Nissan Versa Sedan. Instruction - part 211

DLK-162

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

TRUNK LID

3. Apply a torsion bar wrench (A) to torsion bar (1) and lift torsion

bar to remove it.

NOTE:

For torsion bar wrench, refer to the figure.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

Check trunk lid open/close operation after installation.

TRUNK LID WEATHER-STRIP
TRUNK LID WEATHER-STRIP : Removal and Installation

INFOID:0000000009268861

REMOVAL

Remove trunk lid weatherstrip from the trunk lid opening.

CAUTION:

Do not pull excessively on weatherstrip.

INSTALLATION

1. Working from the upper section, align weatherstrip center mark

(A) with vehicle center mark (B) and install weatherstrip onto the

vehicle.

: Front

JMKIA8128ZZ

PIIB3774J

JMKIA8129ZZ

TRUNK LID

DLK-163

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

2. Align the connecting point (B) of weatherstrip (2) to the center

(A) of striker (1) and install as shown.

3. Make sure entire weatherstrip is firmly seated.

NOTE:

Check that weatherstrip fits tightly all around the opening, especially in each corner and along the luggage

rear plate.

JMKIA8130ZZ

DLK-164

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

HOOD LOCK

HOOD LOCK

Exploded View

INFOID:0000000009268862

HOOD LOCK
HOOD LOCK : Removal and Installation

INFOID:0000000009268863

REMOVAL

1. Remove hood lock assembly bolts and hood lock assembly. 
2. Disconnect hood lock control cable assembly (2) from hood lock

assembly (1).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Be careful not to bend the cable too much, keep the radius 100 mm (3.94 in) or more.

• Check that hood lock control cable is properly engaged with hood lock.

1.

Secondary latch

2.

Hood lock assembly

3.

Hood lock control cable assembly

Clip

AWKIA1892GB

JMKIA7997ZZ

HOOD LOCK

DLK-165

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

• After installation, perform hood adjustment procedure. Refer to 

DLK-140, "HOOD ASSEMBLY :

Adjustment"

.

• After adjusting, perform hood lock control inspection. Refer to 

DLK-166, "Inspection"

.

HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation

INFOID:0000000009268864

REMOVAL

1. Disconnect hood lock control cable assembly from hood lock assembly. Refer to 

DLK-164, "HOOD LOCK

: Removal and Installation"

.

2. Remove fender protector (LH). Refer to 

EXT-26, "Removal and Installation"

.

3. Release hood lock control cable clips.
4. Remove hood lock/fuel filler door release handle assembly bolts

(A).

5. Disconnect hood lock control cable assembly from hood lock/

fuel filler door release handle assembly.

6. Remove dash side finisher (LH). Refer to 

INT-21, "DASH SIDE FINISHER : Removal and Installation"

7. Remove grommet on the lower dash and pull the hood lock control cable into the passenger compart-

ment.

CAUTION:

While pulling, be careful not to damage (peel) the outside of the hood lock control cable.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Be careful not to bend cable too much, keep the radius 100 mm (3.94 in) or more.

• Check that cable is not offset from the positioning grommet,

and apply the sealant to the grommet (at * mark).

• Check that hood lock control cable is properly engaged with hood lock.

• Perform hood adjustment procedure. Refer to 

DLK-140, "HOOD ASSEMBLY : Adjustment"

.

• After installation, perform hood lock inspection. Refer to 

DLK-166, "Inspection"

.

HOOD LOCK SECONDARY CONTROL
HOOD LOCK SECONDARY CONTROL : Removal and Installation

INFOID:0000000009268865

REMOVAL

1. Remove radiator upper seal clips and then remove upper clip from radiator side seal (RH). Refer to 

DLK-

143, "Exploded View"

.

2. Remove hood lock secondary control nuts and hood lock secondary control. 

JMKIA7998ZZ

PIIB5801E