Hyundai i30 (2018 year). Manual - part 35
Engine compartment fuse panel
■ Kappa 1.0 T-GDI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
T2
F48
TCU 2
15A
E/R Junction Block (Fuse : F34)
S3
F49
SENSOR 3
10A
E/R Junction Block (RLY.7)
E4
F50
ECU 4
15A
ECM
F51
WIPER
25A
Wiper Relay
F52
HORN
15A
Horn Relay
■ Kappa 1.4 T-GDI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
S2
RCV Control Solenoid Valve , Purge Control Solenoid Valve, Oil Control Valve #1/#2,
F37
SENSOR 2
10A
A/Con Relay, E/R Junction Block (RLY.9)
7
E2
F38
ECU 2
10A
ECM
E1
F39
ECU 1
20A
ECM
F40
INJECTOR
INJECTOR
15A
-
S1
F41
SENSOR 1
15A
Oxygen Sensor (Up), Oxygen Sensor (Down)
7-77
Maintenance
Engine compartment fuse panel
■ Kappa 1.4 T-GDI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
IGNITION
IGN
F42
20A
Ignition Coil #1/#2/#3/#4
COIL
COIL
E3
F43
ECU 3
15A
ECM
F44
A/CON
10A
A/Con Relay
E5
F45
ECU 5
10A
ECM
S4
F46
SENSOR 4
15A
Vacuum Pump
3
F47
ABS 3
10A
ABS/ESP Control Module, Multipurpose Check Connector
T2
F48
TCU 2
15A
TCM, Transaxle Range Switch, E/R Junction Block (Fuse : F34)
S3
F49
SENSOR 3
10A
E/R Junction Block (RLY.7)
E4
F50
ECU 4
15A
ECM
F51
WIPER
25A
Wiper Relay
F52
HORN
15A
Horn Relay
7-78
Engine compartment fuse panel
■ Kappa 1.4 MPI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
Camshaft Position Sensor #1/#2, Purge Control Solenoid Valve,
S2
F37
SENSOR 2
10A
Oil Control Valve #1/#2, Variable Intake Solenoid Valve,
E/R Junction Block (RLY.1, RLY.2)
E2
F38
ECU 2
10A
ECM
E1
F39
ECU 1
20A
ECM
F40
INJECTOR
INJECTOR
15A
Injector #1/#2/#3/#4
S1
F41
SENSOR 1
15A
Oxygen Sensor (Up), Oxygen Sensor (Down)
IGNITION
IGN
F42
20A
Ignition Coil #1/#2/#3/#4, Condenser
COIL
COIL
E3
F43
ECU 3
15A
ECM
7
F44
A/CON
10A
-
E5
F45
ECU 5
10A
ECM
S4
F46
SENSOR 4
15A
-
3
F47
ABS 3
10A
ABS/ESP Control Module, Multipurpose Check Connector
7-79
Maintenance
Engine compartment fuse panel
■ Kappa 1.4 MPI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
T2
F48
TCU 2
15A
E/R Junction Block (Fuse : F34)
S3
F49
SENSOR 3
10A
E/R Junction Block (RLY.7)
E4
F50
ECU 4
15A
-
F51
WIPER
25A
Wiper Relay
F52
HORN
15A
Horn Relay
■ Gamma 1.6 MPI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
S2
Camshaft Position Sensor #1/#2, Purge Control Solenoid Valve, Oil Control Valve
F37
SENSOR 2
10A
#1/#2, Variable Intake Solenoid Valve, E/R Junction Block (RLY.1, RLY.2)
E2
F38
ECU 2
10A
ECM/PCM
E1
F39
ECU 1
20A
ECM/PCM
F40
INJECTOR
INJECTOR
15A
Injector #1/#2/#3/#4
S1
F41
SENSOR 1
15A
Oxygen Sensor (Up), Oxygen Sensor (Down)
7-80
Engine compartment fuse panel
■ Gamma 1.6 MPI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
IGNITION
IGN
F42
20A
Ignition Coil #1/#2/#3/#4, Condenser
COIL
COIL
E3
F43
ECU 3
15A
ECM/PCM
F44
A/CON
10A
-
E5
F45
ECU 5
10A
ECM/PCM
S4
F46
SENSOR 4
15A
-
3
F47
ABS 3
10A
ABS/ESP Control Module, Multipurpose Check Connector
T2
F48
TCU 2
15A
Transaxle Range Switch, E/R Junction Block (Fuse : F34)
S3
F49
SENSOR 3
10A
E/R Junction Block (RLY.7)
7
E4
F50
ECU 4
15A
ECM/PCM
F51
WIPER
25A
Wiper Relay
F52
HORN
15A
Horn Relay
7-81
Maintenance
Engine compartment fuse panel
■ U-II 1.6 TCI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
Oil Level Sensor , Electronic VGT Actuator, EGR Cooling Valve,
S2
F37
SENSOR 2
10A
Fuel Pressure Regulating Valve, PM Sensor, Stop Lamp Switch, A/Con Relay,
E/R Junction Block (RLY.2/5/11)
E2
F38
ECU 2
10A
-
E1
F39
ECU 1
20A
ECM
F40
INJECTOR
INJECTOR
15A
-
S1
F41
SENSOR 1
15A
Lambda Sensor #1/#2
IGNITION
IGN
F42
20A
Ignition Coil #1/#2/#3/#4
COIL
COIL
E3
F43
ECU 3
15A
ECM
F44
A/CON
10A
-
E5
F45
ECU 5
10A
ECM
S4
F46
SENSOR 4
15A
Fuel Filter Heater & Fuel Filter Warning Sensor, Glow Plug Unit
7-82
Engine compartment fuse panel
■ U-II 1.6 TCI
Fuse No.
Fuse Name
Symbol
Fuse Rating
Circuit Protected
3
F47
ABS 3
10A
ABS/ESP Control Module, Multipurpose Check Connector
T2
F48
TCU 2
15A
TCM, Transaxle Range Switch, E/R Junction Block (Fuse : F34)
S3
Air Flow Sensor, Rail Pressure Control Valve, Camshaft Position Sensor,
F49
SENSOR 3
10A
Oil Pressure Valve, E/R Junction Block (RLY.7)
E4
F50
ECU 4
15A
-
F51
WIPER
25A
Wiper Relay
F52
HORN
15A
Horn Relay
7
7-83
Maintenance
Engine compartment fuse panel
(Battery terminal cover)
OPD076066
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay name and capacity.
i
Information
Not all fuse panel descriptions in this
manual may be applicable to your
OPD076065
vehicle; the information is accurate at
the time of printing. When you inspect
NOTICE
the fuse panel in your vehicle, refer to
After checking the fuse panel in the engine compartment, securely
the fuse panel label.
install the cover. If it is not securely latched, electrical failure may occur
from water contact.
7-84
LIGHT BULBS
Consult an authorized HYUNDAI
NOTICE
i
Information
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
Be sure to replace the burned-out
The headlamp aiming should be adjust-
light bulbs because other parts of the
bulb with one of the same wattage
ed after an accident or after the head-
vehicle must be removed before you
rating. Otherwise, it may cause
lamp assembly is reinstalled at an
can get to the bulb. This is especially
damage to the fuse or electric
authorized HYUNDAI dealer.
true for removing the headlamp
wiring system.
assembly to get to the bulb(s).
i
Information - Traffic Change
Removing/installing the headlamp
i
Information
(for Europe)
assembly can result in damage to
After heavy driving, rain or washing,
The low beam light distribution is
the vehicle.
headlamp and tail lamp lenses could
asymmetric. If you go abroad to a coun-
appear frosty. This condition is caused
try with opposite traffic direction, this
by the temperature difference between
asymmetric part will dazzle oncoming
WARNING
the lamp inside and outside. This is
car driver. To prevent dazzle, ECE reg-
similar to the condensation on your
ulation demand several technical solu-
Prior to working on the light,
windows inside your vehicle during the
tions
(ex. automatic change system,
firmly apply the parking brake,
rain and doesn’t indicate a problem
adhesive sheet, down aiming). These
ensure that the ignition switch is
with your vehicle. If the water leaks
headlamps are designed not to dazzle
in the LOCK/OFF position and
into the lamp bulb circuitry, we rec-
opposite drivers. So, you need not
turn off the lights to avoid sud-
ommend that the system be checked
change your headlamps in a country
den movement of the vehicle and
by an authorized HYUNDAI dealer.
with opposite traffic direction.
7
burning your fingers or receiving
an electric shock.
7-85
Maintenance
Headlamp, static bending lamp,
•
Always handle them carefully, and
WARNING
position lamp, turn signal lamp
avoid scratches and abrasions. If
and daytime running light bulb
the bulbs are lit, avoid contact with
liquids.
replacement
•
Never touch the glass with bare
Type A
hands. Residual oil may cause the
bulb to overheat and burst when lit.
•
A bulb should be operated only
when installed in a headlamp.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
OLMB073042L
•
Handle halogen bulbs with
care. Halogen bulbs contain
pressurized gas that will pro-
duce flying pieces of glass that
OPDE076092
could cause injuries if broken.
(1) Headlamp (High)/Position lamp
•
Wear eye protection when
(2) Headlamp (Low)
changing a bulb. Allow the bulb
to cool down before handling it.
(3) Turn signal lamp
(4) Daytime running light
(if equipped)
7-86
■ High/Low beam
4. Disconnect the bulb socket-con-
Low
nector.
(for low beam and high
beam)
5. Remove the bulb from the head-
lamp assembly.
6. Install a new bulb.
7. Connect the bulb socket-connec-
tor. (for low beam and high beam)
High
8. Install the bulb cover by turning it
OPDE076076
clockwise.
■ Position lamp
OPDE076077
Turn signal lamp
1. Open the hood.
2. Disconnect the negative battery
cable.
3.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
OPDE076075
the socket align with the slots on
7
the assembly.
Headlamp and position lamp
4.Remove the bulb from the socket
1. Open the hood.
by pressing it in and rotating it
2. Disconnect the negative battery
counterclockwise until the tabs on
cable.
the bulb align with the slots in the
3. Remove the bulb cover by turning
socket. Pull the bulb out of the
it counterclockwise.
socket.
7-87
Maintenance
5.Insert a new bulb by inserting it into
5. Insert a new bulb by inserting it into
the socket and rotating it until it
the socket and rotating it until it
locks into place.
locks into place.
6.Install the socket in the assembly
6. Install the socket into the housing by
by aligning the tabs on the socket
aligning the tabs on the socket with
with the slots in the assembly.
the slots in the housing. Push the
socket into the housing and turn the
7.Push the socket into the assembly
socket clockwise.
and turn the socket clockwise.
OPDE076096
Daytime running light
1. Loosen the pin-type retainers of the
under cover and then remove the
undercover.
2. Reach your hand into the back of
the front bumper.
3. Remove the socket from the hous-
ing by turning the socket counter-
clockwise until the tabs on the sock-
et align with the slots of the housing.
4. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
7-88
Type B
• A bulb should be operated only
WARNING
when installed in a headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
■ High/Low beam
Low
OLMB073042L
OPD076042
• Handle halogen bulbs with
(1) Headlamp (High)
High
care. Halogen bulbs contain
(2) Headlamp (Low)
pressurized gas that will pro-
OPDE076076
(3) Turn signal lamp
duce flying pieces of glass that
■ Static bending light
could cause injuries if broken.
(4) Position lamp &
Daytime running light
• Wear eye protection when
changing a bulb. Allow the bulb
(5) Static bending light
7
to cool down before handling it.
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
OPDE076090
liquids.
• Never touch the glass with bare
Headlamp lamp and static bending
hands. Residual oil may cause the
light
bulb to overheat and burst when lit.
1. Open the hood.
7-89
Maintenance
2. Disconnect the negative battery
5.Insert a new bulb by inserting it into
cable.
the socket and rotating it until it
locks into place.
3. Remove the bulb cover by turning
it counterclockwise.
6.Install the socket in the assembly
by aligning the tabs on the socket
4. Disconnect the bulb socket-con-
with the slots in the assembly.
nector.
7.Push the socket into the assembly
5. Remove the bulb from the head-
lamp assembly.
and turn the socket clockwise.
6. Install a new bulb.
Position lamp and daytime running
7. Connect the bulb socket-connec-
tor.
OPDE076077
light
If the LED lamp does not operate, we
8. Install the bulb cover by turning it
Turn signal lamp
clockwise.
recommend you to have the vehicle
1. Open the hood.
checked by an authorized HYUNDAI
2. Disconnect the negative battery
dealer.
cable.
3.Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4.Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
7-90
Type C
Front fog lamp (if equipped)
Headlamp and front fog lamp
aiming (for Europe)
Headlamp aiming
■ Halogen type
■ LED type
OPD076041
OPDE076097
(1) Headlamp (Low)
1. Loosen the pin-type retainers of the
(2) Headlamp (High)
under cover and then remove the
OPDE076085/OPDE076086
undercover.
(3) Static bending light
1. Inflate the tires to the specified
2. Reach your hand into the back of the
pressure and remove any loads
(4) Position lamp & Turn signal lamp
front bumper.
from the vehicle except the driver,
& Daytime running light
3. Disconnect the power connector
spare tire, and tools.
7
from the socket.
2. The vehicle should be placed on a
Headlamp, static bending light,
4. Remove the bulb-socket from the
flat floor.
position lamp, turn signal lamp and
housing by turning the socket coun-
3. Draw vertical lines (Vertical lines
daytime running light
terclockwise until the tabs on the
passing through respective head
If the light bulb does not operate, we
socket align with the slots of the
lamp centers) and a horizontal line
recommend you to have the vehicle
housing.
(Horizontal line passing through
checked by an authorized HYUNDAI
5. Install a new bulb-socket into the
center of head lamps) on the
dealer.
housing by aligning the tabs on the
screen.
socket with the slots in the housing.
Push the socket into the housing
and turn the socket clockwise.
7-91
Maintenance
4. With the headlamp and battery in
Front fog lamp aiming
normal condition, aim the head-
lamps so the brightest portion falls
on the horizontal and vertical
lines.
5. To aim the low beam left or right,
turn the driver clockwise or coun-
terclockwise. To aim the low beam
up or down, turn the driver clock-
wise or counterclockwise.
To aim the high beam up or down,
turn the driver clockwise or coun-
terclockwise.
OPDE076087
The front fog lamp can be aimed as
the same manner of the headlamps
aiming. With the front fog lamps and
battery in normal condition, aim the
front fog lamps. To aim the front fog
lamp up or down, turn the driver
clockwise or counterclockwise.
7-92
Aiming point
H1 : Height between the head lamp bulb center and ground (Low beam)
H2 : Height between the head lamp bulb center and ground (High beam)
H3 : Height between the fog lamp bulb center and ground
W1 : Distance between the two head lamp bulbs centers (Low beam)
W2 : Distance between the two head lamp bulbs centers (High beam)
7
W3 : Distance between the two fog lamp bulbs centers
OPDE076081
Unit: mm (in)
Vehicle
Lamp type
H1
H2
H3
W1
W2
W3
condition
Halogen
681 (26.81)
645 (25.39)
1,440 (56.69)
1,218 (47.95)
Without driver
344 (13.54)
LED
677 (26.65)
631 (24.84)
1,385 (54.52)
1,114 (43.85)
1,484 (58.42)
Halogen
676 (26.61)
640 (25.19)
1,440 (56.69)
1,218 (47.95)
With driver
339 (13.34)
LED
672 (26.45)
626 (24.64)
1,385 (54.52)
1,114 (43.85)
7-93