Nissan Versa Sedan. Instruction - part 425

 

  Index      Nissan     Nissan Versa Sedan (2014 year) - Service and Repair Instruction

 

Search            copyright infringement  

 

 

 

 

 

 

 

  

 

Content   ..  423  424  425  426   ..

 

 

Nissan Versa Sedan. Instruction - part 425

 

 

FRONT FOG LAMP AIMING ADJUSTMENT

EXL-101

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

FRONT FOG LAMP AIMING ADJUSTMENT

Inspection

INFOID:0000000009269667

PREPARATION BEFORE ADJUSTING

CAUTION:

Do not use organic solvent (thinner, gasoline etc.)

NOTE:

• For details, refer to the regulations in your own country.

• Perform aiming if the vehicle front body has been repaired and/or the front fog lamp has been replaced.

• Before performing aiming adjustment, check the following.

• Keep all tires inflated to correct pressure.

• Place vehicle on level ground.

• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and

tools). Have the driver or equivalent weight placed in driver seat.

• Adjust aiming in the vertical direction by turning the adjusting screw.

• When performing adjustment, if necessary, cover the headlamps and opposite fog lamp.

AIMING ADJUSTMENT SCREW

• Turn the aiming adjusting screw using a suitable tool to aim the fog

lamp.

A: UP

B: DOWN

• For the position and direction of the adjusting screw refer to the fig-

ure as shown.

Aiming Adjustment Procedure

INFOID:0000000009269668

1. Screen placement.

NOTE:

• Place the screen perpendicular to the level road.

• Position the vehicle facing the screen with 10 m (32.8 ft) between the front fog lamp center and the

screen.

2. Start the engine. Illuminate the front fog lamp.

CAUTION:

Do not cover the lens surface with a tape etc. The lens are made of resin.

3. Adjust the cutoff line height (A) with the aiming adjustment

screw so that the distance (X) between the horizontal center line

of front fog lamp (H) and (A) becomes 200 mm (7.87 in).

Front fog lamp light distribution on the screen

• A :Cutoff line 

• B :High illuminance

• H :Horizontal center line of front fog lamp

• V :Vertical center line of front fog lamp

• X :Cutoff line height

JMLIA2040ZZ

JPLIA0008ZZ

EXL-102

< REMOVAL AND INSTALLATION >

FRONT COMBINATION LAMP

REMOVAL AND INSTALLATION

FRONT COMBINATION LAMP

Exploded View

INFOID:0000000009269669

Removal and Installation

INFOID:0000000009269670

REMOVAL

1. Disconnect the battery negative terminal. Refer to 

PG-63, "Removal and Installation"

.

2. Remove front bumper fascia. Refer to 

EXT-16, "Removal and Installation"

.

3. Remove the front combination lamp bolts.
4. Pull the headlamp assembly forward slightly. 
5. Disconnect the harness connectors from the front combination lamp and remove.

INSTALLATION

Installation is in the reverse order of removal.

NOTE:

After installation, perform headlamp aiming adjustment procedure. Refer to 

EXL-99, "Aiming Adjustment Pro-

cedure"

.

Bulb Replacement

INFOID:0000000009269671

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-

tion.

• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-

vent damage to the bulb.

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

HEADLAMP BULB

Removal

1. Disconnect the harness connector from the headlamp bulb.
2. Remove the cover.

1.

Front combination lamp (LH)

JMLIA2041GB

FRONT COMBINATION LAMP

EXL-103

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

M

A

B

EXL

N

O

P

3. Remove the retaining spring lock and the bulb from the front combination lamp.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing the bulb, install the bulb socket securely for watertightness.

PARKING LAMP BULB

Removal

1. Rotate the bulb socket counterclockwise and remove.
2. Remove the bulb from the bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing the bulb, install the bulb socket securely for watertightness.

FRONT TURN SIGNAL LAMP BULB

Removal

1. Rotate the bulb socket counterclockwise and remove.
2. Remove the bulb from the bulb socket.

Installation

Installation is in the reverse order of removal.

CAUTION:

After installing the bulb, install the bulb socket securely for watertightness.

Disassembly and Assembly

INFOID:0000000009269672

Exploded View

WARNING:

Do not touch bulb with your hand while it is on or right after being turned off. Burning may result.

CAUTION:

• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-

tion.

• After installing the bulb, install cover and the bulb socket securely for watertightness.

• Do not touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-

vent damage to the bulb.

1.

Front combination lamp

2.

Parking lamp bulb

3.

Parking lamp bulb socket

4.

Cover

5.

Halogen bulb 

6.

Front turn signal lamp bulb socket

7.

Front turn signal lamp bulb

8.

Retaining spring

JMLIA2042ZZ

EXL-104

< REMOVAL AND INSTALLATION >

FRONT COMBINATION LAMP

• Do not leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect

the performance of lamp. When replacing bulb, be sure to replace it with new one.

DISASSEMBLY

1. Remove the cover.
2. Remove the retaining spring lock and bulb.
3. Rotate the parking lamp bulb socket counterclockwise and remove.
4. Remove the bulb from the parking lamp bulb socket.
5. Rotate the front turn signal lamp bulb socket counterclockwise and remove.
6. Remove the bulb from the front turn signal lamp bulb socket.

ASSEMBLY

Assembly is in the reverse order of disassembly.

 

 

 

 

 

 

 

Content   ..  423  424  425  426   ..