Nissan Versa Sedan. Instruction - part 428

HIGH-MOUNTED STOP LAMP

EXL-113

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

Removal

1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise.
3. Release high-mounted stop lamp pawls and remove high-mounted stop lamp housing.

Installation

Installation is in the reverse order of removal.

Bulb Replacement

INFOID:0000000009269686

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-

vent damage to the bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

HIGH-MOUNTED STOP LAMP BULB - REAR SPOILER

The high-mounted stop lamp bulb is a LED and is integrated into the high-mounted stop lamp and is serviced

as an assembly. Refer to 

EXL-112, "Removal and Installation"

.

HIGH-MOUNTED STOP LAMP BULB - PARCEL SHELF

Removal

1. Fully open trunk lid assembly.
2. Rotate the bulb socket counterclockwise and remove.
3. Remove the bulb from the bulb socket.

Installation

Installation is in the reverse order of removal.

EXL-114

< REMOVAL AND INSTALLATION >

LICENSE PLATE LAMP

LICENSE PLATE LAMP

Exploded View

INFOID:0000000009269687

Removal and Installation

INFOID:0000000009269688

REMOVAL

1. While pressing the license plate lamp housing pawl toward the right, pull the housing downward and

remove.

2. Rotate the bulb socket counterclockwise and remove.
3. Remove the license plate lamp.

INSTALLATION

Installation is in the reverse order of removal.

Bulb Replacement

INFOID:0000000009269689

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-

tion.

• After installing the bulb, install the back cover and the bulb socket securely for watertightness.

• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-

vent damage to the bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

LICENSE PLATE LAMP BULB

Removal

1. Remove the license plate lamp. Refer to 

EXL-114, "Removal and Installation"

.

2. Remove the bulb from the socket.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing the bulb, install the bulb socket securely for watertightness.

1.

License plate lamp

2.

License plate lamp bulb

JMLIA2055ZZ

SERVICE DATA AND SPECIFICATIONS (SDS)

EXL-115

< SERVICE DATA AND SPECIFICATIONS (SDS) 

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Bulb Specifications

INFOID:0000000009269690

*: Always check with the Parts Department for the latest parts information.

Item

Wattage (W)*

Front combination lamp

High beam

60

Low beam

55

Turn signal/Park lamp

28/8

Side marker lamp

5

Front fog lamp (if equipped)

55

Rear combination lamp

Stop/Tail lamp

21/5

Turn signal lamp

21

Back-up lamp

21

License plate lamp

5

High-mounted stop lamp

16

EXT-1

BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY

C

D

E

F

G

H

I

J

L

M

SECTION 

EXT

A

B

EXT

N

O

P

CONTENTS

EXTERIOR

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

2

Precaution for Procedure without Cowl Top Cover ......

2

Precaution for Work  ..................................................

2

PREPARATION ............................................

4

PREPARATION ...................................................

4

Special Service Tools ..............................................

4

Commercial Service Tools .......................................

4

CLIP LIST  ............................................................

5

Descriptions for Clips  ................................................

5

SYMPTOM DIAGNOSIS  ...............................

9

SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ................................................................

9

Work Flow  .................................................................

9

Generic Squeak and Rattle Troubleshooting  ..........

11

Diagnostic Worksheet  .............................................

13

REMOVAL AND INSTALLATION ...............

15

FRONT BUMPER  ...............................................

15

Exploded View  ........................................................

15

Removal and Installation .........................................

16

UNDER COVER  .................................................

18

Exploded View  ........................................................

18

Removal and Installation .........................................

19

REAR BUMPER  ................................................

20

Exploded View .........................................................

20

Removal and Installation  .........................................

20

FRONT GRILLE  ................................................

23

Exploded View .........................................................

23

Removal and Installation  .........................................

23

COWL TOP  .......................................................

24

Exploded View .........................................................

24

Removal and Installation  .........................................

24

FENDER PROTECTOR  ....................................

26

Exploded View .........................................................

26

Removal and Installation  .........................................

26

ROOF SIDE MOLDING  .....................................

27

Exploded View .........................................................

27

Removal and Installation  .........................................

27

DOOR OUTSIDE MOLDING  .............................

29

Exploded View .........................................................

29

Removal and Installation  .........................................

29

TRUNK LID FINISHER ......................................

30

Exploded View .........................................................

30

Removal and Installation  .........................................

30

DOOR PARTING SEAL  ....................................

31

Exploded View .........................................................

31

Removal and Installation  .........................................

31

REAR SPOILER ................................................

33

Exploded View .........................................................

33

Removal and Installation  .........................................

33