Nissan Versa Sedan. Instruction - part 209

DLK-154

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

REAR DOOR

2. Disconnect the harness connector (A) from rear door.

3. Remove door check link bolts from body.
4. Remove door hinge nuts (door side) and rear door assembly.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Apply anticorrosive agent onto the hinge mating surface.

• After installation, check rear door open/close, lock/unlock operation.

• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose

grease.

• After installation, perform the rear door adjustment procedure. Refer to 

DLK-155, "DOOR ASSEMBLY

: Adjustment"

.

• After adjusting, apply touch-up paint (body color) onto the head of door hinge nuts.

JMKIA8084ZZ

REAR DOOR

DLK-155

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR ASSEMBLY : Adjustment

INFOID:0000000009268851

Check the clearance and surface height between rear door and each part by visually and touching. 

If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-

dure.

Unit: mm (in)

ADJUSTMENT PROCEDURE

1. Remove center pillar lower finisher. Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER : Removal

and Installation"

.

1.

Front fender

2.

Front door 

3.

Rear door

4.

Body side outer

5.

Door striker

6.

Striker bolt

7.

Front door hinge

8.

Rear door hinge (upper)

9.

Rear door hinge (lower)

JMKIA8146GB

Section

Measurement

Standard

A – A

Clearance

4.6 

± 1.0 (0.18 ± 0.04)

Surface height

0.0 

± 1.0 (0.0 ± 0.04)

B – B

Clearance

4.6 

± 2.0 (0.18 ± 0.08)

Surface height

0.0 

± 1.5 (0.0 ± 0.06)

C – C

Clearance

4.6 

± 1.0 (0.18 ± 0.04)

Surface height

0.0 

± 1.0 (0.0 ± 0.04)

DLK-156

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

REAR DOOR

2. Loosen door hinge nuts on door side.
3. Adjust the surface height of rear door according to the specifications provided.
4. Temporarily tighten door hinge nuts on door side.
5. Loosen door hinge nuts and bolts on body side. 
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. After adjustment tighten bolts and nuts to the specified torque.

CAUTION:

• Apply touch-up paint (body color) onto the head of hinge bolts and nuts.

• Check door hinge rotating point for poor lubrication. If necessary, apply a suitable multi-purpose

grease.

8. Install center pillar lower finisher. Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER : Removal and

Installation"

.

DOOR STRIKER ADJUSTMENT

Adjust door striker so that it becomes parallel with door lock insertion direction.

DOOR STRIKER
DOOR STRIKER : Removal and Installation

INFOID:0000000009268852

REMOVAL

Remove striker bolts and rear door striker.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check rear door open/close, lock/unlock operation.

• After installation, perform the rear door adjustment procedure. Refer to 

DLK-155, "DOOR ASSEMBLY

: Adjustment"

.

DOOR HINGE
DOOR HINGE : Removal and Installation

INFOID:0000000009268853

CAUTION:

• Use two people when removing or installing rear door due to its heavy weight.

• When removing and installing rear door assembly, support door using a suitable tool.

• Use shop cloths to protect surrounding components from damage during removal and installation of

front door assembly.

REMOVAL

1. Remove rear door assembly. Refer to 

DLK-153, "DOOR ASSEMBLY : Removal and Installation"

.

2. Remove center pillar lower finisher. Refer to 

INT-23, "CENTER PILLAR LOWER FINISHER : Removal

and Installation"

.

3. Remove rear door hinge bolts and nuts (body side) and remove rear door hinge.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Apply anticorrosive agent onto the hinge mating surface.

• After installation, check rear door open/close, lock/unlock operation.

• After installation, perform the rear door adjustment procedure. Refer to 

DLK-155, "DOOR ASSEMBLY

: Adjustment"

.

• After adjusting, apply the touch-up paint (body color) onto the head of door hinge nuts.

REAR DOOR

DLK-157

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

• Check door hinge rotating point for poor lubrication. If neces-

sary, apply a suitable multi-purpose grease.

DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation

INFOID:0000000009268854

REMOVAL

1. Fully close the rear door window.
2. Remove rear door finisher. Refer to 

INT-15, "Removal and Installation"

.

3. Remove rear door speaker bolts (if equipped).
4. Disconnect harness connector and remove rear door speaker (if equipped).
5. Remove sealing screen (lower) if vehicle is not equipped with rear door speakers.
6. Remove door check link bolts from body.
7. Remove door check link bolts from door panel.
8. Remove door check link (1) through the hole in rear door panel

(2).

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• After installation, check rear door open/close, lock/unlock operation.

• Check door check link rotating point for poor lubrication. If

necessary, apply a suitable multi-purpose grease.

JMKIA8072ZZ

JMKIA8085ZZ

JMKIA8074ZZ