Volkswagen Golf / Golf Plus. Manual - part 286

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

5.10

Cleaning off excess adhesive sealing

material

– Use of adhesive remover -D 002 000 10- as a cleaning solution

is recommended. Observe the appropriate safety precautions

when performing this work.

– First clean painted surface as much as possible using a dry

cloth. Remove residue using adhesive remover -D 002 000

10- .

General body repairs, exterior - Edition 04.2008

5. Roof edge spoiler    

265

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

6

Protective backing

6.1

Attachment notes for protective backing

Note

♦

Before removal, heat the scuff protection film with a hot air

blower -V.A.G 1416- .

♦

Use only adhesive remover -D 002 000 10- to remove residual

adhesive.

♦

Ensure that the adhesive surfaces are free of dust and grease.

♦

Bond scuff protection film immediately after cleaning.

♦

Pull protective film off only directly prior to installation.

♦

The working temperature is approx. 21 °C.

General body repairs, exterior - Edition 04.2008

266

     Rep. Gr.66 - Exterior equipment

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

6.2

Renewing scuff protection film

Note

Renewing scuff protection films is described only for the left side. The right side is similar.

Removing
– Removing inner seal for front door in area of side member

⇒ page 75

 or inner seal for rear door 

⇒ page 114

– Heat scuff protection film at the font -1- or at the rear -3- using

a hot air blower -V.A.G 1416- and pull scuff protection film from

sill.

Installing
– Clean installation area with adhesive remover -D 002 00 10- .
– Pull off protective film -2-.
– Position scuff protection film at the front -1- or at the rear -3-

on the references points -arrows- and press it smooth using a

plastic blade wrapped in a soft paper towel.

General body repairs, exterior - Edition 04.2008

6. Protective backing    

267

s

p

e

c

t

 t

o

 

th

e

 c

o

rr

e

c

t

n

e

s

s

 

o

f

in

fo

r

m

a

tio

n

 in

 th

is

 d

o

c

um

en

t.

C

o

py

rig

ht b

y

 

V

olk

sw

a

ge

n

 

A

G.

7

Lettering

7.1

Tools

Special tools and workshop equipment required
♦ Hot air blower -V.A.G 1416-

7.2

Installation instructions for lettering and

emblems

Note

♦

Before removal, heat the lettering or the emblem with a hot air

blower -V.A.G 1416- .

♦

Use only adhesive remover -D 002 000 10- to remove residual

adhesive.

♦

Ensure that the adhesive surfaces are free of dust and grease.

♦

Bond lettering or emblem immediately after cleaning.

♦

Pull protective film off only directly prior to installation.

♦

The working temperature is approx. 21 °C.

General body repairs, exterior - Edition 04.2008

268

     Rep. Gr.66 - Exterior equipment