Nissan Versa Sedan. Instruction - part 215

DLK-178

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

TRUNK LID LOCK

TRUNK LID OPENER CABLE : Removal and Installation

INFOID:0000000009268878

REMOVAL

1. Remove trunk lid striker. Refer to 

DLK-160, "TRUNK LID STRIKER : Removal and Installation"

.

2. Remove trunk side finisher (LH). Refer to 

INT-33, "TRUNK SIDE FINISHER : Removal and Installation"

.

3. Remove rear seat cushion. Refer to 

SE-23, "Removal and Installation - Seat Cushion Assembly"

.

4. Remove center pillar lower finisher (LH). Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER :

Removal and Installation"

.

5. Remove trunk lid opener handle. Refer to 

DLK-177, "TRUNK LID OPENER HANDLE : Removal and

Installation"

.

6. Release pawl using a suitable tool (A) and open the harness

clip.

: Pawl

7. Remove trunk lid opener cable.

CAUTION:

Use care not to damage the trunk lid opener cable when removing.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check trunk lid open/close, lock/unlock operation.

• After installation, perform the trunk lid adjustment procedure. Refer to 

DLK-159, "TRUNK LID

ASSEMBLY : Adjustment"

.

EMERGENCY LEVER
EMERGENCY LEVER : Removal and Installation

INFOID:0000000009268879

Removal

1. Release the pawls using a suitable tool and remove emergency

release handle (1) from trunk lid assembly.

: Pawl

2. Disconnect emergency release handle cable (2) from trunk lid

lock assembly (3).

AWJIA0737ZZ

ALKIA2310ZZ

FUEL FILLER LID OPENER

DLK-179

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FUEL FILLER LID OPENER

Exploded View

INFOID:0000000009268880

FUEL FILLER LID
FUEL FILLER LID : Removal and Installation

INFOID:0000000009268881

REMOVAL 

1. Fully open fuel filler lid. 
2. Remove fuel cap pin (1).

3. Remove fuel filler lid screws and fuel filler lid.

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

1.

Fuel filler lid opener cable

2.

Spring

3.

Fuel filler lid assembly

4.

Bumper rubber

5.

Fuel filler lid lock assembly

6.

Cable protector

Clip

JMKIA8174ZZ

JMKIA8137ZZ

DLK-180

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

FUEL FILLER LID OPENER

FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and Installation

INFOID:0000000009268882

REMOVAL 

1. Remove hood and fuel filler handle assembly bolts (A).

2. Disconnect fuel filler lid opener cable (2) by pulling downward

and then sliding cable end to the side to remove from hood and

fuel filler handle assembly (1).

3. Remove dash side finisher (LH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installation"

.

4. Remove center pillar lower finisher (LH). Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER :

Removal and Installation"

.

5. Remove trunk side finisher (LH). Refer to 

INT-35, "Removal and Installation"

.

6. Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to 

DLK-181, "FUEL FILLER LID

LOCK : Removal and Installation"

.

7. Disengage each harness protector (1), and then remove fuel

filler lid opener cable (2).

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER LID LOCK

JMKIA7998ZZ

JMKIA7999ZZ

JMKIA5720ZZ

FUEL FILLER LID OPENER

DLK-181

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

FUEL FILLER LID LOCK : Removal and Installation

INFOID:0000000009268883

REMOVAL 

1. Fully open fuel filler lid.
2. Remove trunk side finisher (LH). Refer to 

INT-33, "TRUNK SIDE FINISHER : Removal and Installation"

.

3. Release pawls (A) and remove fuel filler lid lock assembly (1)

from opening.

CAUTION:

Be careful not to damage gasket (2) when removing.

4. Disconnect fuel filler lid opener cable (1) by pulling downward

and then sliding cable end to the side to remove from fuel filler

lid lock assembly (2).

INSTALLATION 

Installation is in the reverse order of removal.

CAUTION:

After installation, check fuel filler lid assembly open/close, lock/unlock operation.

JMKIA8138ZZ

JMKIA8139ZZ