Vauxhall Movano (2016 year). Instruction

-------------------------------------------------------------------------------------------------------------------------------------------------------------

124

Driving and operating

If the selector lever has been shifted

●

the stop-start system is instructionly

Fault

out of neutral (instruction transmission)

deactivated

If control indicator Ï illuminates

or N (instruction transmission

●

the bonnet is opened

yellow, there is a fault in the stop-start

automated) or other conditions are

●

the driver's seat belt is

system 3 90. A corresponding

not met, start using the ignition key.

unfastened and the driver's door

message also appears in the DIC

The green control indicator Ï will

is opened

3 92. Seek the assistance of a

extinguish in the instrument cluster

●

the engine temperature is too low

workshop.

when the engine is restarted.

●

the vehicle battery is discharged

If the selector lever is shifted out of

Parking

neutral (instruction transmission) or N

●

the brake vacuum is not sufficient

(instruction transmission automated)

●

the vehicle starts to move

before depressing the clutch first, a

9 Warning

●

the defrosting function is

restart will not take place.

activated

●

Do not park the vehicle on an

Restart of the engine by the stop-

●

the climate control system

easily ignitable surface. The

start system

requests an engine start

high temperature of the

exhaust system could ignite the

●

the predetermined timing has

The selector lever must be in neutral

surface.

been exceeded

(instruction transmission) or N (instruction

●

Always apply parking brake

transmission automated) to enable an

If an electrical accessory, e.g. a

without pressing release

automatic restart.

portable CD player, is connected to

button. Apply as firmly as

the power outlet, a brief power drop

If one of the following conditions

possible on a downhill slope or

during restart might be noticeable.

occurs during an Autostop, the

uphill slope. Depress brake

engine will be restarted automatically

If the Infotainment system is active,

pedal at the same time to

by the stop-start system. Control

audio sound may briefly be reduced

reduce operating force.

indicator Ï will flash green in the

or interrupted during the restart.

●

Switch off the engine.

instrument cluster during an

Warning chimes 3 93.

automatic engine restart.

●

If the vehicle is on a level

surface or uphill slope, engage

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

125

first gear. On an uphill slope,

Caution

turn the front wheels away from

the kerb.

To ensure safe operation of the air

If the vehicle is on a downhill

suspension system, do not exceed

slope, engage reverse gear.

the maximum permissible gross

Turn the front wheels towards

vehicle weight rating. Refer to

the kerb.

identification plate 3 204 or the

vehicle documents.

● Close the windows.

● Turn the ignition key to position

For further information on the air

0 and remove it. Turn the

suspension system, refer to the

steering wheel until the

operating instructions supplied.

steering wheel lock is felt to

The master switch is located on the

engage.

Master switch

door pillar.

Switch on to enable operation and

Lock the vehicle 3 21 and activate the

Caution

adjustment of the air suspension

anti-theft locking system 3 31 and

system.

anti-theft alarm system 3 31.

The air suspension system must

be switched off when the vehicle is

Air suspension

being towed, jump-started, raised

off the ground or transported.

Operates automatically when the

vehicle is driven. The air suspension

Do not switch off the air

system constantly adjusts the ride

suspension system when driving.

height according to the vehicle load.

Jump starting 3 193, Towing the

vehicle 3 195.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

126

Driving and operating

Remote control

With the engine running, press the

free operation. Ensuring sufficient

appropriate button for 2 seconds to

clearance and freedom from

adjust the suspension height.

obstacles is the responsibility of

Indicator light will flash intermittently

the driver.

while height adjustment is in progress

and illuminates when complete.

Instruction settings

If the ignition is switched on with

Instruction adjustment can only be

engine not running, the suspension

performed when the vehicle is

height can only be lowered.

stationary.

Notice

Select by pressing h for 2 seconds,

Handle with care, protect from

then R to raise, or S to lower.

moisture and high temperatures and

To exit, press any of the pre-

avoid unnecessary operation.

programmed buttons.

When increased ground clearance or

Pre-programmed settings

Notice

improved vehicle access is required,

Adjusts the suspension height to one

Obstacle detection is not available

the suspension can be raised or

of three pre-programmed positions.

during instruction adjustment.

lowered using the remote control.

l : lowered position

When a certain low speed is

k : normal position

Caution

exceeded or when the ignition is

j : raised position

switched off, height adjustment is

Ensure there is adequate

deactivated automatically and the

Caution

suspension height is returned to the

clearance and that there are no

obstructions when adjusting the

normal position.

If an obstacle is detected while

suspension height.

raising or lowering, the

Service mode

suspension height is returned to

The remote control unit is magnetic

When the vehicle is stationary, press

the normal position after a delay.

and may be fixed to any metal part of

i for 5 seconds to put the vehicle into

This does not guarantee damage-

the vehicle or stored in its holder.

service mode. The indicator light will

illuminate.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

127

When service mode has been

conditions. Autostop is not available

Engine exhaust

activated, the air suspension master

and fuel consumption may be higher

switch must be turned off.

during this period. The emission of

smells and smoke during this process

To exit service mode, press i again

9 Danger

is normal.

for 5 seconds.

Engine exhaust gases contain

Under certain driving conditions, e.g.

Fault

poisonous carbon monoxide,

short distances, the system cannot

which is colourless and odourless

clean itself automatically.

If a fault is detected, i will flash

and could be fatal if inhaled.

intermittently. If service mode has

If cleaning of the filter is required and

been activated and there is a fault, h,

If exhaust gases enter the interior

if previous driving conditions did not

S and R will flash simultaneously.

of the vehicle, open the windows.

enable automatic cleaning, it will be

Have the cause of the fault

indicated by illumination of control

Have the cause of the fault remedied

rectified by a workshop.

indicator A 3 87. Seek the

by a workshop.

assistance of a workshop

Avoid driving with an open load

immediately.

compartment, otherwise exhaust

gases could enter the vehicle.

Caution

Diesel particle filter

If the cleaning process is

The diesel particle filter system filters

interrupted, there is a risk of

harmful soot particles out of the

provoking severe engine damage.

exhaust gases. The system includes

a self-cleaning function that runs

Cleaning takes place quickest at high

automatically during driving without

engine speeds and loads.

any notification.

The filter is cleaned by periodically

Catalytic converter

burning off the soot particles at high

temperature. This process takes

The catalytic converter reduces the

place automatically under set driving

amount of harmful substances in the

exhaust gases.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

128

Driving and operating

Malfunction indicator light 3 87.

Caution

Fuel grades other than those listed

AdBlue

Avoid contact of the paintwork with

on page 3 151, 3 206 could

AdBlue.

General information

damage the catalytic converter or

In case of contact, rinse off with

electronic components.

The selective catalytic reduction

water.

Unburnt petrol will overheat and

(BlueInjection) is a method to

damage the catalytic converter.

substantially reduce the nitrogen

AdBlue freezes at a temperature of

Therefore avoid excessive use of

oxides in the exhaust emission. This

approx. -11 °C. As the vehicle is

the starter, running the fuel tank

is achieved by injecting a Diesel

equipped with an AdBlue pre-heater,

dry and starting the engine by

Exhaust Fluid (DEF) into the exhaust

the emissions reduction at low

pushing or towing.

system.

temperatures is ensured. The AdBlue

The designation of this fluid is AdBlue

pre-heater works automatically.

In the event of misfiring, uneven

Ⓡ. It is a non-toxic, non-flammable,

Adblue gauge

engine running, a reduction in engine

colourless and odourless fluid which

performance or other unusual

consists of 32% urea and 68% water.

problems, have the cause of the fault

Notice

rectified by a workshop as soon as

AdBlue Ⓡ is a registered trademark

possible. In an emergency, driving

of the Verband der

can be continued for a short period,

Automobilindustrie e.V. (VDA).

keeping vehicle speed and engine

speed low.

9 Warning

If control indicator Z flashes, the

permitted emission limits may be

Avoid contact of your eyes or skin

exceeded. Lift your foot off the

with AdBlue.

accelerator until Z stops flashing and

In case of eye or skin contact,

is steadily illuminated. Contact a

rinse off with water.

workshop immediately.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

129

The current fluid level remaining is

Refill the Adblue tank as soon as

After the prevention of an engine

shown in the Adblue gauge 3 80.

possible. Refer to "Refilling AdBlue"

start, a warning message is displayed

below.

in the Driver Information Centre

Level warnings

reminding the driver that AdBlue level

Driving is possible without any

is insufficient.

The AdBlue consumption is approx.

restrictions.

1.5 litres per 1000 km and depends

To allow the engine to be restarted,

If AdBlue is not refilled within a certain

on the driving behaviour.

the tank should be filled with at least

distance, further level warnings are

10 litres of AdBlue.

displayed in the Driver Information

Version with level warnings in the

Centre depending on the current

High emission warnings

Driver Information Centre

AdBlue level.

If the exhaust emission rises above a

If the AdBlue level falls below a

Engine restarts prevented

certain value, warnings similar to the

certain value, a level warning will be

Subsequent requests to refill AdBlue

range warnings as described above

displayed in the Driver Information

and finally the announcement that an

will be displayed in the Driver

Centre 3 92.

engine restart will be prevented are

Information Centre. Control indicator

displayed in the Driver Information

Õ illuminates continuously together

Centre.

with A 3 87 and a warning chime.

Notice

Requests to have the exhaust system

These restrictions are a legal

checked and finally the

requirement.

announcement that an engine restart

with be prevented are displayed in the

Before the prevention of an engine

Driver Information Centre.

restart, a warning message with

0 miles is displayed in the DIC,

Notice

indicating that after switching off the

These restrictions are a legal

ignition an engine restart will be

requirement.

prohibited.

At an AdBlue range of approx.

680 miles, a warning message is

Additionally, control indicator Õ

displayed in the Driver Information

illuminates continuously together with

a warning chime.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

130

Driving and operating

Centre showing the remaining

Refill the Adblue tank as soon as

If the fault is not rectified within a

distance the vehicle can travel before

possible. Refer to "Refilling AdBlue"

certain distance, Õ and A flash for

engine restarts are prevented. This

below.

a few seconds then illuminate

warning message is repeated approx.

continuously. Loss of engine power.

Driving is possible without any

every 60 miles.

restrictions.

When the fault is critical, Õ and A

Seek the assistance of a workshop as

flash continuously and after the next

Engine power loss

soon as possible.

engine restart the vehicle speed will

As the Adblue level drops further,

control indicator Õ flashes for a few

be limited to approx. 12 mph.

Version without level warnings in the

seconds then illuminates

Driver Information Centre

Notice

continuously, accompanied by a

These restrictions are a legal

warning chime and loss of engine

requirement.

power.

Seek the assistance of a workshop as

Notice

soon as possible.

These restrictions are a legal

requirement.

Refilling AdBlue

If AdBlue is not refilled before the tank

is empty, Õ flashes and after the next

engine restart the vehicle speed will

be limited to approx. 12 mph.

Refill immediately with at least

10 litres of AdBlue.

When the Adblue gauge shows the

High emission warnings

level is very low, control indicator Õ

If the exhaust emission rises above a

first illuminates continuously, then as

certain value, control indicator Õ

Adblue level drops to a certain

illuminates together with A 3 87.

amount Õ flashes for a few seconds

Consult a workshop as soon as

then illuminates continuously.

possible.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

131

Notice

Filling station

Caution

When unscrewing the protective cap

from the filler neck, ammonia fumes

9 Danger

Only use AdBlue that complies

may emerge. Do not inhale as the

with European standards

fumes have a pungent smell. The

Follow the operating and safety

DIN 70 070 and ISO 22241-1.

fumes are not harmful by inhalation.

instructions of the filling station

Do not use additives.

when refilling Adblue.

The vehicle must be parked on a level

Do not dilute AdBlue.

surface.

1. Switch off engine and remove key

Otherwise the selective catalytic

The filler neck for AdBlue is located

from ignition switch.

reduction system could be

behind the filler flap located on the

damaged.

2. Pull filler flap to open.

right-hand side of the vehicle.

The filler flap can only be opened if

Notice

the vehicle is unlocked and the right-

If AdBlue must be refilled at very low

hand door is opened.

temperatures, the refilling of AdBlue

may not be detected by the system.

9 Danger

In this case, park the vehicle in a

space with a higher ambient

Vehicles with stop-start system:

temperature until AdBlue is

The engine must be switched off

liquefied.

and the ignition key removed, to

Notice

avoid risk of engine being

If engine starting is prohibited due to

restarted automatically by the

low Adblue level, we recommend

system.

adding a volume of at least 10 litres

3. Unscrew protective cap

of AdBlue when refilling. Avoid minor

Capacities 3 224.

anticlockwise from the filler neck.

top-ups (e.g. less than 5 litres),

4. Fully insert the pump nozzle into

otherwise the system may not detect

the filler neck and switch it on.

a refill.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

132

Driving and operating

5. When refilling is complete, mount

Notice

the protective cap and turn

Dispose of AdBlue canister and

clockwise until it engages.

hose according to environmental

requirements.

6. Close filler flap and right-hand

door.

Notice

Let the vehicle idle for 10 seconds to

AdBlue canister

allow the system to detect the

Notice

AdBlue refill.

Only use the designated AdBlue

Failure to observe this procedure will

canisters for refilling, to prevent a

result in the system only recognising

topping-up of too much AdBlue.

the AdBlue refill after 20 minutes of

Additionally, the fumes in the tank

driving.

are captured in the canister and do

3. Unscrew protective cap

If the AdBlue refill is detected

not emerge.

anticlockwise from the filler neck.

successfully, AdBlue level warnings

Notice

4. Open AdBlue canister.

will disappear.

Since AdBlue has a limited

5. Mount one end of the hose on the

If the AdBlue refill is not detected

durability, check the date of expiry

canister and screw the other end

some time after running the engine,

before refilling.

on the filler neck.

seek the assistance of a workshop.

1. Switch off engine and remove key

6. Lift the canister until it is empty.

Filler cap

from ignition switch.

7. Unscrew the hose from the filler

Only use genuine filler caps. Adblue

2. Pull filler flap to open.

neck.

tank has a special filler cap.

8. Mount the protective cap and turn

Fault

clockwise until it engages.

9. Close filler flap and right-hand

If the system detects an operating

door.

fault, control indicator Õ illuminates

together with A and a warning

chime. Seek the assistance of a

workshop immediately.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

133

Depending on version, a

Instruction transmission

Caution

corresponding message may also

appear in the Driver Information

It is inadvisable to drive with hand

Centre 3 92.

resting on the selector lever.

To engage reverse, with the vehicle

stationary depress the clutch pedal,

pull up the collar on the selector lever

and engage the gear.

If the gear does not engage, set the

lever to neutral, release the clutch

pedal and depress again; then repeat

gear selection.

Do not slip the clutch unnecessarily.

When operating, depress the clutch

pedal completely. Do not use the

pedal as a foot rest.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

134

Driving and operating

Always move the selector lever in the

Instruction transmission

Starting the engine

appropriate direction as far as it will

automated

Depress the brake pedal when

go. Upon release, it automatically

starting the engine. If the brake pedal

returns to the centre position.

is not depressed, T illuminates in the

The instruction transmission automated

: neutral

transmission display and the engine

(MTA) permits instruction (instruction

A/M : switch between automatic and

cannot be started.

mode) or automatic gear shifting

instruction mode

(automatic mode), both with

When the brake pedal is depressed,

The transmission display

automatic clutch control.

the transmission automatically shifts

shows "A" when in automatic

to N (neutral); "N" appears in the

mode.

transmission display and the engine

Transmission display

: reverse gear

can be started. There may be a slight

delay.

Engage only when vehicle is

stationary. The transmission

display shows "R" when

Selector lever

reverse gear is engaged.

: shift to a higher gear.

: shift to a lower gear.

Starting off

When the engine is started, the

transmission is in automatic mode.

Depress the brake pedal and move

the selector lever towards + to

engage first gear.

Shows the mode and current gear.

If R is selected, reverse gear is

engaged. The vehicle starts to move

when the brake pedal is released. To

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

135

start off quickly, release the brake

warning may sound as a signal to

Rocking the vehicle

pedal and accelerate immediately

depress the brake pedal or apply the

Rocking the vehicle is only

after engaging a gear.

parking brake.

permissible if the vehicle is stuck in

In automatic mode the transmission

Switch off engine if stopping for a

sand, mud, snow or a hole. Move the

shifts to other gears automatically,

lengthy period, e.g. in traffic jams.

selector lever between R and A/M (or

dependent on driving conditions.

When the vehicle is parked and the

between + and -) in a repeat pattern,

To engage instruction mode, move the

driver's door is opened, a warning

while applying light pressure to the

selector lever towards A/M. The

chime will sound if neutral is not

accelerator pedal. Do not race the

current gear will appear in the

selected or the brake pedal has not

engine and avoid sudden

transmission display.

been depressed.

acceleration.

To engage first gear, depress brake

Engine braking

Parking

pedal and move selector lever

towards + or -. Shift to a higher or

Apply the parking brake. The most

Automatic mode

lower gear by moving selector lever to

recently engaged gear (see

When driving downhill, the instruction

+ or -. Gears can be skipped by

transmission display) remains

transmission automated does not

moving the selector lever repeatedly

engaged. With N, no gear is engaged.

shift into higher gears until a fairly

at short intervals.

high engine speed has been reached.

When the ignition is switched off, the

It shifts down in good time when

transmission no longer responds to

Stopping the vehicle

braking.

movement of the selector lever.

In automatic or instruction mode,

If the ignition is not switched off, or the

first gear is engaged and the clutch is

Instruction mode

parking brake has not been applied, a

released when the vehicle is stopped.

To utilise the engine braking effect,

warning chime will sound upon

In R, reverse gear remains engaged.

select a lower gear in good time when

opening the driver's door.

driving downhill.

When stopping on gradients, engage

parking brake or depress the brake

Instruction mode

pedal. To prevent overheating of the

clutch, an intermittent audible

If a higher gear is selected when the

engine speed is too low, or a lower

gear when the speed is too high, the

-------------------------------------------------------------------------------------------------------------------------------------------------------------

136

Driving and operating

shift is not executed. This prevents

Activate the Winter mode if you have

Laden mode kg

the engine from running at too low or

problems starting off on a slippery

too high an engine speed.

road surface.

If engine speed is too low, the

Activation

transmission automatically shifts to a

Press V. Control indicator V is shown

lower gear.

in the transmission display. The

If engine speed is too high, the

transmission switches to automatic

transmission only switches to a higher

mode and the vehicle starts off in a

gear via kickdown.

suitable gear.

Deactivation

Electronic driving

The Winter mode is switched off by:

programmes

● pressing V again

Winter mode V

● turning off the ignition

It is possible to use the Laden mode

in both manual and automatic modes.

● switching to manual mode

In both cases, the gearshifting

In order to protect the transmission at

patterns are adapted automatically

extremely high clutch temperatures,

for carrying an increased payload.

an intermittent audible warning may

sound. In such cases, depress the

Activation

brake pedal, select "N" and apply the

Press kg. Control indicator kg is

parking brake to allow the clutch to

shown in the transmission display.

cool down.

The transmission will then select

optimized gearshift patterns.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Driving and operating

137

Deactivation

Interruption of power supply

Brakes

The Laden mode is switched off by:

The clutch is not disengaged if there

● pressing kg again

is an interruption of the power supply

The brake system comprises two

● turning off the ignition

when a gear is engaged. The vehicle

independent brake circuits.

cannot move.

If a brake circuit fails, the vehicle can

Kickdown

If the vehicle battery is discharged,

still be braked using the other brake

start the vehicle using jump leads

circuit. However, braking effect is

If the accelerator pedal is pressed

3 193.

achieved only when you depress the

past the pressure point, the

brake pedal firmly. You need to use

transmission shifts to a lower gear

If the cause of the fault is not a

considerably more force for this. The

depending on engine speed. Full

discharged vehicle battery, seek the

braking distance is extended. Seek

engine power is available for

assistance of a workshop.

the assistance of a workshop before

acceleration.

If neutral cannot be selected, the

continuing your journey.

If engine speed is too high the

vehicle must only be towed with the

When the engine is not running, the

transmission switches to a higher

drive wheels raised off the ground

support of the brake servo unit

gear, even in manual mode. Without

3 195.

disappears once the brake pedal has

kickdown this automatic shift is not

Towing the vehicle 3 195.

been depressed once or twice.

effected in manual mode.

Braking effect is not reduced, but

braking requires significantly greater

Fault

force. It is especially important to bear

In the event of a fault, control indicator

this in mind when being towed.

W is shown in the transmission

Control indicator R 3 88.

display. Continued driving is possible

provided the vehicle is driven with

Antilock brake system

care and anticipation.

Antilock brake system (ABS)

Have the cause of the fault remedied

prevents the wheels from locking.

by a workshop.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

138

Driving and operating

ABS starts to regulate brake pressure

Parking brake

9 Warning

as soon as a wheel shows a tendency

to lock. The vehicle remains

If there is a fault in the ABS, the

steerable, even during hard braking.

wheels may be liable to lock due

ABS control is made apparent

to braking that is heavier than

through a pulse in the brake pedal

normal. The advantages of ABS

and the noise of the regulation

are no longer available. During

process.

hard braking, the vehicle can no

For optimum braking, keep the brake

longer be steered and may

pedal fully depressed throughout the

swerve.

braking process, despite the fact that

the pedal is pulsating. Do not reduce

If control indicators u, A, R and

the pressure on the pedal.

C illuminate, the ABS and ESP are

Control indicator u 3 88.

deactivated and the message

BRAKING FAULT is shown in the

Warning

Fault

DIC. Seek the assistance of a

workshop.

Always apply parking brake firmly

If control indicators u and A

Have the cause of the fault remedied

without operating the release

illuminate with the messages CHECK

by a workshop.

button, and apply as firmly as

ABS and CHECK ESP in the Driver

possible on a downhill or uphill

Information Centre (DIC), there is a

slope.

fault in the ABS. The brake system

remains operational but without ABS

To release the parking brake, pull

regulation.

the lever up slightly, press the

release button and fully lower the

lever.

To reduce the operating forces of

the parking brake, depress the

brake pedal at the same time.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

139

Driving and operating

Control indicator R 3 88.

Brake assist

Caution

Parking 3 124.

If the brake pedal is depressed

quickly and forcefully, maximum

The Hill start assist cannot

Retractable parking brake

brake force is automatically applied

completely prevent vehicle

(full braking).

movement in all situations

(extremely steep gradients, etc.).

Maintain steady pressure on the

brake pedal for as long as full braking

If necessary, depress the brake

is required. Maximum brake force is

pedal to prevent the vehicle from

automatically reduced when the

rolling forwards or backwards.

brake pedal is released.

Brake assist is not available during an

The Hill start assist is not active

Autostop. Stop-start system 3 122.

during an Autostop. Stop-start system

3 122.

Hill start assist

The system helps prevent unintended

Depending on vehicle, the parking

movement when driving away on

brake lever retracts to the horizontal

inclines.

position even with the parking brake

When releasing the brake pedal after

applied.

stopping on an incline (with the

To release the parking brake, pull the

selector lever in a forward gear or

lever up slightly, press the release

reverse gear), the brakes remain on

button and return the lever to the

for a further 2 seconds. The brakes

horizontal position.

release automatically as soon as the

vehicle begins to accelerate.

To apply the parking brake, pull the

lever up and release it. The lever rests

in a horizontal position.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

140

Driving and operating

If necessary, in the event of soft

Ride control systems

9 Warning

ground, mud or snow-covered road

surfaces, the Traction control system

Traction Control system

Do not let this special safety

(TC) can be deactivated to enhance

The Traction Control system (TC) is a

feature tempt you into taking risks

traction:

component part of the Electronic

when driving.

Press Ø on the instrument panel.

Stability Program (ESP®^Plus) which

Adapt speed to the road

improves driving stability when

conditions.

necessary, regardless of the type of

road surface or tyre grip, by

Control indicator b 3 89.

preventing the drive wheels from

Trailer stability assist (TSA) 3 155.

spinning.

As soon as the drive wheels starts to

Enhanced Traction function

spin, engine output is reduced and

the wheel spinning the most is braked

individually. This considerably

improves the driving stability of the

vehicle on slippery road surfaces.

TC is operational as soon as the

ignition is switched on and control

Control indicator Ø illuminates in the

indicator b extinguishes in the

instrument cluster and a

instrument cluster. A corresponding

corresponding message appears in

message also appears in the Driver

the DIC 3 92.

Information Centre (DIC) 3 92.

When vehicle speed reaches

When TC is active b flashes.

30 mph, the system switches

automatically from Enhanced

Traction function to TC operation.

Control indicator Ø extinguishes in

the instrument cluster.

Vauxhall Movano (2016 year). Instruction - part 8