Mercedes-Benz Sprinter / Dodge Sprinter. Service manual - part 539

 

  Index      Mercedes     Mercedes-Benz Sprinter / Dodge Sprinter - service and repair manual 2006 year

 

Search            copyright infringement  

 

 

 

 

 

 

 



 

 

Content   ..  537  538  539  540   ..

 

 

Mercedes-Benz Sprinter / Dodge Sprinter. Service manual - part 539

 

 

Symptom:

ABS LF SENSOR MESSAGE

When Monitored and Set Condition:

ABS LF SENSOR MESSAGE

When Monitored:

Valid ABS CAN messages received at least once and the CAN Bus

circuit, ABS CAN Message Missing, ABS CAN Message Incorrect are not active

Set Condition:

ABS signal

9Wheel Speed Front Left9 not valid or ABS has detected a

sensor failure.

POSSIBLE CAUSES

CAN BUS CIRCUIT DTC PRESENT

ABS DTCS PRESENT

ABS CONTROL MODULE - ABS LF SENSOR MESSAGE

TCM - ABS LF SENSOR MESSAGE

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTCs. Check and repair all engine DTCs prior to

performing transmission symptom diagnostics.
With the DRBIII

t, read and record all Transmission DTCs.

NOTE: Check connectors - Clean/repair as necessary. Poor pin to terminal
connections can set DTCs.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Most DTCs set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for any Technical Service Bulletins that may apply.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

Ignition on, engine not running.
With the DRBIII

t, read Transmission DTCs.

NOTE: If the DTC, CAN BUS CIRCUIT, is present, perform diagnostics on
that symptom first.
Is the DTC, CAN BUS CIRCUIT, present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 3

38

TRANSMISSION - NAG1

TEST

ACTION

APPLICABILITY

3

Ignition on, engine not running.
With the DRBIII

t, read ABS DTCs.

Are there any ABS DTCs present?

All

Yes

→ Refer to the BRAKE category and perform the appropriate

symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Turn the ignition off to the lock position.
Replace the ABS Control Module per the Service Information.
With the DRBIII

t, erase Transmission DTCs.

Road test the Vehicle.
With the DRBIII

t, read Transmission DTCs.

Does the DTC, ABS LF SENSOR MESSAGE, reset?

All

Yes

→ Replace the Transmission Control Module.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Test complete.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

39

TRANSMISSION - NAG1

ABS LF SENSOR MESSAGE —

Continued

Symptom:

ABS LR SENSOR MESSAGE

When Monitored and Set Condition:

ABS LR SENSOR MESSAGE

When Monitored:

Valid ABS CAN messages received at least once and the CAN Bus

circuit, ABS CAN Message Missing, ABS CAN Message Incorrect are not active

Set Condition:

ABS signal

9wheel speed rear left9 not valid or ABS has detected a sensor

failure.

POSSIBLE CAUSES

CAN BUS CIRCUIT DTC PRESENT

ABS DTCS PRESENT

ABS CONTROL MODULE - ABS LR SENSOR MESSAGE

TCM - ABS LR SENSOR MESSAGE

TEST

ACTION

APPLICABILITY

1

NOTE: Low fluid level can be the cause of many transmission problems. If
the fluid level is low locate and repair the leak then check and adjust the
fluid level per the service information.
NOTE: Always perform diagnostics with a fully charged battery to avoid
false symptoms.
With the DRBIII

t, read the engine DTCs. Check and repair all engine DTCs prior to

performing transmission symptom diagnostics.
With the DRBIII

t, read and record all Transmission DTCs.

NOTE: Check connectors - Clean/repair as necessary. Poor pin to terminal
connections can set DTCs.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Repair as necessary.
Most DTCs set on start up but some must be set by driving the vehicle such that all
diagnostic monitors have run.
Note: Verify flash level of transmission controller. Some problems are
corrected by software upgrades to the transmission controller.
NOTE: Check for any Technical Service Bulletins that may apply.
Perform this procedure prior to Symptom diagnosis.

All

Continue

Go To

2

2

Ignition on, engine not running.
With the DRBIII

t, read Transmission DTCs.

NOTE: If the DTC, CAN BUS CIRCUIT, is present, perform diagnostics on
that symptom first.
Is the DTC, CAN BUS CIRCUIT, present?

All

Yes

→ Refer to the Transmission category and perform the appropriate

symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 3

40

TRANSMISSION - NAG1

TEST

ACTION

APPLICABILITY

3

Ignition on, engine not running.
With the DRBIII

t, read ABS DTCs.

Are there any ABS DTCs present?

All

Yes

→ Refer to the BRAKE category and perform the appropriate

symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Go To 4

4

Turn the ignition off to the lock position.
Replace the ABS Control Module per the Service Information.
With the DRBIII

t, erase Transmission DTCs.

Road test the Vehicle.
With the DRBIII

t, read Transmission DTCs.

Does the DTC, ABS LR SENSOR MESSAGE, reset?

All

Yes

→ Replace the Transmission Control Module.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

No

→ Test complete.

Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1.

41

TRANSMISSION - NAG1

ABS LR SENSOR MESSAGE —

Continued

 

 

 

 

 

 

 

Content   ..  537  538  539  540   ..