Nissan X-Trail 32. Instruction - part 2021

TM-42

< UNIT REMOVAL AND INSTALLATION >

[6MT: RS6F94R]

TRANSAXLE ASSEMBLY

• When installing transaxle assembly, never bring input shaft into contact with clutch cover.
• When installing the transaxle assembly to the engine assembly,

install mounting bolts following the standard below, tighten bolts to
the specified torque. For each tightening torque, refer to 

TM-41,

"Exploded View"

.

• Perform inspection after installation. Refer to 

TM-42, "Inspection"

.

Inspection

INFOID:0000000010842461

INSPECTION AFTER INSTALLATION

Check the oil leakage and the oil level. Refer to 

TM-27, "Inspection"

.

Bolt symbol

Quantity

3

6

Bolt length

“

” mm (in)

60 (2.36)

50 (1.97)

Insertion direction

Transaxle to engine

Engine to transaxle

JPDIC0837ZZ

TRANSAXLE ASSEMBLY

TM-43

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F94R]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

UNIT DISASSEMBLY AND ASSEMBLY

TRANSAXLE ASSEMBLY

Exploded View

INFOID:0000000010842462

CASE AND HOUSING

Filler plug

Gasket

Transaxle case

Bushing

Snap ring

Oil channel

Oil gutter

Position switch

Bracket

Differential side oil seal

Magnet

Drain plug

Input shaft oil seal

Clutch housing

2 way connector

Plug

Pinion shaft

Pinion gear

: N·m (kg-m, in-lb)

JPDIC0437GB

TM-44

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F94R]

TRANSAXLE ASSEMBLY

SHAFT AND GEAR

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

: Select with proper thickness.

: Apply Genuine Liquid Gasket, Three Bond 1215 or an equivalent.

Input shaft front bearing

Input shaft

3rd input gear

Spacer

Snap ring

3rd baulk ring

3rd-4th coupling sleeve

3rd-4th synchronizer hub

Insert key

4th baulk ring

4th input gear

5th input gear

5th baulk ring

5th-6th coupling sleeve

5th-6th synchronizer hub

6th baulk ring

Needle bearing 

6th input gear

Input shaft rear bearing

First step

Final step

: N·m (kg-m, ft-lb)

: Always replace after every disassembly.

JPDIC0407GB

TRANSAXLE ASSEMBLY

TM-45

< UNIT DISASSEMBLY AND ASSEMBLY >

[6MT: RS6F94R]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

: Apply gear oil.

: Replace the parts as a set.

Mainshaft front bearing outer 
race

Mainshaft front bearing inner race

Mainshaft

1st main gear

1st inner baulk ring

1st synchronizer cone

1st outer baulk ring

1st-2nd coupling sleeve

Insert key

1st-2nd synchronizer hub

2nd outer baulk ring

2nd synchronizer cone

2nd inner baulk ring

2nd main gear

Bushing

3rd main gear

Mainshaft adjusting shim

4th main gear

5th main gear

6th main gear

Mainshaft rear bearing inner race

Mainshaft rear bearing outer race

Snap ring

Mainshaft rear bearing adjusting 
shim

: Always replace after every disassembly.

: Select with proper thickness.

: Apply gear oil.

: Replace the parts as a set.

SFIA3293E