Nissan Versa Sedan. Instruction - part 653

PWC-34

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW MOTOR

NO

>> Repair or replace harness.

REAR LH
REAR LH : Component Function Check

INFOID:0000000009269437

1.

CHECK FUNCTION

Check rear power window motor LH operation with power window main switch or rear power window switch

LH.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Refer to 

PWC-34, "REAR LH : Diagnosis Procedure"

.

REAR LH : Diagnosis Procedure

INFOID:0000000009269438

Regarding Wiring Diagram information, refer to 

PWC-14, "Wiring Diagram"

.

1.

CHECK REAR POWER WINDOW MOTOR LH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear power window motor LH connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window motor LH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window motor LH.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW MOTOR LH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect rear power window switch LH connector.

3. Check continuity between rear power window switch LH harness connector and rear power window motor

LH harness connector.

4. Check continuity between rear power window switch LH connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window switch LH. Refer to 

PWC-54, "Removal and Installation"

.

(+)

(-)

Condition

Voltage (V)

(Approx.)

Rear power window motor LH

Connector

Terminal 

D204

1

Ground

Rear power win-
dow switch LH

NEUTRAL

0

UP

Battery voltage

2

NEUTRAL

0

DOWN

Battery voltage

Rear power window switch LH

Rear power window motor LH

Continuity

Connector

Terminal

Connector

Terminal

D203

4

D204

2

Yes

5

1

Rear power window switch LH

Ground

Continuity

Connector

Terminal

D203

4

No

5

POWER WINDOW MOTOR

PWC-35

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

NO

>> Repair or replace harness.

REAR RH
REAR RH : Component Function Check

INFOID:0000000009269439

1.

 CHECK FUNCTION

Check rear power window motor RH operation with power window main switch or rear power window switch

RH.
Is the inspection result normal?

YES

>> Inspection End.

NO

>> Refer to 

PWC-35, "REAR RH : Diagnosis Procedure"

.

REAR RH : Diagnosis Procedure

INFOID:0000000009269440

Regarding Wiring Diagram information, refer to 

PWC-14, "Wiring Diagram"

.

1.

CHECK REAR POWER WINDOW MOTOR RH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect rear power window motor RH connector.

3. Turn ignition switch ON.

4. Check voltage between rear power window motor RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window motor RH.

NO

>> GO TO 2.

2.

CHECK REAR POWER WINDOW MOTOR RH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect rear power window switch RH connector.

3. Check continuity between rear power window switch RH harness connector and rear power window motor

RH harness connector.

4. Check continuity between rear power window switch RH harness connector and ground.

Is the inspection result normal?

YES

>> Replace rear power window switch RH. Refer to 

PWC-54, "Removal and Installation"

.

(+)

(-)

Condition

Voltage (V)

(Approx.)

Rear power window motor RH

Connector

Terminal 

D304

1

Ground

Rear power window 
switch RH 

NEUTRAL

0

UP

Battery voltage

2

NEUTRAL

0

DOWN

Battery voltage

Rear power window switch RH

Rear power window motor RH

Continuity

Connector

Terminal

Connector

Terminal

D303

4

D304

2

Yes

5

1

Rear power window switch RH

Ground

Continuity

Connector

Terminal

D303

4

No

5

PWC-36

< DTC/CIRCUIT DIAGNOSIS >

POWER WINDOW MOTOR

NO

>> Repair or replace harness.

DOOR SWITCH

PWC-37

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

PWC

N

O

P

DOOR SWITCH

Description

INFOID:0000000009541437

Detects door open/close condition and transmits the signal to BCM.

Component Function Check

INFOID:0000000009541438

1.

 CHECK FRONT DOOR SWITCH INPUT SIGNAL

Check (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA MONITOR” mode with CONSULT. Refer to 

BCS-26,

"RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)"

 or 

BCS-26, "RETAINED PWR : CONSULT

Function (BCM - RETAINED PWR)"

.

Is the inspection result normal?

YES

>> Front door switch circuit is OK.

NO

>> Refer to 

PWC-37, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009541439

Regarding Wiring Diagram information, refer to 

PWC-14, "Wiring Diagram"

.

1.

 CHECK HARNESS CONTINUITY

Check voltage between BCM connector and ground.

Is the measurement value within the specification?

YES

>> Replace BCM. Refer to 

BCS-69, "Removal and Installation"

 or 

BCS-122, "Removal and Installa-

tion"

.

NO

>> GO TO 2

2.

 CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect BCM and front door switch.

3. Check continuity between BCM connector and front door switch connector.

Monitor item

Condition

DOOR SW-DR

OPEN

: ON

CLOSE

: OFF

DOOR SW-AS

OPEN

: ON

CLOSE

: OFF

Terminals

Door condition

Voltage (V)

(Approx.)

(+)

(–)

BCM

 connector

Terminal 

M18 (without Intelli-

gent Key system)

12

Ground

Front door RH

OPEN

0

CLOSE

Battery voltage

M19 (without Intelli-

gent Key system)

47

Front door LH

OPEN

0

CLOSE

Battery voltage

M100 (with Intelli-

gent Key system)

45

Ground

Front door RH

OPEN

0

CLOSE

Battery voltage

M100 (with Intelli-

gent Key system)

47

Front door LH

OPEN

0

CLOSE

Battery voltage