Nissan Versa Sedan. Instruction - part 115

DIAGNOSIS AND REPAIR WORK FLOW

BRC-53

< BASIC INSPECTION >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Check ABS and brake warning lamps, and VDC OFF and SLIP indicator lamps operation. Refer to 

MWI-10,

"METER SYSTEM : System Description"

 (type A) or 

MWI-60, "METER SYSTEM : System Description"

 (type

B).
Is ON/OFF timing normal?

YES

>> GO TO 5.

NO

>> Perform warning lamp diagnosis. Refer to 

BRC-92, "Component Function Check"

 (ABS warning

lamp), 

BRC-93, "Component Function Check"

 (brake warning lamp), 

BRC-94, "Component Func-

tion Check"

 (VDC OFF indicator lamp) or 

BRC-95, "Component Function Check"

 (SLIP indicator

lamp).

5.

PERFORM DIAGNOSIS APPLICABLE TO THE SYMPTOM

Perform diagnosis applicable to the symptom. Refer to 

BRC-96, "Symptom Table"

.

>> GO TO 6.

6.

FINAL CHECK

Perform self diagnostic result again, and check that the malfunction is repaired. After checking, erase the self

diagnosis memory. Refer to 

BRC-32, "CONSULT Function (ABS)"

.

>> Inspection End.

Diagnostic Work Sheet

INFOID:0000000009267607

SFIA3265E

BRC-54

< BASIC INSPECTION >

[VDC/TCS/ABS]

ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELECTRIC 

UNIT (CONTROL UNIT)

ADDITIONAL SERVICE WHEN REPLACING ABS ACTUATOR AND ELEC-
TRIC UNIT (CONTROL UNIT)

Description

INFOID:0000000009267608

After replacing the ABS actuator and electric unit (control unit), perform the neutral position adjustment for the

steering angle sensor. Refer to 

BRC-55, "Work Procedure"

.

Work Procedure

INFOID:0000000009267609

1.

PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR

Perform the neutral position adjustment for the steering angle sensor.

>> Refer to 

BRC-55, "Work Procedure"

.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

BRC-55

< BASIC INSPECTION >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Description

INFOID:0000000009267610

Refer to the table below to determine if adjustment of steering angle sensor neutral position is required.

×: Required –: Not required

Work Procedure

INFOID:0000000009267611

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

CAUTION:

To adjust neutral position of steering angle sensor, make sure to use CONSULT.

(Adjustment cannot be done without CONSULT).

1.

ALIGN THE VEHICLE STATUS

Stop vehicle with front wheels in straight-ahead position.

>> GO TO 2

2.

PERFORM THE NEUTRAL POSITION ADJUSTMENT FOR THE STEERING ANGLE SENSOR

1. On the CONSULT screen, touch “WORK SUPPORT” and “ST ANG SEN ADJUSTMENT” in order.

2. Touch “START”.

CAUTION:

Do not touch steering wheel while adjusting steering angle sensor.

3. After approximately 10 seconds, touch “END”.

NOTE:

After approximately 60 seconds, it ends automatically.

4. Turn ignition switch OFF, then turn it ON again.

CAUTION:

Be sure to perform above operation.

>> GO TO 3

3.

CHECK DATA MONITOR

1. Run vehicle with front wheels in straight-ahead position, then stop.

2. Select “DATA MONITOR”. Then make sure “STR ANGLE SIG” is within 0

±2.5°.

Is the steering angle within the specified range?

YES

>> GO TO 4

NO

>> Perform the neutral position adjustment for the steering angle sensor again, GO TO 1

4.

ERASE THE SELF-DIAGNOSIS MEMORY

Erase the self-diagnosis memory of the ABS actuator and electric unit (control unit) and ECM.

• ABS actuator and electric unit (control unit): Refer to 

BRC-32, "CONSULT Function (ABS)"

.

Situation

Adjustment of steering angle sensor neutral position

Removing/Installing ABS actuator and electric unit (control unit)

—

Replacing ABS actuator and electric unit (control unit)

×

Removing/Installing steering angle sensor

×

Replacing steering angle sensor

×

Removing/Installing steering components

×

Replacing steering components

×

Removing/Installing suspension components

×

Replacing suspension components

×

Change tires to new ones

—

Tire rotation

—

Adjusting wheel alignment

×

BRC-56

< BASIC INSPECTION >

[VDC/TCS/ABS]

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

• ECM: Refer to 

EC-61, "CONSULT Function"

.

Are the memories erased?

YES

>> Inspection End

NO

>> Check the items indicated by the self-diagnosis.