Hyundai Sonata Plug-in Hybrid (2017 year). Manual - part 38
Engine compartment main fuse panel (Hybrid)
Fuse Name
Fuse rating
Protected Component
IG2
30A
IGPM (Fuse - F8/F25/F31/F38/F42)
BLOWER
40A
RLY. 9 (Blower Relay)
2AHB
40A
Integrated Brake Actuation Unit
MULTI
1AHB
40A
Integrated Brake Actuation Unit
FUSE
REAR HEATED
50A
RLY. 12 (Rear Heated Relay)
(TYPE A)
3B+
50A
IGPM (IPS2 (4CH), IPS3 (4CH), Fuse - F28/F29)
5B+
50A
PCM Block (Fuse - F4/F5/F6/F13/F14/F18/F22, Engine Control Relay)
EEWP
60A
Electric Water Pump
1MDPS
80A
MDPS Unit
IG1
40A
IGPM (Fuse - F14/F19/F20/F26/F27/F33/F34/F40/F41/F47/F46)
MULTI
POWER OUTLET
40A
RLY. 10 (Power Outlet Relay)
FUSE
2B+
50A
IGPM (IPS1 (4CH), IPS4 (4CH), IPS5 (4CH), Fuse - F36/F42)
(TYPE B)
1B+
60A
IGPM (Fuse - F1/F2/F10/F13/F17/F18/F23/F24/F30, Power Window Relay)
COOLING FAN
60A
RLY.2 (Cooling Fan Relay)
DEICER
20A
RLY. 6 (Deicer Relay)
FUSE
1OPCU
20A
Electric Oil Pump Unit
7
1HEV ECU
10A
HPCU
7-73
Maintenance
Engine compartment main fuse panel (Hybrid)
Fuse Name
Fuse rating
Protected Component
H/LAMP HI
20A
RLY. 7 (Head Lamp High Relay)
4B+
40A
IGPM (Leak Current Autocut Device Fuse - F15/F16/F21/F22, Fuse - F5/F6/F7/F11/F12)
2EPB
30A
Electric Parking Brake Module
1EPB
30A
Electric Parking Brake Module
HEATED MIRROR
10A
A/C Control Module, Drover/Passenger Power Outside Mirror
3ECU
10A
PCM
2HEV ECU
10A
HPCU
1POWER OUTLET
20A
Cigarette Lighter
FUEL PUMP
20A
Fuel Pump Relay
HORN
20A
Horn Relay, ICM Relay Box (Burglar Alarm Horn Relay)
FUSE
WIPER
30A
Front Wiper (Low) Relay, Front Wiper (High) Relay
2TCU
15A
Transmission Range Switch, Electric Water Pump
3AHB
10A
Integrated Brake Actuation Unit
2POWER OUTLET
20A
Rear Power Outlet
Transmission Range Switch, PCM, Audio, Electro Chromic Mirror, Back-Up Lamp LH/RH,
B/UP LAMP
10A
Rear Curtain Unit
1SENSOR
15A
Oxygen Sensor (Up/Down)
E/R Junction Block (RLY. 2 - Cooling Fan Relay), Mass Air Flow Sensor,
2SENSOR
10A
Oil Control Valve #1/#2, Purge Control Solenoid Valve, Canister Close Valve,
Camshaft Position Sensor #1/#2, Fuel Pump Relay
2ECU
10A
PCM
7-74
Engine compartment main fuse panel (Hybrid)
Fuse Name
Fuse rating
Protected Component
1TCU
10A
PCM
1OPCU
10A
Electric Oil Pump Unit
EWP
10A
Electric Water Pump
FUSE
BATTERY C/FAN
15A
E/R Junction Block (RLY. 5 (Battery C/FAN))
1ECU
20A
PCM
IGN COIL
20A
Ignition Coil #1/#2/#3/#4
AMS
10A
Battery Sensor
7
7-75
Maintenance
Engine compartment main fuse
panel (Plug-in hybrid)
OLF074028
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay name and capacity.
i
Information
Not all fuse panel descriptions in this
manual may be applicable to your
vehicle; the information is accurate at
OLFP075105N
the time of printing. When you inspect
the fuse panel in your vehicle, refer to
the fuse panel label.
7-76
Engine compartment main fuse panel (Plug-in hybrid)
Fuse Name
Fuse rating
Protected Component
IG2
30A
PCB Block (IG2 Relay)
BLOWER
40A
Blower Relay
2AHB
40A
Integrated Brake Actuation Unit, Multipurpose Check Connector
1 AHB
40A
Integrated Brake Actuation Unit, Multipurpose Check Connector
REAR
MULTI FUSE
50A
Rear Heated Relay
HEATED
(TYPE A)
3 B+
50A
IGPM (IPS2 (4CH), IPS3 (4CH), Fuse - STOP LAMP/MODULE 1)
PCM Block (Fuse - WIPER/HORN/BATTERY C/FAN/AMS/TCU 1/ECU 2/FUEL PUMP,
5 B+
50A
Engine Control Relay)
EEWP
60A
Electric Water Pump
MDPS
80A
MDPS Unit
IG1
40A
PCB Block (IG1 Relay)
3 POWER
40A
Power Outlet Relay
OUTLET
2 PTC
50A
PTC Heater 2 Relay
HEATER
1 PTC
MULTI FUSE
50A
PTC Heater 1 Relay
7
HEATER
(TYPE B)
2 B+
50A
IGPM (IPS1 (4CH), IPS4 (4CH), IPS5 (4CH), Fuse - IG3/AMP)
IGPM (Fuse - P/SEAT DRV/P/SEAT PASS/S/HEATER RR/SUNROOF 1/
1 B+
60A
SUNROOF 2/SAFETY POWER WINDOW LH/ SAFETY POWER WINDOW RH/TRUNK,
Power Window Relay)
COOLING
60A
Cooling Fan Relay
FAN
7-77
Maintenance
Engine compartment main fuse panel (Plug-in hybrid)
Fuse Name
Fuse rating
Protected Component
IGPM (Gateway), Instrument Cluster, BMS Control Module (Main/Sub), Battery
2 IG3
10A
Expansion Module Sensor Swtich (Main), Transaxle Range Switch, PCM, HPCU,
Charge Indicator, A/V & Navigation Head Unit
1 IG3
10A
Electric Water Pump (HEV)
OBC
10A
OBC Unit
DEICER
20A
Deicer Relay
1 OPCU
20A
Electric Oil Pump Unit
1 HEV ECU
10A
HPCU
FUSE
H/LAMP HI
20A
Head Lamp Hi Relay
IGPM (Leak Current Autocut Device Fuse - INTERIOR LAMP/MEMORY 1/MEMORY 2/
4 B+
40A
MULTI MEDIA, Fuse -BRAKE SWITCH/SMART KEY/S/HEATER FRT/
BATTERY MANAGEMENT/DR LOCK)
2 EPB
30A
Electric Parking Brake Module
1 EPB
30A
Electric Parking Brake Module
3 IG3
10A
OBC Unit
HEATED
10A
A/C Control Module, Drover/Passenger Power Outside Mirror
MIRROR
7-78
Engine compartment main fuse panel (Plug-in hybrid) - PCB Block
Fuse Name
Fuse rating
Protected Component
2 HEV
10A
HPCU
ECU
1 POWER
20A
Front Power Outlet
OUTLET
FUEL PUMP
20A
Fuel Pump Relay
HORN
20A
Horn Relay, ICM Relay Box (Burglar Alarm Horn Relay)
WIPER
30A
Front Wiper (Low) Relay, Front Wiper (High) Relay
2 TCU
15A
Electric Water Pump
3 AHB
10A
Integrated Brake Actuation Unit
2 POWER
20A
Rear Power Outlet
OUTLET
B/UP LAMP
10A
Transaxle Range Switch, PCM, Audio, Electro Chromic Mirror, Back-Up Lamp LH/RH
1 SENSOR
15A
Oxygen Sensor (Up/Down)
E/R Junction Block (FTIV Relay, Cooling Fan Relay), Mass Air Flow Sensor, Oil Control Valve #1/#2,
2 SENSOR
10A
Purge Control Solenoid Valve, Fuel Pump Relay ELCM (Evaporative Leak Check Module),
Camshaft Position Sensor #1/#2
2 ECU
10A
PCM
7
1 TCU
10A
PCM
2 OPCU
10A
Electric Oil Pump Unit
BATTERY
15A
E/R Junction Block (Battery C/FAN Relay)
C/FAN
1 ECU
20A
PCM
IGN COIL
20A
Ignition Coil #1/#2/#3/#4
AMS
10A
Battery Sensor
7-79
Maintenance
LIGHT BULBS
Consult an authorized HYUNDAI
i Information
WARNING
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
After heavy driving, rain or washing,
headlamp and trunk lenses could
•
Prior to replacing a lamp,
light bulbs because other parts of the
vehicle must be removed before you
appear frosty. This condition is caused
depress the foot brake, move
by the temperature difference
the shift lever into P
(Park)
can get to the bulb. This is especially
true for removing the headlamp
between the lamp inside and the out-
apply the parking brake, place
side temperature. This is similar to the
the igntion switch to the
assembly to get to the bulb(s).
condensation on your windows inside
LOCK/OFF position, and take
Removing/installing the headlamp
your vehicle during the rain and does-
the key with you when leaving
assembly can result in damage to
n’t indicate a problem with your vehi-
the vehicle to avoid sudden
the vehicle.
cle. If the water leaks into the lamp
movement of the vehicle and
bulb circuitry, have your vehicle
to prevent possible electric
checked by an authorized HYUNDAI
shock.
dealer.
•
Be aware the bulbs may be hot
and may burn your fingers.
7-80
Headlamp, parking lamp,
• Always handle them carefully, and
turn signal lamp and side
avoid scratches and abrasions. If
marker light bulb replacement
the bulbs are lit, avoid contact with
liquids.
Type A - Halogen Headlamps
• Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
• A bulb should be operated only
when installed in a headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
OLMB073042L
and carefully dispose of it.
Headlamp (Halogen bulb)
WARNING
OLFH074018L
• Handle halogen bulbs with
(1) Headlamp (Low)
care. Halogen bulbs contain
pressurized gas that will pro-
(2) Headlamp (High)
duce flying pieces of glass
(3) Side marker lamp
7
that could cause injuries if
(4) Turn signal lamp
broken.
(5) LED Daytime running lamp(DRL)
• Wear eye protection when
/Parking lamp
changing a bulb. Allow the
bulb to cool down before han-
dling it.
7-81
Maintenance
8. Connect the headlamp bulb sock-
i
Information
et-connector.
The headlamp aiming should be
9. Install the headlamp bulb cover by
adjusted after an accident or after the
turning it clockwise.
headlamp assembly is reinstalled at an
authorized HYUNDAI dealer.
Low beam
High beam
OLFH074030L
1. Open the hood.
2. Disconnect the negative battery
cable.
3. Remove the headlamp bulb cover
by turning it counterclockwise.
4. Disconnect the headlamp bulb
socket-connector.
5. Unsnap the headlamp bulb retain-
ing wire by pressing the end and
pushing it upward.
6. Remove the bulb from the head-
lamp assembly.
7. Install a new headlamp bulb and
snap the headlamp bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7-82
5. Install a new bulb by inserting it
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly
and turn the socket clockwise.
Turn signal lamp
OLFH074030
OLF074084N
Turn signal lamp
Side marker lamp
1. Open the hood.
1. Open the hood.
2. Disconnect the negative battery
2. Disconnect the negative battery
cable.
cable.
3. Remove the socket from the
3. Remove the socket from the
assembly by turning the socket
assembly by turning the socket
counterclockwise until the tabs on
counterclockwise until the tabs on
the socket align with the slots on
the socket align with the slots on
7
the assembly.
the assembly.
4. Remove the bulb from the socket
4. Remove the bulb from the socket
by pressing it in and rotating it
by pulling out the bulb.
counterclockwise until the tabs on
5. Insert a new bulb.
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7-83
Maintenance
Daytime running lamp/
Type B - HID Headlamps
Headlamp (HID type)
Parking lamp (LED type)
Your vehicle is equipped with LED
WARNING
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
HID Headlamp low beam
does not operate, have the vehicle
Do not attempt to replace or
checked by an authorized HYUNDAI
inspect the low beam (XENON
dealer.
bulb) due to electric shock dan-
ger. If the low beam
(XENON
bulb) is not working, have your
vehicle checked by an author-
ized HYUNDAI Dealer.
OLFH074018L
(1) Headlamp (Low/High)
i
Information
(2) Side marker lamp
If your vehicle is equipped with High
(3) Turn signal lamp
Intensity Discharge (HID) headlamps,
(4) LED Daytime running lamp(DRL)
these headlamps contain mercury. So
/Parking lamp
if you need to have your vehicle dis-
posed, you should remove the HID
Headlamps before disposal. The
removed HID headlamps should be
recycled, re-used or disposed as haz-
ardous waste.
If the light bulb does not operate,
have the vehicle checked by an
authorized HYUNDAI dealer.
7-84
5. Install a new bulb by inserting it
i
Information
into the socket and rotating it until
HID lamps have superior perform-
it locks into place.
ance vs. halogen bulbs.
6. Install the socket in the assembly
HID lamps are estimated by the man-
by aligning the tabs on the socket
ufacturer to last twice as long or
with the slots in the assembly.
longer than halogen bulbs depending
7. Push the socket into the assembly
on their frequency of use. They will
and turn the socket clockwise.
probably require replacement at some
point in the life of the vehicle. Cycling
the headlamps on and off more than
Turn signal lamp
typical use will shorten HID lamps
OLFH074031
life. HID lamps do not fail in the same
Turn signal lamp
manner as halogen incandescent
lamps. If a headlamp goes out after a
1. Open the hood.
period of operation but will immedi-
2. Disconnect the negative battery
ately relight when the headlamp
cable.
switch is cycled it is likely the HID
3. Remove the socket from the
lamp needs to be replaced. HID light-
assembly by turning the socket
ing components are more complex
counterclockwise until the tabs on
than conventional halogen bulbs thus
the socket align with the slots on
7
have higher replacement cost.
the assembly.
4. Remove the bulb from the socket
NOTICE
by pressing it in and rotating it
counterclockwise until the tabs on
The headlamp aiming should be
the bulb align with the slots in the
adjusted after an accident or after
socket. Pull the bulb out of the
the headlamp assembly is rein-
socket.
stalled at an authorized HYUNDAI
dealer.
7-85
Maintenance
Daytime running lamp/
Side repeater lamp replace-
Parking lamp (LED type)
ment
Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, have the vehicle
checked by an authorized HYUNDAI
dealer.
OLF074084N
Side marker lamp
1. Open the hood.
OLF074053N
2. Disconnect the negative battery
If the LED lamp does not operate,
cable.
have the vehicle checked by an
3. Remove the socket from the
authorized HYUNDAI dealer.
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket
by pulling out the bulb.
5. Insert a new bulb.
7-86
Rear combination light bulb
replacement
Stop/Tail lamp
Type A
Turn Signal lamp
OLF074062
OLFH074026LE
Stop/Tail lamp and Turn signal lamp
3. Remove the socket from the
assembly by turning the socket
1. Open the trunk lid.
counterclockwise until the tabs on
OLFH074019
2. Remove the service cover by turn-
the socket align with the slots on
ing the lock counterclockwise and
(1) Stop/Tail lamp
the assembly.
then pulling it out.
4. Remove the bulb from the socket
(2) Turn signal lamp
by pressing it in and rotating it
(3) Tail lamp
counterclockwise until the tabs on
(4) Side marker lamp
7
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Install a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7-87
Maintenance
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Tail lamp
OLFH074064
OLFH074026L
Tail lamp
4. Remove the bulb by pulling it
straight out.
1. Open the trunk.
5. Install a new bulb by inserting it
2. Loosen the retaining screw of the
into the socket and rotating it until
trunk lid cover and then remove
it locks into place.
the cover.
6. Install the socket into the assem-
3. Disconnect the connector and
bly by aligning the tabs on the
then remove the screws by turning
socket with the slots in the assem-
the screws counterclockwise.
bly. Push the socket into the
assembly and turn the socket
clockwise.
7. Reinstall the trunk lid cover by
pushing in the screw.
7-88
Side marker lamp
Type B
Stop/Tail lamp
If the LED lamp does not operate,
If the LED lamp does not operate,
have the vehicle checked by an
have the vehicle checked by an
authorized HYUNDAI dealer.
authorized HYUNDAI dealer.
OLFH074023
(1) Stop/Tail lamp
(2) Turn signal lamp
(3) Side marker lamp
7
7-89