Mechanical Fuel Management System of the M1 Series Track Vehicle";
Technical Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM
9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM
9-2350-264-34-1-1; TM 9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Electrical Mechanical Fuel Management System in
accordance with performance measures and applicable technical publications and returned the M1 series
vehicle to fully mission-capable status.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Diagnose the Electrical Mechanical Fuel Management System and determine maintenance action to
be performed.
7. Verify fault has been corrected.
8. Maintain tools and equipment to prevent damage.
9. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-23
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Diagnosed the Electrical Mechanical Fuel Management System and determined
——
——
maintenance action to be performed.
7. Verified fault had been corrected.
——
——
8. Maintained tools and equipment to prevent damage.
——
——
9. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-2835-255-34P
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-2835-255-34
3-24
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction of the Air Induction System of the M1 Series Track Vehicle
091-91A-0010
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of the Air Induction System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Air Induction System in accordance with performance
measures and applicable technical publications and returned the M1 series vehicle to fully mission-capable
status.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Diagnose the Air Induction System and determine maintenance action to be performed.
7. Perform all final checks to verify part is replaced to specifications.
8. Verify fault has been corrected.
9. Maintain tools and equipment to prevent damage.
10. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-25
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Diagnosed the Air Induction System and determined maintenance action to be
——
——
performed.
7. Performed all final checks to verify part is replaced to specifications.
——
——
8. Verified fault had been corrected.
——
——
9. Maintained tools and equipment to prevent damage.
——
——
10. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-8000
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-26
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Cooling System of the M1 Series Track Vehicle
091-91A-0011
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Cooling System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions on the cooling system in accordance with performance measures
and applicable technical publications and returned the M1 series vehicle to fully mission-capable status.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Diagnose the cooling system and determine maintenance action to be performed.
7. Perform all final checks to verify part is replaced to specifications.
8. Verify fault has been corrected.
9. Maintain tools and equipment to prevent damage.
10. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-27
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Diagnosed the cooling system and determined maintenance action to be
——
——
performed.
7. Performed all final checks to verify part was replaced to specifications.
——
——
8. Verified fault had been corrected.
——
——
9. Maintained tools and equipment to prevent damage.
——
——
10. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-24P-1
DA Form 5988-E
TM 9-8000
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-28
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction of the Charging System of the M1 Series Track Vehicle
091-91A-0012
Conditions: In a contemporary operational environment (COE) given an applicable vehicle; tool kit,
multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of the Charging System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of vehicle charging system in accordance with applicable technical
publications. When the task is completed the equipment or end item will be fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill
level (SL) 1/2 personnel will be identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect vehicle charging system and components.
5. Diagnose fault(s) by troubleshooting the vehicle charging system.
6. Determine maintenance action to be performed.
7. Adjust and replace vehicle charging system and components.
8. Perform final operational test to verify that vehicle charging system malfunction is corrected to
specification.
9. Annotate corrective actions taken on the DA Form 5988-E.
10. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-29
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected vehicle charging system and components.
——
——
5. Diagnosed fault(s) by troubleshooting the vehicle charging system.
——
——
6. Determined maintenance action to be performed.
——
——
7. Adjusted and replaced vehicle charging system and components.
——
——
8. Performed final operational test to verify that vehicle charging system malfunction
——
——
was corrected to specification.
9. Annotated corrective actions taken on the DA Form 5988-E.
——
——
10. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-30
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Starting System of the M1 Series Track Vehicle
091-91A-0013
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Starting System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the starting system in accordance with performance measures
and applicable technical publications and returned the M1 series vehicle to fully mission-capable status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect vehicle starting system and components.
5. Diagnose vehicle starting system fault(s) by troubleshooting the starting system and air induction
system.
6. Determine maintenance action to be performed.
7. Adjust and/or replace vehicle starting system and components.
8. Perform a final operational test to verify that the vehicle starting system malfunction is corrected to
specification.
9. Annotate corrective actions taken on the DA Form 5988-E.
10. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-31
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected vehicle starting system and components.
——
——
5. Diagnosed vehicle starting system fault(s) by troubleshooting the starting system
——
——
and air induction system.
6. Determined maintenance action to be performed.
——
——
7. Adjusted and/or replaced vehicle starting system and components.
——
——
8. Performed a final operational test to verify that the vehicle starting system
——
——
malfunction was corrected to specification.
9. Annotated corrective actions taken on the DA Form 5988-E.
——
——
10. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-8000
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-32
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Hull Electrical System of the M1 Series Track Vehicle
091-91A-0014
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Hull Electrical System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of the Hull Electrical System in accordance with applicable technical
publications. When the task is completed, the equipment or end item is fully mission- capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect track hull electrical systems and components.
5. Diagnose track hull electrical system fault(s) by troubleshooting tank power distribution.
6. Replace the hull power distribution box.
7. Perform a final operational test to verify that the track hull electrical system malfunction is corrected to
specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-33
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected track hull electrical systems and components.
——
——
5. Diagnosed track hull electrical systems fault(s) by troubleshooting tank power
——
——
distribution.
6. Replaced the hull power distribution box.
——
——
7. Performed a final operational test to verify that the track hull electrical system
——
——
malfunction was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-34
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Exterior Light System of the M1 Series Track Vehicle
091-91A-0015
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Exterior Light System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Exterior Light System in accordance with performance
measures and applicable technical publications and returned the M1 series vehicle to fully mission-capable
status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect vehicle charging system and components.
5. Diagnose fault(s) by troubleshooting the exterior light system.
6. Determine maintenance action to be performed.
7. Adjust and replace exterior light system components.
8. Perform final operational test to verify that exterior light system malfunction is corrected to
specification.
9. Annotate corrective actions taken on the DA Form 5988-E.
10. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-35
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected vehicle charging system and components.
——
——
5. Diagnosed fault(s) by troubleshooting the exterior light system.
——
——
6. Determined maintenance action to be performed.
——
——
7. Adjusted and replaced exterior light system components.
——
——
8. Performed final operational test to verify that exterior light system malfunction was
——
——
corrected to specification.
9. Annotated corrective actions taken on the DA Form 5988-E.
——
——
10. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-8000
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-36
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Transmission Assembly of the M1 Series Track Vehicle
091-91A-0016
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Transmission Assembly of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of transmission assemblies in accordance with applicable technical
publications. When the task is completed, the equipment or end item is fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect cross drive transmission assemblies.
5. Diagnose cross drive transmission assembly fault(s) by troubleshooting the transmission shift
subsystem.
6. Determine maintenance action to be performed:
a. Replace 24-volt solenoid.
b. Replace modulator directional linear valve.
c. Replace forward/reverse directional linear valve body.
7. Perform a final operational test to verify that the cross drive transmission assembly's malfunction is
corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-37
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected cross drive transmission assemblies.
——
——
5. Diagnosed cross drive transmission assembly fault(s) by troubleshooting the
——
——
transmission shift subsystem.
6. Determined maintenance action to be performed:
——
——
a. Replaced 24-volt solenoid.
b. Replaced modulator directional linear valve.
c. Replaced forward/reverse directional linear valve body.
7. Performed a final operational test to verify that the cross drive transmission
——
——
assembly's malfunction was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-38
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Suspension System of the M1 Series Track Vehicle
091-91A-0017
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Suspension System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Suspension System in accordance with performance
measures and applicable technical publications. When the task is completed, the equipment or end item is
fully mission-capable or required maintenance actions to be performed by other than military occupational
specialty (MOS) 91A skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect track vehicle suspension systems and components.
5. Diagnose track vehicle suspension system fault(s).
6. Determine maintenance action to be performed:
a. Replace shock absorber housing assembly.
b. Replace idler wheel hub.
c. Replace compensating idler arm upper-spindle-sleeve bearings.
7. Perform a final operational test to verify that the track vehicle suspension systems malfunction(s) is
corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-39
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected track vehicle suspension systems and components.
——
——
5. Diagnosed track vehicle suspension system fault(s).
——
——
6. Determined maintenance action to be performed:
——
——
a. Replaced shock absorber housing assembly.
b. Replaced idler wheel hub.
c. Replaced compensating idler arm upper-spindle-sleeve bearings.
7. Performed a final operational test to verify that the track vehicle suspension
——
——
systems malfunction(s) was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-40
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Mechanical/Hydraulic Brake System of the M1 Series Track Vehicle
091-91A-0018
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Mechanical/Hydraulic Brake System of the M1 Series Track Vehicle"; Technical Manual
(TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of mechanical/hydraulic brake systems in accordance with applicable
technical publications. When the task is completed, the equipment or end item was fully mission-capable
or required maintenance actions to be performed by other than military occupational specialty (MOS) 91A
skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect mechanical/hydraulic brake systems and components.
5. Diagnose mechanical/hydraulic brake systems fault(s) and determine maintenance action to be
performed.
6. Adjust and/or replace mechanical/hydraulic brake systems and components.
7. Perform a final operational test to verify that the mechanical/hydraulic brake systems malfunction is
corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-41
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected mechanical/hydraulic brake systems and components.
——
——
5. Diagnosed mechanical/hydraulic brake systems fault(s) and determined
——
——
maintenance action to be performed.
6. Adjusted and/or replaced mechanical/hydraulic brake systems and components.
——
——
7. Performed a final operational test to verify that the mechanical/hydraulic brake
——
——
systems malfunction was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-42
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Mechanical/Hydraulic Steering System of the M1 Series Track Vehicle
091-91A-0019
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Mechanical/Hydraulic Steering System of the M1 Series Track Vehicle"; Technical
Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Mechanical/Hydraulic Steering System accordance with
performance measures and applicable technical publications and returned the M109 series vehicle to fully
mission-capable status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect mechanical/hydraulic steering systems and components.
5. Diagnose mechanical/hydraulic steering systems fault(s) and determine maintenance action to be
performed.
6. Adjust and/or replace mechanical/hydraulic steering systems and components.
7. Perform a final operational test to verify that the mechanical/hydraulic steering systems malfunction is
corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-43
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected mechanical/hydraulic steering systems and components.
——
——
5. Diagnosed mechanical/hydraulic steering systems fault(s) and determined
——
——
maintenance action to be performed.
6. Adjusted and/or replaced mechanical/hydraulic steering systems and components.
——
——
7. Performed a final operational test to verify that the mechanical/hydraulic steering
——
——
systems malfunction was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-44
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Personnel Heater System of the M1 Series Track Vehicle
091-91A-0021
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Personnel Heater System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the Personnel Heater System in accordance with performance
measures and applicable technical publications and returned the M109 series vehicle to fully
mission-capable status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Describe how systems and components operate and function.
5. Inspect heater fuel system and components.
6. Perform troubleshooting procedures on fuel system and components.
7. Replace defective fuel component.
8. Replace heater assembly.
9. Perform required preventive maintenance checks and services (PMCS).
10. Perform a final operational test to verify fault(s) have been corrected.
11. Annotate corrective actions taken on the DA Form 5988-E.
12. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-45
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Described how systems and components operate and function.
——
——
5. Inspected heater fuel system and components.
——
——
6. Performed troubleshooting procedures on fuel system and components.
——
——
7. Replaced defective fuel component.
——
——
8. Replaced heater assembly.
——
——
9. Performed required preventive maintenance checks and services (PMCS).
——
——
10. Performed a final operational test to verify fault(s) have been corrected.
——
——
11. Annotated corrective actions taken on the DA Form 5988-E.
——
——
12. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-46
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Driver's Night Viewer Assembly of the M1 Series Track Vehicle
091-91A-0022
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Driver's Night Viewer Assembly of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the driver's night viewer assembly in accordance with
performance measures and applicable technical publications and returned the M1 series vehicle to fully
mission-capable status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect driver's night vision viewer electrical systems and components.
5. Diagnose driver's night vision viewer electrical systems fault(s) by troubleshooting.
6. Replace the driver's night vision viewer.
7. Perform a final operational test to verify that the driver's night vision viewer malfunction is corrected to
specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-47
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected driver's night vision viewer electrical systems and components.
——
——
5. Diagnosed driver's night vision viewer electrical systems fault(s) by
——
——
troubleshooting.
6. Replaced the driver's night vision viewer.
——
——
7. Performed a final operational test to verify that the driver's night vision viewer
——
——
malfunction was corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
AR 385-10
TM 9-2350-264-10-1
TM 9-2350-264-24P-1
TM 9-2350-264-10-2
TM 9-2350-388-10-1
TM 9-2350-264-20-1-1
TM 9-2350-388-23-1-1
TM 9-2350-264-20-1-2
TM 9-2350-388-23-1-2
TM 9-2350-264-20-1-3
TM 9-2350-388-23-1-3
TM 9-2350-264-20-1-4
TM 9-2350-388-23-1-4
TM 9-2350-264-20-1-5
TM 9-2350-388-23-1-5
TM 9-2350-264-34-1-1
TM 9-2350-388-23-1-6
TM 9-2350-264-34-1-2
TM 9-2350-388-23-1-7
TM 9-8000
3-48
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Ammunition Storage Systems of the M1 Series Track Vehicle
091-91A-0024
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Ammunition Storage Systems of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-2-1; TM
9-2350-264-20-2-2; TM 9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM
9-2350-264-34-2-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the ammunition storage systems in accordance with
performance measures and applicable technical publications and returned the M1 series vehicle to fully
mission-capable status.
Performance Steps
1. Follow prescribed safety procedures.
2. Practice maintenance discipline.
3. Verify fault on DA Form 5988-E/DA Form 2404 (Equipment Inspection and Maintenance Worksheet).
4. Select and use applicable TMs.
5. Select and use correct tools and TMDE.
6. Diagnose malfunction annotated on DA Form 5988-E/DA Form 2404.
7. Remove and replace components in accordance with TMs.
8. Correct malfunction in accordance with publications and TMs.
9. Perform all final checks to verify parts are replaced to specifications.
10. Verify fault has been corrected.
11. Maintain tools and equipment to prevent damage.
12. Complete DA Form 5988-E in accordance with The Army Maintenance Management System
(TAMMS).
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-49
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Followed prescribed safety procedures.
——
——
2. Practiced maintenance discipline.
——
——
3. Verified fault on DA Form 5988-E/DA Form 2404.
——
——
4. Selected and used applicable TMs.
——
——
5. Selected and used correct tools and TMDE.
——
——
6. Diagnosed malfunction annotated on DA Form 5988-E/DA Form 2404.
——
——
7. Removed and replaced components in accordance with TMs.
——
——
8. Corrected malfunction in accordance with publications and TMs.
——
——
9. Performed all final checks to verify parts were replaced to specifications.
——
——
10. Verified fault had been corrected.
——
——
11. Maintained tools and equipment to prevent damage.
——
——
12. Completed DA Form 5988-E in accordance with The Army Maintenance
——
——
Management System (TAMMS).
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 2404
TM 9-2350-264-10
DA Form 5988-E
TM 9-2350-264-10-1
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-20-2-4
TM 9-2350-264-24P-2
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-50
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Hull Hydraulic System of the M1 Series Track Vehicle
091-91A-0025
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Hull Hydraulic System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of hydraulic systems in accordance with applicable TM. When this task is
completed, the equipment or end item was fully mission-capable or required maintenance actions to be
performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2 personnel are
identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect hydraulic system components.
5. Replace hydraulic pump.
6. Replace hydraulic filters.
7. Bleed air from hydraulic system.
8. Perform a final operational test to verify hydraulic systems malfunction is corrected to specification.
9. Replace and charge main hydraulic accumulator.
10. Annotate corrective actions taken on DA Form 5988-E.
11. Maintain tools and equipment.
Evaluation Preparation:
WARNING
Adhere to the following safety precautions when performing the tasks
listed in this manual: Do not remove a radiator cap or surge tank cap
unless the engine is cool. While working on electrical systems,
remove all rings, watches, and jewelry. Before working on the exhaust
system, make sure it is cool. Disconnect the negative battery cable
prior to performing any electrical system maintenance or when
performing repairs in the locality of electrical components. When
working around engines that are operating, wear hearing protection.
When removing components over 75 pounds, two personnel are
required.
20 May 2010
3-51
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected hydraulic system components.
——
——
5. Replaced hydraulic pump.
——
——
6. Replaced hydraulic filters.
——
——
7. Bled air from hydraulic system.
——
——
8. Performed a final operational test to verify hydraulic systems malfunction was
——
——
corrected to specification.
9. Replaced and charged main hydraulic accumulator.
——
——
10. Annotated corrective actions taken on DA Form 5988-E.
——
——
11. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-8000
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-52
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the External Auxiliary Power Unit of the M1 Series Track Vehicle
091-91A-0026
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the External Auxiliary Power Unit of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; TM 9-6115-542-24&P; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Corrected the malfunctions of the External Auxiliary Power Unit (EAPU) in accordance with
performance measures and applicable technical publications. When this task is completed, the equipment
or end item was fully mission-capable or required maintenance actions to be performed by other than
military occupational specialty (MOS) 91A skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect EAPU systems and components.
5. Diagnose EAPU fault(s) by troubleshooting applicable system on the M1A1 tank EAPU.
6. Determine maintenance action to be performed:
a. Disassemble EAPU.
b. Adjust and/or replace EAPU components.
c. Reassemble EAPU.
7. Perform a final operational test to verify that the EAPU malfunction is corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
20 May 2010
3-53
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected EAPU systems and components.
——
——
5. Diagnosed APU fault(s) by troubleshooting applicable system on M1A1 tank
——
——
EAPU.
6. Determined maintenance action to be performed:
——
——
a. Disassembled EAPU.
b. Adjusted and/or replaced EAPU components.
c. Reassembled EAPU.
7. Performed a final operational test to verify that the EAPU malfunction is corrected
——
——
to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-8000
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
TM 9-6115-542-24&P
3-54
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Fire Suppression System of the M1 Series Track Vehicle
091-91A-0027
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Fire Suppression System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM 9-2350-264-20-1-2; TM
9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM 9-2350-264-34-1-1; TM
9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test, measurement, and
diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of fire extinguisher/suppression systems in accordance with applicable
technical publications. When the task is completed, the equipment or end item is fully mission-capable or
required maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill
level (SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect fire extinguisher/suppression systems and components.
5. Diagnose fire extinguisher/suppression systems fault(s) by troubleshooting the crew fire
extinguisher/suppression system.
6. Replace crew compartment valve and bottle assembly.
7. Perform a final operational test to verify that the fire extinguisher/suppression systems malfunction is
corrected to specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
20 May 2010
3-55
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected fire extinguisher/suppression systems and components.
——
——
5. Diagnosed fire extinguisher/suppression systems fault(s) by troubleshooting the
——
——
crew fire extinguisher/suppression system.
6. Replaced crew compartment valve and bottle assembly.
——
——
7. Performed a final operational test to verify that the fire extinguisher/suppression
——
——
systems malfunction is corrected to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-56
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction of the Chemical Biological Radiological Nuclear (CBRN) Systems of the M1
Series Track Vehicle
091-91A-0028
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of the Chemical Biological Radiological Nuclear (CBRN) Systems of the M1 Series Track
Vehicle"; Technical Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-1-1; TM
9-2350-264-20-1-2; TM 9-2350-264-20-1-3; TM 9-2350-264-20-1-4; TM 9-2350-264-20-1-5; TM
9-2350-264-34-1-1; TM 9-2350-264-34-1-2; necessary tools and equipment as indicated in the TMs; test,
measurement, and diagnostic equipment (TMDE); replacement parts; and supervision/assistance.
Standards: Correct malfunction of the CBRN in accordance with the applicable technical publication
procedures and specifications.
(See Maintenance Allocation Chart for exact procedures authorized for
each MOS and skill level.) When this task is completed, the vehicle or equipment is fully-mission capable
or maintenance actions required to be performed by other than military occupational specialty (MOS) 91A
skill level (SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Describe how systems and components operate and function.
5. Inspect CBRN systems and components.
6. Troubleshoot main CBRN temp controller system and components.
7. Replace prioritization valve.
8. Repair defective CBRN hoses.
9. Adjust CBRN components.
10. Perform required preventive maintenance checks and services (PMCS).
11. Perform a final operational test to verify fault is corrected.
12. Annotate corrective actions taken on the DA Form 5988-E.
13. Maintain tools and equipment.
20 May 2010
3-57
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Described how systems and components operate and function.
——
——
5. Inspected CBRN systems and components.
——
——
6. Troubleshoot main CBRN temp controller system and components.
——
——
7. Replaced prioritization valve.
——
——
8. Repaired defective CBRN hoses.
——
——
9. Adjusted CBRN components.
——
——
10. Performed required preventive maintenance checks and services (PMCS).
——
——
11. Performed a final operational test to verify fault is corrected.
——
——
12. Annotated corrective actions taken on the DA Form 5988-E.
——
——
13. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-1
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-1-1
TM 9-2350-264-20-1-2
TM 9-2350-264-20-1-3
TM 9-2350-264-20-1-4
TM 9-2350-264-20-1-5
TM 9-2350-264-34-1-1
TM 9-2350-264-34-1-2
3-58
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Commander's Weapon Station System of the M1 Series Track Vehicle
091-91A-0029
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Commander's Weapon Station System of the M1 Series Track Vehicle"; Technical
Manual (TM) 9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Maintain the cupola/commander's weapon station/hatch assembly and replace or repair its
components in accordance with the applicable technical publication procedures and specifications.
(See
Maintenance Allocation Chart for exact procedures authorized for each MOS and skill level.) When this
task is completed, the vehicle or equipment is fully mission-capable or maintenance actions required to be
performed by other than military occupational specialty (MOS) 91A personnel are identified.
Performance Steps
1. Review work request.
2. Perform initial inspection.
3. Determine maintenance action to be performed.
4. Ensure proper tools were available.
5. Identify and requisition repair parts, if required.
a. Azimuth drive system.
b. Firing circuit.
6. Ensure The Army Maintenance Management System (TAMMS) procedures are followed.
7. Determine maintenance action to be performed.
8. Ensure applicable publications are available.
9. Ensure all safety precautions are followed.
10. Provide assistance, if necessary.
11. Ensure task is performed to acceptable standards.
12. Perform a final inspection.
13. Critique personnel on performance of task.
14. Ensure tools and equipment are properly maintained.
20 May 2010
3-59
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Reviewed work request.
——
——
2. Performed initial inspection.
——
——
3. Determined maintenance action to be performed.
——
——
4. Ensured proper tools were available.
——
——
5. Identified and requisitioned repair parts, if required.
——
——
a. Azimuth drive system.
b. Firing circuit.
6. Ensured The Army Maintenance Management System (TAMMS) procedures were
——
——
followed.
7. Determined maintenance action to be performed.
——
——
8. Ensured applicable publications were available.
——
——
9. Ensured all safety precautions were followed.
——
——
10. Provided assistance, if necessary.
——
——
11. Ensured task is performed to acceptable standards.
——
——
12. Performed a final inspection.
——
——
13. Critiqued personnel on performance of task.
——
——
14. Ensured tools and equipment were properly maintained.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
3-60
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-61
STP 9-91A14-SM-TG
Correct Malfunction on the Coaxial Weapon System of the M1 Series Track Vehicle
091-91A-0030
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Coaxial Weapon System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: The M1A1 rear coaxial ammo box must be maintained and its components replaced or
repaired in accordance with the applicable technical publication procedures and specifications.
(See
Maintenance Allocation Chart for exact procedures authorized for each MOS and skill level.) When this
task is completed, the vehicle or equipment must be fully mission-capable or maintenance actions required
to be performed by other than military occupational specialty (MOS) 91A personnel must be identified.
Performance Steps
1. Select and use applicable publications.
2. Select and use proper tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Describe how systems and components operate and function.
5. Inspect firing solenoids.
6. Troubleshoot firing solenoids and gunners control handles.
7. Replace firing solenoids.
8. Repair defective component(s).
9. Adjust systems and components.
10. Perform required preventive maintenance checks and services (PMCS).
11. Verify fault has been corrected.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
3-62
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable publications.
——
——
2. Selected and used proper tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Described how systems and components operated and functioned.
——
——
5. Inspected firing solenoids.
——
——
6. Troubleshoot firing solenoids and gunners control handles.
——
——
7. Replaced firing solenoids.
——
——
8. Repaired defective component(s).
——
——
9. Adjusted systems and components.
——
——
10. Performed required preventive maintenance checks and services (PMCS).
——
——
11. Verified fault has been corrected.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-63
STP 9-91A14-SM-TG
Correct Malfunction on the Fire Control System of the M1 Series Track Vehicle
091-91A-0031
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Fire Control System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of sighting and fire control systems in accordance with applicable TM.
When this task is completed, the equipment or end item is fully mission-capable or required maintenance
actions to be performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2
personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Inspect sighting and fire control system.
4. Run computer self-test.
5. Replace Gun Turret Drive Unit.
6. Replace Computer Electronics Unit.
7. Replace Line of Sight Unit.
8. Perform a final operational test to verify sighting and fire control systems malfunction is correct to
specification.
9. Annotate corrective actions taken on the DA Form 5988-E.
10. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
3-64
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Inspected sighting and fire control system.
——
——
4. Ran computer self-test.
——
——
5. Replaced Gun Turret Drive Unit.
——
——
6. Replaced Computer Electronics Unit.
——
——
7. Replaced Line of Sight Unit.
——
——
8. Performed a final operational test to verify sighting and fire control systems
——
——
malfunction is correct to specification.
9. Annotated corrective actions taken on the DA Form 5988-E.
——
——
10. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-65
STP 9-91A14-SM-TG
Correct Malfunction on the Traversing System of the M1 Series Track Vehicle
091-91A-0033
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Traversing System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of traversing systems in accordance with applicable technical publications.
When the task is completed, the equipment or end item is fully mission-capable or required maintenance
actions to be performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2
personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect the traversing system component(s).
5. Replace hydraulic turret valve.
a. Torque turret valve to specification.
b. Lock in place all four electrical connectors.
c. Tighten all hydraulic hoses and tubes a half turn past the point of firm resistance.
6. Bleed air from hydraulic system.
7. Maintain gunner's control grip assembly.
a. Adjust emergency mode.
b. Adjust normal mode.
8. Perform troubleshooting malfunction of auxiliary hydraulic subsystem.
9. Perform troubleshooting fault of gun azimuth (traverse) subsystem.
10. Replace and charge main hydraulic accumulator.
11. Replace and charge manual hydraulic accumulator.
12. Perform a final operational check to verify that the traversing system malfunction is corrected to
specification.
13. Annotate corrective action taken on DA Form 5988-E.
14. Maintain tools and equipment.
3-66
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected the traversing system component(s).
——
——
5. Replaced hydraulic turret valve.
——
——
a. Torqued turret valve to specification.
b. Locked in place all four electrical connectors.
c. Tightened all hydraulic hoses and tubes a half turn past the point of firm
resistance.
6. Bled air from hydraulic system.
——
——
7. Maintained gunner's control grip assembly.
——
——
a. Adjusted emergency mode.
b. Adjusted normal mode.
8. Performed troubleshooting malfunction of auxiliary hydraulic subsystem.
——
——
9. Performed troubleshooting fault of gun azimuth (traverse) subsystem.
——
——
10. Replaced and charged main hydraulic accumulator.
——
——
11. Replaced and charged manual hydraulic accumulator.
——
——
12. Performed a final operational check to verify that the traversing system malfunction
——
——
was corrected to specification.
13. Annotated corrective action taken on DA Form 5988-E.
——
——
14. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
20 May 2010
3-67
STP 9-91A14-SM-TG
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
3-68
20 May 2010
STP 9-91A14-SM-TG
Correct Malfunction on the Elevation System of the M1 Series Track Vehicle
091-91A-0034
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Elevation System of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of elevating systems in accordance with applicable technical publications.
When this task is completed, the equipment or end item was fully-mission capable or required maintenance
actions to be performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2
personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect the elevating system component(s).
5. Replace hydraulic turret valve.
a. Torque turret valve to specification.
b. Lock in place all four electrical connectors.
c. Tighten all hydraulic hoses and tubes a half turn past the point of firm resistance.
6. Replace elevation servo mechanism fluid filter.
7. Bleed air from hydraulic system.
8. Prime the manual elevation hand pump assembly.
9. Bleed air from the manual elevation hand pump assembly.
10. Adjust the zero degree elevation switch.
11. Perform troubleshooting malfunction of gun elevation subsystem.
12. Replace and charge main hydraulic accumulator.
13. Replace and charge manual hydraulic accumulator.
14. Perform a final operational test to verify that the elevating system malfunction is corrected to
specification.
15. Annotate corrective actions taken on the DA Form 5988-E.
16. Maintain tools and equipment.
20 May 2010
3-69
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected the elevating system component(s).
——
——
5. Replaced hydraulic turret valve.
——
——
a. Torqued turret valve to specification.
b. Locked in place all four electrical connectors.
c. Tightened all hydraulic hoses and tubes a half turn past the point of firm
resistance.
6. Replaced elevation servo mechanism fluid filter.
——
——
7. Bled air from hydraulic system.
——
——
8. Primed the manual elevation hand pump assembly.
——
——
9. Bled air from the manual elevation hand pump assembly.
——
——
10. Adjusted the zero degree elevation switch.
——
——
11. Performed troubleshooting malfunction of gun elevation subsystem.
——
——
12. Replaced and charged main hydraulic accumulator.
——
——
13. Replaced and charged manual hydraulic accumulator.
——
——
14. Performed a final operational test to verify that the elevating system malfunction is
——
——
corrected to specification.
15. Annotated corrective actions taken on the DA Form 5988-E.
——
——
16. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
3-70
20 May 2010
STP 9-91A14-SM-TG
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-71
STP 9-91A14-SM-TG
Correct Malfunction of Sighting Systems of the M1 Series Track Vehicle
091-91A-0035
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of Sighting Systems on a M1 Series Track Vehicle"; Technical Manual (TM) 9-2350-264-10-1;
TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM 9-2350-264-20-2-3; TM
9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary tools and equipment as
indicated in the TMs; test, measurement, and diagnostic equipment (TMDE); replacement parts; and
supervision/assistance.
Standards: Correct malfunction of sighting systems in accordance with applicable TM. When this task is
completed, the equipment or end item is fully mission-capable or required maintenance actions to be
performed by other than military occupational specialty (MOS) 91A skill level (SL) 1/2 personnel are
identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect sighting and fire control systems.
5. Replace commander's gunner's primary sight (GPS) extension.
6. Service commander's GPS extension.
7. Replace commander's weapon station (CWS) sight.
8. Replace GPS body assembly.
9. Service GPS.
10. Replace lower panel assembly.
11. Perform a final operational test to verify sighting and fire control systems malfunction is correct to
specification.
12. Annotate corrective actions taken on the DA Form 5988-E.
13. Maintain tools and equipment.
3-72
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected sighting and fire control systems.
——
——
5. Replaced commander's gunner's primary sight (GPS) extension.
——
——
6. Serviced commander's GPS extension.
——
——
7. Replaced commander's weapon station (CWS) sight.
——
——
8. Replaced GPS body assembly.
——
——
9. Serviced GPS.
——
——
10. Replaced lower panel assembly.
——
——
11. Performed a final operational test to verify sighting and fire control systems
——
——
malfunction is correct to specification.
12. Annotated corrective actions taken on the DA Form 5988-E.
——
——
13. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-73
STP 9-91A14-SM-TG
Correct Malfunction on the Thermal Imaging System of the M1 Series Track Vehicle
091-91A-0036
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Thermal Imaging System on a M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction on the Thermal Imaging System in accordance with performance
measures and applicable technical publications and returned the M1 series vehicle to fully mission-capable
status.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect Thermal Imaging System.
5. Replace Image Control Unit.
6. Service the Thermal Imaging System.
7. Perform a final operational test to verify sighting and fire control systems malfunction is correct to
specification.
8. Annotate corrective actions taken on the DA Form 5988-E.
9. Maintain tools and equipment.
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
3-74
20 May 2010
STP 9-91A14-SM-TG
Performance Measures
GO NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected Thermal Imaging System.
——
——
5. Replaced Image Control Unit.
——
——
6. Serviced the Thermal Imaging System.
——
——
7. Performed a final operational test to verify sighting and fire control systems
——
——
malfunction is correct to specification.
8. Annotated corrective actions taken on the DA Form 5988-E.
——
——
9. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-75
STP 9-91A14-SM-TG
Correct Malfunction of the Main Weapon System of the M1 Series Track Vehicle
091-91A-0037
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction of the Main Weapon System on a M1 Series Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of the Main Weapon System in accordance with applicable technical
publications. When the task is completed, the equipment or end item is fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect the cannon assembly system component(s).
5. Perform troubleshooting of the cannon assembly.
6. Replace operating shafts and bearings.
7. Repair breechblock.
8. Repair closing piston assembly.
9. Perform breechblock function check.
10. Perform firing circuit test.
11. Perform a final operational test to verify that the cannon assembly malfunction is corrected to
specification.
12. Annotate corrective actions taken on the DA Form 5988-E.
13. Maintain tools and equipment.
3-76
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected the cannon assembly system component(s).
——
——
5. Performed troubleshooting of the cannon assembly.
——
——
6. Replaced operating shafts and bearings.
——
——
7. Repaired breechblock.
——
——
8. Repaired closing piston assembly.
——
——
9. Performed breechblock function check.
——
——
10. Performed firing circuit test.
——
——
11. Performed a final operational test to verify that the cannon assembly malfunction is
——
——
corrected to specification.
12. Annotated corrective actions taken on the DA Form 5988-E.
——
——
13. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-77
STP 9-91A14-SM-TG
Correct Malfunction on the Turret Electrical Systems of the M1 Series Track Vehicle
091-91A-0039
Conditions: In a contemporary operational environment (COE) given an M1 series Main Battle Tank; tool
kit, multi-capable; DA Form 5988-E (Equipment Inspection Maintenance Worksheet) stating "Correct
Malfunction on the Turret Electrical Systems of the M1 Series Track Vehicle"; Technical Manual (TM)
9-2350-264-10-1; TM 9-2350-264-10-2; TM 9-2350-264-20-2-1; TM 9-2350-264-20-2-2; TM
9-2350-264-20-2-3; TM 9-2350-264-20-2-4; TM 9-2350-264-34-2-1; TM 9-2350-264-34-2-2; necessary
tools and equipment as indicated in the TMs; test, measurement, and diagnostic equipment (TMDE);
replacement parts; and supervision/assistance.
Standards: Correct malfunction of the turret electrical system in accordance with applicable technical
publications. When the task is completed, the equipment or end item is fully mission-capable or required
maintenance actions to be performed by other than military occupational specialty (MOS) 91A skill level
(SL) 1/2 personnel are identified.
Performance Steps
1. Select and use applicable technical publications.
2. Select and use applicable tools and TMDE.
3. Practice shop safety and maintenance discipline.
4. Inspect the turret electrical system component(s).
5. Read M1A1 wiring diagrams.
6. Replace turret networks box (TNB).
7. Perform TNB check.
8. Perform troubleshooting of turret electrical system.
9. Perform troubleshooting of circuit breaker monitor subsystem.
10. Perform troubleshooting of turret panel lights and dome lights subsystems.
11. Perform a final operational test to verify turret electrical system malfunction(s) is corrected to
specification.
12. Annotate corrective actions taken on DA Form 5988-E.
13. Maintain tools and equipment.
3-78
20 May 2010
STP 9-91A14-SM-TG
Evaluation Preparation:
WARNING
The following safety precautions must be adhered to when performing
the tasks listed in this manual: Do not remove a radiator cap or surge
tank cap unless the engine is cool. While working on electrical
systems, remove all rings, watches, and jewelry. Before working on
the exhaust system, make sure it is cool. Disconnect the negative
battery cable prior to performing any electrical system maintenance or
when performing repairs in the locality of electrical components.
When working around engines that are operating, wear hearing
protection. When removing components over 75 pounds, two
personnel are required.
Performance Measures
GO
NO-GO
1. Selected and used applicable technical publications.
——
——
2. Selected and used applicable tools and TMDE.
——
——
3. Practiced shop safety and maintenance discipline.
——
——
4. Inspected the turret electrical system component(s).
——
——
5. Read M1A1 wiring diagrams.
——
——
6. Replaced turret networks box (TNB).
——
——
7. Performed TNB check.
——
——
8. Performed troubleshooting of turret electrical system.
——
——
9. Performed troubleshooting of circuit breaker monitor subsystem.
——
——
10. Performed troubleshooting of turret panel lights and dome lights subsystems.
——
——
11. Performed a final operational test to verify turret electrical system malfunction(s) is
——
——
corrected to specification.
12. Annotated corrective actions taken on DA Form 5988-E.
——
——
13. Maintained tools and equipment.
——
——
Evaluation Guidance: Score the Soldier GO if all performance measures are passed. Score the Soldier
NO-GO if any performance measure is failed. If the Soldier fails any performance measure, show what was
done wrong and how to do it correctly.
References
Required
Related
DA Form 5988-E
TM 9-2350-264-24P-2
TM 9-2350-264-10-1
TM 9-2350-264-10-2
TM 9-2350-264-20-2-1
TM 9-2350-264-20-2-2
TM 9-2350-264-20-2-3
TM 9-2350-264-20-2-4
TM 9-2350-264-34-2-1
TM 9-2350-264-34-2-2
20 May 2010
3-79
////////////////////////////////////////// |
||
|
|
|