Volkswagen Corrado (1993 year). Manual - part 77

 

  Index      Volkswagen     Volkswagen Corrado - service repair manual 1993 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  75  76  77  78   ..

 

 

Volkswagen Corrado (1993 year). Manual - part 77

 

 

2.8L IN-LINE V6 (VR6) 

TORQUE SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                   Ft. Lbs. (N.m)

A/C Bracket-To-Engine Bolt  .......................  22 (30)
Axle Shaft-To-Transaxle Drive Flange Bolt  ........  33 (45)
Camshaft Bearing Cap Bolt  ........................  15 (20)
Camshaft Sprocket Bolt  ..........................  74 (100)
Clutch Cover Bolt  ................................  15 (20)
Connecting Rod Bolt  ...................  22 (30) + 1/4 Turn
Crankshaft Main Bearing Cap Bolt  ......  22 (30) + 1/2 Turn
Cylinder Head Bolt (1)
  Step 1  .........................................  30 (40)
  Step 2  .........................................  44 (60)
  Step 3  .......................  Additional 1/4 (90

ø

) Turn

  Step 4  .......................  Additional 1/4 (90

ø

) Turn

Engine Bracket (Front)  ...........................  44 (60)
Engine Bracket (To Body)  .........................  33 (45)
Engine-To-Transaxle 10-mm Bolt  ...................  44 (60)
Engine-To-Transaxle 12-mm Bolt  ...................  55 (80)
Exhaust Manifold-To-Cylinder Head Bolt & Nut  .....  18 (25)
Exhaust Pipe-To-Catalytic Converter Bolt  .........  18 (25)
Exhaust Pipe-To-Manifold Nut  .....................  30 (40)
Flywheel-To-Crankshaft Bolt  ...........  44 (60) + 1/4 Turn
Intake Manifold  ..................................  18 (25)
Intermediate Shaft Sprocket Bolt  ................  74 (100)
Oil Pan Bolt  .....................................  15 (20)
Oil Pan Drain Plug  ...............................  37 (50)
Oil Pressure Switch  ..............................  18 (25)
Oil Pump Cover Long Bolt  .............................  (2)
Oil Pump Cover Short Bolt  ........................  18 (25)
Power Steering Pump Bracket Bolt  .................  18 (25)
Pressure Plate Bolt  ..............................  15 (20)
Starter Mount Bolt  ...............................  18 (25)
Timing Belt Tensioner Nut  ........................  15 (20)
Torque Converter-To-Carrier Plate Bolt  ...........  22 (30)
Vibration Damper Bolt  ..........................  332 (450)
Water Pump Pulley Bolt  ...........................  15 (20)
Water Pump Housing-To-Engine Bolt  ................  15 (20)

                                             INCH Lbs. (N.m)

Fuel Rail Bolt (Lower) ............................  89 (10)
Timing Belt Idler Bolt  ...........................  89 (10)
Valve Cover Retaining Nut  ........................  89 (10)
Water Pump-To-Housing  ...........................  115 (13)

(1) - Never reuse cylinder head bolt(s) when servicing.
(2) - Tighten bolt to 89 INCH lbs. (10 N.m).

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

2.8L IN-LINE V6 (VR6) 

         GENERAL ENGINE SPECIFICATIONS

GENERAL ENGINE SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                    Specification

Displacement ...........................  170 Cu. In. (2.8L)
Bore ......................................  3.19" (81.0 mm)
Stroke ....................................  3.56" (90.3 mm)
Compression Ratio ..................................  10.5:1
Fuel System ..................................  Motronic MFI
Horsepower @ RPM
 Corrado SLC ...................................  178 @ 5800
 Passat ........................................  172 @ 5800
Torque Ft. Lbs @ RPM ...........................  177 @ 4200

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECS

CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS SPECS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                         In. (mm)

Crankshaft
  End Play
   Standard ...........................  .003-.007 (.07-.17)
   Service Limit ...............................  .010 (.25)
   Runout ......................................  .001 (.03)
Main Bearings
  Journal Diameter ..............  2.361-2.363 (59.98-60.04)
  Journal Out-Of-Round .........................  .001 (.03)
  Journal Taper ................................  .001 (.03)
  Oil Clearance
   Standard .........................  .0008-.0020 (.02-.06)
   Service Limit ...............................  .007 (.17)
Connecting Rod Bearings
  Journal Diameter ..............  1.881-1.883 (47.78-47.84)
  Journal Out-Of-Round .........................  .001 (.03)
  Journal Taper ................................  .001 (.03)
  Oil Clearance ......................  .0004-.002 (.01-.06)

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         PISTONS, PINS & RINGS SPECIFICATIONS

PISTONS, PINS & RINGS SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                         In. (mm)

Pistons

2.8L IN-LINE V6 (VR6) 

(1) - Information not available from manufacturer.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         CYLINDER BLOCK SPECIFICATIONS

CYLINDER BLOCK SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                         In. (mm)

Cylinder Bore
  Standard Diameter .........................  3.189 (81.01)
  Maximum Taper ...............................  .0032 (.08)
  Maximum Out-of-Round .........................  .001 (.03)

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         OIL PUMP SPECIFICATIONS

OIL PUMP SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                    Specification

Pump Gear Clearance
  Radial (Maximum) .........................  .008" (.20 mm)
  Axial (Maximum) ..........................  .004" (.10 mm)

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

2.8L IN-LINE V6 (VR6) 

VALVES SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                    Specification

Intake Valves
  Face Angle ..........................................  45

ø

  Head Diameter .........................  1.535" (39.00 mm)
  Length ...............................  4.210" (106.95 mm)
  Minimum Margin (1) ..................................  (2)
  Stem Diameter ...........................  .274" (6.97 mm)
Exhaust Valves
  Face Angle ..........................................  45

ø

  Head Diameter .........................  1.346" (34.20 mm)
  Length ...............................  4.210" (106.95 mm)
  Minimum Margin (1) ..................................  (2)
  Stem Diameter ...........................  .243" (6.95 mm)

(1) - DO NOT machine valves; hand lap only.
(2) - Information not available from manufacturer.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         CYLINDER HEAD SPECIFICATIONS

CYLINDER HEAD SPECIFICATIONS TABLE

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Application                                    Specification

Cylinder Head Height  ........................  5.492-5.515"
Maximum Warpage  ..........................  .039" (1.00 mm)
Valve Seats
  Intake Valve
   Seat Angle .........................................  45

ø

   Seat Width .........................................  (1)
  Exhaust Valve
   Seat Angle .........................................  45

ø

   Seat Width .........................................  (1)
Valve Guides
  Intake Valve
   Valve Guide Installed Height .......................  (2)
   Oil Clearance  ......................  (3) .039" (1.0 mm)
  Exhaust Valve
   Valve Guide Installed Height ......................   (2)
  Valve Stem-to-Guide
   Oil Clearance ......................  (3) .051" (1.30 mm)

(1) - Information not available from manufacturer.
(2) - Valve guide shoulder flush with cylinder head.
(3) - New valve installed in cylinder head. Dial indicator
      used to measure valve rock in guide.

 

 

 

 

 

 

 

Content   ..  75  76  77  78   ..