Vauxhall Movano (2016 year). Instruction

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

Illuminates briefly when the ignition is

Do not remove key until vehicle is

switched on.

stationary, otherwise the steering

wheel lock could engage

Illuminates

Illuminates when the engine is

unexpectedly.

running

Tyre pressure loss. Stop immediately

and check tyre pressure.

Check oil level before seeking

Caution

assistance of a workshop 3 160.

Control indicator w illuminates

together with C 3 88 and a

Engine lubrication may be

corresponding message appears in

Low fuel

interrupted. This may result in

the Driver Information Centre (DIC)

damage to the engine and/or

Y illuminates yellow.

when a puncture or severely under-

locking of the drive wheels.

inflated tyre is detected.

Illuminates when the ignition is

switched on and extinguishes shortly

1. Depress clutch.

Flashes

after the engine starts.

2. Select neutral gear, set selector

Fault in system. After a delay the

lever to N.

Illuminates when the engine is

control indicator illuminates

3. Move out of the flow of traffic as

running

continuously. Consult a workshop.

quickly as possible without

Fuel level in the tank is too low. Refuel

Control indicator w illuminates

impeding other vehicles.

immediately.

together with A 3 87 and a

4. Switch off ignition.

corresponding message appears in

Never run the tank dry.

the DIC when a tyre without a

Refuelling 3 152.

9 Warning

pressure sensor is mounted (e.g.

Catalytic converter 3 127.

spare wheel).

When the engine is off,

Bleeding the diesel fuel system

Tyre pressure monitoring system

considerably more force is needed

3 166.

3 182.

to brake and steer. During an

Autostop the brake servo unit will

Stop-start system

Engine oil pressure

still be operational.

I illuminates red.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

Illuminates when an Autostop is

Cruise control, Speed limiter 3 142.

High beam assist

inhibited when certain conditions are

í illuminates when the high beam

not fulfilled.

assist is activated 3 98.

Tachograph

Ï illuminates or flashes yellow /

& illuminates when there is a fault

green.

3 96.

Fog light

Illuminates

> illuminates green.

Door open

Illuminates green during an Autostop.

Illuminated when the front fog lights

are on 3 100.

y illuminates yellow.

If Ï illuminates yellow there is a fault

in the stop-start system. Seek the

Illuminates with the ignition switched

assistance of a workshop.

on when a door or the load

Rear fog light

compartment is open.

Flashes

ø illuminates yellow.

Depending on version, control

Illuminated when the rear fog light is

Flashes green during an automatic

indicator also illuminates in

on 3 101.

restart.

transmission display, indicating

relevant open door.

Stop-start system 3 122.

Cruise control

m, U illuminates green or yellow.

Exterior light

m illuminates green when a certain

9 illuminates green.

speed is stored.

Illuminated when the exterior lights

U illuminates green when the system

are on 3 97.

is on.

High beam

Speed limiter

P illuminates blue.

U illuminates yellow.

Illuminated when high beam is on and

U illuminates yellow when the

during headlight flash 3 98.

system is on.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

● vehicle messages 3 92

Information displays

Vehicle messages

● trip computer 3 94

Driver Information Centre

Some of the displayed functions differ

Messages appear in the Driver

when the vehicle is being driven or at

Information Centre (DIC), in

The Driver Information Centre (DIC)

a standstill. Some functions are only

combination with control indicator

is located in the instrument cluster

available when the vehicle is being

A or C.

below the speedometer.

driven.

Information messages

Info display

Information messages

Displays time, outside temperature

BATTERY MODE: ECONOMY

and Infotainment system information

when the ignition is on.

ESP OFF

For further information, see

Infotainment instruction.

AUTO LIGHTS DEACTIVATED

OIL LEVEL CORRECT

Fault messages

Depending on vehicle configuration,

the following items appear in the

Displayed in combination with control

display:

indicator A. Drive with caution and

● outside temperature 3 77

seek the assistance of a workshop.

To remove fault message, press

● clock 3 77

button on end of wiper lever. After a

● odometer, trip odometer 3 80

few seconds the message may

● engine oil level monitor 3 81

disappear automatically and A

● service display 3 82

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

remains illuminated. The fault will

Tyre pressure monitoring system

● If the sliding door is open and the

then be stored in the on board

3 182.

parking brake is released 3 26.

system.

● During activation and

Fault messages

Warning chimes

deactivation of alarm monitoring

of vehicle inclination 3 31.

CHECK ESP

When starting the engine or whilst

● If the AdBlue level falls below a

driving

certain amount or a fault is

CHECK FUEL FILTER

present 3 128.

Only one warning chime will sound at

a time.

● If the lane departure warning

CHECK GEARBOX

system detects an unintended

The warning chime regarding

lane change and when the

CHECK AUTO LIGHTS

unfastened seat belts has priority

system is activated 3 150.

over any other warning chime.

●

If seat belt is not fastened 3 49.

When the vehicle is parked and/or

Warning messages

●

If a certain speed is exceeded

the driver's door is opened

These may appear with control

with the parking brake applied

indicator C or in combination with

● When the key is in the ignition

3 138.

other warning messages, control

switch.

●

If the parking assist detects an

indicators or an audible warning. Stop

● With exterior lights on.

object or a fault is present

engine immediately and seek the

3 146.

● If the vehicle has instruction

assistance of a workshop.

transmission automated 3 134;

●

If the vehicle has instruction

Warning messages

the parking brake has not been

transmission automated and the

applied, neutral is not selected or

INJECTION FAULT

clutch temperature is too high

the brake pedal has not been

3 134.

depressed. A corresponding

ENGINE OVERHEATING

●

If the vehicle speed briefly

message may also appear in the

exceeds a set limit 3 79.

Driver Information Centre (DIC)

GEARBOX OVERHEATING

●

During closing of the power

3 92.

sliding door 3 26.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

●

If the sliding side door exterior

● average speed

Trip computer

handle is in the open position

● distance before service 3 82

when unlocking the vehicle 3 26.

The trip computer provides

● clock 3 77

●

If the engine is in an Autostop but

information on driving data, which is

● odometer 3 80, trip odometer

not switched off. Stop-start

continually recorded and evaluated

3 80

system 3 122.

electronically.

● cruise control and speed limiter

stored speed 3 142

● fault and information messages

Fuel used

Displays the amount of fuel

consumed since the last reset.

The measurement can be restarted at

any time by pressing and holding the

button on the end of the wiper lever.

Average consumption

Depending on vehicle, the following

The value is displayed after driving a

functions can be selected by pressing

distance of 0.25 miles.

button repeatedly on end of wiper

Average consumption is displayed,

lever:

taking into consideration the distance

● fuel used

travelled and the fuel used since the

last reset.

● average consumption

The measurement can be restarted at

● instantaneous consumption

any time.

● range

● distance travelled

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

Instantaneous consumption

The average speed since the last

Fuel economy rating (ecoScoring)

reset is displayed.

The value is displayed after reaching

If equipped, a rating of 0 to 100 is

The measurement can be restarted at

a speed of 20 mph.

shown in the display to help evaluate

any time.

fuel efficiency, based on your driving

Range

Interruptions in the journey with the

style.

ignition off are not included in the

The value is displayed after driving a

Higher ratings indicate better fuel

calculations.

distance of 0.25 miles.

economy.

The range is calculated from the

Reset trip computer information

Tips to improve fuel economy are also

current contents of the fuel tank and

given in the display. Journeys can be

To reset the trip computer, select one

the average consumption since the

saved in the system memory,

of its functions then press and hold

last reset.

enabling you to compare

button on end of wiper lever.

performances. Refer to Infotainment

The range will not display if control

The following trip computer

system instruction for further

indicator Y is illuminated in the

information will be reset:

information.

instrument cluster 3 90.

● fuel used

Vehicle messages 3 92.

The measurement can be restarted at

any time.

● average consumption

Journey record

● range

Distance travelled

When the engine is switched off, a

● distance travelled

record of the last journey is shown in

Displays the distance driven since the

● average speed

the display.

last reset.

The trip computer will reset

The following information is

The measurement can be restarted at

automatically when the maximum

displayed:

any time.

value of any of the parameters is

● average fuel consumption

exceeded.

Average speed

● trip odometer

The value is displayed after driving a

● fuel saved in miles

distance of 0.25 miles.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Instruments and controls

Interruption of power supply

Notice

Tachograph

When a tachograph is fitted, the total

If the power supply has been

distance travelled may be shown

interrupted or if the vehicle battery

only on the tachograph and not in the

voltage has dropped too low, the

odometer within the instrument

values stored in the trip computer will

display.

be lost.

Odometer 3 80.

The tachograph is operated as

described in the operating

instructions supplied. Observe

regulations regarding use.

Control indicator & illuminates in the

instrument cluster in the event of a

fault. Seek the assistance of a

workshop.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Lighting

Low beam control indicator 9 3 91.

Lighting

Exterior lighting

Tail lights

Light switch

Tail lights are illuminated together

Exterior lighting

with low beam and sidelights.

Light switch

Automatic light control

High beam

High beam assist

Headlight flash

Headlight range adjustment

Headlights when driving

abroad

Daytime running lights

Adaptive forward lighting

100

Hazard warning flashers

100

Turn and lane-change signals . 100

Turn outer light switch:

Front fog lights

100

: off

Rear fog lights

101

: sidelights

Reversing lights

101

9 P : headlights

Misted light covers

101

AUTO : automatic light control:

When the automatic light control

Interior lighting

101

headlights are switched on

function is switched on and the

Interior lights

101

and off automatically.

engine is running, the system

Load compartment lighting

102

switches between daytime running

Reading lights

102

Turn inner light switch:

lights (where fitted) and headlights,

Lighting features

103

> : front fog lights

depending on the lighting conditions.

Exit lighting

103

ø : rear fog lights

For reasons of safety, the light switch

Battery discharge protection

104

High beam control indicator P 3 91.

should always remain in the AUTO

position.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Lighting

Daytime running lights 3 99.

It switches to low beam when:

The control indicator í illuminates

continuously in the instrument cluster

● A sensor detects the lights of

Automatic headlight activation

when the assist is activated, while the

oncoming or preceding vehicles.

blue control indicator 7 3 91

During poor lighting conditions the

● It is foggy or snowy.

illuminates when high beam is on.

headlights are switched on.

● Driving in urban areas.

Control indicator í 3 91.

If there are no restrictions detected,

High beam

Notice

the system switches back to high

Use of the system does not relieve

beam.

the driver from full responsibility for

Activation

vehicle operation.

Deactivation

Push the turn signal lever forwards

again. Control indicator í

extinguishes.

High beam assist is also deactivated

when the outer light switch is moved

out of the AUTO position.

Notice

Depending on version, the system

To change between low and high

can be also be deactivated via the

beam, pull lever until a click is felt.

Infotainment system. Refer to

Infotainment system instruction for

Turn the outer light switch to AUTO

High beam assist

further information.

then push the turn signal lever

This feature allows high beam to

forwards to activate high beam assist.

function as the main driving light at

night and when vehicle speed is

faster than approx. 28 mph.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Lighting

General information

Headlight range adjustment

Headlights when driving

Performance of the system can be

abroad

Instruction headlight range

affected due to the following:

The asymmetrical headlight beam

adjustment

● Extreme weather conditions, e.g.

extends visibility at the edge of the

heavy rain, fog or snow.

road at the passenger side.

● The front camera or the

However, when driving in countries

windscreen is obstructed.

where traffic drives on the opposite

side of the road, adjust the headlights

● Oncoming or preceding vehicle

to prevent dazzling of oncoming

lights are not detected.

traffic.

● Headlights are not adjusted

Have the headlights adjusted by a

correctly.

workshop.

● Various reflective surfaces may

also cause the system to fail to

detect other vehicles.

Daytime running lights

Daytime running lights increase

Headlight flash

With low beam switched on, adapt the

visibility of the vehicle during daylight.

headlight range to suit the vehicle

The lights operate automatically

To activate the headlight flash, pull

load to prevent dazzling of oncoming

when the ignition is switched on.

lever.

traffic.

If the vehicle is equipped with the

Turn knurled wheel to required

automatic light control function, the

position:

system switches between daytime

0 : front seat occupied

running lights and headlights

4 : loaded up to permissible

automatically depending on the

maximum weight

lighting conditions. Automatic light

control 3 97.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

100

Lighting

In the event of hard braking, the

happen when making a minor

Adaptive forward lighting

hazard warning flashers may turn on

steering manoeuvre such as lane

Cornering light

automatically. Switch off by pressing

changing.

¨.

For three flashes, e.g. when changing

Depending on the steering angle,

lanes, move lever part way to first

vehicle speed and gear selected

Turn and lane-change

stop. When released, lever will spring

when cornering, an additional light

back.

will illuminate the corner of the road

signals

on the respective side.

If the lever is moved past the first stop,

the indicator is switched on

The cornering light is switched off

constantly. Switch the indicator off

automatically after prolonged use and

instructionly by moving the lever to its

at vehicle speeds above 25 mph.

original position.

Hazard warning flashers

Front fog lights

lever up

: right turn signal

lever down : left turn signal

When the steering wheel is turned

back, the lever automatically returns

to its original position and the

indicator is deactivated. This will not

Operated by pressing ¨.

Turn inner switch to position > and

release.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Lighting

101

Front fog lights operate with engine

Misted light covers

Interior lighting

running and headlights switched on.

The inside of the light covers may mist

up briefly in poor, wet and cold

Interior lights

Rear fog lights

weather conditions, in heavy rain or

Courtesy lights illuminate when the

after washing.The mist disappears

vehicle is unlocked with the remote

quickly by itself; to help, switch on the

control or the front doors are opened.

headlights.

When the doors are closed, the

courtesy light extinguishes after a

delay or immediately after the ignition

is switched on.

Front courtesy light

With the switch in its central position,

the light functions as a courtesy light.

Turn inner switch to position ø and

release.

Rear fog lights operate with engine

running and headlights switched on.

Reversing lights

The reversing lights come on when

the ignition is on and reverse gear is

selected.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

102

Lighting

Operated by pressing the switch c:

Reading lights l 3 102.

When the doors are closed, the

courtesy light extinguishes after a

● on constantly

delay or immediately after the ignition

● on when the doors are unlocked

Load compartment lighting

is switched on.

and opened

Load compartment lighting can be set

● off constantly

to illuminate when the side and rear

Reading lights

doors are opened, or switched on

Rear courtesy lights

constantly.

Front reading light

With the switch in its central position,

Combi, Bus

the light functions as a courtesy light.

Low level and overhead courtesy

lights are located in the rear

passenger compartment.

Operated with l.

The reading light can be directed as

Operated by pressing the switch c:

required, depending on version.

● on constantly

Operate rocker switch on the

● on when the doors are unlocked

instrument panel:

and opened

press OFF : off

● off constantly

press c

: on

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Lighting

103

Rear reading lights

Lighting features

Combi, Bus

Exit lighting

Each reading light can then be

switched on or off individually and

directed as required.

Operate rocker switch on the

Headlights come on for approx.

instrument panel:

30 seconds after the vehicle is parked

press l

: on

and the system is activated.

press OFF : off

Activating

Courtesy lights c 3 101.

1. Switch off ignition.

2. Remove ignition key.

3. Pull turn signal lever towards

steering wheel.

This action can be repeated up to

four times.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

Climate control

105

Temperature

Climate control

Climate control systems

red

: warm

Heating and ventilation

blue : cold

system

Climate control systems

105

Heating will not be fully effective until

Heating and ventilation system 105

the engine has reached normal

Air conditioning system

106

operating temperature.

Electronic climate control

system

107

Fan speed

Rear heating system

109

Adjust the air flow by switching the fan

Rear air conditioning system ... 110

to the desired speed.

Auxiliary heater

111

Air vents

115

Air distribution

Adjustable air vents

115

M : to head area

Fixed air vents

116

L : to head area and foot well

Glovebox cooler

116

K : to foot well

Maintenance

116

J : to windscreen, front door

Air intake

116

Controls for:

windows and foot well

Pollen filter

116

● temperature

V : to windscreen and front door

Air conditioning regular

windows

operation

117

● fan speed

Service

117

● air distribution

Intermediate settings are possible.

● demisting and defrosting

Demisting and defrosting the

Heated rear window Ü 3 37, Heated

windows

seats ß 3 45.

● Set temperature control to

warmest level.

● Set fan speed to highest level.

-------------------------------------------------------------------------------------------------------------------------------------------------------------

106

Climate control

● Set air distribution control to V.

Heated rear window Ü 3 37, Heated

Air recirculation system

seats ß 3 45.

● Switch on heated rear window Ü.

Operated by pressing u.

● Open side air vents as required

Cooling (A/C)

and direct them towards door

9 Warning

windows.

Operated by pressing A/C and

functional only when the engine and

● For simultaneous warming of the

The exchange of fresh air is

fan are running.

foot well, set air distribution

reduced in air recirculation mode.

control to J.

The air conditioning system cools and

In operation without cooling the air

dehumidifies (dries) the air when

humidity increases, so the

outside temperature is a little above

windows may mist up. The quality

Air conditioning system

the freezing point. Therefore

of the passenger compartment air

condensation may form and drip from

deteriorates, which may cause the

under the vehicle.

vehicle occupants to feel drowsy.

If no cooling or drying is required,

switch the cooling system off to save

Maximum cooling

fuel.

Briefly open the windows so that hot

Notice

air can disperse quickly.

If the climate control is set to

● Cooling A/C on.

maximum cooling while the ambient

● Air recirculation system u on.

temperature is high, an Autostop

may be inhibited until the required

● Set air distribution control to M.

temperature in the passenger

● Set temperature control to

compartment has been reached.

coldest level.

Additional to the heating and

If the climate control is set to

● Set fan speed to highest level.

ventilation system, the air

maximum cooling while the engine is

● Open all air vents.

conditioning system has controls for:

in an Autostop, the engine may

A/C : cooling

restart automatically.

: air recirculation

Stop-start system 3 122.

Vauxhall Movano (2016 year). Instruction - part 6