Chrysler Voyager. Manual - part 316

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  314  315  316  317   ..

 

 

Chrysler Voyager. Manual - part 316

 

 

TEST

ACTION

APPLICABILITY

3

Turn ignition off.
Disconnect the Driver Power Seat Horizontal Position Sensor Connector.
Disconnect the Memory Seat Mirror Module C1 Connector.
Measure the resistance of the Horizontal Position Signal circuit between the
Horizontal sensor and the Memory Seat Mirror Module connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

No

→ Repair the Horizontal Position Signal circuit for an open.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

4

Turn ignition off.
Disconnect the Memory Seat Mirror Module C1 connector.
Disconnect the Driver Power Seat Horizontal Position Sensor connector.
Measure the resistance of the Horizontal Position Signal circuit to ground.
Is the resistance below 1000 ohms?

All

Yes

→ Repair the Horizontal Position Signal circuit a short to ground.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn ignition off.
Ensure the Memory Seat Mirror Module is fully connected before proceeding.
Disconnect the Driver Power Seat Horizontal Position Sensor Connector.
Connect a jumper wire between Seat Sensor 5 volt Supply and Horizontal Position
Signal circuits.
Turn ignition on.
With the DRBIII

t select Body Memory Seat Sensors.

Read the Horizontal Position Sensor voltage.
Is the voltage above 4.5 volts?

All

Yes

→ Replace the Seat Track Assembly.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 6

6

If there are no possible causes remaining, view repair.

All

Repair

Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

7

Turn ignition off.
Disconnect the Memory Seat Mirror Module C2 connector.
Measure the resistance of the Seat Sensor 5 volt supply circuit to body ground.
Is the resistance below 100.0 ohms?

All

Yes

→ Repair the Seat 5 Volt Supply circuit for a short to ground.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 8

691

MEMORY SEAT

HORIZONTAL SENSOR OUT OF RANGE LOW —

Continued

TEST

ACTION

APPLICABILITY

8

Turn ignition off.
Disconnect the Memory Seat Mirror Module C2 connector.
Disconnect the Driver Power Seat Horizontal Position Sensor connector.
Measure the resistance of the Seat Sensor 5 Volt Supply wire between the Horizontal
Sensor connector and the C2 connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 9

No

→ Repair the Seat Sensor 5 Volt Supply circuit for an open.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

9

If there are no possible cause remaining, view repair.

All

Repair

Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

692

MEMORY SEAT

HORIZONTAL SENSOR OUT OF RANGE LOW —

Continued

Symptom:

LEFT MIRROR HORIZONTAL SENSOR OUT OF RANGE HIGH

When Monitored and Set Condition:

LEFT MIRROR HORIZONTAL SENSOR OUT OF RANGE HIGH

When Monitored:

Continuously when the PCI bus is active

Set Condition:

This code is set when the mirror sensor feedback to the Memory Seat

Mirror Module is greater than the mirror out of range high value stored in EEPROM. Code
will remain for 50 ignition cycles.

POSSIBLE CAUSES

LEFT MIRROR HORIZONTAL POSITION WIRE SHORTED TO VOLTAGE

LEFT MIRROR SENSOR GROUND WIRE OPEN

STORED DIAGNOSTIC TROUBLE CODE

LEFT MIRROR HORIZONTAL POSITION SIGNAL OPEN

LEFT POWER MIRROR

MEMORY SEAT MIRROR MODULE HORIZONTAL POSITION SIGNAL

MEMORY SEAT MIRROR MODULE SENSOR GROUND

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, erase the DTC from Memory Seat Mirror Module.

Operate the driver’s power seat and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRB check for the same DTC to reset in the MSMM.
Did the same DTC reset?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

2

Turn the ignition off.
Disconnect the Left Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Left Mirror Horizontal Position Signal circuit in the Left
Power Mirror harness connector.
Is the voltage between 4.5 and 5.5 volts?

All

Yes

→ Go To 3

No

→ Go To 6

693

MEMORY SEAT

TEST

ACTION

APPLICABILITY

3

Turn the ignition off.
Disconnect the Left Power Mirror connector.
Measure the resistance of the Left Mirror Sensor Ground circuit in the harness
connector to ground.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 4

No

→ Go To 5

4

If there are no possible causes remaining, view repair.

All

Repair

Replace the Left Power Mirror.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Left Power Mirror connector.
Disconnect the Memory Seat Mirror Module C1 connector.
Measure the resistance of Left Mirror Sensor Ground circuit between the Memory
Seat Mirror Module connector and the Left Power Mirror connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Memory Seat Mirror Module.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Repair the open Sensor Ground circuit.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

6

Turn the ignition off.
Disconnect the Left Power Mirror connector.
Disconnect the Memory Seat Mirror Module C1 connector.
Turn the ignition on.
Measure the voltage of Left Mirror Horizontal Position Signal circuit.
Is there any voltage present?

All

Yes

→ Repair the Left Mirror Horizontal Position Signal circuit for a

short to voltage.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the Memory Seat Mirror Module C1 connector.
Disconnect the Left Power Mirror connector.
Measure the resistance of the Left Mirror Horizontal Position Signal circuit from the
Left Power Mirror connector to the Memory Seat Mirror Module connector.
Is the resistance below 5.0 ohms?

All

Yes

→ Replace the Memory Seat Mirror Module.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

No

→ Repair the open Left Mirror Horizontal Position Signal wire.

Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.

694

MEMORY SEAT

LEFT MIRROR HORIZONTAL SENSOR OUT OF RANGE HIGH —

Continued

 

 

 

 

 

 

 

Content   ..  314  315  316  317   ..