Audi A4. Body repair manual - part 22
Front door trim
Console and trunk release switch,
removing
- Remove door trim page 70-3 .
- Remove bolts -2- (2x).
- Remove console -5-.
- Disconnect harness connector from switch -1-.
- Remove trim panel -4- together with switch -1-.
- Remove grommet -1-.
Front door trim
Door trim for trunk release switch,
cutting out
The area to be cut out -1- is indicated on door
trim.
- Cut out area using available tools.
- Install grommet -2-.
Front door trim
Switching speaker trim (Normal, Bose)
- Drill out old speaker trim -1- at -2- (4x).
- Insert speaker trim -1- from front and secure speaker trim -1- with clips
-3- (4x).
Rear door trim
Rear door trim
Component locations, overview
1 - Door trim
Removing installing page 70-25
2 - Clip locator
3 - Outer connecting piece
4 - Outer filler piece
5 - Rear door trim insulation
page 70-37
6 - Foam seal
7 - Inner filler piece
8 - Inner connecting piece
9 - Guide for locking knob
10 - Interior door handle
Removing page 70-27
11 - Trim panel
Removing page 70-36
12 - Window crank handle
Rear door trim
13 - Speaker (woofer)
Removing page 70-16
14 - Door warning and footwell lights
Removing page 70-33
Rear door trim
Rear door trim, removing and installing
- Remove bolt -1-.
Tightening torque: 1.5 Nm (13 in. lb)
- Pull handle shell -2- downward out of door trim -4-.
- Remove nut -3- (1x).
Tightening torque: 2.5 Nm (22 in. lb)
Vehicles with manual window crank page 70-28 .
- Remove bolts -1- (2x).
Tightening torque: 1.5 Nm (13 in. lb)
- Lift door trim -3- up and out of door shell.
- To install, bases -4- for detent notches -2- (7x) must be fully installed.
Note:
The Bowden cable for the inside door mechanism and the electrical
harness connectors are not disconnected until after removing door trim -3-
Rear door trim
- Pull Bowden cable -1- out of guide -2- and remove.
Note:
When installing, make sure that hook -3- faces upward.
- Disconnect electrical harness connectors.
Rear door trim
Interior door handle, removing
- Remove door trim page 70-25 .
- Press spring -2- in direction of arrow -A- and remove interior door
handle -1- toward front.
Rear door trim
Rear manual window crank, removing
and installing
- Press in flat side of flat-head screwdriver in direction of arrow -1-.
- Rotate flat-head screwdriver in direction of arrow -2-.
- Pull off cover in direction of arrow -3-.
- Remove bolt -1-.
Tightening torque: 2.5 Nm (22 in. lb)
- Remove manual window crank -2- and base -3-.
Rear door trim
Rear door manual window crank installation
position
Illustration shows left manual window crank (right-side is mirror of left).
A - Driving direction
a - Installation position with window closed, at 40
20
angle toward
rear.
Rear door trim
Release button, adjusting
- When locked, release lever must not project more than dimension -a-.
Dimension -a-: 0-2 mm countersunk
Rear door trim
Power window switch, removing and
installing
- Remove door trim page 70-25 .
- Remove insulation page 70-37 .
- Use screwdriver to remove retaining tabs -1-.
- Remove power window switches -2-.
Rear door trim
Bass speaker, removing
- Remove door trim page 70-25 .
- Remove insulation page 70-37 .
- Remove bolts -1- (3x).
Tightening torque: 1.5 Nm (13 in. lb)
- Remove bass speaker -2-.