Fiat 500 (2023 year). Manual in english - page 2

 

  Index      Manuals     Fiat 500 (2023 year). Manual in english

 

Search            copyright infringement  

 

   

 

   

 

Content      ..      1      2      3      ..

 

 

 

Fiat 500 (2023 year). Manual in english - page 2

 

 

WINDOW WASHING
wiper is 10 seconds, independently
With the ring nut turned to the LO or HI
of the car speed. In position
, the
position, the smart washing function is
26) 27)
pause time between two strokes is set
not carried out.
The right stalk controls windscreen and
according to the car speed: when the
rear window wiper/washer operation.
speed increases, the time between two
WARNING If the stalk is activated for
strokes decreases. In position LO
WINDSCREEN WIPERS
less than half a second, only the screen
WITH AUTOMATIC
or HI, the windscreen wiper moves
washer jet is activated. Do not prolong
WIPING
continuously, i.e. without a pause
the activation of the "Smart Washing"
between two strokes.
8) 9)
function for more than 30 seconds.
When the car is stationary, if the
The ring (A) fig. 43 can be set to the
windscreen wiper is active in the HI
following positions:
MIST function
position, it automatically switches to
Windscreen wiper off
Move the stalk upwards (unstable
LO continuous slow flick operation.
Automatic wiping - slow flick
position) to activate the MIST
Continuous fast flick can be reactivated
function: operation is limited to the
Automatic wiping - fast flick
by moving the ring to a position other
time for which the stalk is held in this
(according to the car speed)
than HI and then back into HI, or by
position. When released, the stalk will
LO Constant slow flick
moving the car.
return to its default position and the
HI Constant fast flick
“Smart washing” function
windscreen wiper automatically stop.
Pull the stalk towards the steering
NOTE This function does not activate
wheel (unstable position) to operate the
the windscreen washer; windscreen
windscreen washer.
washer fluid will not therefore be
Keep the lever pulled to activate
sprayed onto the windscreen. To spray
both the windscreen washer jet
windscreen washer fluid onto the
and the windscreen wiper with a
windscreen, the washing function must
single movement; the latter turns on
be used.
automatically if you keep the lever
RAIN SENSOR
pulled for more than half a second. The
(where provided)
43
F0S1237
operation of the windscreen wiper
10) 11)
terminates three flicks after the stalk is
10)
This is located behind the interior
released; a final cleaning stroke several
With the ring nut (A) fig. 43
in position
seconds later completes the wiping
rear-view mirror fig. 44, in contact with
, the windscreen wiper is not
operation.
the windscreen and can measure the
activated. In position
, the pause time
amount of rain and, consequently,
between the strokes of the windscreen
manage the automatic wiping mode of
42
the windscreen in accordance with the
WARNING Keep the glass in the sensor
restored. The failure of the sensor is
amount of water on the screen.
area clean.
indicated by the symbol
lighting up
The rain sensor will be activated when
on the display.
the ignition device is ENGINE. If no rain
AUTOMATIC WIPING
If the rain sensor malfunctions, the
is detected, the wiper will not carry
wiper mode can be modified according
Automatic wiping can be selected
out any strokes. If it is raining, the
to the requirements. The malfunction
by selecting the rain sensor from the
windscreen wiper moves according to
display menu (see "Display screens"
signal remain active during the
the amount of rain measured by the
in the "Display" paragraph in the
operation time of the sensor or until the
sensor.
device is reset.
"Knowing the instrument panel"
section) or on the Uconnect™ system
When the car is stationary, if the
(see "Settings" in the "Vehicle mode"
windscreen wiper is moving at
paragraph in the "Multimedia" section)
maximum speed, it automatically
and turning the ring (A) fig. 43 in
moves to a reduced speed. HI mode
can be reactivated by moving the ring
position or
to a different position from and
These will be used to set the sensibility
then back or by moving the car.
level of the rain sensor: in position
,
the sensor has a lower sensitivity and
To deactivate automatic wiping, turn
the windscreens will activate when
the ring (B) to a position other than or
44
F0S1287
there is a significant amount of water
. This deactivation prevents unwanted
on the windscreen, while in position
,
activation of the wipers when the car is
The device is able to recognise,
the windscreen wipers will be activated
started (i.e. when the windscreen glass
and automatically adjust itself in the
by a minimum amount or measured
is being washed by hand or the wipers
presence of the following conditions:
rain.
are stuck to the screen by ice).
presence of dirt on the surface (e.g.
The activation of the automatic wiping
Inhibition
salt, dirt, etc.);
will be notified to the driver by a single
Moving the ignition device switch to
presence of streaks of water caused
stroke.
the STOP position, leaving the ring nut
by the worn windscreen wiper blades;
The same stroke will be visible every
difference between day and night.
(A) in position or
, when the car is
time the sensor sensitivity is increased,
next started (ignition device switch to
The rain sensor will be deactivated only
by rotating the ring nut from position
the ENGINE position), no wiping cycle
when the ignition device is turned to
to position
occurs for system protection reasons.
STOP.
The "Smart Washing" function activates
This temporary inhibition prevents
the normal washing cycle, after which
unwanted activation of the wipers
the automatic wiping function is
when the car is started (i.e. when the
43
windscreen glass is being washed by
stroke for each two strokes of the
IMPORTANT
hand or the wipers are stuck to the
windscreen wiper;
screen by ice).
With the ring in position
, the wiper
8) Never use the screen wiper to remove
It is possible to reactivate the automatic
active and reverse gear engaged, the
layers of snow or ice from the windscreen
wiping mode in three ways:
wiper is activated in synchronous
glass. In such conditions, the wiper
by turning the ring to the position
mode.
may be subjected to excessive stress
and then returning it to the or
With the ring in position
, the rear
and the motor cut-out switch, which
prevents operation for a few seconds, may
position;
window wiper is stopped.
intervene. If operation is not restored,
by moving the stalk upwards to the
NOTE If automatic wiping mode is
contact a Fiat Dealership.
MIST position;
active and the sensor does not detect
9) Do not operate the windscreen wiper
upon exceeding the 5 km/h speed
water, the rear window wiper will stays
with the blades lifted from the windscreen.
and the sensor detects rain.
still when the ring is turned to position
10) Do not activate the rain sensor when
washing the car in an automatic car wash.
REAR WINDOW WIPER /
11) Make sure the device is switched off if
WASHER
Push the stalk towards the dashboard
there is ice on the windscreen glass.
This operates only with the ignition
(rocking position) to activate the rear
window washer jet. Keep pushing
device at ENGINE.
the lever to automatically activate
PROGRAMMING THE
The ring (B) fig. 43 can be set to the
both the rear window washer jet and
CLIMATE CONTROL
following positions:
the rear window wiper with a single
SYSTEM
Wiper off
movement. Releasing the stalk will
Intermittent wiping
(where provided)
activate three strokes, as described for
Continuous wiping
The system provides two types
the windscreen wiper.
of remote climate control system
Rear Window Wiper
programming:
Turn the ring to (B) fig. 43 to operate
timely start of the climate control
the rear window wiper:
WARNING
system: this can be activated through
continuous: when the ring is in
the dedicated smartphone app (where
position
;
26) If the window needs to be cleaned,
provided). Refer to the "Connected
intermittent: when the ring is in
make sure the device is turned off or the
ignition device is in the STOP position.
Services - Uconnect Services" chapter
position and the windscreen wiper
27) Driving with worn windscreen/rear
in the "Multimedia" section.
wiper is stopped;
window wiper blades is a serious risk,
Programming the climate control
synchronous: when the ring is in
because visibility is reduced in bad
system with start time: This can be
position and the windscreen wiper is
weather.
activated either through the dedicated
moving or set to AUTO. In this mode,
smartphone app (where provided) or
the rear window wiper makes one
44
by programming a start time using the
heated windscreen where fitted) are
How to start climate control system
Uconnect™ system (see "ENGINE"
also activated.
programming
in the"Vehicle mode" paragraph of the
Select the programming function on
Programming the climate control
"Multimedia" section).
the dedicated app (where provided.
system with start time
Refer to the "Multimedia" section) to
Failed climate control
Select a time to start climate control
start the climate control system on-
system programming
system programming using the
demand or select an climate control
messages
Uconnect™ system or the dedicated
system programming start time on the
If the on-demand or programmed
app (refer to the "Multimedia" section);
Uconnect™ system or dedicated app
climate control system switch-on fails
the passenger compartment climate
(refer to the "Multimedia" section).
or ends early, dedicated messages will
control system will remain active unless
The doors of the car will lock, the
be displayed on the instrument panel
the ignition device is pressed;
climate control system programming
display.
The on-demand starting and
will start and the car will go into
programming of the climate control
How to use the
ENGINE mode. If the climate control
system can be successful in the
climate control system
system is started on-demand, the car
following conditions:
programming functions
will remain in ENGINE mode for 15
Doors closed
Starting the climate control system
minutes; if the climate control system is
Bonnet closed
Select the programming function on
programmed to start at a certain time,
Boot closed
the dedicated app (where provided.
the car will remain in ENGINE mode.
Hazard lights not active
Refer to the "Multimedia" section).
NOTES
Alarm not active
The passenger compartment climate
In case of motor malfunction/fault,
Adequate 12V battery state of
control system will remain active for 15
the climate control system
charge
minutes unless the ignition device is
programming will be disabled.
Ignition device in the STOP position
pressed.
For safety reasons, both when the
Transmission in P position
This function can be activated twice
climate control system is started on-
If the start on-demand function has
after which it is necessary to turn the
demand or programmed with start
not been activated twice
ignition device to ENGINE to allow
time, the wipers are disabled when the
If the key is not inside the car
turning on the climate control system
function is active. For safety reasons,
(necessary condition for programming
app (where provided) on-demand
the windows are disabled when the
the climate control system with start
again.
climate control system is started on-
time)
If the ambient temperature is lower
demand.
than 4.5 °C when the function is
In case of activation of the climate
started, the electric defrosters (heated
control system on-demand, the sunroof
rear window, heated mirrors and
and soft top are also disabled.
45
Two 15-minute cycles of climate
CLIMATE CONTROL
use device (C) to adjust the diffuser
control system operation are possible
to the desired position (up / down / left
SYSTEM
after which the ignition device must
/ right);
be turned to the ENGINE position to
PASSENGER
Central air vents
perform new start cycles.
COMPARTMENT AIR
(A) fig. 47 - Adjustable and directable
DIFFUSERS
How to finish programming the
central vents:
Side air diffusers
climate control system without
use device (B) to adjust the diffuser
(A) fig. 45 - Fixed side air diffuser (driver
driving the car
to the desired position (up / down / left
and passenger side).
If the climate control system starts
/ right);
up on time, select the end of charging
function on the dedicated app (where
provided. Refer to the "Multimedia"
section) or wait for the end of the start
cycle (about 15 minutes).
In case of programming the climate
control system with start time, finish
charging through the programming
function on the dedicated app (where
provided. Refer to the "Multimedia"
45
F0S1123
47
F0S1125
section).
How to stop climate control system
programming and drive the car
Programming can be interrupted
with time or start the climate control
system on time by moving the ignition
device to the START position. A
dedicated message will appears on the
instrument panel.
46
F0S1124
(B) - Adjustable side vents:
46
MANUAL CLIMATE CONTROL SYSTEM
(where provided)
CONTROLS ON THE CLIMATE CONTROL FRONT PANEL
A
B C D E F G H
I
48
F0S1218
A. introduced air temperature up/down button B. climate control compressor on/off button C. air to feet button D. air to body
button E. window demisting/defrosting button F. rapid window defrosting/demisting on/off button G. heated rear window on/off
button H. internal air recirculation on/off button I. fan speed adjusting button
47
CONTROLS ON Uconnect™ 10.25" SYSTEM DISPLAY
(where provided)
49
F0S1219
There are graphic buttons on the Uconnect™ system that let you turn on the functions described in this paragraph.
48
CONTROLS ON Uconnect™ 7" SYSTEM DISPLAY
(where provided)
Off
50
F0S2069
There are graphic buttons on the Uconnect™ system that let you turn on the functions described in this paragraph.
49
Description of the
You can select the combination of
When the outside temperature is low,
controls
several modes by pressing the buttons
recirculation could be switched off (air
Air temperature
in sequence.
drawn from the outside) to prevent the
adjustment
windows misting up.
Fan speed adjustment
Press the (A) fig. 48button:
To guarantee good air quality inside
Press button (I) to increase/decrease
press downwards: decrease
the passenger compartment, every 15
the fan speed:
temperature;
minutes of recirculation, the system
press downwards: decrease speed;
press upwards: temperature rise.
takes in air from outside for 1 minute
press upwards: increase speed.
By repeatedly pressing the (A) button
and then returns to recirculation.
The speed is displayed on the A/C
upwards or downwards the HI
Climate control
screen of the Uconnect™ system. A
(maximum air temperature) and LO
specific fan level can be selected by
compressor
(minimum air temperature) functions are
pressing the button
:
Press button (B) fig. 48 to
switched on respectively. To turn these
activate/deactivate the compressor.
maximum fan speed: all bars are lit
functions off, ask for a numerical air
Switching off the compressor remains
up;
temperature.
stored even after the ignition device has
minimum fan speed: one bar is lit
Air distribution selection
been turned to the STOP position.
up.
You can manually set one of the
Air recirculation
following air distributions by pressing
WARNING With the compressor off, air
The air recirculation can be switched
the (C), (D), (E), (F) fig. 48 buttons on
cannot be introduced to the passenger
on/off by pressing the button (H)
the dashboard or the graphic buttons
compartment with a temperature
fig. 48.
located on the Uconnect™ system
lower than the external temperature.
display:
Moreover, under certain environmental
Airflow at central and side
WARNING The engagement of the
conditions, windows could mist up
dashboard vents to ventilate the chest
recirculation system makes it possible
rapidly since the air is not dehumidified.
to reach the required heating/cooling
during the hot season.
conditions faster. It is, however,
Airflow to the front and rear footwell
Heated rear window
inadvisable to use it on rainy/cold days,
vents. This air distribution setting heats
demisting/defrosting
or with low external temperatures, as
the passenger compartment most
Press button (G) fig. 48 to
it would considerably increase the
quickly, giving a prompt sensation of
activate heated rear window
possibility of the windows misting up
warmth.
demisting/defrosting.
inside rapidly (especially if the climate
Air flow towards windscreen.
Whenever the ignition device switches
control system is off).
Maximum windscreen defrosting.
to the START position, the function
switches off automatically after approx.
50
10 minutes the first time it is activated.
HEATER
automatically (but can be reactivated
The following activations have a
The heater activates automatically
manually, if necessary).
duration of 5 minutes.
depending on the environmental
NOTE Some climate control system
If this function is provided, pressing
conditions and with ignition device in
functions may be unavailable in “Turtle”
the button
also activates
the START position.
mode, in which case the LEDs on the
demisting/defrosting of door mirrors
buttons of the climate control system
System maintenance
and heated vents (where provided).
controls will flash.
4)
In winter, the climate control system
WARNING Do not apply stickers to the
must be turned on at least once a
inside of the heated rear window over
IMPORTANT
month for about 10 minutes.
the heating filaments, to avoid damage
Before summer, have the system
that might cause them to stop working
4) The system uses R1234yf coolant,
checked at a Fiat Dealership.
which does not pollute the environment
properly.
in the event of accidental leakage. Under
OPERATING
no circumstances use R134a and R12
LIMITATIONS
SWITCHING THE
fluids, which are incompatible with the
With the car in "SHERPA" or "TURTLE"
components of the system.
CLIMATE CONTROL
mode, climate control limitations are
SYSTEM OFF/BACK ON
automatically introduced to preserve
Switching off the climate control
the range.
system
In "SHERPA" mode, the climate control
Press the A/C button (B) fig. 48.
system and the mirror and seat heater
With climate control system off:
are deactivated (but can be manually
air recirculation is on, thus isolating
reactivated, if necessary).
the passenger compartment from the
The "TURTLE" mode:
outside;
Range from 8 to 24 km: The heated
the compressor is off;
rear window, mirrors, windscreen and
the fan is off;
seats are deactivated automatically
the heated rear window can be
(but can be reactivated manually, if
activated/deactivated.
necessary).
Switching on the climate control
Range lower than 8 km: The climate
system
control system is deactivated, the fan
To turn the climate control system back
and quick defrosting may be activated.
on press the A/C button (B) fig. 48.
The heated rear window, mirrors,
windscreen and seats are deactivated
51
AUTOMATIC CLIMATE CONTROL SYSTEM
CONTROLS ON THE CLIMATE CONTROL FRONT PANEL
51
F0S1126
A. temperature up/down button B. AUTO function activation button (automatic operation) C. climate control compressor on/off
button D. air to feet button E. air to body button F. window demisting/defrosting button G. rapid window defrosting/demisting
on/off button H. heated rear window on/off button I. internal air recirculation on/off button L. climate control system on/off
button M. fan speed adjusting button
52
CONTROLS ON Uconnect™ 10.25" SYSTEM DISPLAY
(where provided)
N
Comfort
52
F0S1127
There are graphic buttons on the Uconnect™ system that let you turn on the functions described in this paragraph.
53
CONTROLS ON Uconnect™ 7" SYSTEM DISPLAY
(where provided)
Off
53
F0S2070
There are graphic buttons on the Uconnect™ system that let you turn on the functions described in this paragraph.
54
Description of the
compressor on/off, compatibly with
In this way the system operates
controls
environmental conditions;
completely automatically to adjust the
Description
variation of set temperature;
temperature, quantity and distribution
The automatic climate control system
heated rear window
of the air introduced into the passenger
maintains comfort inside the passenger
activation/deactivation.
compartment. It also manages the air
compartment and compensates for
The amount of air introduced into the
recirculation system and the enabling
possible variations in outside weather
passenger compartment is not affected
the air conditioning compressor.
conditions.
by car speed; it is electronically
During automatic operation, you
The reference temperature is 22°C for
controlled by a fan.
can change the set temperatures,
optimal comfort management.
The temperature of the air sent is
activate/deactivate the rear window,
The automatically controlled
always automatically controlled
activate/deactivate the compressor and
parameters and functions are:
according to the temperature set on
the recirculation at any time by using
the display (except for when the system
the relevant buttons; the system will
air temperature at the driver/front
is off or in certain conditions when the
automatically change the settings to
passenger side vents;
compressor is not running).
adjust to the new requirements.
air distribution at the driver/front
passenger side vents;
The system allows the following to be
In this way the climate control system
fan speed (continuous variation of the
set or adjusted manually:
will continue to automatically manage
air flow);
air temperature;
all functions except for those that have
compressor engagement (for
fan speed has 7 positions;
been manually adjusted. The fan speed
cooling/dehumidifying the air);
air distribution;
is the same in all the zones of the
air recirculation.
compressor enabling;
passenger compartment.
All these functions can be adjusted
rapid defrosting/ demisting function;
Air temperature
manually by operating the system and
air recirculation;
adjustment
selecting one or more functions and
heated rear window;
Press the (A) fig. 51button:
modifying their parameters.
system deactivation.
press downwards: decrease
Manual selections always have higher
Operating mode
temperature;
priority than automatic settings and
The climate control system can
press upwards: temperature rise.
are stored until the AUTO button is
be activated in different ways: it is
By repeatedly pressing the (A) button
pressed, except for cases in which the
advisable to press the AUTO button
upwards or downwards the HI
system intervenes for safety reasons.
and press the button (A) fig. 51 to set
(maximum air temperature) and LO
The following operations do not
the desired temperatures.
(minimum air temperature) functions are
deactivate the AUTO function:
switched on respectively. To turn these
recirculation on/off;
55
functions off, ask for a numerical air
Fan speed adjustment
To restore automatic system control
temperature.
Press button (M) to increase/decrease
after one or more manual adjustments,
the fan speed:
press the AUTO button.
Air distribution selection
press downwards: decrease speed;
You can manually set one of the
Air recirculation
press upwards: increase speed.
following air distributions by pressing
The air recirculation can be switched
The speed is displayed on the A/C
the (D), (E), (F), (G) fig. 51 buttons on
on/off by pressing the button (I) fig. 51.
the dashboard or the graphic buttons
screen of the Uconnect™ system. A
specific fan level can be selected by
located on the Uconnect™ system
WARNING The engagement of the
display:
pressing the button
:
recirculation system makes it possible
Airflow at central and side
maximum fan speed: all bars are lit
to reach the required heating/cooling
dashboard vents to ventilate the chest
up;
conditions faster. It is, however,
during the hot season.
minimum fan speed: one bar is lit
inadvisable to use it on rainy/cold days,
Airflow to the front and rear footwell
up.
or with low external temperatures, as
vents. This air distribution setting heats
it would considerably increase the
the passenger compartment most
WARNING To restore automatic
possibility of the windows misting up
quickly, giving a prompt sensation of
control of the fan speed after a manual
inside rapidly (especially if the climate
warmth.
adjustment, press the AUTO button.
control system is off).
Air flow towards windscreen.
Maximum windscreen defrosting.
AUTO button
When the outside temperature is low,
When the AUTO button is pressed the
recirculation could be switched off (air
You can select the combination of
climate control system is automatically
drawn from the outside) to prevent the
several modes by pressing the buttons
adjusted in the corresponding zones:
windows misting up.
in sequence.
quantity and distribution of the
In automatic operation inside air
In AUTO mode, the climate control
air introduced into the passenger
recirculation will be controlled
system automatically manages the
compartment;
automatically by the system according
air distribution. The air distribution,
climate control compressor;
to outside environmental conditions.
when manually set, is displayed on the
air recirculation;
Uconnect™ system A/C screen.
Climate control
cancelling any previous manual
compressor
settings.
Press button (C) fig. 51 to
If a manual intervention is made on
activate/deactivate the compressor.
the air distribution or on the fan speed
Switching off the compressor remains
the climate control system is no longer
stored even after the ignition device has
controlling all functions automatically.
been turned to the STOP position.
56
To restore automatic control of
that might cause them to stop working
HEATER
compressor engagement, press again
properly.
The heater activates automatically
button (C) or the AUTO button (B)
depending on the environmental
fig. 51.
SWITCHING THE
conditions and with ignition device in
CLIMATE CONTROL
the START position.
WARNING With the compressor off, air
SYSTEM OFF/BACK ON
System maintenance
cannot be introduced to the passenger
Switching off the climate control
5)
compartment with a temperature
system
In winter, the climate control system
lower than the external temperature.
Press the OFF button (L) fig. 51.
must be turned on at least once a
Moreover, under certain environmental
With climate control system off:
month for about 10 minutes.
conditions, windows could mist up
air recirculation is on, thus isolating
Before summer, have the system
rapidly since the air is not dehumidified.
the passenger compartment from the
checked at a Fiat Dealership.
outside;
Heated rear window
the compressor is off;
OPERATING
LIMITATIONS
demisting/defrosting
the fan is off;
Press button (H) fig. 51 to
the heated rear window can be
With the car in "SHERPA" or "TURTLE"
activate heated rear window
activated/deactivated.
mode, climate control limitations are
automatically introduced to preserve
demisting/defrosting.
The climate control system control unit
the range.
Whenever the ignition device switches
stores the temperatures set before the
to the START position, the function
system was switched off and restores
In "SHERPA" mode, the climate control
switches off automatically after approx.
them when any button of the system is
system and the mirror and seat heater
10 minutes the first time it is activated.
pressed.
are deactivated (but can be manually
reactivated, if necessary).
The following activations have a
Switching on the climate control
duration of 5 minutes.
The "TURTLE" mode:
system
If this function is provided, pressing
Range from 24 to 8 km: The heated
To switch on the climate control
the button
also activates
rear window, mirrors, windscreen and
system in fully automatic mode press
seats are deactivated automatically
demisting/defrosting of door mirrors
the AUTO button (B) fig. 51.
and heated vents (where provided).
(but can be reactivated manually, if
necessary).
Range lower than 8 km: The climate
WARNING Do not apply stickers to the
control system is deactivated, the fan
inside of the heated rear window over
and quick defrosting may be activated.
the heating filaments, to avoid damage
The mirror, windscreen and seat heater
57
are deactivated (but can be manually
reactivated, if necessary).
NOTE Some climate control system
functions may be unavailable in “Turtle”
mode, in which case the LEDs on the
buttons of the climate control system
controls will flash.
IMPORTANT
54
F0S1095
55
F0S1177
5) The system uses R1234yf coolant,
Press and hold the button for a few
WINDOW
which does not pollute the environment
seconds and the window winds down
OPENING/CLOSING BY
in the event of accidental leakage. Under
automatically. Where provided, keeping
MEANS OF A KEY WITH
no circumstances use R134a and R12
the button raised for a few seconds,
REMOTE CONTROL
fluids, which are incompatible with the
will automatically wind the window up.
(where provided)
components of the system.
On some versions, the windows can be
CLOSING WITH PASSIVE
opened/closed by holding the unlock
ENTRY
ELECTRIC WINDOWS
(where provided)
(
) / lock (
) buttons pressed,
28) 29)
respectively.
On some versions equipped with
They work with the ignition device in
Passive Entry, pressing the door lock
ANTI-PINCH DEVICE
the ENGINE position and for about
button (C) fig. 55 the windows close
(where provided)
three minutes after the ignition device
automatically as long as the lock button
According to the versions, the car is
has been turned to the STOP position.
is pressed by the user.
equipped with an anti-pinch safety
When one of the front doors is opened
function for the raising of the front
this operation is disabled.
windows.
The electric window control buttons
This safety system can recognise the
are located on the armrest of the door
presence of any obstacle during the
panel and activate fig. 54:
window closing movement. If this
(A) Opening/closing of the left window.
occurs, the system stops the window's
(B) Opening/closing of the right
movement and reverts it, depending on
window.
its position.
58
This device is also useful if the windows
by personal objects getting caught in the
are activated accidentally by children
mechanism or by being hit by it directly.
on board the car.
29) When leaving the car, always set the
ignition device in the STOP position and
The anti-pinch safety function is
take the electronic key with you to avoid
activated both during the manual and
A
the risk of injury of people still on board
the automatic operation of the window.
due to accidental operation of the power
When the anti-pinch system is
windows.
30) If the anti-pinch protection intervenes
activated the window travel is
three consecutive times in one minute or
immediately interrupted. Then the
is faulty, the automatic closing operation
window stroke is automatically
of the window is inhibited, only allowing it
56
F0S1269
inverted.
in "steps"; the button is released for the
subsequent manoeuvre. In order to restore
SUNROOF
30)
the correct operation of the system, the
(where provided)
ELECTRIC WINDOWS
respective window must be wound down.
31)
SYSTEM INITIALISATION
12) 13) 14)
If power supply is interrupted when
ROOF
the window is moving, the electric
To move the sunshade, follow the
window automatic operation must be
FIXED GLASS SUNROOF
instructions in “fixed glass roof”.
reinitialised. The initialisation procedure
(where provided)
Opening
described below must be carried out
The roof comprises a wide fixed
Press button (A) located near the front
with the doors closed and for each
glass panel and a manually-operated
ceiling light pressed fig. 57, to move
door:
sunshade. The blind can be used in the
the roof to “vent” position. With the roof
fully close the window to be
"all closed" or "all open" positions.
open in “vent” position, hold button (A)
initialised, with manual operation;
To open the blind, grab the handle,
pressed again to move the roof to all
after the window has reached the
press the tooth (A) fig. 56 and move it
open position.
upper end of travel, hold the up button
to the completely open position.
down for at least 3 seconds.
To close it, grab the grip and move the
blind to the closed position until catch
(A) is attached.
WARNING
28) Improper use of the electric windows
can be dangerous. Before and during their
operation, ensure that any passengers are
not at risk from the moving glass either
59
after full closing, wait for the sunroof
WARNING
motor to stop.
EMERGENCY OPERATION
A
B
31) When leaving the car, make sure
If the electrical device for moving the
to take the key with you to avoid the
roof fails, the sunroof can be moved
risk of injury to those still inside the
car due to accidental operation of the
manually proceeding as described
sunroof. Improper use of the roof can be
below:
dangerous. Before and during operation,
always check that no-one is exposed to
the risk of being injured by the moving
57
F0S1330
sunroof or by objects getting caught or hit
by it.
Closing
Press button (B) fig. 57 from the all
IMPORTANT
open position: the front glass panel will
move into the “vent” position. Press
12) You are advised to use the sunroof
button (B) again to reach the all closed
only at "vent" position if a transverse roof
position of the roof.
rack is fitted.
58
F0S1331
13) Do not open the sunroof if there is
ANTI-PINCH DEVICE
snow or ice on it: you may damage it.
The sunroof has an anti-pinch safety
for manual activation remove the
14) Be careful not to hit objects on the roof
system capable of detecting the
protective cap (A) fig. 58 from its
rack when you open the tailgate.
presence of an obstacle whilst the roof
housing which is located on the internal
is closing. When this happens, the
covering behind the sunshade
system stops and the movement of the
take the hex wrench provided from
roof is immediately reversed.
the tool bag in the boot
insert the key provided into housing
INITIALISATION
(B) fig. 58and turn it clockwise to open
PROCEDURE
the roof or anticlockwise to close the
The sunroof must be reinitialised after
roof.
disconnecting the 12V battery or if the
corresponding protective fuse is blown.
Proceed as follows:
keep the button (B) fig. 57 pressed
so that the roof closes completely in
stages
60
SOFT TOP
SOFT TOP MOVEMENT
32) 33) 34)
(where provided)
15) 16) 17)
The cabrio versions are provided with
A
B
an automatically actuated electric soft
top.
WARNING The motor may overheat
The soft top can be opened and closed
if the soft top is repeatedly operated
using the controls inside the car
within a short space of time, thus
located near the ceiling light or the
causing the overheating protection to
remote control buttons. The soft top
inhibit system operation. Wait for a
60
F0S1317
can also be closed using the "Passive
minute and repeat.
Entry" system.
Closing
The soft top can be automatically
Opening
Press button (B) fig. 60 from the all
opened from the closed position to the
By pressing the button (A) located
open position, the soft top will move
spoiler position, and from this position
near the front fig. 60 ceiling light for
into the “spoiler” position. By pressing
to the all open position fig. 59.
more than half a second, the soft
the button again (B) the soft top can be
top will automatically move to the
all closed for more than half a second
"spoiler" position (automatic opening).
(automatic closing). From the "spoiler"
By pressing the button for a shorter
position, by pressing the button for
time, the soft top will move "jerky" to
a shorter time, the soft top will move
the "spoiler" position (manual opening).
"jerky" to the all closed position (manual
With the soft top automatically open
closing). From the all open position to
in “spoiler” position, hold button (A)
the "spoiler" position, only automatic
pressed again to move the soft top to
movement is allowed.
all open position. From the "spoiler"
59
F0S1268
Opening the tailgate with top all
position until all open, only automatic
open
Suggestions
movement is allowed.
Press the tailgate opening button (F)
it is advisable to close the soft top
fig. 61 once to automatically close the
when the car is parked. The closed soft
roof to spoiler position. The tailgate can
top effectively protects the car from
be opened in spoiler position.
bad weather and from theft;
it is advisable to put valuables in the
boot and lock the lid even when the
soft top is closed.
61
The soft top can be operated at any
Do not keep the soft top folded for
temperature in the range from -18 to
a long time: this could cause folds and
+80 °C.
creases in the fabric.
If required, remove the 12V battery
Before moving the soft top, check
with the soft top either open or closed,
that there is enough room to carry out
but NOT while it is moving.
the operation and that there are no
Do not fix roof racks to the soft top
obstacles or people close to its moving
and do not travel with objects resting
parts.
on the open top.
The cooled air flow into the
The activation of the heated rear
passenger compartment may decrease
61
F0S1102
windscreen, upon request by the
if the automatic climate control system
OPERATION BY MEANS OF
user, is carried out only if the soft
is on and the soft top is not completely
REMOTE CONTROL
top is completely closed. If the soft
closed.
top is closed incorrectly, the heated
With the soft top open and the car
The remote control can only be used
rear window will not function and the
travelling, the voice recognition system
with the ignition device in the STOP
position and the doors closed.
corresponding warning light will not
may not recognise voice commands
turn on.
because of the background noise:
The soft top can only be moved using
When the soft top is opened using
with the soft top closed and at a high
the remote control when it is between
the relevant control, if the heated rear
speed, the voice function for number
the all closed position and the spoiler
windscreen had been engaged it is
dialling may not be recognised.
position. It is not possible to move
automatically deactivated and the
ANTI-PINCH DEVICE
the soft top if it is between the spoiler
warning light switches off
The soft top has an anti-pinch safety
position and the all open position.
Do not remove ice from the soft top
system capable of detecting the
Continuously pressing the button
with a sharp item.
presence of an obstacle during the
on the key, the roof opens and stops
To prevent damage, do not use
closing movement: if this happens, the
in any position when the button is
scrapers or sprays to remove ice from
system intervenes and the movement
released.
the heated rear window.
of the soft top is immediately reversed
WARNINGS
Do not put objects on the soft top:
into opening.
The horizontal and vertical parts of
they could fall if the it is operated,
After five consecutive activations of the
the soft top can be operated at any
causing damage and injury.
anti-pinching function in one minute,
speed lower than 100 and 80 km/h
It is advisable to cover the soft top
the soft top must be recalibrated. For
respectively.
with a protective sheet if the car is left
recalibration, see the "Initialisation
parked in the open for a long time.
procedure" paragraph.
62
CLOSING WITH PASSIVE ENTRY
take the key (A) fig. 63 provided and
as described in the “Boot” chapter
(where provided)
located in the boot in combination with
of the “Knowing your car” section,
If the car is equipped with Passive
the tool bag or the Fix&Go kit;
then manually move the soft top as
Entry function, by pressing the door
described above.
lock button (C) fig. 62 the soft top will
To restore the automatic movement
close as long as the user holds down
conditions, apply to Fiat Dealership.
the lock button.
INITIALISATION
PROCEDURE
WARNING The soft top can only be
A
The soft top must be reinitialised after
moved from "Passive Entry" when
disconnecting the 12V battery or if the
the soft top is between the all closed
corresponding protective fuse is blown.
position and the spoiler position. It is
Proceed as follows:
not possible to move the soft top if it is
63
F0S1311
with the ignition device in the
between the spoiler position and the all
ENGINE position, keep the opening
open position.
fit the key in position, visible from
button pressed until the soft top is
inside the boot beneath the parcel shelf
completely open;
in the point shown in fig. 64;
when the soft top is completely
turn: clockwise to open the soft top;
open, keep the button pressed for at
anticlockwise to close it.
least 2 seconds;
keep the closing button pressed until
the soft top is completely closed;
once the all closed position has been
reached, continue to press the button
until the soft top makes a full opening
and closing run.
62
F0S1177
If the soft top is already initialized, the
A
user can perform a new initialisation by
EMERGENCY OPERATION
the following steps:
64
F0S1344
If the buttons fail, the soft top can
keep the opening button pressed
be moved manually proceeding as
until the soft top is completely open;
If the tailgate fails to open because the
described below:
when the soft top is completely
12V battery is flat, or following a fault
open, keep the button pressed for at
in the tailgate electric lock, perform the
emergency tailgate opening procedure
63
least 30 seconds (to force the loss of
re-position the backrest correctly; the
initialisation);
Wind Stop is locked between the seat
keep the closing button pressed until
and parcel shelf.
the soft top is completely closed;
FRONT SPOILER
once the all closed position has been
The car is provided with a front spoiler
reached, continue to press the button
which can be raised to improve
until the soft top makes a full opening
aerodynamic comfort inside the
and closing run.
passenger compartment.
WIND STOP
To lift the spoiler, release the catch
67
F0S1320
The Wind Stop fig. 65 is designed to
by means of the slider (A) moving it to
improve driving comfort, by reducing
position (2) as shown in fig. 66
It is advisable to raise the spoiler when
air turbulence in the passenger
With the spoiler raised, take care not to
the horizontal segment of the top
compartment when travelling with the
move the slider (A) from position (1) to
is open and at speeds faster than
soft top down.
position (2).
50 km/h.
To use the Wind Stop fig. 65:
With the top completely open, it is
advisable to keep the spoiler lowered
to limit wind noise inside the passenger
1
compartment.
Raising the spoiler will reduce the flow
of air to the rear seats.
2
A
WASHING/CLEANING
THE SOFT TOP
66
F0S1319
18) 19) 20) 21) 22) 23) 24) 25)
65
F0S1318
Use of specific products is
To lower the spoiler, press and move
recommended for washing the soft top
Release the backrest of the rear seat
the slider to position fig. 67 to lock it
cloth.
(single or split).
once the slider’s catch is positioned
The soft top fabric is treated with a
Attach the Wind Stop by inserting
inside its housing (1) fig. 66.
special water-repellent, waterproof
the central part inside the rear screen
product. The water-repellent properties
guard, with the concave part in the
will degrade in time with exposure to
direction of the passenger, as shown in
the weather elements. Observe the
fig. 65;
following instructions.
64
Remove as much dirt from the surface
Use common, care mild stain removers
18) Bird droppings and plant resins must
of the soft top with a soft brush or
that can be purchased from car
be washed off immediately and thoroughly
vacuum cleaning before washing
cleaning product ranges to remove
from the soft top as the acid they contain
is particularly aggressive.
it. This operation will considerably
more stubborn stains. Apply by blotting
19) Never use high-pressure washing
improve the final result.
(never rubbing) directly on the area of
systems.
In lack of specific products, use water
the stain.
20) When using steam washers or
and neutral soap applied with a sponge
high-pressure water washers, maintain
(preferably in the shade) for washing.
a suitable distance and do not exceed a
maximum temperature of 60°C. Damage,
Rinse the soft top with clean water after
WARNING
alterations and water infiltration may
having eliminated all the stains.
occur if the distance is too small and the
Hand washing is recommended;
32) Keep hands away from the top
pressure is too high.
modern automatic washing systems
mechanism while opening and closing the
21) If a water jet is used, direct away
top or if the top stops in a position before
from the edges of the fabric and the rear
equipped with soft brushes which
completing the cycle to prevent damage
window frame to prevent water infiltration.
do not apply excessive pressure and
and injury.
22) Never use alcohol, petrol, chemical
employ specific soft top products may
33) Keep children away from the area in
products, detergents, stain removers, wax,
be used.
which the top is folding during opening or
solvents and "wash and polish" products.
closing operations.
Leave the car in the shade after
23) Rinse immediately to remove soap
34) When leaving the car, turn the ignition
to prevent stains. Repeat the operation if
washing avoiding direct sunlight.
device to STOP and always take the
needed.
Waterproofing the soft top
electronic key with you to avoid the risk of
24) Follow the instructions on the
injury due to accidental operation of the
Use specific waterproofing products for
waterproofing product container for
soft top. Improper use may be dangerous.
fabric soft tops.
perfect results.
Before and during operation, always check
25) The rubber seals on the soft top
that no-one is at risk of being injured by
Interior soft top fabric
must be cleaned exclusively with water.
the moving soft top or by objects getting
Remove dust with a soft brush. Avoid
If you notice that this trim is dry or is
caught and dragged by it.
sticking, apply talcum powder or products
using hard brushes made of synthetic
specifically for rubber trim (silicone spray).
material to prevent damaging the fabric
IMPORTANT
beyond repair.
Clean the surface with a microfibre
15) Never open the top in presence of
cloth or soft sponge dipped in a
snow or ice to prevent damage.
solution of water and neutral soap.
16) Do not place objects on the rear
Clean the entire surface, including the
window shelf to prevent damage while the
zones where cleaning is not needed, to
top is closing.
prevent staining.
17) Loads may not be secured on the roof.
65
BOOT
fig. 68 if a valid key is detected near the
rear of the car.
35) 36)
A handle (B) fig. 69 is provided inside
ELECTRIC HANDLE
the tailgate to make it easier to close.
(SOFT TOUCH)
The tailgate can be opened at any time
if the doors are unlocked.
To open it, enable the handle, opening
one of the front doors or unlocking the
doors with the remote control.
68
F0S1102
Operate the electric handle (F) fig. 68
to open the tailgate.
Opening the tailgate with soft top
all open
To release the lock with the remote
control, press button
Pressing the tailgate opening one-
69
F0S1332
For cars with the Passive Entry
touch button (F) fig. 68 to automatically
system, even if the doors are locked,
close the soft top to spoiler position.
EMERGENCY TAILGATE
The tailgate can be opened in spoiler
the boot can be opened using the
OPENING
position.
electric handle (F) with a valid key
To open the tailgate from the inside if
detected near the rear of the car.
the 12V battery in the car is flat or the
To close, use the handle located
WARNING It is not possible to open
electric lock on the tailgate is faulty,
inside the tailgate.
the boot if the soft top has not been
proceed as follows:
If the tailgate is not shut properly the
initialised. Carry out the soft top
take out the rear head restraints;
dedicated instrument panel or colour
initialisation procedure as described in
tilt the backrests;
display warning light (where provided)
the section "Initialisation procedure" in
to unlock the tailgate mechanically,
will switch on.
the chapter "Soft top" in this section.
working from the inside of the boot,
remove the protective yellow cap and
CLOSING
then use lever (A) fig. 70.
To close, lower the tailgate by pressing
near the lock until you hear it click.
For cars equipped with the Passive
Entry system, the boot and all doors
can be locked with the button (G)
66
The car may be equipped with an
move the lever (B) fig. 73 leftwards as
optional charging cable, located inside
shown in the figure;
a special bag, placed in the boot.
WARNING
35) Never exceed the maximum permitted
load in the boot; see the “Technical
specifications” section. Also make sure
70
F0S1312
that the objects you place in the boot have
been properly secured, to avoid them from
CARGO BOX (standard
being thrown forward consequent to sharp
73
F0S1146
charging cable)
braking and injuring your passengers.
(for versions/markets where provided)
36) Be careful not to hit objects on the roof
raise the bonnet completely: the
rack when you open the tailgate.
The car is equipped with a "Mode 3” or
operation is facilitated by the presence
"Mode 2" charging cable depending on
of two gas springs which hold it the all
the versions/markets (A) fig. 71 located
BONNET
open position.
inside a special box placed in the boot.
Do not tamper with the gas shock
37) 38) 39)
absorber and accompany the bonnet
OPENING
while lifting it.
Proceed as follows:
CLOSING
pull the lever (A) fig. 72 in the
To close, lower the bonnet to
direction indicated by the arrow;
approximately 20 centimetres from
the motor compartment then let it
drop. Make sure that the bonnet
is completely closed and not only
fastened by the locking device by trying
71
F0S0845
to open it. If it is not perfectly closed,
do not try to press the bonnet down
Optional cable bag
but open it and repeat the procedure.
(for versions/markets where provided)
IMPORTANT Always check that the
bonnet is closed correctly to prevent
72
F0S1129
67
it from opening while the vehicle is
INTERIOR FITTINGS
travelling.
STORAGE
COMPARTMENTS
40)
WARNING
Lower compartment
37) Be very careful not to allow scarves,
To open the bottom drawer, pull the
neck ties and other loose articles of
lever (A) fig. 74. The flap opens down
clothing from touching, even accidentally,
automatically.
any moving parts. This may cause the
clothing to be pulled into the part, resulting
75
F0S1131
in serious risk to the wearer.
38) For safety reasons, the bonnet must
WARNING On both sides of the
always be properly closed while driving.
passenger side sun visor there is a
Therefore, make sure that the bonnet
is properly closed and that the lock is
label advising that it is compulsory to
engaged. If you discover that the bonnet
deactivate the airbag if a rear facing
is not perfectly closed while driving, stop
child restraint system is fitted. Always
immediately and close the bonnet in the
comply with the instructions on the sun
correct manner.
visor (see the "Supplementary Restraint
39) Use both hands to lift the bonnet.
Before lifting, check that the windscreen
74
F0S1130
System (SRS) - Airbag" chapter in the
wiper arms are not raised from the
"Safety" section).
windscreen, that the car is stationary and
SUN VISORS
that the parking brake is applied.
They are located at the sides of the
USB INPUT
interior rear-view mirror (fig. 75).
(where provided)
They can be adjusted forwards and
The car can be equipped with three
sideways.
USB ports. The port located on
To direct the visor laterally, detach the
the dashboard ((A) fig. 76) for data
visor from the interior rear-view mirror
transfer to the Uconnect™ system
side support and turn it towards the
and for charging external devices, the
side window.
USB port inside the central console
Courtesy mirrors are located on the
((B) fig. 77) and on the dashboard,
back of the sun visors.
next to the smartphone holder (where
provided) (D) fig. 78 for charging
external devices only.
68
WARNING After using a USB charging
port, we recommend disconnecting the
device (smartphone), always removing
the cable from the port of the car first,
never from the device. Cables left
flying or connected incorrectly could
compromise correct recharging and/or
the USB socket condition.
76
F0S1137
NOTE The USB port handles
79
F0S0844
data transmission from the Pen
Drive/Smartphone, etc. and slow
On versions provided with "smoker's
recharging of an external device, which
kit" optional equipment, the cigar lighter
is not guaranteed as it depends on the
is fitted instead of the power socket.
device type/brand.
POWER SOCKET
WARNING Do not connect devices
with powers higher than 180W to the
(for versions/markets where provided)
socket. Do not damage the socket by
This is located on the central console
using unsuitable adaptors.
and only works with the ignition device
in the ENGINE position. To use it, open
77
F0S1132
COMPARTMENT ON
cap (C) fig. 77.
CENTRAL TUNNEL
An additional D power socket (D) fig. 79
located in the luggage compartment is
D
available on some versions.
78
F0S1228
80
F0S1133
69
In the central tunnel there is a storage
To access the front cup holder/can
(A) - VOL: Turn the wheel up or down
compartment. To access it, grab the
holder open the door using the handle
to turn volume up or down of the
handle (A) fig. 80 and push the cover
(A) fig. 82.
Uconnect™system. A short press on
back. A second USB port is provided
the control mutes the system, a long
inside the compartment on some
press turns it off.
versions.
(B)- e-MODE. push or pull the lever
to select the different driving modes
FRONT ARMREST
(NORMAL, RANGE, SHERPA).
(where provided)
82
F0S1134
84
F0S1136
81
F0S1328
SMARTPHONE MOUNT
(CRADLE)
There may be an armrest with
(where provided)
integrated storage compartment
41)
between the front seats.
83
F0S1135
There is a mount (A) fig. 85 on the
To access the compartment, pull the
lever upwards (A) fig. 81 and lift the
dashboard for your smartphone;
There is also a storage compartment
always use it in order to interact with
armrest.
on the back (C) fig. 83.
your smartphone safely.
CUP HOLDERS / CANS
VOLUME AND "e-MODE"
AND HOLDERS
ADJUSTMENT
On the central tunnel there are two
CONTROLS
cup/can holders, a retractable one on
There are the following controls (fig. 84)
the front part of the armrest ((A) fig. 82)
on the central console:
and one on the back ((B) fig. 83).
70
charging phase, this will automatically
not all closed correctly and the engine
be interrupted.
is not on.
The wireless charging system is
A
enabled when the car is in running
WARNING Do not place contactless
condition and the vehicle battery is
cards (RFID), credit cards or metal
sufficiently charged.
objects in the charging compartment.
By interacting with the wireless charger
system and placing the mobile phone
WARNING To avoid damaging or
in the specific housing, the user will
tearing the surface of the charging
85
F0S1210
be informed by means from LED
compartment, do not place sharp
(A) fig. 87indicating the state of the
and/or pointed objects or objects other
WIRELESS CHARGING
wireless charging system:
than a mobile phone in it.
SYSTEM- WCPM
"Your phone is being charged" blue
(Wireless Charge Pad
LED: this is displayed when the mobile
WARNING Not all mobile phone covers
Module)
phone is positioned correctly in the
guarantee the correct charging of
(where provided)
wireless charging compartment and the
the phone. Check that charging is in
The wireless charger system is
system is activated correctly;
progress after having placed the phone
activated automatically when a mobile
"Phone fully charged" green LED: this
in the charging compartment.
phone Qi® standard compatible is
is displayed when the mobile phone
placed in the storage compartment (A)
has completed charging its battery (if
NOTE The use of multiple wireless
in fig. 86 on the central tunnel.
suitable to transmit the information);
"Object not allowed" red LED: this
functions on the smartphone at the
same time (Apple CarPlay/Android
is displayed when a phone that is not
Auto and wireless charging), as
enabled for wireless charging or an
indicated by the smartphone
object that is not permitted (e.g. the
ignition key) is placed (e.g. ignition key,
manufacturers, could cause it to
overheat, resulting in a limitation of the
credit card, a coin);
active functions or its turning off. In this
"System error" red LED: this appears
case, it is recommended to connect
when there is a malfunction in the
wireless charger system;
the system using the USB socket.
"System not active" LED off: there
Correct positioning of the mobile
86
F0S1138
are no objects in the compartment
phone
and/or the ignition device of the car in
To start charging wirelessly correctly,
If the mobile phone is removed from
the OFF position and/or the doors are
make sure your mobile phone is
the housing during the wireless
71
positioned completely within the green
ATTENTION: Use this product only
dotted area in fig. 87 with the display
for its intended use as described in
facing up and that the device does not
this manual without tampering with or
cover the alert LED (A).
modifying the product in any way.
Correct positioning: see fig. 88 (the
Unintended use or damage of the
LED identifies the positioning limit of
product may result in the exposure to
the device);
dangerous UV radiation. Even in small
incorrect positioning: see fig. 89;
doses, UV radiation can cause harm to
the eyes and skin.
WARNING: The UV-C light is
89
F0S1362
intended for use ONLY IN GLOVEBOX.
UV-C LIGHT
Under no circumstances should this
(where provided)
product be operated with humans,
plants, animals or living things.
It is located on the top of the glovebox.
ATTENTION: KEEP OUT OF REACH
The UV-C Light Operating Switch is
OF CHILDREN. Do not allow the device
located in the Central Console.
to be used as a toy.
Warnings & Disclaimers
ATTENTION: Ensure the Glove box
87
F0S1360
For your SAFETY and PROTECTION,
door is fully closed before starting the
it is very important for you to read and
operation.
understand this user manual before
ATTENTION: Don’t try to override the
use. Please pay particular attention
operation & expose yourself to UVC
to WARNING and CAUTION sections
Light.
as they are designed to call particular
ATTENTION: UV lamps are hot
attention to potential dangers when
during and after use - Do not touch.
using the UV-C light.
The UV-C light is designed to use UV
Read and save all notices, warnings
light to hygenize surface areas inside
and safety instructions received with
the glovebox. No chemicals are used in
the UV-C light.
this process.
88
F0S1361
ATTENTION: This UV-C light is
The surfaces must be exposed
equipped with ultraviolet lamps. UV
directly to the UV rays to be sanitized.
radiation is harmful to the eyes and
These rays do not penetrate materials
skin. Do not attempt to observe the UV
such as fabric, paper or glass,
lamps directly.
therefore make sure that the objects
72
to be sanitized are not located below
position. If the Engine is stopped during
smartphone Always follow the highway
these materials
the UV-C in operation, the cycle will be
code of the country in which you are
Any objects located in the storage
interrupted.
driving, and concentrate on the road.
Always drive safely with your hands on
compartment for sanitation must
OPERATING INSTRUCTIONS
the steering wheel. Only use the functions
be repositioned as many times as
The UV-C Operating Switch has a Uni-
of the system and the Fiat Smart Audio
necessary to guarantee that the UV-C
Apps when you are sure that it is safe to
colour LED (BLUE) indicator.
light strikes every surface of the item
do so. The customer is liable for all risks
The LED switches on as the switch is
Only use it in the specified operating
associated with using the functions and
pressed to START the operation.
applications of the car. Failure to follow
temperature range from -40 ⁰C to +80
The LED remains solid until the
these rules may cause serious accidents
⁰C (40 ⁰F to 176 ⁰F). Equipment failure
operation is COMPLETED, interrupted
and/or death.
or damage may occur outside of the
or stopped.
specified temperature range.
The LED shows No light + 1 Chime
Opportunities for infection are
ROOF RACK/SKI
if the operation is Successfully
abundant and virtually everywhere. Use
RACK
completed; one UVC complete cycle is
of the UV-C light does not guarantee
nearly 3min.
42) 43) 44)
that the user will avoid illness.
The LED shows Blinking for 5
The UV-C light is not intended for
26) 27)
seconds if the operation is interrupted
medical use.
or stopped.
FASTENERS
The frequent exposure to UVC light
The UV-C light will be ready for the
The fasteners are located in the zone
can cause early fading of the colours of
new cycle after the blinking is stopped.
indicated in fig. 90.
the goods
Two use the attachments, two
Do not use if the device is damaged,
threaded nuts (A) are provided, which
not working properly or has broken
WARNING
can be reached when the door is open.
lamps.
For optimal effectiveness, the UV
40) Do not travel with the storage
lamps must be free of fingerprints,
compartments open: they may injure the
sweat, dust accumulated over time,
front seat occupants in the event of an
etc. If hands accidentally come into
accident.
contact with the UV lamp, clean it
41) With the vehicle in motion, the
with a lint-free cloth and in any case
smartphone may only be used in the
periodically remove the dust that
upright position and only with the Fiat
Smart Audio App. The smartphone may
deposits on it
be placed in a horizontal position only
NOTE NOTE UV-C light only works
when the vehicle is stationary. Avoid
with the ignition device in the ENGINE
distractions while driving by using the
90
F0S1336
73
WARNING Follow the instructions
RED SPECIAL
SOUND SYSTEM
contained in the assembly kit carefully.
SERIES
28)
Assembly must be performed by
(where provided)
The basic audio system is composed
qualified personnel.
Some components of the
of:
car underwent antimicrobial
two woofers, diameter 165 mm, on
WARNING Travelling with the rack/ski
treatments, as detailed below. No
the front doors
rack fitted impacts on the life of the
specific precautions are required
two tweeter speakers, 19 mm
high-voltage battery.
for the normal use of the car and
diameter, in the front pillars
components treated with biocide
The medium sound system is
substances.
composed of:
WARNING
The boot mat was treated with a
two woofers, diameter 165 mm, on
biocide substance having antiviral
the front doors
42) Fully comply with the regulations in
properties based on the active
two tweeter speakers, 19 mm
force concerning maximum clearance.
Never exceed the maximum permitted
ingredient Silver Chloride.
diameter, in the front pillars
loads (see "Technical specifications"
The seat fabrics were treated with
two full range speakers, 130 mm
section).
a biocide substance having antiviral
diameter, in the rear side panels
43) Evenly distribute the load and take
and antibacterial properties based on
The premium sound system is
into account, when driving, the increased
the active ingredient Alkyl (C12-C16)
composed of:
responsiveness of the car to side wind.
After travelling for a few kilometres, check
Dimethylbenzyl Ammonium Chloride.
two Hi-Fi woofers, diameter 165 mm,
to ensure that the fixing screws for the
The steering wheel upholstery was
on the front doors
attachments are well tightened.
treated with biocide substances having
two Hi-Fi tweeter speakers, diameter
44) Before driving, make sure that the
antibacterial and antifungal properties
19 mm, in the front pillars
transversal bars have been fitted properly.
based on the active ingredients Zinc
two Hi-Fi full range speakers,
Pyrithione and Thiabendazole.
diameter 130 mm, in the rear side
IMPORTANT
The air cleaner of the climate control
panels
system was treated with a biocide
one 200 mm subwoofer
26) The use of transversal roof bars
substance having antibacterial and
an 8-channel digital amplifier
prevents the use of the sunroof, because
antiviral properties based on the active
Depending on the version, the aerial
the latter, while opening, interferes with the
ingredient Dimethyltetradecyl[3-
may be on the rear window or on the
bars. Therefore do not move the sunroof if
(trimethoxysilyl)propyl]ammonium
rear side window, for convertible
transversal bars have been fitted.
chloride.
versions.
27) The maximum load on the roof rack is
50 kg.
74
IMPORTANT
28) The maximum load on the subwoofer
is 40 kg. It is advisable to avoid
concentrated loads
75
KNOWING THE INSTRUMENT PANEL
This section of the handbook provides
INSTRUMENT PANEL
all information that is useful for getting
FEATURES
77
to know, interpreting, and using the
DISPLAY
78
instrument panel correctly.
WARNING LIGHTS AND
MESSAGES
86
76
INSTRUMENT PANEL FEATURES
B
B
A
A
D
C
91
F0S1070
A. Warning lights B. Engaged gear, seat belt status and status of driver assistance and active safety systems notification area C.
Speedometer D. Multi-function dial indicator: speedometer and driver assistance system indication
77
DISPLAY
MAIN SCREEN
O
E
N
M
A
D
OFF
B
L
L
C
I
D
F
G
H
92
F0S1071
The main screen fig. 92 shows the following information:
A. Driving assistance and active safety system notifications B. High-voltage battery charge level and range C. Failure icons D.
External temperature E. Multifunctional dial indicator and driving assistance system notifications F. Compass (where provided)
G. Speedometer H. Odometer I. Amber notification or failure indication icons L. Energy management M. Gear engaged
notifications, headlight alignment and SBR (Seat Belt Reminder) N. TSR and ISA system indication (where provided) O. Cruise
Control / Adaptive Cruise Control / Speed Limiter / Intelligent Speed Assist target speed setting (where provided)
78
A-Drivingassistanceandactive
B-High-voltagebatterycharge
settings) and an indicator that indicates
safety system notifications
state of charge and range
any changes in expected range:
This position displays the status
by means of an up arrow and
A
B
icons of the various functions (where
a blue bar if the current driving style
provided), such as ACC (Adaptive
increases the range;
Cruise Control), AEB Control
by means of a down arrow and
(Autonomous Emergency Brake
a red bar if the current driving style
Control) or Lane Control, active safety
decreases the range.
systems, such as ESC (Electronic
In case the driving style does not
Stability Control), TSR (Traffic Sign
change the range, no graphic signals
Recognition) and ISA (Intelligent Speed
are displayed.
Assist) and thumbnails of the driving aid
C-Failureicons
systems.
93
F0S1072
All failure icons are displayed in this
Refer to the "Starting and Driving"
position. In case of multiple failures, the
section for more information about
In this position the state of charge of
display will be in succession.
the high-voltage battery is indicated
driving assistance systems.
D-Externaltemperature
by a percentage and a vertical bar
Refer to the "Safety" section for more
The external temperature is displayed
of height proportional to the state of
information about active safety devices.
in °C or °F depending on the display
charge of the battery (A) fig. 93. Both
settings.
indications are coloured according to
the state of charge:
range greater than 24 km: blue
range between 24 km and 16 km:
yellow
range lower than 16 km: red
When charging via a power socket,
the vertical bar is coloured green and
the symbols and
(B) fig. 93
appear. The height of the vertical bar is
proportional to the state of charge of
the battery.
The estimated remaining range is
indicated by a numerical value (in km
or miles, depending on the display
79
E-Multifunctionaldialindicator
H-Odometer
and driving assistance system
B
Kilometres or miles travelled
notifications
(depending on the display settings) are
displayed in position (H) fig. 92.
I-Ambernotificationorfailure
A
B
indication icons
The amber notification icons (e.g. brake
A
C
pedal pressure request) or failure signal
70
icons are displayed in succession (in
case of several notifications) in position
km/h
km/h
95
F0S1075
(I) fig. 92.
L-Energymanagement
Pressing and releasing the controls on
Through the display customisation
94
F0S1074
the steering wheel
/
will open
functions (see "Settings" paragraph),
an alternative display that indicates the
the energy management can be
The fig. 94 shows the current speed
driving mode instead of speed. The
displayed on the graduated scale (L)
and (B) whether one of the speed
driving style is indicated in real-time by
fig. 92:
control systems (Cruise Control,
a cursor that can be positioned in the
"POWER": the left side of the
Adaptive Cruise Control, Traffic Sign
following areas (see fig. 95):
indicator turns orange in proportion to
Recognition and Intelligent Speed
(A) "CHARGE": regeneration mode.
the power required by the electric
Assist) is active. The round bar (A) also
(B) "ECO": energy-saving driving.
motor.
provides visual signals for particular
(C) "POWER": more energy-efficient
"CHARGE": the right side of the
states of the selected speed control
performance driving.
indicator turns turquoise in proportion
system. Refer to the "Starting and
F-"Compass(whereprovided)
to the amount of regeneration of the
Driving" section for more information
For versions with Uconnect™ system
high-voltage battery.
about driving assistance systems.
with integrated navigator, in position (F)
"ECO": the indicator turns orange
fig. 92 the direction the car is travelling
and turquoise to indicate energy-saving
in is shown in real-time.
driving.
G - Speedometer
M - Gear engaged notifications,
The instantaneous speed of the car
headlight alignment and SBR (Seat
(in km/h or mph) is displayed in this
Belt Reminder)
position, which can also be displayed
In position (M) fig. 92 the following
at the top of the display.
information is displayed:
80
driving mode ("NORMAL", "RANGE",
In the centre zone: odometer (default
OK: Press the button to interact with
"SHERPA");
setting), Audio information (where
the screens. Press the button once
gear engaged (D, N, R, P);
provided), Phone information (where
to confirm your selection. Hold the
headlight alignment;
provided), time, external temperature,
button pressed for 1 second to reset
electrical system readiness at start-
date, compass (where provided) and
the displayed/selected functions.
up ("READY") warning;
car speed repetition (where provided).
DISPLAY PAGES
SBR (Seat Belt Reminder) system
On the right side: time (default setting),
You can navigate through the following
notifications. Refer to the “SBR system”
odometer, external temperature, date,
main and detail screens using the
chapter in the “Safety” section for more
compass (where provided), car status
controls on the left side of the steering
information.
(ON, OFF, RUN).
wheel:
N - TSR and ISA system indication
CONTROL BUTTONS
Screenshot list
(where provided)
These are located on the left side of the
Traffic Signal Recognition (TSR) speed
Main screen
steering wheel fig. 96.
limit alerts set on the Intelligent Speed
By pressing and releasing
/
They can be used to scroll through the
Assist (ISA) system are shown in
the user can choose to display:
display screens.
position (N) fig. 92.
the multifunction dial indicator
O-CruiseControl/Adaptive
showing the speed of the car
Cruise Control / Speed Limiter
or:
/ Intelligent Speed Assist target
the use of motor power or the
speed setting (where provided)
state of charge of the high-voltage
battery
The desired speed signal, set on Cruise
Control, Adaptive Cruise Control,
/
Trip A/B
Speed Limiter and Intelligent Speed
Assist systems is displayed in position
Press and release
/
:
(O) fig. 92.
Trip A
96
F0S1139
Trip B
Notifications bar
The lower part of the display is
Driver assist
/
: Press and release the
reconfigurable via the display menu.
buttons to access the main menu and
The following information can be
Vehicle info
to scroll the menu and the submenus
displayed on the left hand side: external
Press and release
/
:
rightwards or leftwards.
temperature (default setting), time,
Tyre pressure
After selecting the desired screen,
date, compass (where provided) and
Service (scheduled servicing)
press the
or
button to access
car speed repeat (where provided).
any detail screens.
81

 

 

 

 

 

 

 

Content      ..      1      2      3      ..