|
|
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 3: Test Conditions for Acrylonitrile/ Butadiene/Styrene (ABS)
ISO
2507-3
and Acrylonitrile/ Styrene/Acrylic Ester (ASA) Pipes and Fittings First Edition
ISO
2509
Sound-Absorbing Expanded Pure Agglomerated Cork in Tiles Second Edition
ISO
2510
Sound-Reducing Composition Cork in Tiles Second Edition
ISO
2528
Sheet Materials - Determination of Water Vapour Transmission Rate - Gravimetric (Dish) Method Second Edition
ISO
2531
Ductile Iron Pipes, Fittings, Accessories and Their Joints for Water or Gas Applications Fifth Edition
ISO
2532
Steel Wire Ropes - Vocabulary First Edition
Standard Atmosphere (Identical with the ICAO and WMO Standard Atmospheres from - 2 to 32 km) Atmosphere Type (Identique Aux
Atmospheres Standard De L'OACI Et De L'OMM Entre - 2 Et 32 km) First Edition; Erratum-1977; Amendment 1-1985; Amendment 2-
ISO
2533
1997
ISO
2534
Road Vehicles - Engine Test Code - Gross Power Second Edition; This Standard is Consistent with ISO 1585: 1992
ISO
2535
Plastics - Unsaturated-Polyester Resins - Measurement of Gel Time at Ambient Temperature Third Edition
ISO
2536
Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes and Fittings, Metric Series - Dimensions of Flanges First Edition
ISO
2537
Hydrometry ù Rotating-element currentmeters Fouth Edition
ISO
2538
Geometrical Product Specifications (GPS) - Series of Angles and Slopes on Prisms Second Edition
ISO
2540
Centre Drills for Centre Holes with Protecting Chamfer - Type B First Edition
ISO
2541
Centre Drills for Centre Holes with Radius Form - Type R First Edition
ISO
2543
Copper and Copper Alloys - Determination of Manganese - Spectrophotometric Method First Edition
ISO
2544
Textile Machinery and Accessories - Warping Machinery - Preparation of Warp for Weaving - Vocabulary First Edition
ISO
2549
Hand-Knotted Carpets - Determination of Tuft Leg Length Above the Woven Ground First Edition; Corrigendum 1-1990
ISO
2550
Hand-Made Carpets - Determination of Types of Knots First Edition
Machine-Made Textile Floor Coverings - Determination of Dimensional Changes Due to the Effects of Varied Water and Heat
ISO
2551
Conditions Second Edition
ISO
2553
Welded, Brazed and Soldered Joints - Symbolic Representation on Drawings Third Edition; Includes Draft Addendum 1
ISO
2554
Plastics - Unsaturated Polyester Resins - Determination of Hydroxyl Value Second Edition
Plastics - Resins in the Liquid State or as Emulsions or Dispersions - Determination of Apparent Viscosity by the Brookfield Test
ISO
2555
Method Second Edition; Corrected and Reprinted- 1990
Plastics - Determination of the Gas Transmission Rate of Films and Thin Sheets Under Atmospheric Pressure - Manometric Method
ISO
2556
First Edition
Textile Glass Chopped-Strand Mats for Reinforcement of Plastics - Determination of Time of Dissolution of the Binder in Styrene First
ISO
2558
Edition
ISO
2559
Textile Glass - Mats (Made from Chopped or Continuous Strands) - Designation and Basis for Specifications Fourth Edition
Welding Consumables - Covered Electrodes for Manual Metal Arc Welding of Non-Alloy and Fine Grain Steels - Classification
ISO
2560
Second Edition
Plastics Determination of residual styrene monomer in polystyrene (PS) and impact-resistant polystyrene (PS-I) by gas
ISO
2561
chromatography Second Edition
ISO
2562
Modular Units for Machine Tool Construction - Slide Units First Edition; Amendment 1-1982
ISO
2563
Aircraft Ducting and Piping - Profile Dimensions for Flanges of V-Band Couplings First Edition
ISO
2566-1
Steel - Conversion of Elongation Values - Part 1: Carbon and Low Alloy Steels Second Edition
ISO
2566-2
Steel - Conversion of Elongation Values - Part 2: Austenitic Steels First Edition
ISO
2568
Hand- and Machine-Operated Circular Screwing Dies and Hand-Operated Die Stocks Second Edition
ISO
2569
Cork Stoppers - Vocabulary Third Edition
ISO
2572
Textile Machinery and Accessories - Card Gauges Second Edition
ISO
2574
Aircraft - Electrical Cables - Identification Marking Second Edition
ISO
2575 AMD 2
Road vehicles ù Symbols for controls, indicators and tell-tales AMENDMENT 2 Seventh Edition
ISO
2575 AMD 1
Road vehicles ù Symbols for controls, indicators and tell-tales AMENDMENT 1 Seventh Edition
ISO
2575
Road vehicles ù Symbols for controls, indicators and tell-tales Seventh Edition
ISO
2576
Chemical Analysis of Zinc Alloys - Polarographic Determination of Lead and Cadmium in Zinc Alloys Containing Copper First Edition
ISO
2577
Plastics - Thermosetting Moulding Materials - Determination of Shrinkage Second Edition
ISO
2578
Plastics - Determination of Time-Temperature Limits After Prolonged Exposure to Heat Second Edition
Plastics - Acrylonitrile-Butadiene-Styrene (ABS) Moulding and Extrusion Materials - Part 1: Designation System and Basis for
ISO
2580-1
Specifications Fifth Edition
Plastics - Acrylonitrile/ Butadiene/Styrene (ABS) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and
ISO
2580-2
Determination of Properties Third Edition
ISO
2582
Cork and Cork Products - Determination of Thermal Conductivity - Hot Plate Method First Edition
ISO
2584
Cylindrical Cutters with Plain Bore and Key Drive - Metric Series First Edition
ISO
2585
Slotting Cutters with Plain Bore and Key Drive - Metric Series First Edition
ISO
2586
Shell End Mills with Plain Bore and Tenon Drive - Metric Series Second Edition
ISO
2587
Side and Face Milling Cutters with Plain Bore and Key Drive - Metric Series First Edition
ISO
2588
Leather - Sampling - Number of Items for a Gross Sample Second Edition
ISO
2589
Leather Physical and mechanical tests Determination of thickness Second Edition; IULTCS/IUP 4
ISO
2590
General Method for the Determination of Arsenic - Silver Diethyldithiocarbamate Photometric Method First Edition
ISO
2591-1
Test Sieving - Part 1: Methods Using Test Sieves of Woven Wire Cloth and Perforated Metal Plate First Edition
ISO
2592
Determination of Flash and Fire Points - Cleveland Open Cup Method Second Edition
Information Technology - Telecommunications and Information Exchange between Systems - 34-Pole DTE/DCE Interface Connector
ISO
2593
Mateability Dimensions and Contact Number Assignments Fourth Edition
ISO
2594
Building Drawings - Projection Methods First Edition; Erratum-1972
Iron ores Determination of hygroscopic moisture in analytical samples Gravimetric, Karl Fischer and mass-loss methods Fifth
ISO
2596
Edition
ISO
2597-1
Iron ores Determination of total iron content Part 1: Titrimetric method after tin(II) chloride reduction Second Edition
ISO
2598-1
Iron Ores - Determination of Silicon Content - Part 1: Gravimetric Methods First Edition
Iron Ores - Determination of Silicon Content - Part 2: Reduced Molybdosilicate Spectrophotometric Method First Edition; Replaces
ISO
2598-2
ISO 4686
ISO
2599
Iron Ores - Determination of Phosphorus Content - Titrimetric Method Third Edition
ISO
2602
Statistical Interpretation of Test Results - Estimation of the Mean - Confidence Interval Second Edition
ISO
2603
Booths for Simultaneous Interpretation - General Characteristics and Equipment Third Edition
Seamless Steel Tubes for Pressure Purposes - Technical Delivery Conditions - Part 2: Unalloyed and Alloyed Steels with Specified
ISO
9329-2
Elevated Temperature Properties First Edition; Replaces 2604-2 Along with 9329 Parts 1, 3 and 4
Steel Products for Pressure Purposes - Derivation and Verification of Elevated Temperature Properties - Part 3: An Alternative
ISO
2605-3
Procedure for Deriving the Elevated Temperature Yield or Proof Stress Properties When Data Are Limited First Edition
ISO
2624
Copper and Copper Alloys - Estimation of Average Grain Size Second Edition
ISO
2626
Copper - Hydrogen Embrittlement Test First Edition
Mechanical Vibration and Shock - Evaluation of Human Exposure to Whole-Body Vibration - Part 1: General Requirements Second
Edition; Replaces ISO 2631-3:1985; Corrected and Reprinted 07/15/1997; Supersedes NZS ISO 2631.1: 1985 and NZS ISO 2631.3:
ISO
2631-1
1985
Mechanical Vibration and Shock - Evaluation of Human Exposure to Whole-Body Vibration - Part 2: Vibration in Buildings (1 Hz to 80
ISO
2631-2
Hz) Second Edition; Supersedes NZS ISO 2631.2: 1989
Mechanical Vibration and Shock - Evaluation of Human Exposure to Whole-Body Vibration - Part 4: Guidelines for the Evaluation of
ISO
2631-4
the Effects of Vibration and Rotational Motion on Passenger and Crew Comfort in Fixed-Guideway Transport Systems First Edition
Mechanical vibration and shock Evaluation of human exposure to whole-body vibration Part 5: Method for evaluation of vibration
ISO
2631-5
containing multiple shocks First Edition
ISO
2633
Determination of Imposed Floor Loads in Production Buildings and Warehouses First Edition
Aircraft - Conductors for General Purpose Aircraft Electrical Cables and Aerospace Applications - Dimensions and Characteristics
ISO
2635
Second Edition
ISO
2639
Steel - Determination and Verification of the Depth of Carburized and Hardened Cases Third Edition
ISO
2646
Wool - Measurement of the Length of Fibres Processed on the Worsted System, Using a Fibre Diagram Machine First Edition
ISO
2647
Wool - Determination of Percentage of Medullated Fibres by the Projection Microscope First Edition
ISO
2648
Wool - Determination of Fibre Length Distribution Parameters - Electronic Method First Edition
ISO
2669
Environmental Tests for Aircraft Equipment - Steady-State Acceleration Second Edition
ISO
2671
Environmental Tests for Aircraft Equipment - Part 3.4: Acoustic Vibration First Edition
ISO
2678
Environmental Tests for Aircraft Equipment - Insulation Resistance and High Voltage Tests for Electrical Equipment Second Edition
ISO
2685
Aircraft - Environmental Test Procedure for Airborne Equipment - Resistance to Fire in Designated Fire Zones Second Edition
Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material
ISO
2692
requirement (LMR) and reciprocity requirement (RPR) Second Edition
Fibre Building Boards - Hard and Medium Boards for General Purposes - Quality Specifications - Appearance, Shape and
ISO
2695
Dimensional Tolerances First Edition
Fibre Building Boards - Hard and Medium Boards for General Purposes - Quality Specifications - Water Absorption and Swelling in
ISO
2696
Thickness First Edition
ISO
2697
Diesel Engines - Fuel Nozzles - SizeS" Second Edition"
ISO
2698
Diesel Engines - Clamp-Mounted Fuel Injectors, Types 7 and 28 Second Edition
ISO
2699
Diesel Engines - Flange-Mounted Fuel Injectors, SizeS" - Types 2
ISO
2701
Drawn Wire for General Purpose Non-Alloy Steel Wire Ropes - Terms of Acceptance First Edition
ISO
2702
Heat-Treated Steel Tapping Screws - Mechanical Properties Second Edition; CEN EN ISO 2702: 1994; AS/NZS 4412: 1996
ISO
2704
Road Vehicles - M10 x 1 Spark-Plugs with Flat Seating and Their Cylinder Head Housing Fifth Edition
ISO
2705
Road Vehicles - M12 X 1,25 Spark-Plugs with Flat Seating and Their Cylinder Head Housing Sixth Edition
ISO
2709
Information and Documentation - Format for Information Exchange Third Edition
Reciprocating Internal Combustion Engines - Vocabulary - Part 1: Terms for Engine Design and Operation Moteurs Alternatifs A
Combustion Interne-Vocabulaire - Partie 1: Termes Relatifs A La Conception Et Au Fonctionnement Du Moteur First Edition; This
ISO
2710-1
Standard Together with 2710-2 Cancels and Replaces ISO 2710: 1978
Reciprocating Internal Combustion Engines - Vocabulary - Part 2: Terms for Engine Maintenance Moteurs Alternatifs A Combustion
ISO
2710-2
Interne - Vocabulaire - Partie 2: Termes Relatifs A La Maintenance Du Moteur First Edition
Liquid Hydrocarbons - Volumetric Measurement by Displacement Meter Systems Other Than Dispensing Pumps First Edition;
ISO
2714
(Erratum-1982)
ISO
2715
Liquid Hydrocarbons - Volumetric Measurement by Turbine Meter Systems First Edition
ISO
2718
Standard Layout for a Method of Chemical Analysis by Gas Chromatography First Edition
ISO
2719
Determination of Flash Point - Pensky-Martens Closed Cup Method Third Edition
ISO
2720
Photography - General Purpose Photographic Exposure Meters (Photoelectric Type) - Guide to Product Specification First Edition
ISO
2721
Photography - Cameras - Automatic Controls of Exposure First Edition; (ANSI PH3.301-1990)
ISO
2722
Vitreous and Porcelain Enamels - Determination of Resistance to Citric Acid at Room Temperature Second Edition
ISO
2723
Vitreous and Porcelain Enamels for Sheet Steel - Production of Specimens for Testing Second Edition
ISO
2724
Vitreous and Porcelain Enamels for Cast Iron-Production of Specimens for Testing First Edition
ISO
2725-1
Assembly tools for screws and nuts ù Square drive sockets ù Part 1: Hand-operated sockets Second Edition
ISO
2725-2
Assembly tools for screws and nuts ù Square drive sockets ù Part 2: Machine-operated sockets (ôimpactö) Second Edition
Assembly Tools for Screws and Nuts - Square Drive Sockets - Part 3: Machine-Operated Sockets (Non-Impact") - Dimensions First
ISO
2725-3
Edition"
ISO
2726
Woodworking Tools - Metal-Bodied Bench Planes, Plane Cutters and Cap Irons Second Edition
ISO
2727
Modular Units for Machine Tool Construction - Headstocks First Edition; (NZS 5216: 1974)
ISO
2729
Woodworking Tools - Chisels and Gouges Second Edition
ISO
2730
Woodworking Tools - Wooden Bodied Planes First Edition
ISO
2733
Vitreous and Porcelain Enamels - Apparatus for Testing with Acid and Neutral Liquids and Their Vapours Second Edition
ISO
2734
Vitreous and Porcelain Enamels - Apparatus for Testing with Alkaline Liquids Third Edition
Concrete Tests - Test Specimens - Part 2: Making and Curing of Test Specimens for Strength Tests First Edition [Replaced By: ISO
ISO
2736-2
1920-3]
Sintered Metal Materials, Excluding Hardmetals - Permeable Sintered Metal Materials - Determination of Density, Oil Content and
ISO
2738
Open Porosity Third Edition
ISO
2739
Sintered metal bushes Determination of radial crushing strength Second Edition
ISO
2740
Sintered metal materials, excluding hardmetals ù Tensile test pieces Fourth Edition
ISO
2741
Zinc Alloys - Complexometric Determination of Magnesium First Edition
ISO
2742
Vitreous and Porcelain Enamels - Determination of Resistance to Boiling Citric Acid Third Edition
ISO
2743
Vitreous and Porcelain Enamels - Determination of Resistance to Condensing Hydrochloric Acid Vapour Second Edition
ISO
2744
Vitreous and Porcelain Enamels - Determination of Resistance to Boiling Water and Water Vapour Third Edition
ISO
2745
Vitreous and Porcelain Enamels - Determination of Resistance to Hot Sodium Hydroxide Second Edition
Vitreous and Porcelain Enamels - Enamelled Articles for Service under Highly Corrosive Conditions - High Voltage Test Second
ISO
2746
Edition
ISO
2747
Vitreous and Porcelain Enamels - Enamelled Cooking Utensils - Determination of Resistance to Thermal Shock Second Edition
ISO
2748
Textile Machinery and Accessories - Lingoes for Jacquard Weaving Second Edition
ISO
2758
Paper - Determination of Bursting Strength Third Edition
ISO
2759
Board - Determination of Bursting Strength Third Edition
ISO
2762
Hydrochloric Acid for Industrial Use - Determination of Soluble Sulphates - Turbidimetric Method First Edition
General Tolerances - Part 1: Tolerances for Linear and Angular Dimensions without Individual Tolerance Indications First Edition;
ISO
2768-1
(CEN EN 22768-1: 1993)
General Tolerances - Part 2: Geometrical Tolerances for Features without Individual Tolerance Indications First Edition; CEN EN
ISO
2768-2
22768-2: 1993
ISO
2769
Modular Units for Machine Tool Construction - Wing Bases for Slide Units First Edition; (NZS 5217: 1974)
ISO
2772-1
Test Conditions for Box Type Vertical Drilling Machines - Testing of the Accuracy - Part I: Geometrical Tests First Edition
ISO
2772-2
Test Conditions for Box Type Vertical Drilling Machines - Testing of the Accuracy - Part II: Practical Test First Edition
ISO
2773-1
Test Conditions for Pillar Type Vertical Drilling Machines - Testing of the Accuracy - Part I: Geometrical Test First Edition
ISO
2773-2
Test Conditions for Pillar Type Vertical Drilling Machines - Testing of the Accuracy - Part II: Practical Test First Edition
Office Machines and Printing Machines Used for Information Processing - Widths of One-Time Paper or Plastic Printing Ribbons and
ISO
2775
Marking to Indicate the End of the Ribbons Second Edition
ISO
2776
Modular Co-Ordination - Co-Ordinating Sizes for Doorsets - External and Internal First Edition
ISO
2777
Modular Co-Ordination - Co-Ordinating Sizes for Rigid Flat Sheet Boards Used in Building First Edition
ISO
2780
Milling cutters with tenon drive Interchangeability dimensions for cutter arbors Metric series Third Edition
ISO
2781
Rubber, Vulcanized - Determination of Density Third Edition; Technical Corigendum 1:06/01/1996
ISO
2782
Rubber, vulcanized or thermoplastic Determination of permeability to gases Third Edition
ISO
2784
Continuous Forms Used for Information Processing - Sizes and Sprocket Feed Holes First Edition
ISO
2787
Rotary and Percussive Pneumatic Tools - Performance Tests Second Edition
ISO
2788
Documentation - Guidelines for the Establishment and Development of Monolingual Thesauri Second Edition
ISO
2789
Information and documentation International library statistics Fourth Edition
ISO
2790
Belt drives V-belts for the automotive industry and corresponding pulleys Dimensions Fourth Edition
ISO
2795
Plain Bearings - Sintered Bushes - Dimensions and Tolerances Fourth Edition; (NZS/ISO 2795: 1991)
ISO
2796
Cellular Plastics, Rigid - Test for Dimensional Stability Third Edition
ISO
2797
Textile Glass - Rovings - Basis for a Specification Second Edition
ISO
2800
Photography - Expendable Photoflash Lamps - Definition and Evaluation of Flashability First Edition; (Erratum-1980)
ISO
2804
Wire, Bar or Tube Drawing Dies - As-Sintered Pellets of Hardmetal (Carbide) - Dimensions Second Edition
ISO
2806
Industrial Automation Systems - Numerical Control of Machines - Vocabulary Second Edition
ISO
2808
Paints and Varnishes - Determination of Film Thickness Fourth Edition
ISO
2810
Paints and varnishes Natural weathering of coatings Exposure and assessment Second Edition
Paints and Varnishes - Determination of Density - Part 1: Pyknometer Method First Edition; Replaces ISO 2811 Supercedes ISO
ISO
2811-1
8962
ISO
2811-2
Paints and Varnishes - Determination of Density - Part 2: Immersed Body (Plummet) Method First Edition; Replaces ISO 2811
ISO
2811-3
Paints and Varnishes - Determination of Density - Part 3: Oscillation Method First Edition; Replaces ISO 2811 Supercedes ISO 8962
ISO
2811-4
Paints and Varnishes - Determination of Density - Part 4: Pressure Cup Method First Edition; Replaces ISO 2811
ISO
2812-1
Paints and varnishes ù Determination of resistance to liquids ù Part 1: Immersion in liquids other than water Second Edition
ISO
2812-2
Paints and varnishes ù Determination of resistance to liquids ù Part 2: Water immersion method Second Edition
ISO
2812-3
Paints and varnishes ù Determination of resistance to liquids ù Part 3: Method using an absorbent medium First Edition
ISO
2812-4
Paints and varnishes ù Determination of resistance to liquids ù Part 4: Spotting methods First Edition
ISO
2812-5
Paints and varnishes ù Determination of resistance to liquids ù Part 5: Temperature-gradient oven method First Edition
Paints and Varnishes - Determination of Specular Gloss of Non-Metallic Paint Films at 20 Degrees, 60 Degrees and 85 Degrees
ISO
2813
Third Edition; AS/NZS 1580.602.2:1995; Corrigendum 1 02/15/1997
ISO
2814
Paints and Varnishes - Comparison of Contrast Ratio (Hiding Power) of Paints of the Same Type and Colour First Edition
ISO
2815
Paints and Varnishes - Buchholz Indentation Test Second Edition
ISO
2817
Tobacco and Tobacco Products - Determination of Silicated Residues Insoluble in Hydrochloric Acid Second Edition
ISO
2818
Plastics - Preparation of Test Specimens by Machining Third Edition
Metallic Coatings on Metallic Substrates - Electrodeposited and Chemically Deposited Coatings - Review of Methods Available for
ISO
2819
Testing Adhesion Second Edition; (CEN EN ISO 2819: 1994) (PNS 686: 1990)
ISO
2820
Leather - Raw Hides of Cattle and Horses - Method of Trim First Edition; PNS 960:1986; Amendment 1 - 1996
ISO
2821
Leather - Raw Hides of Cattle and Horses - Preservation by Stack Salting First Edition; PNS 961: 1986; Amendment 1 - 1996
ISO
2822-1
Raw Cattle Hides and Calf Skins - Part 1: Descriptions of Defects First Edition
ISO
2825
Spices and Condiments - Preparation of a Ground Sample for Analysis Second Edition
ISO
2826
Apricots - Guide to Cold Storage First Edition
ISO
2827
Photography - Electronic Flash Equipment - Determination of Light Output and Performance Second Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Fluorine Content - Alizarin Complexone and
ISO
2828
Lanthanum Chloride Spectrophotometric Method First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Phosphorus Content - Reduced
ISO
2829
Phosphomolybdate Spectrophotometric Method First Edition
ISO
2830
Cryolite, Natural and Artificial - Determination of Aluminium Content - Atomic Absorption Method First Edition
ISO
2831
Sodium Fluoride for Industrial Use - Determination of Water-Insoluble Matter First Edition
ISO
2832
Sodium Fluoride for Industrial Use - Determination of Moisture Content First Edition
ISO
2833
Sodium Fluoride for Industrial Use - Determination of Fluorine Content - Modified Willard-Winter Method First Edition
Graphic technology Laboratory preparation of test prints Part 1: Paste inks First Edition; Together with ISO 2834-2 and ISO 2834-3
ISO
2834-1
Replaces ISO 2834:1999
ISO
2835
Prints and Printing Inks - Assessment of Light Fastness First Edition
Graphic technology Prints and printing inks Assessment of resistance to various agents Third Edition; Cancels and Replaces ISO
ISO
2836
2837:1996; ISO 11628:1995
Graphic technology Colour and transparency of printing ink sets for fourcolour printing Part 1: Sheet-fed and heat-set web offset
ISO
2846-1
lithographic printing Second Edition
Graphic Technology - Colour and Transparency of Ink Sets for Four-Colour-Printing - Part 2: Coldset offset Lithographic Printing First
ISO
2846-2
Edition
Graphic Technology - Colour and Transparency of Printing Ink Sets for Four-Colour-Printing - Part 3: Publication Gravure Printing
ISO
2846-3
First Edition
ISO
2846-4
Graphic Technology - Colour and Transparency of Ink Sets for Four-Colour-Printing - Part 4: Screen Printing First Edition
ISO
2846-5
Graphic technology Colour and transparency of printing ink sets for four-colour printing Part 5: Flexographic printing First Edition
ISO
2848
Building Construction - Modular Coordination - Principles and Rules Second Edition; (PNS 638: 1988)
ISO
2851
Stainless Steel Bends and Tees for the Food Industry Second Edition
ISO
2852
Stainless Steel Clamp Pipe Couplings for the Food Industry Second Edition
ISO
2853
Stainless Steel Threaded Couplings for the Food Industry Second Edition
ISO
2854
Statistical Interpretation of Data - Techniques of Estimation and Tests Relating to Means and Variances First Edition
ISO
2855
Radioactive Materials - Packagings - Tests for Contents Leakage and Radiation Leakage First Edition; (Amendment Slip-1976)
Ground Thread Taps for ISO Metric Threads of Tolerances 4H to 8H and 4G to 6G Coarse and Fine Pitches - Manufacturing
ISO
2857
Tolerances on the Threaded Portion First Edition; (Amendment 1-1984) (Amendment 2-1986) (Corrigendum 1-1990)
End-Suction Centrifugal Pumps (Rating 16 Bar) - Designation, Nominal Duty Point and Dimensions Second Edition; (CEN EN 22858:
ISO
2858
1993)
Sampling Procedures for Inspection by Attributes - Part 1: Sampling Schemes Indexed by Acceptance Quality Limit (AQL) for Lot-by-
ISO
2859-1
Lot Inspection Second Edition; Corrigendum 1: 03-01-2001
Sampling Procedures for Inspection by Attributes - Part 2: Sampling Plans Indexed by Limiting Quality (LQ) for Isolated Lot Inspection
ISO
2859-2
First Edition
ISO
2859-3
Sampling procedures for inspection by attributes - Part 3: Skip-lot sampling procedures Second edition
ISO
2859-4
Sampling Procedures for Inspection by Attributes - Part 4: Procedures for Assessment of Declared Quality Levels Second Edition
Sampling procedures for inspection by attributes - Part 5: System of sequential sampling plans indexed by acceptance quality limit
ISO
2859-5
(AQL) for lot-by-lot inspection First Edition
Sampling procedures for inspection by attributes Part 10: Introduction to the ISO 2859 series of standards for sampling for inspection
ISO
2859-10
by attributes First Edition; Supersedes ISO 2859-0:1995
ISO
2860
Earth-Moving Machinery - Minimum Access Dimensions Fourth Edition
ISO
2861-1
Vacuum Technology - Quick-Release Couplings - Dimensions - Part I: Clamped Type First Edition
ISO
2861-2
Vacuum Technology - Quick Release Couplings - Dimensions - Part 2: Screwed Type First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Boron Content - Curcumin Spectrophotometric
ISO
2865
Method First Edition; Corrigendum 1: 1991
ISO
2867
Earth-Moving Machinery - Access Systems Sixth Edition
ISO
2868
Surface Active Agents - Detergents - Anionic-Active Matter Stable to Acid Hydrolysis - Determination of Trace Amounts First Edition
Surface Active Agents - Detergents - Anionic-Active Matter Hydrolyzable Under Alkaline Conditions - Determination of Hydrolyzable
ISO
2869
and Non-Hydrolyzable Anionic-Active Matter First Edition
Surface Active Agents - Detergents - Determination of Anionic-Active Matter Hydrolyzable and Non-Hydrolyzable Under Acid-
ISO
2870
Conditions Second Edition
Surface Active Agents - Detergents - Determination of Cationic-Active Matter Content - Part 1: High-Molecular-Mass Cationic-Active
ISO
2871-1
Matter First Edition
Surface Active Agents - Detergents - Determination of Cationic-Active Matter Content - Part 2: Cationic-Active Matter of Low
ISO
2871-2
Molecular Mass (Between 200 and 500) First Edition Corrected and Reprinted 12/15/1991
ISO
2873
Packaging - Complete, Filled Transport Packages and Unit Loads - Low Pressure Test Third Edition
ISO
2875
Packaging - Complete, Filled Transport Packages and Unit Loads - Water-Spray Test Third Edition
ISO
2876
Packaging - Complete, Filled Transport Packages - Rolling Test Second Edition; (CEN EN 22876: 1992)
ISO
2878
Rubber - Antistatic and conductive products - Determination of electrical resistance Third Edition
ISO
2881
Tobacco and Tobacco Products - Determination of Alkaloid Content - Spectrophotometric Method Third Edition
Paints and Varnishes - Determination of Viscosity Using Rotary Viscometers - Part 1: Cone-and-Plate Viscometer Operated at a High
ISO
2884-1
Rate of Shear First Edition; Superseded by BS 3900-A7-1: 2000
Paints and Varnishes - Determination of Viscosity Using Rotary Viscometers - Part 2: Disc or Ball Viscometer Operated at a Specified
ISO
2884-2
Speed First Edition
ISO
2889
General Principles for Sampling Airborne Radioactive Materials First Edition
ISO
2891
Modular Units for Machine Tool Construction - Centre Bases and Columns Second Edition
ISO
2892
Austenitic cast irons - Classification Second edition
ISO
2896
Rigid Cellular Plastics - Determination of Water Absorption Third Edition
Plastics - Impact-Resistant Polystyrene (PS-I) Moulding and Extrusion Materials - Part 1: Designation System and Basis for
ISO
2897-1
Specifications Second Edition
Plastics Impact-resistant polystyrene (PS-I) moulding and extrusion materials Part 2: Preparation of test specimens and
ISO
2897-2
determination of properties Third Edition
Plastics - Plasticized Poly(Vinyl Chloride) (PVC-P) Moulding and Extrusion Materials - Part 1: Designation System and Basis for
ISO
2898-1
Specifications Third Edition
Plastics - Plasticized Poly(Vinyl Chloride) (PVC-P) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and
ISO
2898-2
Determination of Properties Third Edition
ISO
2901
ISO Metric Trapezoidal Screw Threads - Basic Profile and Maximum Material Profiles Second Edition
ISO
2902
ISO Metric Trapezoidal Screw Threads - General Plan First Edition
ISO
2903
ISO Metric Trapezoidal Screw Threads - Tolerances Second Edition
ISO
2904
ISO Metric Trapezoidal Screw Threads - Basic Dimensions First Edition
ISO
2905
Modular Units for Machine Tool Construction - Spindle Noses and Adjustable Adaptors for Multi-Spindle Heads Second Edition
ISO
2906
Cinematography - Image Area Produced by Camera Aperture on 35 mm Motion-Picture Film - Position and Dimensions Third Edition
ISO
2907
Cinematography - Maximum Projectable Image Area on 35 mm Motion-Picture Film - Position and Dimensions Third Edition
ISO
2908
Petroleum Waxes - Determination of Oil Content First Edition
ISO
2909
Petroleum products - Calculation of viscosity index from kinematic viscosity Third Edition
ISO
2910
Cinematography ù Screen luminance and chrominance for the projection of motion pictures Third edition
ISO
2911
Sweetened Condensed Milk - Determination of Sucrose Content - Polarimetric Method Second Edition
Modular Units for Machine Tool Construction - Multi-Spindle Heads - Casing and Input Drive Shaft Dimensions First Edition;
ISO
2912
Amendment 1: 1982
ISO
2913
Wool - Colorimetric Determination of Cystine Plus Cysteine in Hydrolysates First Edition
ISO
2915
Wool - Determination of Cysteic Acid Content of Wool Hydrolysates by Paper Electrophoresis and Colorimetry First Edition
ISO
2916
Wool - Determination of Alkali Content First Edition
ISO
2917
Meat and Meat Products - Measurement of pH - Reference Method Second Edition
ISO
2918
Meat and Meat Products - Determination of Nitrite Content (Reference Method) First Edition; (PNS 608: 1992)
Radioactive Protection - Sealed Radioactive Sources - General Requirements and Classification Second Edition; Cancels and
ISO
2919
Replaces ISO 1677: 1977
ISO
2920
Whey Cheese - Determination of Dry Matter Content (Reference Method) Second Edition: IDF 58
Rubber, Vulcanized - Determination of Low-Temperature Characteristics - Temperature-Retraction Procedure (TR Test) Fourth
ISO
2921
edition
ISO
2922
Acoustics - Measurement of Airborne Sound Emitted by Vessels on Inland Waterways and Harbours Second Edition
ISO
2923
Acoustics - Measurement of Noise on Board Vessels Second Edition; Technical Corrigendum 1-1997
Solid and Segmental Circular Saws for Cold Cutting of Metals - Interchangeability Dimensions of the Drive - Saw Diameter Range
ISO
2924
224 to 2 240 mm First Edition
Aluminium oxide used for the production of primary aluminium Particle size analysis for the range 45 Ám to 150 Ám Method using
ISO
2926
electroformed sieves Second Edition
ISO
2927
Aluminium Oxide Primarily Used for the Production of Aluminium - Sampling First Edition
Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar
ISO
2928
(2,5 MPa) Specification Third Edition
ISO
2929
Rubber Hoses and Hose Assemblies for Bulk Fuel Delivery by Truck - Specification Third Edition
ISO
2930
Rubber, Raw Natural - Determination of Plasticity Retention Index (PRI) Third Edition
Anodizing of Aluminium and Its Alloys - Assessment of Quality of Sealed Anodic Oxide Coatings by Measurement of Admittance or
ISO
2931
Impedance Second Edition
ISO
2934
Modular Units for Machine Tool Construction - Wing Base for Columns First Edition; (NZS 5220: 1974)
ISO
2935
Circular Saw Blades for Woodworking - Dimensions First Edition
ISO
2936
Assembly Tools for Screws and Nuts - Hexagon Socket Screw Keys Fifth Edition
ISO
2937
Plain End Seamless Steel Tubes for Mechanical Application First Edition
ISO
2938
Hollow Steel Bars for Machining First Edition; (Erratum-1979)
ISO
2939
Cinematography - Picture Image Area on 35 mm Motion-Picture Release Prints - Position and Dimensions Third Edition
ISO
2940-1
Milling Cutters Mounted on Centring Arbors Having a 7/24 Taper - Fitting Dimensions - Centring Arbors First Edition; (Erratum-1977)
ISO
2940-2
Milling Cutters Mounted on Centring Arbors Having a 7/24 Taper - Inserted Tooth Cutters First Edition; (Erratum-1977)
ISO
2941
Hydraulic Fluid Power - Filter Elements - Verification of Collapse/Burst Resistance First Edition
Hydraulic Fluid Power - Filter Elements - Verification of Fabrication Integrity and Determination of the First Bubble Point Fourth
ISO
2942
Edition
ISO
2943
Hydraulic Fluid Power - Filter Elements - Verification of Material Compatibility with Fluids Second Edition
ISO
2944
Fluid Power Systems and Components - Nominal Pressures Second Edition
ISO
2947
Textiles - Integrated Conversion Table for Replacing Traditional Yarn Numbers by Rounded Values in the Tex System First Edition
ISO
2950
Brown Coals and Lignites - Classification by Types on the Basis of Total Moisture Content and Tar Yield First Edition
ISO
2951
Vulcanized Rubber - Determination of Insulation Resistance First Edition
ISO
2953
Machanical Vibration - Balancing Machines - Description and Evaluation Third Edition
Mechanical Vibration of Rotating and Reciprocating Machinery - Requirements for Instruments for Measuring Vibration Severity First
ISO
2954
Edition
ISO
2958
Road Vehicles - Exterior Protection for Passenger Cars First Edition
ISO
2959
Textiles - Woven Fabric Descriptions First Edition
ISO
2961
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of an Adsorption Index First Edition
Cheese and Processed Cheese Products - Determination of Total Phosphorus Content - Molecular Absorption Spectrometric Method
ISO
2962
Second Edition
ISO
2964
Aerospace - Tubing - Outside Diameters and Thicknesses - Metric Dimensions Second Edition
Material Used as Cigarette Papers, Filter Plug Wrap and Filter Joining Paper, Including Materials having an Oriented Permeable
ISO
2965
Zone - Determination of Air Permeability Second Edition
Cinematography - B-Chain Electro-Acoustic Response of Motion-Picture Control Rooms and Indoor Theatres - Specifications and
ISO
2969
Measurements Second Edition
ISO
2971
Cigarettes and Filter Rods - Determination of Nominal Diameter - Method Using a Laser Beam Measuring Apparatus Third Edition
ISO
2972
Numerical Control of Machines - Symbols Second Edition
ISO
2974
Diesel engines - High-pressure fuel injection pipe end-connections with 60 Degree female cone Sixth Edition
ISO
2975-1
Measurement of Water FLow in Closed Conduits - Tracer Methods - Part I: General First Edition
Measurement of Water Flow in Closed Conduits - Tracer Methods - Part II: Constant Rate Injection Method Using Non-Radioactive
ISO
2975-2
Tracers First Edition
Measurement of Water Flow in Closed Conduits - Tracer Methods - Part III: Constant Rate Injection Method Using Radioactive
ISO
2975-3
Tracers First Edition
Measurement of Water Flow in Closed Conduits - Tracer Methods - Part VI: Transit Time Method Using Non-Radioactive Tracers
ISO
2975-6
First Edition
Measurement of Water Flow in Closed Conduits - Tracer Methods - Part VII: Transit Time Method Using Radioactive Tracers First
ISO
2975-7
Edition
ISO
2976
Coated abrasives Abrasive belts Selection of width/length combinations Second Edition
ISO
2977
Petroleum Products and Hydrocarbon Solvents - Determination of Aniline Point and Mixed Aniline Point Third Edition
ISO
2982-1
Rolling Bearings - Accessories - Part 1: Tapered Sleeves - Dimensions First Edition; Replaces ISO 113-1: 1979
ISO
2982-2
Rolling Bearings - Accessories - Part 2: Locknuts and Locking Devices - Dimensions Second Edition
ISO
2992
Ammonium Sulphate for Industrial Use - Determination of Iron Content - 2,2'-Bipyridyl Photometric Method First Edition
ISO
2993
Ammonium Sulphate for Industrial Use - Determination of Free Acidity - Titrimetric Method First Edition
ISO
2997
Phosphoric Acid for Industrial Use - Determination of Sulphate Content - Method by Reduction and Titrimetry First Edition
ISO
3001
Plastics - Epoxy Compounds - Determination of Epoxy Equivalent Fourth Edition
Basic Quantities in Cutting and Grinding - Part 1: Geometry of the Active Part of Cutting Tools - General Terms, Reference Systems,
ISO
3002-1
Tool and Working Angles, Chip Breakers Second Edition; (Amendment 1-1992)
Basic Quantities in Cutting and Grinding - Part 2: Geometry of the Active Part of Cutting Tools - General Conversion Formulae to
ISO
3002-2
Relate Tool and Working Angles First Edition
ISO
3002-3
Basic Quantities in Cutting and Grinding - Part 3: Geometric and Kinematic Quantities in Cutting First Edition
ISO
3002-4
Basic Quantities in Cutting and Grinding - Part 4: Forces, Energy, Power First Edition
ISO
3002-5
Basic Quantities in Cutting and Grinding - Part 5: Basic Terminology for Grinding Processes Using Grinding Wheels First Edition
ISO
3005
Textiles - Determination of Dimensional Change of Fabrics Induced by Free-Steam Second Edition
ISO
3006
Road vehicles Passenger car wheels for road use Test methods Fourth edition
ISO
3007
Petroleum Products and Crude Petroleum - Determination of Vapour Pressure - Reid Method Third Edition
ISO
3008
Fire-resistance tests ù Door and shutter assemblies Third edition
ISO
3009
Fire-resistance tests Elements of building construction Glazed elements Second Edition
ISO
3010
Basis for design of structures Seismic actions on structures Second Edition
ISO
3011
Rubber- or Plastics-Coated Fabrics - Determination of Resistance to Ozone Cracking Under Static Conditions Third Edition
Petroleum Products - Determination of Thiol (Mercaptan) Sulfur in Light and Middle Distillate Fuels - Potentiometric Method Third
ISO
3012
Edition
ISO
3013
Petroleum Products - Determination of the Freezing Point of Aviation Fuels First Edition
ISO
3014
Petroleum Products - Determination of the Smoke Point of Kerosine Third Edition
ISO
3015
Petroleum Products - Determination of Cloud Point Second Edition; (CEN EN 23015: 1994)
ISO
3016
Petroleum Products - Determination of Pour Point Second Edition; Corrected and Reprinted - 1995
ISO
3018
Rectangular Textile Floor Coverings - Determination of Dimensions First Edition (AS/NZS 2111.20: 1996)
Hydraulic Fluid Power - Dimensions and Identification Code for Mounting Flanges and Shaft Ends of Displacement Pumps and
ISO
3019-1
Motors - Part 1: Inch Series Shown in Metric Units Second Edition; Supersedes ISO 3019/1
Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors
ISO
3019-2
Part 2: Metric series Third Edition; Technical Corrigendum 1: 12/01/2006;:1988 [Replaced: ISO 3019-3]
ISO
3022
Cinematography - 35 mm Motion-Picture Film Perforated 16 mm (1-3-0) - Cutting and Perforating Dimensions Third Edition
ISO
3023
Cinematography - 65 mm and 70 mm Unexposed Motion-Picture Film - Cutting and Perforating Dimensions Fourth Edition
Cinematography - Motion-Picture Camera Cartridge, 8 mm Type S, Model I - Camera Run Length, Perforation Cut-Out and End-of-
ISO
3024
Run Notch in Film - Specifications Second Edition
Cinematography - Printed 8 mm Type S Image Area on 35 mm Motion-Picture Film Perforated 8 mm Type S, 2R-4.227 (1664) or 5R-
ISO
3026
4.234 (1667) - Position and Dimensions Second Edition
ISO
3028
Photography - Camera Flash Illuminants - Determination of ISO Spectral Distribution Index (ISO/SDI) Second Edition
ISO
3030
Roller Bearings - Radial Needle Roller and Cage Assemblies - Dimensions and Tolerances Second Edition
ISO
3031
Roller Bearings - Thrust Needle Roller and Cage Assemblies, Thrust Washers - Boundary Dimensions and Tolerances Third Edition
ISO
3033-1
Oil of spearmint Part 1: Native type (Mentha spicata L.) First Edition; Supersedes ISO 3033:1998
Oil of spearmint Part 2: Chinese type (80 % and 60 %) (Mentha viridis L. var. crispa Benth.), redistilled oil First Edition; Supersedes
ISO
3033-2
ISO 3033:1998
ISO
3033-3
Oil of spearmint Part 3: Indian type (Mentha spicata L.), redistilled oil First Edition; Supersedes ISO 3033:1998
ISO
3033-4
Oil of spearmint Part 4: Scotch variety (Mentha Î gracilis Sole) First Edition; Supersedes ISO 3033:1998
ISO
3034
Corrugated Fibreboard - Determination of Thickness First Edition
ISO
3035
Single-Faced and Single-Wall Corrugated Fibreboard - Determination of Flat Crush Resistance Second Edition
ISO
3036
Board - Determination of Puncture Resistance First Edition
ISO
3037
Corrugated fibreboard ù Determination of edgewise crush resistance (unwaxed edge method) Fourth Edition
ISO
3038
Corrugated Fibreboard - Determination of the Water Resistance of the Glue Bond by Immersion First Edition
ISO
3039
Corrugated Fibreboard - Determination of the Grammage of the Component Papers After Separation First Edition
ISO
3040
Technical Drawings - Dimensioning and Tolerancing - Cones Second Edition
Cinematography - Labelling of Containers for Raw-Stock Motion-Picture Films and Magnetic Films - Minimum Information
ISO
3042
Specifications Third Edition; Corrigendum 1:2/1/2004
ISO
3043
Oil of Pimento Berry First Edition
ISO
3044
Oil of Eucalyptus Citriodora Hook. Second Edition
ISO
3045
Oil of bay [Pimenta racemosa (Mill.) J.W. Moore] Second Edition
Reciprocating Internal Combustion Engines - Performance - Part 1: Declarations of Power, Fuel and Lubricating Oil Consumptions,
ISO
3046-1
and Test Methods - Additional Requirements for Engines for General Use Fifth Edition
ISO
3046-3
Reciprocating Internal Combustion Engines - Performance - Part 3: Test Measurements Third Edition
ISO
3046-4
Reciprocating Internal Combustion Engines - Part 4: Speed Governing Second Edition
ISO
3046-5
Reciprocating Internal Combustion Engines - Performance - Part 5: Torsional Vibrations Second Edition
Reciprocating Internal Combustion Engines - Performance - Part 6: Overspeed Protection Third Edition; Corrected and Reprinted
ISO
3046-6
12/15/1991
Cinematography - Spool, Daylight Loading Type, for 35 mm Motion-Picture Cameras (Capacity 30 m - 100 ft) - Dimensions Second
ISO
3047
Edition
ISO
3048
Gypsum Plasters - General Test Conditions First Edition
ISO
3049
Gypsum Plasters - Determination of Physical Properties of Powder First Edition
ISO
3051
Gypsum Plasters - Determination of Mechanical Properties First Edition
ISO
3052
Gypsum Plasters - Determination of Water of Crystallization Content First Edition
ISO
3053
Oil of grapefruit (Citrus Î paradisi Macfad.), obtained by expression Second Edition
ISO
3054
Oil of Lavandin Abrial (Lavandula Angustifolia Miller X Lavandula Latifolia Medikus), French Type Third Edition
ISO
3055
Kitchen Equipment - Coordinating Sizes Second Edition
ISO
3056
Non-Calibrated Round Steel Link Lifting Chain and Chain Slings - Use and Maintenance Second Edition
ISO
3057
Non-Destructive Testing - Metallographic Replica Techniques of Surface Examination Second Edition
ISO
3058
Non-Destructive Testing - Aids to Visual Inspection - Selection of Low-Power Magnifiers Second Edition
Non-Destructive Testing - Penetrant Testing and Magnetic Particle Testing - Viewing Conditions Second Edition; Corrected and
ISO
3059
Reprinted: 01/15/2002
ISO
3060
Cotton Fibres - Determination of Breaking Tenacity of Flat Bundles First Edition
ISO
3061
Oil of Black Pepper First Edition
ISO
3063
Oil of ylang-ylang [Cananga odorata (Lam.) Hook. f. et Thomson forma genuina] Second Edition
Oil of Petitgrain, Paraguayan Type (Citrus Aurantium L. ssp. Aurantium, syn. Citrus Aurantium L. ssp. Amara var. Pumilia) Second
ISO
3064
Edition
ISO
3065
Oil of Australian Eucalyptus, 80 to 85 % Cineole Content First Edition
ISO
3066
Duplicating Machines - Registration Second Edition
ISO
3069
End-Suction Centrifugal Pumps - Dimensions of Cavities for Mechanical Seals and for Soft Packing Second Edition
Acceptance Conditions for Boring and Milling Machines with Horizontal Spindle - Testing of the Accuracy - Part 0: General
ISO
3070-0
Introduction Second Edition
ISO
3070-2
Test Conditions for Boring and Milling Machines with Horizontal Spindle - Part 2: Table-Type Machines Third Edition
Test Conditions for Boring and Milling Machines with Horizontal Spindle - Testing of the Accuracy - Part 3: Floor Type Machines with
ISO
3070-3
Detached,Stationary Work-Holding Table Second Edition
Test Conditions for Boring and Milling Machines with Horizontal Spindle - Testing of the Accuracy - Part 4: Planer Type Machines with
ISO
3070-4
Movable Column Second Edition
ISO
3071
Textiles - Determination of pH of the Aqueous Extract Third Edition
ISO
3072
Wool - Determination of Solubility in Alkali First Edition
ISO
3073
Wool - Determination of Acid Content First Edition
ISO
3074
Wool - Determination of Dichloromethane-Soluble Matter in Combed Sliver First Edition
ISO
3075
Short Link Chain for Lifting Purposes - Grade S (6), Non-Calibrated, for Chain Slings, Etc. First Edition; (NZS/ISO 3075: 1980)
ISO
3076
Short Link Chain for Lifting Purposes - Grade T (8), Non-Calibrated, for Chain Slings, Etc. Second Edition; (NZS/ISO 3076: 1984)
ISO
3077
Short Link Chain for Lifting Purposes - Grade T, (Types T, DAT and DT), Fine Tolerance Hoist Chain Third Edition
ISO
3078
Shipbuilding - Cargo Winches Second Edition
ISO
3082
Iron Ores - Sampling and Sample Preparation Procedures Third Edition
ISO
3084
Iron Ores - Experimental Methods for Evaluation of Quality Variation Third Edition
ISO
3085
Iron Ores - Experimental Methods for Checking the Precision of Sampling, Sample Preparation and Measurement Fourth Edition
ISO
3086
Iron ores Experimental methods for checking the bias of sampling Fourth Edition
ISO
3087
Iron Ores - Determination of the Moisture Content of a Lot Third Edition
ISO
3089
Machine tools Test conditions for self-centring, manually-operated chucks with one-piece jaws Third Edition
ISO
3091
Meat and Meat Products - Determination of Nitrate Content (Reference Method) First Edition
Wheat, rye and respective flours, durum wheat and durum wheat semolina Determination of the Falling Number according to
ISO
3093
Hagberg-Perten Third Edition
ISO
3095
Railway applications Acoustics Measurement of noise emitted by railbound vehicles Second Edition
Rolling Bearings - Needle Rollers - Dimensions and Tolerances Second Edition; Corrigendum 1 07/15/1999; Replaces ISO 6193;
ISO
3096
1980
ISO
3098-0
Technical Product Documentation - Lettering - Part 0: General Requirements First Edition
ISO
3098-2
Technical Product Documentation - Lettering - Part 2: Latin Alphabet, Numerals and Marks Second Edition
ISO
3098-3
Technical Product Documentation - Lettering - Part 3: Greek Alphabet Second Edition
ISO
3098-4
Technical Product Documentation - Lettering - Part 4: Diacritical and Particular Marks for the Latin Alphabet Second Edition
ISO
3098-5
Technical Product Documentation - Lettering - Part 5: CAD Lettering of the Latin Alphabet, Numerals and Marks First Edition
ISO
3098-6
Technical Product Documentation - - Lettering - Part 6: Cyrillic Alphabet First Edition
ISO
3103
Tea - Preparation of Liquor for Use in Sensory Tests First Edition
Petroleum Products - Transparent and Opaque Liquids - Determination of Kinematic Viscosity and Calculation of Dynamic Viscosity
ISO
3104
Second Edition; Corrigendum 1-1997;
ISO
3105
Glass Capillary Kinematic Viscometers - Specifications and Operating Instructions Second Edition
ISO
3107 CORR 1
Dentistry ù Zinc oxide/eugenol and zinc oxide/non-eugenol cements TECHNICAL CORRIGENDUM 1 Third Edition
ISO
3107
Dentistry ù Zinc oxide/eugenol and zinc oxide/non-eugenol cements Third Edition
ISO
3108
Steel Wire Ropes for General Purposes - Determination of Actual Breaking Load First Edition
ISO
3110
Copper Alloys - Determination of Aluminium as Alloying Element - Volumetric Method First Edition
ISO
3111
Copper Alloys - Determination of Tin as Alloying Element - Volumetric Method First Edition
ISO
3112
Copper and Copper Alloys - Determination of Lead - Extracting Titration Method First Edition
ISO
3114
Unplasticized Polyvinyl Chloride (PVC) Pipes for Potable Water Supply - Extractability of Lead and Tin - Test Method First Edition
ISO
3116
Magnesium and magnesium alloys ù Wrought magnesium alloys Fourth edition
ISO
3117
Tangential Keys and Keyways First Edition
ISO
3126
Plastics piping systems Plastics components Determination of dimensions Second edition
ISO
3127
Thermoplastics Pipes - Determination of Resistance to External Blows - Round-the-Clock Method Second Edition
ISO
3129
Wood - Sampling Methods and General Requirements for Physical and Mechanical Tests First Edition; (PNS 968: 1989)
ISO
3130
Wood - Determination of Moisture Content for Physical and Mechanical Tests First Edition
ISO
3131
Wood - Determination of Density for Physical and Mechanical Tests First Edition
ISO
3132
Wood - Testing in Compression Perpendicular to Grain First Edition; (PNS 969: 1989)
ISO
3133
Wood - Determination of Ultimate Strength in Static Bending First Edition
ISO
3134-1
Light Metals and Their Alloys - Terms and Definitions - Part 1: Materials First Edition; (Corrected and Reprinted - 1989)
ISO
3134-2
Light Metals and Their Alloys - Terms and Definitions - Part 2: Unwrought Products First Edition; (Corrected and Reprinted - 1989)
ISO
3134-3
Light Metals and Their Alloys - Terms and Definitions - Part 3: Wrought Products First Edition; (Corrected and Reprinted - 1989)
ISO
3134-4
Light Metals and Their Alloys - Terms and Definitions - Part 4: Castings First Edition; (Corrected and Reprinted - 1989)
ISO
3134-5
Light Metals and Their Alloys - Terms and Definitions - Part 5: Methods of Processing and Treatment First Edition
ISO
3136
Rubber Latex - Styrene-Butadiene - Determination of Bound Styrene Content Second Edition
ISO
3137
Anhydrous Hydrogen Fluoride for Industrial Use - Sampling First Edition
ISO
3139
Aqueous Hydrofluoric Acid for Industrial Use - Sampling and Methods of Test Second Edition; Amendment 1: 1980
ISO
3140
Oil of sweet orange [Citrus sinensis (L.) Osbeck], obtained by mechanical treatment Third Edition
Oil of Clove Leaf [Syzygium Aromaticum (L.) Merr. Et Perry, Syn. Eugenia Caryophyllus (Sprengel) Bullock Et S. Harrison] Third
ISO
3141
Edition
Oil of Clove Buds [Syzygium Aromaticum (L.) Merr. Et Perry, Syn. Eugenia Caryophyllus (Sprengel) Bullock Et S. Harrison] Second
ISO
3142
Edition
Oil of Clove Stems [Syzygium Aromaticum (L.) Merr. Et Perry, Syn. Eugenia Caryophyllus (Sprengel) Bullock Et S. Harrison] Second
ISO
3143
Edition
Plastics - Determination of Melting Behaviour (Melting Temperature or Melting Range) of Semi-Crystalline Polymers by Capillary
ISO
3146
Tube and Polarizing-Microscope Methods Third Edition; Technical Corrigendum 1: 10/15/2002
ISO
3150
Radiators, Convectors and Similar Appliances - Calculation of Thermal Output and Presentation of Results First Edition
ISO
3154
Stranded Wire Ropes for Mine Hoisting - Technical Delivery Requirements Second Edition
ISO
3155
Stranded Wire Ropes for Mine Hoisting - Fibre Components - Characteristics and Tests First Edition
Stranded Wire Ropes for Mine Hoisting - Impregnating Compounds, Lubricants and Service Dressings - Characteristics and Tests
ISO
3156
First Edition
ISO
3157
Radioluminescence for Time Measurement Instruments - Specifications Second Edition
ISO
3158
Timekeeping Instruments - Symbolization of Control Positions First Edition
ISO
3159
Timekeeping Instruments - Wrist-Chronometers with Spring Balance Oscillator First Edition
ISO
3160-1
Watch-Cases and Accessories - Gold Alloy Coverings - Part 1: General Requirements Third Edition; Amendment 1: 02-15-2000
Watch-cases and accessories Gold alloy coverings Part 2: Determination of fineness, thickness, corrosion resistance and adhesion
ISO
3160-2
Third Edition
Watch Cases and Accessories - Gold Alloy Coverings - Part 3: Abrasion Resistance Tests of a Type of Coating on Standard Gauges
ISO
3160-3
First Edition
ISO
3161
Aerospace - UNJ Threads - General Requirements and Limit Dimensions Third Edition
ISO
3164
Earth-Moving Machinery - Laboratory Evaluations of Protective Structures - Specifications for Deflection-Limiting Volume Fifth Edition
ISO
3165
Sampling of Chemical Products for Industrial Use - Safety in Sampling First Edition
Codes for the representation of names of countries and their subdivisions ù Part 1: Country codes Codes pour la reprÚsentation des
ISO
3166-1 CORR 1
noms de pays et de leurs subdivisions ù Partie 1: Codes de pays First Edition
Codes for the representation of names of countries and their subdivisions Part 1: Country codes Codes pour la reprÚsentation des
ISO
3166-1
noms de pays et de leurs subdivisions Partie 1: Codes de pays Second Edition
Codes for the Representation of Names of Countries and Their Subdivisions - Part 2: Country Subdvision Code Codes pour Ia
representation des noms de pays et de leurs subdivisions - Partie 2: Code pour les subdivisions de pays First Edition; Replaces ISO
ISO
3166-2
3166
Codes for the Representation of Names of Countries and Their Subdivisions - Part 3: Code for Formerly Used Names of Countries
Codes Pour La Representation Des Noms De Pays Et De Leurs Subdivisions - Partie 3: Code Pour Les Noms De Pays
ISO
3166-3
Anterieurement Utilises First Edition; Replaces ISO 3166
ISO
3167
Plastics - Multipurpose Test Specimens Fourth Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, Single Lug with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at
Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature/315 Degrees Celsius and 1 100 MPa (at Ambient
ISO
3168
Temperature)/425 Degrees Celsius - Dimensions Second Edition
ISO
3170
Petroleum Liquids - Manual Sampling Third Edition
ISO
3171
Petroleum Liquids - Automatic Pipeline Sampling Second Edition
ISO
3174
Aircraft - Connections for Checking Hydraulic Systems by Ground Appliances - Threaded Type Second Edition
Textiles - Dry Cleaning and Finishing - Part 1: Method for Assessing the Cleanability of Textiles and Garments First Edition; Technical
ISO
3175-1
Corrigendum: 10/01/2002
ISO
3175-2
Textiles - Dry Cleaning and Finishing - Part 2: Procedures for Tetrachloroethene First Edition; Technical Corrigendum: 10/01/2002
Textiles Professional care, drycleaning and wetcleaning of fabrics and garments Part 3: Procedure for testing performance when
ISO
3175-3
cleaning and finishing using hydrocarbon solvents First Edition
Textiles Professional care, drycleaning and wetcleaning of fabrics and garments Part 4: Procedure for testing performance when
ISO
3175-4
cleaning and finishing using simulated wetcleaning First Edition
ISO
3179
Coniferous Sawn Timber - Nominal Dimensions First Edition
Petroleum and natural gas industries ù Steel pipe for pipeline transportation systems Second Edition [Superseded: ISO 3183-1, ISO
ISO
3183
3183-2, ISO 3183-3]
ISO
3184
Reach and Straddle Fork-Lift Trucks - Stability Tests Second Edition; Corrigendum 1: 06-01-2000
Aerospace - Bolts, Normal Bihexagonal Head, Normal Shank, Short or Medium Length MJ Threads, Metallic Material, Coated or
ISO
3185
Uncoated, Strength Classes Less Than or Equal to 1 100 MPa - Dimensions First Edition
Aerospace - Bolts, Large Bihexagonal Head, Normal Shank, Short or Medium Length MJ Threads, Metallic Material, Coated or
ISO
3186
Uncoated, Strength Classes 1 250 MPa to 1 800 MPa - Dimensions First Edition
ISO
3187
Refractory Products - Determination of Creep in Compression First Edition
ISO
3188
Starches and Derived Products - Determination of Nitrogen Content by the Kjeldahl Method - Titrimetric Method First Edition
Sockets for Wire Ropes for General Purposes - Part 1: General Characteristics and Conditions of Acceptance First Edition; Technical
ISO
3189-1
Corrigendum 1: 02/15/2002
Sockets for Wire Ropes for General Purposes - Part 2: Special Requirements for Sockets Produced by Forging or Machined from the
ISO
3189-2
Solid First Edition
ISO
3189-3
Sockets for Wire Ropes for General Purposes - Part 3: Special Requirements for Sockets Produced by Casting First Edition
Test Conditions for Turret and Single Spindle Co-Ordinate Drilling Machines with Vertical Spindle - Testing of the Accuracy First
ISO
3190
Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, Single Lug, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1
100 MPa (at Ambient Temperature)/ 235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/ 315 Degrees Celsius and 1 100
ISO
3191
MPa (at Ambient Temperature)/ 425 Degrees Celsius - Dimensions Second Edition
Aerospace - Bolts, Normal Hexagonal Head, Normal Shank, Short or Medium Length MJ Threads, Metallic Material, Coated or
ISO
3193
Uncoated, Strength Classes Less Than or Equal to 1 100 MPa - Dimensions First Edition; Corrigendum 1: 1992
Sodium Hydroxide for Industrial Use - Sampling - Test Sample - Preparation of the Main Solution for Carrying out Certain
ISO
3195
Determinations First Edition
ISO
3196
Sodium Hydroxide for Industrial Use - Determination of Carbonates Content - Titrimetric Method First Edition
ISO
3199
Sodium Chlorate for Industrial Use - Determination of Chlorate Content - Dichromate Titrimetric Method First Edition
Aerospace - Screws, Pan Head, Internal Offset Cruciform Ribbed or Unribbed Drive, Threaded to Head, MJ Threads, Metallic
ISO
3202
Material, Coated or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa - Dimensions Second Edition
Aerospace - Bolts, Normal Bihexagonal Head, Normal or Pitch Diameter Shank, Long Length MJ Threads, Metallic Material, Coated
ISO
3203
or Uncoated, Strength Classes Less Than or Equal to 1 100 MPa - Dimensions First Edition
ISO
3205
Preferred Test Temperatures First Edition; (Amendment Slip-1976)
ISO
3208
Road Vehicles - Evaluation of Protrusions Inside Passenger Cars First Edition; Amendment-1974
Aerospace - Nuts, Anchor, Self-Locking, Floating, Two-Lug, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at
Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient
ISO
3209
Temperature)/425 Degrees Celsius - Dimensions Second Edition
Anodizing of Aluminium and Its Alloys - Assessment of Quality of Sealed Anodic Oxide Coatings by Measurement of the Loss of Mass
ISO
3210
After Immersion in Phosphoric-Chromic Acid Solution Second Edition
Anodizing of Aluminium and Its Alloys - Assessment of Resistance of Anodic Oxide Coatings to Cracking by Deformation Second
ISO
3211
Edition
ISO
3213
Polypropylene (PP) Pipes - Effect of Time and Temperature on the Expected Strength Second Edition
ISO
3214
Oil of Litsea Cubeba ( Litsea Cubeba Pers.) Second Edition
ISO
3215
Oil of Nutmeg, Indonesian Type (Mysristica Fragrans Houtt.) Second Edition
ISO
3216
Oil of Cassia, Chinese Type (Cinnamomum Aromaticum Nees, Syn. Cinnamomum Cassia Nees Ex Blume) Second Edition
ISO
3217
Oil of Lemongrass (Cymbopogon citratus) First Edition
ISO
3218
Essential Oils - Principles of Nomenclature First Edition
Plastics - Polymers/Resins in the Liquid State or as Emulsions or Dispersions - Determination of Viscosity Using a Rotational
ISO
3219
Viscometer with Defined Shear Rate Second Edition; (CEN EN ISO 3219: 1995)
ISO
3220
Copper and Copper Alloys - Determination of Arsenic - Photometric Method First Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, 90 Degree Corner, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at
Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient
ISO
3221
Temperature)/425 Degrees Celsius - Dimensions Second Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, Closed Corner, Reduced Series, with Counterbore, with MJ Threads, Classifications:
1 100 MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100
ISO
3222
MPa (at Ambient Temperature)/425 Degrees Celsius - Dimensions Second Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, Two Lug, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at Ambient
Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient
ISO
3223
Temperature)/425 Degrees Celsius - Dimensions Second Edition
Aerospace - Nuts, Anchor, Self-Locking, Floating, Single Lug, with Counterbore, with MJ Threads, Classifications: 1 100 MPa (at
Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at Ambient
ISO
3224
Temperature)/425 degrees Celsius - Dimensions Second Edition
Aerospace - Nuts, Anchor, Self-Locking, Fixed, Two Lug, Reduced Series, with Counterbore, with MJ Threads, Classifications: 1 100
MPa (at Ambient Temperature)/235 Degrees Celsius, 1 100 MPa (at Ambient Temperature)/315 Degrees Celsius and 1 100 MPa (at
ISO
3225
Ambient Temperature)/425 Degrees Celsius - Dimensions Second Edition
ISO
3228
Rolling Bearings - Cast and Pressed Housings for Insert Bearings Third Edition
Aerospace - Rivets, Solid, 100 Degree Normal Countersunk Head with Dome, Metallic Material, with or without Surface Treatment -
ISO
3230
Dimensions First Edition
ISO
3231
Paints and Varnishes - Determination of Resistance to Humid Atmospheres Containing Sulphur Dioxide Second Edition
Paints and Varnishes - Determination of Percentage Volume of Non-Volatile Matter by Measuring the Density of a Dried Coating
ISO
3233
Third Edition; Corrigendum 1 07/15/1999
ISO
3245
Rolling Bearings - Needle Roller Bearings, Drawn Cup without Inner Rings - Boundary Dimensions and Tolerances Second Edition
ISO
3248
Paints and Varnishes - Determination of the Effect of Heat Second Edition
ISO
3251
Paints, Varnishes and Plastics - Determination of Non-Volatile-Matter Content Third Edition;
ISO
3252
Powder Metallurgy - Vocabulary Metallurgie Des Poudres - Vocabulaire Fourth Edition
ISO
3253
Gas Welding Equipment - Hose Connections for Equipment for Welding, Cutting and Allied Processes Second Edition
ISO
3255
Magnesium and Magnesium Alloys - Determination of Aluminium - Chromazurol S Photometric Method First Edition
ISO
3256
Aluminium and Aluminium Alloys - Determination of Magnesium - Atomic Absorption Spectrophotometric Method First Edition
ISO
3257
Rubber Compounding Ingredients - Carbon Black - Method of Evaluation in Styrene-Butadiene Rubbers Third Edition
ISO
3258
Air Distribution and Air Diffusion - Vocabulary First Edition
ISO
3260
Pulps - Determination of Chlorine Consumption (Degree of Delignification) Second Edition
Extenders for Paints - Specifications and Methods of Test - Part 1: Introduction and General Test Methods First Edition; Replaces
ISO
3262-1
ISO 3262:1975
ISO
3262-2
Extenders for Paints - Specifications and Methods of Test - Part 2: Barytes (Natural Barium Sulfate) First Edition
ISO
3262-3
Extenders for Paints - Specifications and Methods of Test - Part 3: Blanc Fixe First Edition
ISO
3262-4
Extenders for Paints - Specifications and Methods of Test - Part 4: Whiting First Edition
ISO
3262-5
Extenders for Paints - Specifications and Methods of Test - Part 5: Natural Crystalline Calcium Carbonate First Edition
ISO
3262-6
Extenders for Paints - Specifications and Methods of Test - Part 6: Precipitated Calcium Carbonate First Edition
ISO
3262-7
Extenders for Paints - Specifications and Methods of Test - Part 7: Dolomite First Edition
ISO
3262-8
Extenders for Paints - Specifications and Methods of Test - Part 8: Natural Clay First Edition
ISO
3262-9
Extenders for Paints - Specifications and Methods of Test - Part 9: Calcined Clay First Edition; Replaces 3262:1975
ISO
3262-10
Extenders for Paints - Specificstions and Methods of Test - Part 10: Natural Talc/Chlorite in Lamellar Form First Edition
Extenders for Paints - Specificstions and Methods of Test - Part 11: Natural Talc, in Lamellar Form, Containing Carbonates First
ISO
3262-11
Edition
ISO
3262-12
Extenders for Paints - Specificstions and Methods of Test - Part 12: Muscovite-Type Mica First Edition
ISO
3262-13
Extenders for Paints - Specifications and Methods of Test - Part 13: Natural Quartz (Ground) First Edition; Replaces ISO 3262:1975
ISO
3262-14
Extenders for Paints - Specifiations and Methods of Test - Part 14: Cristobalite First Edition
ISO
3262-15
Extenders for Paints - Specifications and Methods of Test - Part 15: Vitreous Silica First Edition; Replaces ISO 3262:1975
ISO
3262-16
Extenders for Paints - Specifications and Methods of Test - Part 16: Aluminum Hydroxides First Edition
ISO
3262-17
Extenders for Paints - Specifications and Methods of Test - Part 17: Precipitated Calcium Silicate First Edition
ISO
3262-18
Extenders for Paints - Specifications and Methods of Test - Part 18: Precipitated Sodium Aluminium Silicate First Edition
ISO
3262-19
Extenders for Paints - Specifications and Methods of Test - Part 19: Precipitated Silica First Edition
ISO
3262-20
Extenders for Paints - Specifications and Methods of Test - Part 20: Fumed Silica First Edition
ISO
3262-21
Extenders for Paints - Specifications and Methods of Test - Part 21: Silica Sand (Unground Natural Quartz ) First Edition
Extenders for Paints - Specifications and Methods of Test - Part 22: Flex-Calcined Kieselguhr First Edition; Together with ISO 3262
ISO
3262-22
Parts 1-21, Supersedes ISO 3262:1975
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Wagon Tipplers Handling Rail-Borne Wagons (Rotary, Side
ISO
3265
Discharge and End Discharge) - Safety Code First Edition
ISO
3266
Eyebolts for General Lifting Purposes First Edition
ISO
3267
Road Vehicles - Headlamp Cleaners Second Edition
ISO
3269
Fasteners - Acceptance Inspection Third Edition
ISO
3270
Paints and Varnishes and Their Raw Materials - Temperatures and Humidities for Conditioning and Testing Third Edition
ISO
3271
Iron Ores - Determination of Tumble Strength Third Edition
ISO
3272-1
Microfilming of Technical Drawings and Other Drawing Office Documents - Part 1: Operating Procedures Second Edition
Microfilming of Technical Drawings and Other Drawing Office Documents - Part 2: Quality Criteria and Control of 35 mm Silver
ISO
3272-2
Gelatin Microfilms Second Edition
ISO
3272-3
Microfilming of Technical Drawings and Other Drawing Office Documents - Part 3: Aperture Card for 35 mm Microfilm Second Edition
Microfilming of Technical Drawings and Other Drawing Office Documents - Part 4: Microfilming of Drawings of Special and
ISO
3272-4
Exceptional Elongated Sizes First Edition
Geometrical Products Specifications (GPS) - Surface Texture: Profile Method - Nominal Characteristics of Contact (Stylus)
ISO
3274
Instruments Second Edition; Technical Corrigendum 1-1998
Information Processing - Implementation of the 7-Bit Coded Character Set and Its 7-Bit and 8-Bit Extensions on 3,81 mm Magnetic
ISO
3275
Tape Cassette for Data Interchange First Edition
ISO
3282
Aircraft - Dimensions for Single-Hole and Triple-Hole Mounting (Class 3) Lever-Operated Manual Switches First Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Dimensions of Bends for Use in Pneumatic Handling First
ISO
3284
Edition
ISO
3285
Road Vehicles - Ignition Coil Mounting Brackets Second Edition
ISO
3286
Single Point Cutting Tools - Corner Radii First Edition
ISO
3287
Powered Industrial Trucks - Symbols for Operator Controls and Other Displays Second Edition
ISO
3290
Rolling Bearings - Balls - Dimensions and Tolerances Third Edition [Replaced: ABMA 3290]
ISO
3291
Extra-Long Morse Taper Shank Twist Drills Second Edition
ISO
3292
Extra Long Parallel Shank Twist Drills Second Edition
ISO
3293
Morse Taper Shank Countersinks for Angles 60 Degrees, 90 Degrees and 120 Degrees Inclusive First Edition
ISO
3294
Parallel Shank Countersinks for Angles 60 Degrees, 90 Degrees and 120 Degrees Inclusive First Edition
ISO
3295
Narrow Bandsaw Blades for Woodworking - Dimensions First Edition
ISO
3297
Information and Documentation - International Standard Serial Number (ISSN) Fourth Edition
ISO
3298
Photography - Processing Chemicals - Specifications for Glacial Acetic Acid Second Edition
ISO
3299
Photography - Processing Chemicals - Specifications for 1-Phenyl-3- Pyrazolidinone Second Edition
ISO
3301
Statistical Interpretation of Data - Comparison of Two Means in the Case of Paired Observations First Edition
Rubber - Tolerances for Products - Part 1: Dimensional Tolerances First Edition; Cancels and Replaces 3302: 1990; Amendment
ISO
3302-1
1:06-01-2001
ISO
3302-2
Rubber - Tolerances for Products - Part 2: Geometrical Tolerances First Edition
ISO
3303
Rubber- or Plastics-Coated Fabrics - Determination of Bursting Strength Second Edition
ISO
3304
Plain End Seamless Precision Steel Tubes - Technical Conditions for Delivery Second Edition
ISO
3305
Plain End Welded Precision Steel Tubes - Technical Conditions for Delivery Second Edition
ISO
3306
Plain End As-Welded and Sized Precision Steel Tubes - Technical Conditions for Delivery Second Edition
ISO
3308
Routine Analytical Cigarette-Smoking Machine - Definitions and Standard Conditions Fourth Edition
Test sieves Technical requirements and testing Part 1: Test sieves of metal wire cloth Fourth Edition; Technical Corrigendum
ISO
6330-99
1:9/1/2004
ISO
3310-2
Test Sieves - Technical Requirements and Testing - Part 2: Test Sieves of Perforated Metal Plate Fourth Edition
ISO
3310-3
Test Sieves - Technical Requirements and Testing - Part 3: Test Sieves of Electroformed Sheets First Edition
ISO
3312
Sintered Metal Materials and Hardmetals - Determination of Young Modulus Second Edition; (CEN EN 23312: 1993)
ISO
3314
Shell Drills with Taper Bore (Taper Bore 1 : 30 (Included)) with Slot Drive First Edition
Assembly Tools for Screws and Nuts - Driving Parts for Hand-Operated Square Drive Socket Wrenches - Dimensions and Tests
ISO
3315
Third Edition
Assembly Tools for Screws and Nuts - Attachments for Hand-Operated Square Drive Socket Wrenches - Dimensions and Tests
ISO
3316
Third Edition
ISO
3317
Assembly Tools for Screws and Nuts - Square Drive Extension Hexagon Insert, for Power Socket Wrenches First Edition
Assembly Tools for Screws and Nuts - Double-Headed Open-Ended Wrenches, Double-Headed Ring Wrenches and Combination
ISO
3318
Wrenches - Maximum Widths of Heads Third Edition
ISO
3320
Fluid Power Systems and Components - Cylinder Bores and Piston Rod Diameters - Metric Series Second Edition
ISO
3321
Fluid Power Systems and Components - Cylinder Bores and Piston Rod Diameters - Inch Series First Edition
ISO
3323
Aircraft - Hydraulic Components - Marking to Indicate Fluid for Which Component is Approved Second Edition
ISO
3324-1
Aircraft Tyres and Rims - Part 1: Specifications Fourth Edition; Corrected and Reprinted 09/15/1998
ISO
3324-2
Aircraft Tyres and Rims - Part 2: Test Methods for Tyres Second Edition; Corrected and Reprinted 02/01/1999
Sintered Metal Materials, Excluding Hardmetals - Determination of Transverse Rupture Strength Second Edition; Amendment 1
ISO
3325
02/01/2001
ISO
3326
Hardmetals - Determination of (the Magnetization) Coercivity First Edition; (CEN EN 23326: 1993)
ISO
3327
Hardmetals - Determination of Transverse Rupture Strength Second Edition; (CEN EN 23327: 1993)
Ammonium Sulphate for Industrial Use - Determination of Ammoniacal Nitrogen Content - Titrimetric Method After Distillation First
ISO
3332
Edition
ISO
3334
Micrographics ISO resolution test chart No. 2 Description and use Third Edition
ISO
3337
T-Slot Cutters with Cylindrical Shanks and with Morse Taper Shanks Having Tapped Hole
ISO
3338-1
Cylindrical Shanks for Milling Cutters - Part 1: Dimensional Characteristics of Plain Cylindrical Shanks Fourth Edition
ISO
3338-2
Cylindrical shanks for milling cutters ù Part 2: Dimensional characteristics of flatted cylindrical shanks Sixth edition
ISO
3338-3
Cylindrical Shanks for Milling Cutters - Part 3: Dimensional Characteristics of Threaded Shanks First Edition
Tractors and Machinery for Agriculture and Forestry - Classification and Terminology - Part 0: Classification System and
ISO
3339-0
Classification Second Edition
ISO
3340
Fibre Building Boards - Determination of Sand Content First Edition
ISO
3341
Textile Glass - Yarns - Determination of Breaking Force and Breaking Elongation Third Edition
ISO
3342
Textile Glass - Mats - Determination of Tensile Breaking Force Third Edition
ISO
3343
Textile Glass - Yarns - Determination of Twist Balance Index Second Edition
ISO
3344
Reinforcement Products - Determination of Moisture Content Second Edition
ISO
3345
Wood - Determination of Ultimate Tensile Stress Parallel to Grain First Edition
ISO
3346
Wood - Determination of Ultimate Tensile Stress Perpendicular to Grain First Edition
ISO
3347
Wood - Determination of Ultimate Shearing Stress Parallel to Grain First Edition; (PNS 970: 1989)
ISO
3348
Wood - Determination of Impact Bending Strength First Edition
ISO
3349
Wood - Determination of Modulus of Elasticity in Static Bending First Edition; (PNS 971: 1989)
ISO
3350
Wood - Determination of Static Hardness First Edition
ISO
3351
Wood - Determination of Resistance to Impact Indentation First Edition
ISO
3353-1
Aerospace - Lead and Runout Threads - Part 1: Rolled External Threads First Edition; Replaces ISO 3353
ISO
3353-2
Aerospace - Lead and Runout Threads - Part 2: Internal Threads First Edition; Replaces ISO 3353
Milk and Dried Milk, Buttermilk and Buttermilk Powder, Whey and Whey Powder - Determination of Phosphatase Activity (Reference
ISO
3356
Method) First Edition
Sodium Tripolyphosphate and Sodium Pyrophosphate for Industrial Use - Determination of Total Phosphorus (V) Oxide Content -
ISO
3357
Quinoline Phosphomolybdate Gravimetric Method First Edition
Phosphoric Acid and Sodium Phosphates for Industrial Use (Including Foodstuffs) - Determination of Fluorine Content - Alizarin
ISO
3360
Complexone and Lanthanum Nitrate Photometric Method First Edition
ISO
3363
Fluorochlorinated Hydrocarbons for Industrial Use - Determination of Acidity - Titrimetric Method First Edition
ISO
3364
Indexable Hardmetal (Carbide) Inserts with Rounded Corners, with Cylindrical Fixing Hole - Dimensions Third Edition
ISO
3365
Indexable Hardmetal (Carbide) Inserts with Wiper Edges, without Fixing Hole - Dimensions Second Edition
ISO
3366
Coated Abrasives - Abrasive Rolls Second Edition
ISO
3369
Impermeable sintered metal materials and hardmetals Determination of density Second Edition
ISO
3371
Modular Units for Machine Tool Construction - Rotary Tables and Multi-Sided Centre Bases for Rotary Tables First Edition
ISO
3374
Reinforcement Products - Mats and Fabrics - Determination of Mass per Unit Area Third Edition
ISO
3375
Textile Glass - Determination of Stiffness of Rovings First Edition
ISO
3376
Leather Physical and mechanical tests Determination of tensile strength and percentage extension Second Edition; IULTCS/IUP 6
ISO
3377-1
Leather Physical and mechanical tests Determination of tear load part 1: Single edge tear First Edition; IULTCS/IUP 40
ISO
3377-2
Leather Physical and mechanical tests Determination of tear load Part 2: Double edge tear First Edition; IULTCS/IUP 8
Leather Physical and mechanical tests Determination of resistance to grain cracking and grain crack index Second Edition;
ISO
3378
IULTCS/IUP 12
ISO
3379
Leather - Determination of Distension and Strength of Grain - Ball Burst Test First Edition; (PNS 976: 1986)
ISO
3380
Leather Physical and mechanical tests Determination of shrinkage temperature up to 100 C Second Edition; IULTCS/IUP 16
ISO
3381
Railway applications Acoustics Measurement of noise inside railbound vehicles Second Edition
ISO
3382
Acoustics - Measurement of the Reverberation Time of Rooms with Reference to other Acoustical Parameters Second Edition
Rubber, vulcanized or thermoplastic - Determination of stress relaxation in compression at ambient and at elevated temperatures
ISO
3384
Fifth Edition
ISO
3385
Flexible Cellular Polymeric Materials - Determination of Fatigue by Constant-Load Pounding Third Edition; (CEN EN ISO 3385: 1995)
Polymeric Materials, Cellular Flexible - Determination of Stress-Strain Characteristic in Compression - Part 1: Low-Density Materials
ISO
3386-1
Second Edition
Flexible Cellular Polymeric Materials - Determination of Stress-Strain Characteristics in Compression - Part 2: High-Density Materials
ISO
3386-2
Second Edition
ISO
3387
Rubber - Determination of Crystallization Effects by Hardness Measurements Second Edition; Technical Corrigendum 1: 2000
ISO
3389
Aircraft - Radio Frequency Flexible Coaxial Cables - Dimensions and Electrical Characteristics First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Manganese Content - Flame Atomic Absorption
ISO
3390
Method First Edition
ISO
3391
Cryolite, Natural and Artificial - Determination of Calcium Content - Flame Atomic Absorption Method First Edition
Cryolite, Natural and Artificial, and Aluminium Fluoride for Industrial Use - Determination of Moisture Content - Gravimetric Method
ISO
3393
First Edition
ISO
3394
Dimensions of Rigid Rectangular Packages - Transport Packages Second Edition
ISO
3397
Broadleaved Wood Raw Parquet Blocks - General Characteristics First Edition
ISO
3398
Broadleaved Wood Raw Parquet Blocks - Classification of Oak Parquet Blocks First Edition
ISO
3399
Broadleaved Wood Raw Parquet Blocks - Classification of Beech Parquet Blocks First Edition
ISO
3400
Cigarettes - Determination of Alkaloids in Smoke Condensates - Spectrometric Method Third Edition
ISO
3401
Cigarettes - Determination of Alkaloid Retention by the Filters - Spectrometric Method Second Edition
ISO
3402
Tobacco and Tobacco Products - Atmosphere for Conditioning and Testing Fourth Edition
ISO
3405
Petroleum Products - Determination of Distillation Characteristics at Atmospheric Pressure Third Edition
Information Processing - Information Interchange on 3,81 mm (0.150 in) Magnetic Tape Cassette at 4 cpmm (100 cpi), Phase
ISO
3407
Encoded at 63 ftpmm (1 600 ftpi) Second Edition
ISO
3408-1
Ball screws Part 1: Vocabulary and designation Vis Ó billes Partie 1: Vocabulaire et dÚsignation Second Edition
ISO
3408-2
Ball Screws - Part 2: Nominal Diameters and Nominal Leads - Metric Series First Edition;
ISO
3408-3
Ball screws Part 3: Acceptance conditions and acceptance tests Second Edition
ISO
3408-4
Ball screws Part 4: Static axial rigidity First Edition
ISO
3408-5
Ball screws Part 5: Static and dynamic axial load ratings and operational life First Edition
ISO
3409
Passenger Cars - Lateral Spacing of Foot Controls First Edition
ISO
3410
Agricultural Machinery - Endless Variable-Speed V-Belts and Groove Sections of Corresponding Pulleys Second Edition
ISO
3411
Earth-moving machinery ù Physical dimensions of operators and minimum operator space envelope Fourth Edition
ISO
3412
Road Vehicles - Screened and Waterproof Spark- Plugs and Their Connections - Types 1A and 1B Third Edition
Textile Floor Coverings - Determination of Thickness Loss After Brief, Moderate Static Loading Second Edition (AS/NZS 2111.13:
ISO
3415
1996)
Textile Floor Coverings - Determination of Thickness Loss After Prolonged, Heavy Static Loading Second Edition (AS/NZS 2111.14:
ISO
3416
1996) [Superseded By: JSA JIS L 1021-6]
ISO
3417
Rubber - Measurement of Vulcanization Characteristics with the Oscillating Disc Curemeter Second Edition
ISO
3419
Non-Alloy and Alloy Steel Butt-Welding Fittings Second Edition; (Erratum-1982)
ISO
3423
Sulphuric Acid and Oleums for Industrial Use - Determination of Sulphur Dioxide Content - Iodometric Method First Edition
ISO
3425
Sulphur for Industrial Use - Determination of Ash at 850-900 Degrees Celsius and of Residue at 200 Degrees Celsius First Edition
ISO
3426
Sulphur for Industrial Use-Determination of Loss in Mass at 80 Degree Celsius First Edition
ISO
3427
Gaseous Halogenated Hydrocarbons (Liquefied Gases) - Taking of a Sample First Edition
ISO
3428
Sodium Fluoride for Industrial Use - Preparation and Storage of Test Samples First Edition
Sodium Fluoride Primarily Used for the Production of Aluminium - Determination of Iron Content - 1,10- 1,10-Phenanthroline
ISO
3429
Photometric Method First Edition
Sodium Fluoride Primarily Used for the Production of Aluminium - Determination of Silica Content - Reduced Molybdosilicate
ISO
3430
Spectrophotometric Method First Edition
Sodium Fluoride Primarily Used for the Production of Aluminium - Determination of Soluble Sulphates Content - Turbidimetric Method
ISO
3431
First Edition
ISO
3432
Cheese - Determination of Fat Content - Butyrometer for Van Gulik Method First Edition
ISO
3433
Cheese - Determination of Fat Content - Van Gulik Method First Edition
Shipbuilding and Marine Structures - Heated Glass Panes for Ships Rectangular Windows Second Edition; Amendment 1:
ISO
3434
7/01/2004
ISO
3435
Continuous Mechanical Handling Equipment - Classification and Symbolization of Bulk Materials First Edition
ISO
3438
Subland Twist Drills with Morse Taper Shanks for Holes Prior to Tapping Screw Threads Second Edition
ISO
3439
Subland Twist Drills with Cylindrical Shanks for Holes Prior to Tapping Screw Threads Second Edition
Machine tools Dimensions and geometric tests for self-centring chucks with two-piece jaws Part 1: Manually operated chucks with
ISO
3442-1
tongue and groove type jaws First Edition; Replaces ISO 3442 and ISO 9401
Machine tools Dimensions and geometric tests for self-centring chucks with two-piece jaws Part 2: Power-operated chucks with
ISO
3442-2
tongue and groove type jaws First Edition; Replaces ISO 3442 and ISO 9401
Machine tools ù Dimensions and geometric tests for self-centring chucks with two-piece jaws ù Part 3: Power-operated chucks with
ISO
3442-3
serrated jaws First Edition [Replaced: ISO 3442, ISO 9401]
ISO
3443-1
Tolerances for Building - Part 1: Basic Principles for Evaluation and Specification First Edition
Tolerances for Building - Part II: Statistical Basis for Predicting Fit Between Components Having a Normal Distribution of Sizes First
ISO
3443-2
Edition
ISO
3443-3
Tolerances for Building - Part 3: Procedures for Selecting Target Size and Predicting Fit First Edition
ISO
3443-4
Tolerances for Building - Part 4: Method for Predicting Deviations of Assemblies and for Allocation of Tolerances First Edition
ISO
3443-5
Building Construction - Tolerances for Building - Part 5: Series of Values to Be Used for Specification of Tolerances First Edition
Tolerances for Building - Part 6: General Principles for Approval Criteria, Control of Conformity with Dimensional Tolerance
ISO
3443-6
Specifications and Statistical Control - Method 1 First Edition
Tolerances for Building - Part 7: General Principles for Approval Criteria, Control of Conformity with Dimensional Tolerance
ISO
3443-7
Specifications and Statistical Control - Method 2 (Statistical Control Method) First Edition
ISO
3443-8
Tolerances for Building - Part 8: Dimensional Inspection and Control of Construction Work First Edition
ISO
3447
Joints in Building - General Check-List of Joint Functions First Edition
ISO
3448
Industrial Liquid Lubricants - ISO Viscosity Classification Second Edition
ISO
3449
Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements Fifth Edition
Earth-Moving Machinery - Braking Systems of Rubber-Tyred Machines - Systems and Performance Requirements and Test
ISO
3450
Procedures Third Edition
ISO
3451-1
Plastics - Determination of Ash - Part 1: General Methods Third Edition
ISO
3451-2
Plastics - Determination of Ash - Part 2: Poly(Alkylene Terephthalate) Materials Second Edition
ISO
3451-3
Plastics - Determination of Ash - Part 3: Unplasticized Cellulose Acetate First Edition
ISO
3451-4
Plastics - Determination of Ash - Part 4: Polyamides Second Edition
ISO
3451-5
Plastics - Determination of Ash - Part 5: Poly(Vinyl Chloride) Second Edition
ISO
3452
Non-Destructive Testing - Penetrant Inspection - General Principles First Edition
ISO
3452-2
Non-destructive testing Penetrant testing Part 2: Testing of penetrant materials Second Edition;
Non-Destructive Testing - Penetrant Testing - Part 3: Reference Test Blocks First Edition; Together with ISO 3452-1, ISO 3452-2 and
ISO
3452-3
ISO 3452-4 Cancels and Replaces ISO 3452:1984
Non-Destructive Testing - Penetrant Testing - Part 4: Equipment First Edition; Together with ISO 3452-1, ISO 3452-2 and ISO 3452-3
ISO
3452-4
Cancels and Replaces ISO 3452:1984
ISO
3453
Non-Destructive Testing - Liquid Penetrant Inspection - Means of Verification First Edition
ISO
3454
Liquid Flow Measurement in Open Channels - Direct Depth Sounding and Suspension Equipment Second Edition
ISO
3455
Hydrometry ù Calibration of currentmeters in straight open tanks Second Edition
ISO
3456
Aircraft - Lever-Operated Manual Switches (Class 3) - Performance Requirements First Edition
ISO
3457
Earth-Moving Machinery - Guards - Definitions and Requirements Fourth Edition
Assembled Joints Between Fittings and Polyethylene (PE) Pressure Pipes - Test of Leakproofness Under Internal Pressure First
ISO
3458
Edition
Polyethylene (PE) Pressure Pipes - Joints Assembled with Mechanical Fittings - Internal Under-Pressure Test Method and
ISO
3459
Requirement First Edition
ISO
3460
Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes - Metric Series - Dimensions of Adapter for Backing Flange First Edition
Tractors for agriculture and forestry ù Roll-over protective structures (ROPS) ù Dynamic test method and acceptance conditions
ISO
3463
Fourth edition
ISO
3465
Hand Taper Pin Reamers First Edition
ISO
3466
Machine Taper Pin Reamers with Parallel Shanks First Edition
ISO
3467
Machine Taper Pin Reamers with Morse Taper Shanks First Edition
ISO
3468
Passenger Cars - Windscreen Defrosting Systems - Test Method Second Edition
ISO
3469
Passenger Cars - Windscreen Washing Systems - Test Methods Second Edition; Amendment 1: 07/15/2006
ISO
3470
Passenger Cars - Windscreen Demisting Systems - Test Method Second Edition
Earth-Moving Machinery - Roll-Over Protective Structures - Laboratory Tests and Performance Requirements First Edition;
ISO
3471
Amendment 1-1997; Technical Corrigendum 1 12/01/2000
ISO
3475
Oil of Aniseed (Pimpinella Anisum L.) Second Edition
ISO
3476
Modular Units for Machine Tool Construction - Tenon Drive and Flanges for Mounting Multi-Spindle Heads First Edition
ISO
3493
Vanilla - Vocabulary Vanille - Vocabulaire Second Edition
ISO
3494
Statistical Interpretation of Data - Power of Tests Relating to Means and Variances First Edition
ISO
3496
Meat and Meat Products - Determination of Hydroxyproline Content Second Edition
ISO
3497
Metallic Coatings - Measurement of Coating Thickness - X-Ray Spectrometric Methods Third Edition
ISO
3500
Gas cylinders Seamless steel CO2 cylinders for fixed fire-fighting installations on ships Third Edition
ISO
3501
Assembled Joints Between Fittings and Polyethylene (PE) Pressure Pipes - Test of Resistance to Pull out First Edition
Assembled Joints Between Fittings and Polyethylene (PE) Pressure Pipes - Test of Leakproofness Under Internal Pressure When
ISO
3503
Subjected to Bending First Edition
Ropes and Cordage - Equivalence Between Natural Fibre Ropes and Man-Made Fibre Ropes for Use in the Mooring of Vessels First
ISO
3505
Edition
ISO
3506-1
Mechanical Properties of Corrosion-Resistant Stainless-Steel Fasteners - Part 1: Bolts, Screws and Studs First Edition
ISO
3506-2
Mechanical Properties of Corrosion-Resistant Stainless-Steel Fasteners - Part 2: Nuts First Edition
Mechanical Properties of Corrosion-Resistant Stainless-Steel Fasteners - Part 3: Set Screws and Similar Fasteners Not Under
ISO
3506-3
Tensile Stress First Edition
ISO
3506-4
Mechanical Properties of Corrosion-Resistant Stainless-Steel Fasteners - Part 4: Tapping Screws First Edition
ISO
3507
Laboratory Glassware - Pyknometers Second Edition
ISO
3508
Thread Run-Outs for Fasteners with Thread in Accordance with ISO 261 and ISO 262 First Edition
ISO
3509
Coffee and coffee products Vocabulary CafÚs et dÚrivÚs Vocabulaire Fourth Edition
ISO
3511-I
Process Measurement Control Functions and Instrumentation - Symbolic Representation - Part I: Basic Requirements First Edition
Process Measurement Control Functions and Instrumentation - Symbolic Representation - Part 2: Extension of Basic Requirements
ISO
3511-2
First Edition
Process Measurement Control Functions and Instrumentation - Symbolic Representation - Part 3: Detailed Symbols for Instrument
ISO
3511-3
Interconnection Diagrams First Edition
Industrial Process Measurement Control Functions and Instrumentation - Symbolic Representation - Part 4: Basic Symbols for
ISO
3511-4
Process Computer, Interface, and Shared Display/Control Functions First Edition
ISO
3512
Heavy-Duty Cranked-Link Transmission Chains Second Edition
ISO
3513
Chillies - Determination of Scoville Index Second Edition
ISO
3514
Chlorinated Polyvinyl Chloride (CPVC) Pipes and Fittings - Specification and Determination of Density First Edition
ISO
3515 CORR 1
Oil of Lavender (Lavandula Angustifolia Mill.) TECHNICAL CORRIGENDUM 1 Third Edition
ISO
3515
Oil of Lavender (Lavandula Angustifolia Mill.) Third Edition
ISO
3516
Oil of Coriander Fruits (Coriandrum Sativum L.) Second Edition
ISO
3517
Oil of Neroli (Citrus Aurantium L. ssp. Aurantium syn. Citrus Aurantium L. ssp. Amara var. Pumilia) Second Edition
ISO
3518
Oil of Sandalwood (Santalum album L.) Second Edition
ISO
3519
Oil of lime distilled, Mexican type [Citrus aurantifolia (Christm.) Swingle] Third Edition
Oil of Bergamot [Citrus Aurantium L. Subsp. Bergamia (Wight et Arnott) Engler], Italian Type Second Edition; Corrigendum 1:
ISO
3520
1/15/2002
Plastics - Unsaturated Polyester and Epoxy Resins - Determination of Overall Volume Shrinkage Second Edition; Technical
ISO
3521
Corrigendum 1: 2/15/2003
ISO
3522
Aluminium and aluminium alloys Castings - Chemical composition and mechanical properties Third Edition
ISO
3523
Oil of Cananga [Cananga Odorata (Lam.) Hook. F. Et Thomson, Forma Macrophylla] Second Edition
ISO
3524
Oil of cinnamon leaf, Sri Lanka type (Cinnamomum zeylanicum Blume) Second Edition
ISO
3525
Oil of Amyris First Edition
ISO
3526
Oil of sage, Spanish (Salvia lavandulifolia Vahl) Third Edition
ISO
3527
Oil of Parsley Fruits (Petroselinum Sativum Hoffm.) Second Edition
ISO
3528
Oil of Mandarin, Italian Type (Citrus Reticulata Blanco) Second Edition; Corrigendum 1-1998
ISO
3529-1
Vacuum Technology - Vocabulary - Part 1: General Terms First Edition
ISO
3529-2
Vacuum Technology - Vocabulary - Part 2: Vacuum Pumps and Related Terms First Edition
ISO
3529-3
Vacuum Technology - Vocabulary - Part 3: Vacuum Gauges First Edition
ISO
3530
Vacuum Technology - Mass Spectrometer-Type Leak-Detector Calibration First Edition
ISO
3534-1
Statistics Vocabulary and symbols Part 1: General statistical terms and terms used in probability Second Edition
Statistics Vocabulary and symbols Part 2: Applied statistics Statistique Vocabulaire et symboles Partie 2: Statistique appliquÚe
ISO
3534-2
Second Edition
Statistics - Vocabulary and Symbols - Part 3: Design of Experiments Statistique - Vocabulaire Et Symboles - Partie 3: Plans
ISO
3534-3
D'Experience Second Edition
ISO
3535
Forms Design Sheet and Layout Chart First Edition
ISO
3536
Road Vehicles - Safety Glazing Materials - Vocabulary Vehicules Routiers - Vitrages De Securite - Vocabulaire Second Edition
ISO
3537
Road Vehicles - Safety Glazing Materials - Mechanical Tests Third Edition
ISO
3538
Road Vehicles - Safety Glazing Materials - Test Methods for Optical Properties Second Edition
Road Vehicles - Injection Nozzle Holder with Body, Types 8 and 10, and Injection Nozzle Holder with Fixing Flats, Types 9 and 11
ISO
3539
First Edition
ISO
3540
Paper or Plastic Printing Ribbons - Characteristics of Cores First Edition
Metallic and Non-Metallic Coatings - Measurement of Thickness - Beta Backscatter Method Second Edition; TECHNICAL
ISO
3543
CORRIGENDUM 1: 12/01/2003
Steel Tubes and Fittings - Symbols for Use in Specifications - Part 1: Tubes and Tubular Accessories with Circular Cross-Section
ISO
3545-1
First Edition
ISO
3545-2
Steel Tubes and Fittings - Symbols for Use in Specifications - Part 2: Square and Rectangular Hollow Sections First Edition
ISO
3545-3
Steel Tubes and Fittings - Symbols for Use in Specifications - Part 3: Tubular Fittings with Circular Cross-Section First Edition
ISO
3546
Fibre Building Boards - Determination of Surface Finish (Roughness) First Edition
ISO
3547-1
Plain bearings Wrapped bushes Part 1: Dimensions Second Edition
ISO
3547-2
Plain bearings Wrapped bushes Part 2: Test data for outside and inside diameters Second Edition
ISO
3547-3
Plain bearings Wrapped bushes Part 3: Lubrication holes, grooves and indentations Second Edition
ISO
3547-4
Plain Bearings - Wrapped Bushes - Part 4: Materials Second Edition
Plain Bearings - Thin-Walled Half Bearings with or without Flange - Tolerances, Design Features and Methods of Test Second
ISO
3548
Edition
ISO
3549
Zinc Dust Pigments for Paints - Specifications and Test Methods Second Edition
ISO
3550-1
Cigarettes - Determination of Loss of Tobacco from the Ends - Part 1: Method Using a Rotating Cylindrical Cage First Edition
Cigarettes - Determination of Loss of Tobacco from the Ends - Part 2: Method Using a Rotating Cubic Box (Sismelatophore) First
ISO
3550-2
Edition
ISO
3551-1
Rotary Core Diamond Drilling Equipment - System A - Part 1: Metric Units First Edition
ISO
3551-2
Rotary Core Diamond Drilling Equipment - System A - Part 2: Inch Units First Edition
ISO
3552-1
Rotary Core Diamond Drilling Equipment - System B - Part 1: Metric Units First Edition
ISO
3552-2
Rotary Core Diamond Drilling Equipment - System B - Part 2: Inch Units First Edition
ISO
3553-1
Road Vehicles - High-Tension Connections for Ignition Coils and Distributors - Part 1: Socket-Type First Edition
ISO
3553-2
Road Vehicles - High-Tension Connectors for Ignition Coils and Distributors - Part 2: Plug-Type Second Edition
ISO
3559
Road Vehicles - Working Voltages for Lights Fitted to Motor Vehicles and to Their Trailers First Edition
ISO
3560
Road Vehicles - Frontal Fixed Barrier or Pole Impact Test Procedure Second Edition
ISO
3561
Information Processing - Interchangeable Magnetic Six-Disk Pack - Track Format First Edition
Information Processing - Interchangeable Magnetic Single Disk Cartridge (Top Loaded) - Physical and Magnetic Characteristics First
ISO
3562
Edition
ISO
3563
Information Processing - Interchangeable Magnetic Single-Disk Cartridge (Top Loaded) - Track Format First Edition
ISO
3564
Information Processing - Interchangeable Magnetic Eleven-Disk Pack - Physical and Magnetic Characteristics First Edition
Sodium Fluoride Primarily Used for the Production of Aluminium - Determination of Chlorides Content - Turbidimetric Method First
ISO
3566
Edition
ISO
3569
Continuous Mechanical Handling Equipment - Classification of Unit Loads First Edition
ISO
3572
Textiles - Weaves - Definitions of General Terms and Basic Weaves First Edition
ISO
3573
Hot-Rolled Carbon Steel Sheet of Commercial and Drawing Qualities Third Edition
ISO
3574
Cold-Reduced Carbon Steel Sheet of Commercial and Drawing Qualities Third Edition
ISO
3575
Continuous hot-dip zinc-coated carbon steel sheet of commercial and drawing qualities Third Edition
Covered Electrodes for Manual Arc Welding of Welding consumables Covered electrodes for manual metal arc welding of creep-
ISO
3580
resisting steels Classification Second Edition
Welding Consumables - Covered Electrodes for Manual Metal Arc Welding of Stainless and Heat-Resisting Steels - Classification
ISO
3581
Second Edition
Flexible cellular polymeric materials ù Laboratory assessment of horizontal burning characteristics of small specimens subjected to a
ISO
3582 AMD 1
small flame AMENDMENT 1 Second Edition
Flexible Cellular Polymeric Materials - Laboratory Assessment of Horizontal Burning Characteristics of Small Specimens Subjected to
ISO
3582
a Small Flame Second Edition
ISO
3583
Road Vehicles - Pressure Test Connection for Compressed-Air Pneumatic Braking Equipment Third Edition
ISO
3584
Road Vehicles - Drawbar Couplings - Interchangeability Second Edition
ISO
3585
Borosilicate Glass 3.3 - Properties Third Edition
ISO
3586
Glass Plant, Pipeline and Fittings - General Rules for Testing, Handling and Use First Edition
Glass Plant, Pipeline and Fittings - Pipeline and Fittings of Nominal Bore 15 to 150 mm - Compatibility and Interchangeability First
ISO
3587
Edition; (Erratum-1979)
ISO
3588
Spices and Condiments - Determination of Degree of Fineness of Grinding - Hand Sieving Method (Reference Method) First Edition
ISO
3589
Modular Units for Machine Tool Construction - Integral Way Columns First Edition; Amendment 1: 1982
ISO
3590
Modular units for machine tool construction - Spindle Units First Edition
ISO
3591
Sensory Analysis - Apparatus - Wine-Tasting Glass First Edition
ISO
3593
Starch - Determination of Ash Second Edition; (CEN EN ISO 3593: 1981)
ISO
3594
Milk Fat - Detection of Vegetable Fat by Gas-Liquid Chromatography of Sterols (Reference Method) First Edition
ISO
3595
Milk Fat - Detection of Vegetable Fat by the Phytosteryl Acetate Test First Edition
Animal and Vegetable Fats and Oils - Determination of Unsaponifiable Matter - Method Using Diethyl Ether Extraction First Edition;
ISO
3596
Cancels and Replaces ISO 3596-1:1988 and its Amendment 1:1997
Animal and Vegetable Fats and Oils - Determination of Unsaponifiable Matter - Method Using Hexane Extraction First Edition
ISO
18609
[Superseded: ISO 3596-2]
Textile-Glass-Reinforced Plastics - Determination of Mechanical Properties on Rods Made of Roving-Reinforced Resin - Part 1:
ISO
3597-1
General Considerations and Preparation of Rods Second Edition
Textile-Glass-Reinforced Plastics - Determination of Mechanical Properties on Rods Made of Roving-Reinforced Resin - Part 2:
ISO
3597-2
Determination of Flexural Strength Second Edition
Textile-Glass-Reinforced Plastics - Determination of Mechanical Properties on Rods Made of Roving-Reinforced Resin - Part 3:
ISO
3597-3
Determination of Compressive Strength Second Edition
Textile-Glass-Reinforced Plastics - Determination of Mechanical Properties on Rods Made of Roving-Reinforced Resin - Part 4:
ISO
3597-4
Determination of Apparent Interlaminar Shear Strength Second Edition
ISO
3598
Textile Glass - Yarns - Basis for a Specification Second Edition
ISO
3599
Vernier callipers reading to 0,l and 0,05 mm First Edition
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Operator s Manuals - Content and
ISO
3600
Presentation Third Edition
ISO
3601-1
Fluid Power Systems - O-rings - Part 1: Inside Diameters, Cross-Sections, Tolerances and Size Identification Code Third Edition
ISO
3601-3
Fluid power systems O-rings Part 3: Quality acceptance criteria Second Edition
ISO
3601-5
Fluid Power Systems - O-Rings - Part 5: Suitability of Elastomeric Materials for Industrial Applications First Edition
ISO
3602
Documentation - Romanization of Japanese (Kana Script) First Edition
Fittings for Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes with Elastic Sealing Ring Type Joints - Pressure Test for
ISO
3603
Leakproofness First Edition
Fitting for Unplasticized Polyvinyl Chloride (PVC) Pressure Pipes with Elastic Sealing Ring Type Joints - Pressure Test for
ISO
3604
Leakproofness Under Conditions of External Hydraulic Pressure First Edition
ISO
3610
Modular units for machine tool construction - Support brackets First Edition
ISO
3611
Micrometer Callipers for External Measurement First Edition
ISO
3613
Chromate Conversion Coatings on Zinc,Cadmium, Aluminium-Zinc Alloys and Zinc-Aluminium Alloys - Test Methods Second Edition
Textile Glass - Chopped-Strand and Continuous-Filament Mats - Determination of Average Thickness, Thickness Under Load and
ISO
3616
Recovery After Compression Second Edition
ISO
3617
Photography - Processing Chemicals - Specifications for Sodium Hydroxide Second Edition
ISO
3618
Photography - Processing Chemicals - Specifications for Benzotriazole Second Edition
ISO
3619
Photography - Processing Chemicals - Specifications for Ammonium Thiosulfate Solution Second Edition
Photography - Processing Chemicals - Specifications for Aluminium Potassium Sulfate Second Edition; (Corrected and Reprinted -
ISO
3620
1995)
ISO
3621
Photography - Processing Chemicals - Specifications for Sodium Tetraborate Decahydrate Second Edition
ISO
3622
Photography - Processing Chemicals - Specifications for Ammonium Thiocyanate Second Edition
ISO
3623
Photography - Processing Chemicals - Specifications for Anhydrous Potassium Carbonate Second Edition
ISO
3624
Photography - Processing Chemicals - Specifications for Potassium Ferricyanide Second Edition
ISO
3625
Photography - Processing Chemicals - Specifications for Potassium Hydroxide Second Edition
ISO
3626
Photography - Processing Chemicals - Specifications for Potassium Thiocyanate Second Edition
ISO
3627
Photography - Processing Chemicals - Specifications for Anhydrous Sodium Metabisulfite Third Edition
ISO
3628
Photography - Processing Chemicals - Specifications for Boric Acid, Granular Second Edition
ISO
3629
Photography - Processing Chemicals - Specifications for Potassium Metabisulfite Third Edition
Dental Root-Canal Instruments - Part 1: Files, Reamers, Barbed Broaches, Rasps, Paste Carriers, Explorers and Cotton Broaches
ISO
3630-1
First Edition; (CEN EN ISO 3630-1: 1994) (CAN/CSA-Z349.48.2-94)
ISO
3630-2
Dental Root Canal Instruments - Part 2: Enlargers Second Edition
ISO
3630-3
Dental Root-Canal Instruments - Part 3: Condensers, Pluggers and Spreaders First Edition
ISO
3631
Citrus Fruits - Guide to Storage First Edition
Plastics Piping Systems for Soil and Waste Discharge (Low and High Temperature) Inside Buildings - Unplasticized Poly(Vinyl
ISO
3633
Chloride) (PVC-U) Second Edition
ISO
3634
Vegetable Products - Determination of Chloride Content First Edition
ISO
3635
Size Designation of Clothes - Definitions and Body Measurement Procedure Third Edition
ISO
3636
Size Designation of Clothes - Men s and Boys Outerwear Garments First Edition; Erratum: 1978; Corrigendum 1: 1990
ISO
3637
Size Designation of Clothes - Womens and Girls Outerwear Garments First Edition; Corrigendum 1: 1990
ISO
3638
Size Designation of Clothes - Infants Garments First Edition
Cinematography - Projection Reels/Spools 75 to 312 mm Diameter for 8 mm Type S Motion-Picture Film - Dimensions and
ISO
3639
Specifications First Edition
Cinematography - Motion-Picture Prints and Sound Records for International Exchange of Television Programmes - Specifications
ISO
3640
Second Edition
Cinematography - Motion-Picture Camera Cartridge 8 mm Type S Model II - Cartridge Fit and Take-Up Core Drive - Dimensions and
ISO
3641
Specifications First Edition
ISO
3642
Cinematography - Cemented or Welded Splices on 8 mm Type S Motion-Picture Film for Projector Use - Dimensions Second Edition
ISO
3644
Cinematography - Spindles for 8 mm Type R Motion-Picture Cameras and Projectors - Dimensions First Edition
Cinematography - Image Area Produced by 8 mm Type S Motion-Picture Camera Aperture and Maximum Projectable Image Area -
ISO
3645
Positions and Dimensions Second Edition
Cinematography - Motion- Picture Camera Cartridge 8 mm Type S Model II - Slots, Projections and Cartridge Hole for Indicating Film
ISO
3646
Speed, Colour Balance and Film Identification - Dimensions and Positions First Edition
ISO
3647
Cinematography - Spindles for 16 mm Motion-Picture Camera Spools and Projector Reels - Dimensions First Edition
ISO
3648
Aviation Fuels - Estimation of Net Specific Energy Second Edition; Corrigendum 1: 1996
ISO
3649
Cleaning Equipment for Air or Other Gases - Vocabulary First Edition
ISO
3650
Geometrical Product Specifications (GPS) - Length Standards - Gauge Blocks Second Edition
Determination of Resistance to Intergranular Corrosion of Stainless Steels - Part 1: Austenitic and Ferritic-Austenitic (Duplex)
ISO
3651-1
Stainless Steels - Corrosion Test in Nitric Acid Medium by Measurement of Loss in Mass (Huey Test) Second Edition
Determination of Resistance to Intergranular Corrosion of Stainless Steels - Part 2: Ferritic, Austenitic and Ferritic-Austenitic (Duplex)
ISO
3651-2
Stainless Steels - Corrosion Test in Media Containing Sulfuric Acid Second Edition
ISO
3652
Shipbuilding - Inland Vessels - Rope Reels First Edition
ISO
3653
Cinematography - Spindles for 8 mm Type S Motion-Picture Projector Reels/Spools - Dimensions First Edition
Acceptance Conditions for Vertical Turning and Boring Lathes with One or Two Columns and a Single Fixed or Movable Table -
ISO
3655
General Introduction and Testing of the Accuracy Second Edition
ISO
3656
Animal and Vegetable Fats and Oils - Determination of Ultraviolet Absorbance Expressed as Specific UV Extinction Third Edition
ISO
3657
Animal and Vegetable Fats and Oils - Determination of Saponification Value Third Edition
ISO
3659
Fruit and Vegetables - Ripening After Cold Storage First Edition
ISO
3660
Fishing Nets - Mounting and Joining of Netting - Terms and Illustrations First Edition
ISO
3661
End-Suction Centrifugal Pumps - Baseplate and Installation Dimensions First Edition; (CEN EN 23661: 1993)
ISO
3662
Hydraulic Fluid Power - Pumps and Motors - Geometric Displacements First Edition
ISO
3663
Polyethylene (PE) Pressure Pipes and Fittings, Metric Series - Dimensions of Flanges First Edition
ISO
3664
Viewing Conditions - Graphic Technology and Photography Second Edition
ISO
3665
Photography - Intra-Oral Dental Radiographic Film - Specification Second Edition
ISO
3668
Paints and Varnishes - Visual Comparison of the Colour of Paints Second Edition
ISO
3669
Vacuum Technology - Bakable Flanges - Dimensions First Edition
ISO
3671
Plastics - Aminoplastic Moulding Materials - Determination of Volatile Matter First Edition
ISO
3672-1
Plastics - Unsaturated Polyester Resins (UP-R) - Part 1: Designation System Second Edition
ISO
3672-2
Plastics - Unsaturated Polyester Resins (UP-R) - Part 2: Preparation of Test Specimens and Determination of Properties First Edition
ISO
3673-1
Plastics - Epoxy Resins - Part 1: Designation Second Edition
ISO
3673-2
Plastics - Epoxy Resins - Part 2: Preparation of Test Specimens and Determination of Properties Second Edition
ISO
3674
Shipbuilding - Inland Vessels - Deck Rail First Edition
ISO
3675
Crude Petroleum and Liquid Petroleum Products - Laboratory Determination of Density - Hydrometer Method Third Edition;;
ISO
3676
Packaging - Unit Load Sizes - Dimensions First Edition
ISO
3677
Filler Metals for Soft Soldering, Brazing and Braze Welding - Designation Second Edition
ISO
3678
Paints and Varnishes - Print-Free Test First Edition; (CEN EN ISO 3678: 1995) (PNS 682: 1990)
ISO
3679
Determination of flash point Rapid equilibrium closed cup method Third Edition
ISO
3680
Determination of flash/no flash Rapid equilibrium closed cup method Fourth Edition
ISO
3681
Binders for Paints and Varnishes - Determination of Saponification Value - Titrimetric Method Third Edition
ISO
3684
Conveyors Belts - Determination of Minimum Pulley Diameters Second Edition
ISO
3685
Tool-Life Testing with Single-Point Turning Tools Second Edition
Test Conditions for High Accuracy Turret and Single Spindle Coorinate Drilling and Boring Machines with Table of Fixed Height with
Vertical Spindle - Testing of the Accuracy - Part 1: Single Column Type Machines First Edition; this First Edition Together with ISO
ISO
3686-1
3686-2 Replaces ISO 3638: 1976
Test Conditions for High Accuracy Turret and Single Spindle Coorinate Drilling and Boring Machines with Table of Fixed Height with
Vertical Spindle - Testing of the Accuracy - Part 2: Portal Type Machines with Moving Table First Edition; this First Edition Together
ISO
3686-2
with ISO 3686-1 Replaces ISO 3638: 1976
ISO
3688
Pulp - Preparation of Laboratory Sheets for the Measurement of Diffuse Blue Reflectance Factor (ISO Brightness) Second Edition
ISO
3689
Paper and Board - Determination of Bursting Strength After Immersion in Water Second Edition
ISO
3690
Welding and Allied Processes - Determination of Hydrogen Content in Ferritic Steel Arc Weld Metal Second Edition
ISO
3691
Powered Industrial Trucks - Safety Code Second Edition; Amendment 1: 1983
Information Processing - Reels and Cores for 25,4 mm (1 in) Perforated Paper Tape for Information Interchange - Dimensions First
ISO
3692
Edition
ISO
3696
Water for Analytical Laboratory Use - Specification and Test Methods First Edition
ISO
3699
Anhydrous Hydrogen Fluoride for Industrial Use - Determination of Water Content - Karl Fischer Method First Edition
ISO
3703
Acid-Grade and Ceramic-Grade Fluorspar - Determination of Flotation Agents Second Edition
ISO
3704
Sulphur for Industrial Use - Determination of Acidity - Titrimetric Method First Edition
ISO
3705
Sulphur for Industrial Use - Determination of Arsenic Content - Silver Diethyldithiocarbamate Photometric Method First Edition
Phosphoric Acid for Industrial Use (Including Foodstuffs) - Determination of Total Phosphorus (V) Oxide Content - Quinoline
ISO
3706
Phosphomolybdate Gravimetric Method First Edition; (Erratum-1978)
Phosphoric Acid for Industrial Use (Including Foodstuffs) - Determination of Calcium Content - Flame Atomic Absorption Method First
ISO
3707
Edition (PNS 855:1989)
Lead Chromate Pigments and Lead Chromate- Molybdate Pigments - Specifications and Methods of Test Second Edition; (Corrected
ISO
3711
and Reprinted - 1991)
ISO
3713
Ferroalloys - Sampling and Preparation of Samples - General Rules First Edition
ISO
3714
Oil of Pennyroyal First Edition
ISO
3715
Shipbuilding - Ship Screw Propellers - List of Equivalent Terms First Edition; Amendment 1: 1986
ISO
3715-1
Ships and Marine Technology - Propulsion Plants for Ships - Part 1: Vocabulary for Geometry of Propellers First Edition
ISO
3715-2
Ships and Marine Technology - Propulsion Plants for Ships - Part 2: Vocabulary for Controllable-Pitch Propeller Plants First Edition
ISO
3719
Mechanical Vibration - Symbols for Balancing Machines and Associated Instrumentation Second Edition
Black Tea - Definition and Basic Requirements Third Edition; Technical Corrigendum 1: 2/15/1992; Technical Corrigendum 2:
ISO
3720
3/15/2004
Hydraulic Fluid Power - Fluid Sample Containers - Qualifying and Controlling Cleaning Methods First Edition Supersedes NFPA
ISO
3722
B93.20M
ISO
3723
Hydraulic Fluid Power - Filter Elements - Method for End Load Test First Edition
ISO
3724
Hydraulic fluid power - Filter elements - Determination of resistance to flow fatigue using particulate contaminant Second Edition
ISO
3726
Instant Coffee - Determination of Loss in Mass at 70 Degrees Celsius Under Reduced Pressure First Edition
Butter - Determination of Moisture, Not-Fat Solids and Fat Contents - Part 1: Determination of Moisture Content (Reference Method)
ISO
3727-1
First Edition; IDF 80-1; Together With ISO 3727-2 and 3727-3 Cancels and Replaces ISO 3727:1977
Butter - Determination of Moisture, Not-Fat Solids and Fat Contents - Part 2: Determination of Non-Fat Solids Content (Reference
ISO
3727-2
Method) First Edition; IDF 80-1; Together With ISO 3727-2 and 3727-3 Cancels and Replaces ISO 3727:1977
ISO
3727-3
Butter - Determination of Moisture, Non-Fat Solids and Fat Contents - Part 3: Calculation of Fat Content First Edition
ISO
3728
Ice-Cream and Milk Ice - Determination of Total Solids Content (Reference Method) Second Edition
ISO
3729
Fibre Building Boards - Determination of Surface Stability First Edition
ISO
3730
Shipbuilding - Mooring Winches Second Edition; (Corrected and Reprinted - 1989)
Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 S (supplementary) for
ISO
3731
vehicles with 24 V nominal supply voltage Fourth Edition
Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 S (supplementary) for
ISO
3732
vehicles with 12 V nominal supply voltage Fourth Edition
ISO
3733
Petroleum Products and Bituminous Materials - Determination of Water - Distillation Method Second Edition
ISO
3734
Petroleum Products - Determination of Water and Sediment in Residual Fuel Oils - Centrifuge Method Second Edition
ISO
3735
Crude Petroleum and Fuel Oils - Determination of Sediment - Extraction Method Second Edition
ISO
3738-1
Hardmetals - Rockwell Hardness Test (Scale A) - Part 1: Test Method First Edition
ISO
3738-2
Hardmetals - Rockwell Hardness Test (Scale A) - Part 2: Preparation and Calibration of Standard Test Blocks First Edition
Industrial tyres and rims ù Part 1: Pneumatic tyres (metric series) on 5
tapered or flat base rims ù Designation, dimensions and
ISO
3739-1
marking Second Edition
Industrial Tyres and Rims - Part 2: Pneumatic Tyres (Metric Series) on 5 Degree Tapered or Flat Base Rims - Load Ratings First
ISO
3739-2
Edition
ISO
3739-3
Industrial Tyres and Rims - Part 3: Rims First Edition
ISO
3740
Acoustics - Determination of Sound Power Levels of Noise Sources - Guidelines for the Use of Basic Standards Second Edition
Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure - Precision Methods for Reverberation
ISO
3741
Rooms Third Edition; Replaces ISO 3742; 1988; Technical Corrigendum 1:03/01/2001
Acoustics - Determination of Sound Power Levels of Noise Sources - Engineering Methods for Small, Movable Sources in
ISO
3743-1
Reverberant Fields Part 1: Comparison Method for Hard-Walled Test Rooms First Edition; (CEN EN ISO 3743-1: 1995)
Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure - Engineering Methods for Small, Movable
ISO
3743-2
Sources in Reverberant Fields - Part 2: Methods for Special Reverberation Test Rooms First Edition;
Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure - Engineering Method in an Essentially
ISO
3744
Free Field over a Reflecting Plane Second Edition; (CEN EN ISO 3744: 1995)
Acoustics Determination of sound power levels of noise sources using sound pressure Precision methods for anechoic and hemi-
ISO
3745
anechoic rooms Second Edition
Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure - Survey Method Using an Enveloping
ISO
3746
Measurement Surface over a Reflecting Plane (CEN EN ISO 3746: 1995) Second Edition; Corrigendum 1: 1995
Acoustics - Determination of Sound Power Levels of Noise Sources Using Sound Pressure - Comparison Method in Situ Second
ISO
3747
Edition
ISO
3750
Zinc alloys Determination of magnesium content Flame atomic absorption spectrometric method Second Edition
ISO
3754
Steel - Determination of Effective Depth of Hardening After Flame or Induction Hardening First Edition
ISO
3755
Cast Carbon Steels for General Engineering Purposes Second Edition
ISO
3756
Oil of Cubeb First Edition
ISO
3757
Oil of patchouli [Pogostemon cablin (Blanco) Benth.] Second Edition
ISO
3758
Textiles - Care Labelling Code Using Symbols Second edition
Textiles ù Preparation, marking and measuring of fabric specimens and garments in tests for determination of dimensional change
ISO
3759
Fourth Edition
ISO
3760
Oil of Celery Seed (Apium Graveolens L.) Second Edition
ISO
3761
Oil of rosewood, Brazilian type [Aniba rosaeodora Ducke or Aniba parviflora (Meisn.) Mez.] Third edition; Replaces ISO 7353: 1985
ISO
3763
Wrought Steels - Macroscopic Methods for Assessing the Content of Non-Metallic Inclusions First Edition
ISO
3764
Timekeeping Instruments - Movements - Types, Dimensions and Nomenclature Third Edition
ISO
3765
Timekeeping Instruments - Wristwatches - Dimensions of Bracelet-to-Case Fastening Elements Second Edition
ISO
3766
Construction Drawings - Simplified Representation of Concrete Reinforcement Third Edition; Replaces ISO 4066
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Symbols for Operator Controls and Other
ISO
3767-1
Displays - Part 1: Common Symbols Third Edition
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Symbols for Operator Controls and Other
Displays - Part 2: Symbols for Agricultural Tractors and Machinery Second Edition; Amendment 1: 02/15/1995; Amendment 2:
ISO
3767-2
Additional Symbols; 12/15/1998; Amendment 3: 03/15/2000
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Symbols for Operator Controls and Other
ISO
3767-3
Displays - Part 3: Symbols for Powered Lawn and Garden Equipment Second Edition CEN EN ISO 3767-3: 1996
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Symbols for Operator Controls and Other
ISO
3767-4
Displays - Part 4: Symbols for Forestry Machinery - Amendment 1: Additional Symbols First Edition; Amendment 1 10/01/2000
Tractors, Machinery for Agriculture and Forestry, Powered Lawn and Garden Equipment - Symbols for Operator Controls and Other
ISO
3767-5
Displays - Part 5: Symbols for Manual Portable Forestry Machinery First Edition; Amendment 1:06-01-2001
ISO
3771
Petroleum Products - Determination of Base Number - Perchloric Acid Potentiometric Titration Method Second Edition
Photography - Rolls of Sensitized Material for the Pre-Press Industry - Dimensions and Related Requirements Third Edition; Cancels
ISO
3772
and Replaces ISO 6407:1992, ISO 6408:1991, and ISO 11313:1994
ISO
3773
Cinematography - Tape Splices for 8 mm Type S Motion-Picture Film for Projector Use - Dimensions Second Edition
Cinematography - 35 mm Motion-Picture Film Perforated 8 mm Type S (1-3-5-7-0) and (1-0) - Cutting and Perforating Dimensions
ISO
3774
Third Edition
Tractors and machinery for agriculture Seat belts Part 1: Anchorage location requirements First Edition; Together with ISO 3776-2
ISO
3776-1
replaces ISO 3776: 1989
ISO
3776-2
Tractors and machinery for agriculture ù Seat belts ù Part 2: Anchorage strength requirements First edition [Cancelled: ISO 3776]
ISO
3779
Road Vehicles - Vehicle Identification Number (VIN) - Content and Structure Third Edition
ISO
3780
Road Vehicles - World Manufacturer Identifier (WMI) Code Second Edition
ISO
3781
Paper and Board - Determination of Tensile Strength After Immersion in Water Second Edition
Paper and board Determination of resistance to picking Accelerated speed method using the IGT-type tester (electric model)
ISO
3783
Second Edition
ISO
3784
Road Vehicles - Measurement of Impact Velocity in Collision Tests First Edition
ISO
3785
Metallic materials Designation of test specimen axes in relation to product texture Second Edition
ISO
3786
Shipbuilding - Inland Navigation Towing Hooks - Scale of Tractive Efforts First Edition
Information Processing - 9-Track, 12,7 mm (0,5 in) Wide Magnetic Tape for Information Interchange Using Phase Encoding at 126
ISO
3788
ftpmm (3 200 ftpi) - 63 cpmm (1 600 cpi) Second Edition
ISO
3790
Fishing Nets - Determination of Elongation of Netting Yarns First Edition
ISO
3791
Office Machines and Data Processing Equipment - Keyboard Layouts for Numeric Applications First Edition
ISO
3792
Adding Machines - Layout of Function Keyboard First Edition
Essential Oils (Containing Tertiary Alcohols) - Estimation of Free Alcohols Content by Determination of Ester Value After Acetylation
ISO
3794
First Edition
Road Vehicles, and Tractors and Machinery for Agriculture and Forestry - Determination of Burning Behaviour of Interior Materials
ISO
3795
Second Edition
ISO
3796
Ships and Marine Technology - Clear Openings for External Single-Leaf Doors Second Edition
ISO
3797
Shipbuilding - Vertical Steel Ladders First Edition
ISO
3800
Threaded Fasteners - Axial Load Fatigue Testing - Test Methods and Evaluation of Results First Edition;
ISO
3801
Textiles - Woven Fabrics - Determination of Mass per Unit Length and Mass per Unit Area First Edition
Information Processing - General Purpose Reels with 8 mm (5/16 in) Centre Hole for Magnetic Tape for Interchange Instrumentation
ISO
3802
Applications First Edition
ISO
3803
Road Vehicles - Hydraulic Pressure Test Connection for Braking Equipment Second Edition
Cylinders for Acetylene - Basic Requirements - Part 1: Cylinders without Fusible Plugs First Edition; This First Edition Together with
ISO
3807-1
3807-2, Cancels and Replaces ISO 3807: 1977
Cylinders for Acetylene - Basic Requirements - Part 2: Cylinders with Fusible Plugs First Edition; This First Edition Together with 3807-
ISO
3807-2
1, Cancels and Replaces ISO 3807: 1977
ISO
3808
Road Vehicles - Unscreened High-Voltage Ignition Cables - General Specifications, Test Methods and Requirements First Edition
ISO
3809
Oil of lime (cold pressed), Mexican type [Citrus aurantifolia (Christm.) Swingle], obtained by mechanical means Third Edition
ISO
3810
Floor Tiles of Agglomerated Cork - Methods of Test Second Edition; (Corrected and Reprinted - 1992)
ISO
3813
Resilient floor coverings Cork floor tiles Specification Third Edition
ISO
3815-1
Zinc and zinc alloys Part 1: Analysis of solid samples by optical emission spectrometry First edition
Zinc and zinc alloys Part 2: Analysis by inductively coupled plasma optical emission spectrometry First Edition; Supersedes ISO
ISO
3815-2
3815
ISO
3819
Laboratory Glassware - Beakers First Edition
ISO
3820
Cinematography - Sprockets for 8 mm Type S Motion-Picture Film - Dimensions and Design First Edition
ISO
3821
Gas Welding Equipment - Rubber Hoses for Welding, Cutting and Allied Processes Third Edition
Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 1: Method
ISO
3822-1
of Measurement Third Edition
Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 2:
ISO
3822-2
Mounting and Operating Conditions for Draw-Off Taps and Mixing Valves Second Edition; (CEN EN ISO 3822-2: 1995)
Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 3:
ISO
3822-3
Mounting and Operating Conditions for In-Line Valves and Appliances Second Edition
Acoustics - Laboratory Tests on Noise Emission from Appliances and Equipment Used in Water Supply Installations - Part 4:
ISO
3822-4
Mounting and Operating Conditions for Special Appliances Second Edition
ISO
3823-1
Dental Rotary Instruments - Burs - Part 1: Steel and Carbide Burs Second Edition
ISO
3823-2
Dentistry Rotary bur instruments Part 2: Finishing burs Second Edition
Plastics collapsible containers for human blood and blood components Part 1: Conventional containers First Edition; Replaces ISO
ISO
3826-1
3826
Plastics collapsible containers for human blood and blood components Part 3: Blood bag systems with integrated features First
ISO
3826-3
Edition
ISO
3828
Shipbuilding and Marine Structures - Deck Machinery - Vocabulary Second Edition
Petroleum Products - Determination of Lead Content of Gasoline - Iodine Monochloride Method Third Edition; (CEN EN ISO 3830:
ISO
3830
1995) Also Known As BS 2000 PART 270/96; [Use: IP 270/96]
ISO
3832
Passenger Cars - Luggage Compartments - Method of Measuring Reference Volume Third Edition
ISO
3833
Road Vehicles - Types - Terms and Definitions Second Edition
Quality requirements for fusion welding - of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality
ISO
3834-1
requirements Second edition
ISO
3834-2
Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements Second edition
ISO
3834-3
Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements Second edition
ISO
3834-4
Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements Second edition
Quality requirements for fusion welding of metallic materials Part 5: Documents with which it is necessary to conform to claim
ISO
3834-5 CORR 1
conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 TECHNICAL CORRIGENDUM 1 First edition
Quality requirements for fusion welding of metallic materials Part 5: Documents with which it is necessary to conform to claim
ISO
3834-5
conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 First edition
ISO
3835-1
Equipment for Vine Cultivation and Wine Making - Vocabulary - Part I First Edition
ISO
3835-2
Equipment for Vine Cultivation and Wine Making - Vocabulary - Part II First Edition
ISO
3835-3
Equipment for Vine Cultivation and Wine Making - Vocabulary - Part 3 First Edition
ISO
3835-4
Equipment for Vine Cultivation and Wine Making - Vocabulary - Part 4 First Edition
ISO
3835-5
Equipment for Vine Cultivation and Wine Making - Vocabulary - Part 5 First Edition
Liquid Petroleum Products - Determination of Hydrocarbon Types - Fluorescent Indicator Adsorption Method First Edition;
ISO
3837
Corrigendum 1: 1994; Corrigendum 2: 1996
Crude petroleum and liquid or solid petroleum products Determination of density or relative density Capillary-stoppered pyknometer
ISO
3838
and graduated bicapillary pyknometer methods Second Edition
ISO
3839
Petroleum Products - Determination of Bromine Number of Distillates and Aliphatic Olefins - Electrometric Method Second Edition
ISO
3841
Petroleum Waxes - Determination of Melting Point (Cooling Curve) First Edition
ISO
3842
Road vehicles Fifth wheels Interchangeability Fourth Edition
ISO
3846
Liquid Flow Measurement in Open Channels by Weirs and Flumes - Rectangular Broad-Crested Weirs Second Edition
Liquid Flow Measurement in Open Channels by Weirs and Flumes - End-Depth Method for Estimation of Flow in Rectangular
ISO
3847
Channels with a Free Overfall First Edition
ISO
3848
Oil of Citronella, Java Type Second Edition; Technical Corrigendum 1: 11/01/2002
ISO
3849
Oil of Citronella, Sri Lanka Type [Cymbopogon Nardus (L.) W. Watson Var. Lenabatu Stapf.] Second Edition
ISO
3850
Resilient floor coverings Determination of apparent density of composition cork First Edition
ISO
3852
Iron ores for blast furnace and direct reduction feedstocks ù Determination of bulk density Third Edition
ISO
3853
Road Vehicles - Towing Vehicle Coupling Device to Tow Caravans or Light Trailers - Mechanical Strength Test Second Edition
ISO
3855
Milling Cutters - Nomenclature First Edition; Corrigendum 1: 1996
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 1: Determination of Lead Content - Flame Atomic Absorption
ISO
3856-1
Spectrometric Method and Dithizone Spectrophotometric Method Third Edition; (AS/NZS 1580.501.1:1994) 1994) (PNS 530: 1991)"
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 2: Determination of Antimony Content - Flame Atomic
ISO
3856-2
Absorption Spectrometric Method and Rhodamine B Spectrophotometric Method Second Edition"
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 3: Determination of Barium Content - Flame Atomic Emission
ISO
3856-3
Spectrometric Method Second Edition"
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 4: Determination of Cadmium Content - Flame Atomic
ISO
3856-4
Absorption Spectrometric Method and Polarographic Method Second Edition"
Paints and Varnishes - Determination ofSoluble" Metal Content- Part 5: Determination of Hexavalent Chromium Content of the
ISO
3856-5
Pigment Portion of the Liquid Paint or the Paint in Powder Form - Diphenyl- carbazide Spectro- photometric Method Second Edition"
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 6: Determination of Total Chromium Content of the Liquid
ISO
3856-6
Portion of the Paint - Flame Atomic Absorption Spectrometric Method Second Edition"
Paints and Varnishes - Determination ofSoluble" Metal Content - Part 7: Determination of Mercury Content of the Pigment Portion of
ISO
3856-7
the Paint and of the Liquid Portion of Water-Dilutable Paints - Flameless Atomic Absorption Spectrometric Method First Edition"
ISO
3857-1
Compressors, Pneumatic Tools and Machines - Vocabulary - Part I: General First Edition
ISO
3857-2
Compressors Pneumatic Tools and Machines - Vocabulary - Part II: Compressors First Edition
ISO
3857-3
Compressors, Pneumatic Tools and Machines - Vocabulary - Part 3: Pneumatic Tools and Machines Second Edition
Rubber compounding ingredients Carbon black Determination of light transmittance of toluene extract Second Edition; Replaces
ISO
3858
ISO 3858-1:1990 and ISO 3858-2:1990
ISO
3859
Inverse Dovetail Cutters and Dovetail Cutters with Cylindrical Shanks Third Edition
ISO
3860
Bore Cutters with Key Drive - Form Milling Cutters with Constant Profile First Edition
ISO
3861
Rubber Hoses for Sand and Grit Blasting - Specification Third edition
Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 1: Oil-based fluid
ISO
3862-1
applications First Edition
Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types Specification Part 2: Water-based fluid
ISO
3862-2
applications First edition; Cancels and Replaces ISO 3862:1991
ISO
3863
Cylindrical Cork Stoppers - Dimensional Characteristics, Sampling, Packaging and Marking Second Edition
Graphical Symbols - Safety Colours and Safety Signs - Part 1: Design Principles for Safety Signs in Workplaces and Public Areas
ISO
3864-1
First Edition; Corrected Version: 12/15/2003
ISO
3864-2
Graphical symbols Safety colours and safety signs Part 2: Design principles for product safety labels First Edition
Graphical symbols Safety colours and safety signs Part 3: Design principles for graphical symbols for use in safety signs First
ISO
3864-3
Edition
ISO
3865
Rubber, vulcanized or thermoplastic Methods of test for staining in contact with organic material Fourth Edition
Office Machines and Printing Machines Used for Information Processing - Widths of Fabric Printing Ribbons on Spools Exceeding 19
ISO
3866
mm First Edition
ISO
3867
Composition Cork - Expansion Joint Fillers - Test Methods Second Edition
Metallic and Other Non-Organic Coatings - Measurement of Coating Thicknesses - Fizeau Multiple-Beam Interferometry Method First
ISO
3868
Edition; (CEN EN ISO 3868: 1994)
ISO
3869
Composition Cork - Expansion Joint Fillers - Specification, Packaging and Marking Second Edition
Conveyor Belts (Fabric Carcass), with Length Between Pulley Centres up to 300 m, for Loose Bulk Materials - Adjustment of Take-Up
ISO
3870
Device First Edition
ISO
3871
Road Vehicles - Labelling of Containers for Petroleum-Based or Non-Petroleum-Based Brake Fluid Fourth Edition
ISO
3873
Industrial Safety Helmets First Edition
ISO
3874 AMD 4
Series 1 freight containers ù Handling and securing AMENDMENT 4: 45 ft containers First Edition
ISO
3874 AMD 3
Series 1 freight containers ù Handling and securing AMENDMENT 3: Double stack rail car operations First Edition
ISO
3874 AMD 2
Series 1 freight containers ù Handling and securing AMENDMENT 2: Vertical tandem lifting Fifth Edition
Series 1 freight containers ù Handling and securing AMENDMENT 1: Twistlocks, latchlocks, stacking fittings and lashing rod systems
ISO
3874 AMD 1
for securing of containers Fifth Edition; Corrected and Reprinted 09/01/2001
ISO
3874
Series 1 freight containers ù Handling and securing Fifth Edition
ISO
3875
Machine tools Test conditions for external cylindrical centreless grinding machines Testing of the accuracy Third Edition
ISO
3876
Shipbuilding - Inland Vessels - Hand-Holes Second Edition
ISO
3877-1
Tyres, Valves and Tubes - List of Equivalent Terms - Part I: Tyres Second Edition
ISO
3877-2
Tyres, Valves and Tubes - List of Equivalent Terms - Part 2: Tyre Valves Second Edition
ISO
3877-3
Tyres, Valves and Tubes - List of Equivalent Terms - Part III: Tubes First Edition
ISO
3877-4
Tyres, Valves and Tubes - List of Equivalent Terms - Part 4: Solid Tyres First Edition
ISO
3878
Hardmetals - Vickers Hardness Test Second Edition; (CEN EN 23878: 1993)
ISO
3880-1
Building Construction - Stairs - Vocabulary - Part 1: First Edition
ISO
3881
Building Construction - Modular Co-Ordination - Stairs and Stair Openings - Co-Ordinating Dimensions First Edition
ISO
3882
Metallic and Other Inorganic Coatings - Review of Methods of Measurement of Thickness Third Edition
ISO
3883
Office Machines - Line and Character Capacity of Address Masters First Edition
ISO
3887
Steel - Determination of Depth of Decarburization Second Edition
Passenger Cars - Test Track for a Severe Lane-Change Manoeuvre - Part 1: Double Lane-Change First Edition; Cancels and
ISO
3888-1
Replaces TR 3888: 1975
ISO
3888-2
Passenger cars Test track for a severe lane-change manoeuvre Part 2: Obstacle avoidance First Edition
ISO
3889
Milk and milk products Specification of Mojonnier-type fat extraction flasks Second Edition; IDF 219
Milk and Milk Porducts - Determination of Residues of Organochlorine Compounds (Pesticides) - Part 1: General Considerations and
ISO
3890-1
Extraction Methods First Edition
Milk and Milk Porducts - Determination of Residues of Organochlorine Compounds (Pesticides) - Part 2: Test Methods for Crude
ISO
3890-2
Extract Purification and Confirmation First Edition
ISO
3891
Acoustics - Procedure for Describing Aircraft Noise Heard on the Ground First Edition
Conversion Coatings on Metallic Materials - Determination of Coating Mass per Unit Area - Gravimetric Methods Edition; (CEN EN
ISO
3892
ISO 3892: 1994) (PNS 683: 1990) Second Edition
ISO
3893
Concrete - Classification by Compressive Strength First Edition
ISO
3894
Road vehicles Wheels/rims for commercial vehicles Test methods Third Edition
ISO
3895
Road Vehicles - Screened and Waterproof Spark-Plug and Its Connection - Type 2 Third Edition
ISO
3896
Road Vehicles - Screened and Waterproof Spark-Plug and Its Connection - Type 3 Third Edition
ISO
3898
Bases for Design of Structures - Notations - General Symbols Third Edition
ISO
3899
Rubber - Nitrile latex - Determination of residual acrylonitrile content Third Edition
ISO
3900
Rubber - Nitrile Latex - Determination of Bound Acrylonitrile Content Second Edition
ISO
3901
Information and Documentation - International Standard Recording Code (ISRC) Second Edition
ISO
3902
Shipbuilding and Marine Structures - Gaskets for Rectangular Windows and Side Scuttles Second Edition
ISO
3903
Shipbuilding and Marine Structures - Ships Ordinary Rectangular Windows Second Edition
ISO
3904
Shipbuilding and Marine Structures - Clear-View Screens Second Edition
ISO
3907
Hardmetals - Determination of Total Carbon Content - Gravimetric Method Second Edition; (CEN EN 23907: 1993)
ISO
3908
Hardmetals - Determination of Insoluble (Free) Carbon Content - Gravimetric Method Second Edition; (CEN EN 23908: 1993)
ISO
3909
Hardmetals - Determination of Cobalt - Potentiometric Method First Edition; (CEN EN 23909: 1993)
ISO
3910
Rubber Boots, Unlined Moulded Second Edition
Wheels and Rims for Pneumatic Tyres - Vocabulary, Designation and Marking Roues Et Jantes Pour Pneumatiques - Vocabulaire,
ISO
3911
Designation Et Marquage Third Edition
ISO
3912
Woodruff Keys and Keyways First Edition; (NZS/ISO 3912: 1977)
ISO
3913
Shipbuilding - Welded Steel Bollards First Edition: Addendum 1: 1980
ISO
3914-1
Textile Machinery and Accessories - Cylindrical Tubes - Part 1: Recommended Main Dimensions Second Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 2: Dimensions, Tolerances and Designation of Tubes for Open-End
ISO
3914-2
Spinning Machines Second Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 3: Dimensions, Tolerances and Designation of Tubes for Tape Yarns
ISO
3914-3
Second Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 4: Dimensions, Tolerances and Designation of Tubes for Textured Yarns
ISO
3914-4
Second Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 5: Dimensions, Tolerances and Designation of Tubes for Continuous
ISO
3914-5
Spin-Drawn Synthetic Filament Yarns First Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 6: Dimensions, Tolerances and Designation of Tubes for Cross-Wound
ISO
3914-6
Packages in Winding and Twisting First Edition
Textile Machinery and Accessories - Cylindrical Tubes - Part 7: Dimensions, Tolerances and Designation of Perforated Tubes for
ISO
3914-7
Cheese Dyeing First Edition;
ISO
3915
Plastics - Measurement of Resistivity of Conductive Plastics First Edition
Road Vehicles - Safety Glazing Materials - Test Methods for Resistance to Radiation, High Temperature, Humidity, Fire and
ISO
3917
Simulated Weathering Third Edition
ISO
3918
Milking Machine Installations - Vocabulary Installations De Traite Mecanique - Vocabulaire Third Edition
ISO
3919
Coated Abrasives - Flap Wheels with Shafts Fourth edition
ISO
3923-1
Metallic Powders - Determination of Apparent Density - Part 1: Funnel Method Second Edition
ISO
3923-2
Metallic Powders - Determination of Apparent Density - Part 2: Scott Volumeter Method First Edition; (CEN EN 23923-2: 1993)
ISO
3924
Petroleum Products - Determination of Boiling Range Distribution - Gas Chromatography Method Second Edition
ISO
3925
Unsealed Radioactive Substances - Identification and Certification First Edition
ISO
3926
Shipbuilding - Inland Navigation - Couplings for Oil and Fuel Reception - Mating Dimensions Second Edition
ISO
3927
Metallic Powders, Excluding Powders for Hardmetals - Determination of Compressibility in Uniaxial Compression Third Edition
ISO
3928
Sintered Metal Materials, Excluding Hardmetals - Fatigue Test Pieces Second Edition
ISO
3929
Road vehicles Measurement methods for exhaust gas emissions during inspection or maintenance Third edition
ISO
3930
Instruments for Measuring Vehicle Exhaust Emissions Third Edition; OIML R 99; Amendment 1: 10/15/2004
Rubber, Vulcanized and Thermoplastic - Preformed Gaskets Used in Buildings - Classification, Specifications and Test Methods
ISO
3934
Second Edition
ISO
3935
Shipbuilding - Inland Navigation - Fire-Fighting Water System - Pressures First Edition
ISO
3936
Reduction Sleeves with Tenon Drive with External and Internal 7/24 Taper - Dimensions Third Edition
ISO
3937
Cutter Arbors with Tenon Drive - Dimensions Third Edition
ISO
3938
Hydraulic Fluid Power - Contamination Analysis - Method for Reporting Analysis Data First Edition
ISO
3939
Fluid Power Systems and Components - Multiple Lip Packing Sets - Methods for Measuring Stack Heights First Edition
ISO
3940
Tapered Die-Sinking Cutters with Parallel Shanks First Edition
ISO
3941
Classification of Fires Second Edition
ISO
3943
Photography - Processing Chemicals - Specifications for Anhydrous Sodium Acetate Second Edition
ISO
3944
Fertilizers - Determination of Bulk Density (Loose) Third Edition; (CEN EN 1236: 1995)
Starches and Derived Products - Determination of Total Phosphorous Content - Spectrophotometric Method First Edition; (CENELEC
ISO
3946
EN ISO 3946 - 1994)
ISO
3947
Starches, Native or Modified - Determination of Total Fat Content First Edition; (CENELEC EN ISO 3947 - 1994)
ISO
3948
Shipbuilding - Inland Vessels - Compressed-Air Systems - Pressure Ranges First Edition
ISO
3949
Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification Third Edition
ISO
3950
Dentistry - Designation System for Teeth and Areas of the Oral Cavity Second Edition; (Corrected and Reprinted - 1995)
Sampling procedures for inspection by variables Part 1: Specification for single sampling plans indexed by acceptance quality limit
ISO
3951-1
(AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL First edition; Cancels and Replaces ISO 3951:1989
Sampling procedures for inspection by variables Part 2: General specification for single sampling plans indexed by acceptance
ISO
3951-2
quality limit (AQL) for lot-by-lot inspection of independent quality characteristics First edition; Cancels and Replaces ISO 3951:1989
Sampling procedures for inspection by variables ù Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-
ISO
3951-3
by-lot inspection First Edition
Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for
ISO
3951-5
inspection by variables (known standard deviation) First Edition;
ISO
3952-1
Kinematic Diagrams - Graphical Symbols - Part 1 First Edition; Amendment 1: 10/15/2002
ISO
3952-2
Kinematic Diagrams - Graphical Symbols - Part 2 First Edition
ISO
3952-3
Kinematic Diagrams - Graphical Symbols - Part 3 First Edition; (CEN EN ISO 3952-3: 1994)
ISO
3952-4
Kinematic Diagrams - Graphical Symbols - Part 4 First Edition
ISO
3953
Metallic Powders - Determination of Tap Density Third Edition; (CEN EN ISO 3953: 1995)
ISO
3954
Powders for Powder Metallurgical Purposes - Sampling Second Edition
ISO
3958
Passenger Cars - Driver Hand-Control Reach Second Edition
ISO
3959
Green Bananas - Ripening Conditions First Edition
ISO
3960
Animal and vegetable fats and oils ù Determination of peroxide value ù Iodometric (visual) endpoint determination Fourth Edition
ISO
3961
Animal and Vegetable Fats and Oils - Determination of Iodine Value Third Edition
ISO
3963
Fertilizers - Sampling from a Conveyor by Stopping the Belt First Edition
ISO
3964
Dental Handpieces - Coupling Dimensions Second Edition; (CAN/CSA-Z349.29-M92)
ISO
3965
Agricultural Wheeled Tractors - Maximum Speeds - Method of Determination Second Edition
Hydraulic Fluid Power - Filters - Evaluation of Differential Pressure Versus Flow Characteristics Second Edition; Technical
ISO
3968
Corrigendum 1: 9/01/2002; Supersedes (NFPA) B93.80M
ISO
3969
Shipbuilding - Inland Vessels - Operational Documentation First Edition
ISO
3970
Modular Units for Machine Tool Construction - Integral Way Columns - Floor-Mounted Type First Edition; Amendment 1: 1982
ISO
3972
Sensory Analysis - Methodology - Method of Investigating Sensitivity of Taste Second Edition
ISO
3974
Definitions of Living Animals for Slaughter - Ovines First Edition
ISO
3975
Definitions of Living Animals for Slaughter - Horses First Edition
ISO
3976
Milk fat Determination of peroxide value Second Edition
ISO
3977-1
Gas Turbines - Procurement - Part 1: General Introduction and Definitions First Edition; Replaces ISO 3977:1991
ISO
3977-2
Gas Turbines - Procurement - Part 2: Standard Reference Conditions and Ratings First Edition; Replaces ISO 3977:1991
ISO
3977-3
Gas Turbines - Procurement - Part 3: Design Requirements Second Edition
ISO
3977-4
Gas Turbines - Procurement - Part 4: Fuels and Environment First Edition
ISO
3977-5
Gas Turbines - Procurement - Part 5: Applications for Petroleum and Natural Gas Industries First Edition
ISO
3977-7
Gas Turbines - Procurement - Part 7: Technical Information First Edition
ISO
3977-8
Gas Turbines - Procurement - Part 8: Inspection, Testing, Installation and Commissioning First Edition
ISO
3977-9
Gas Turbines - Procurement - Part 9: Reliability, Availability, Maintainability and Safety First Edition
Aluminium and Aluminium Alloys - Determination of Chromium - Spectrophotometric Method Using Diphenylcarbazide, After
ISO
3978
Extraction First Edition
ISO
3979
Aluminium and Aluminium Alloys - Determination of Nickel - Spectrophotometric Method Using Dimethylglyoxime First Edition
ISO
3980
Aluminium and Aluminium Alloys - Determination of Copper - Atomic Absorption Spectrophotometric Method First Edition
ISO
3981
Aluminium and Aluminium Alloys - Determination of Nickel - Atomic Absorption Spectrophotometric Method First Edition
ISO
3984
Road vehicles Rear moving barrier impact test procedure Third Edition
ISO
3987
Petroleum Products - Lubricating Oils and Additives - Determination of Sulphated Ash Second Edition
Liquefied Petroleum Gas and Light Hydrocarbons - Determination of Density or Relative Density - Pressure Hydrometer Method First
ISO
3993
Edition; (CEN EN ISO 3993: 1995)
Plastics Hoses - Helical-Thermoplastic-Reinforced Thermoplastics Hoses for Suction and Discharge of Aqueous Materials -
ISO
3994
Specification Third Edition
Metallic Powders - Determination of Green Strength by Transverse Rupture of Rectangular Compacts Second Edition; (CEN EN
ISO
3995
23995: 1993)
ISO
3996
Road Vehicles - Brake Hose Assemblies for Hydraulic Braking Systems Used with a Non-Petroleum-Base Brake Fluid Third Edition
ISO
3998
Textiles - Determination of Resistance to Certain Insect Pests First Edition
Radiation protection Apparatus for industrial gamma radiography Specifications for performance, design and tests Second Edition;
ISO
3999
Supersedes ISO 3999-1: 2000
ISO
4000-1
Passenger Car Tyres and Rims - Part 1: Tyres (Metric Series) Eighth Edition
ISO
4000-2
Passenger car tyres and rims ù Part 2: Rims Fourth Edition
ISO
4001
Shipbuilding - Inland Navigation - Raft-Type Life-Saving Apparatus First Edition
ISO
4002-1
Equipment for Sowing and Planting - Disks - Part I: Concave Disks Type D1 - Dimensions First Edition
ISO
4002-2
Equipment for Sowing and Planting - Disks - Part II: Flat Disks Type D2 with Single Bevel - Dimensions First Edition
ISO
4003
Permeable Sintered Metal Materials - Determination of Bubble Test Pore Size First Edition; (CEN EN 24003: 1993)
ISO
4004
Agricultural Tractors and Machinery - Track Widths First Edition
ISO
4006
Measurement of Fluid Flow in Closed Conduits - Vocabulary and Symbols Second Edition; (CEN EN 24006: 1993)
ISO
4007
Personal Eye-Protectors - Vocabulary First Edition
ISO
4008-1
Road Vehicles - Fuel Injection Pump Testing - Part 1: Dynamic Conditions Second Edition; (Erratum-1982)
ISO
4008-2
Road Vehicles - Fuel Injection Pump Testing - Part 2: Static Conditions First Edition
ISO
4008-3
Road Vehicles - Fuel Injection Pump Testing - Part 3: Application and Test Procedures First Edition; Amendment 1: 10/01/2002
ISO
4009
Commercial Vehicles - Location of Electrical and Pneumatic Connections between Towing Vehicles and Trailers Third Edition
ISO
4010
Diesel Engines - Calibrating Nozzle, Delay Pintle Type Second Edition
ISO
4014
Hexagon Head Bolts - Product Grades A and B Third Edition
ISO
4015
Hexagon Head Bolts - Product Grade B - Reduced Shank (Shank Diameter is Approximately Equal to Pitch Diameter) First Edition
ISO
4016
Hexagon Head Bolts - Product Grade C Third Edition
ISO
4017
Hexagon Head Screws - Product Grades A and B Third Edition
ISO
4018
Hexagon Head Screws - Product Grade C Third Edition
ISO
4019
Structural Steels - Cold-Formed, Welded, Structural Hollow Sections - Dimensions and Sectional Properties Second Edition
ISO
4020
Road Vehicles - Fuel Filters for Diesel Engines - Test Methods First Edition; Replaces ISO 4020-1
Hydraulic Fluid Power - Particulate Contamination Analysis - Extraction of Fluid Samples from Lines of an Operating System Second
ISO
4021
Edition
ISO
4022
Permeable Sintered Metal Materials - Determination of Fluid Permeability Second Edition
ISO
4023
Rubber Hoses for Steam - Test Methods Third Edition (CEN EN ISO 4023:1995)
ISO
4024
Road Vehicles - Ignition Coils - Low-Tension Cable Connections Second Edition
ISO
4026
Hexagon socket set screws with flat point Third Edition
ISO
4027
Hexagon Socket Set Screws with Cone Point Third Edition
ISO
4028
Hexagon Socket Set Screws with Dog Point Third Edition
ISO
4029
Hexagon socket set screws with cup point Third Edition
ISO
4030
Road Vehicles - Vehicle Identification Number (VIN) - Location and Attachment Second Edition
ISO
4032
Hexagon Nuts, Style 1 - Product Grades A and B Third Edition; Corrected and Reprinted: 03/01/2001
ISO
4033
Hexagon Nuts, Style 2 - Product Grades A and B Second Edition
ISO
4034
Hexagon Nuts - Product Grade C Third Edition
ISO
4035
Hexagon Thin Nuts (Chamfered) - Product Grades A and B Third Edition
ISO
4036
Hexagon Thin Nuts (Unchamfered) - Product Grade B Second Edition; Corrected and Reprinted 12-1-2000
X and Gamma Reference Radiation for Calibrating Dosemeters and Doserate Meters and for Determining Their Response as a
ISO
4037-1
Function of Photon Energy - Part 1: Radiation Characteristics and Production Methods First Edition
X and Gamma Reference Radiation for Calibrating Dosemeters and Doserate Meters and for Determining Their Response as a
Function of Photon Energy - Part 2: Dosimetry for Radiation Protection over the Energy Ranges 8 keV to 1,3 MeV and 4 MeV to 9
ISO
4037-2
MeV First Edition
X and Gamma Reference Radiation for Calibrating Dosemeters and Doserate Meters and for Determining Their Response as a
Function of Photon Energy - Part 3: Calibration of Area and Personal Dosemeters and the Measurement of Their Response as a
ISO
4037-3
Function of Energy and Angle of Incidence First Edition
X and Gamma Reference Radiation for Calibrating Dosemeters and Doserate Meters and for Determining Their Response as a
Function of Photon Energy - Part 4: Calibration of area and personal dosemeters in low energy X reference radiation fields First
ISO
4037-4
Edition
ISO
4038
Road Vehicles - Hydraulic Braking Systems - Simple Flare Pipes, Tapped Holes, Male Fittings and Hose End Fittings Third Edition
ISO
4039-1
Road Vehicles - Pneumatic Braking Systems - Part 1: Pipes, Male Fittings and Tapped Holes with Facial Sealing Surface First Edition
Road Vehicles - Pneumatic Braking Systems - Part 2: Pipes, Male Fittings and Tapped Holes with Conical Sealing Surface First
ISO
4039-2
Edition
ISO
4040
Road Vehicles - Location of Hand Controls, Indicators and Tell-Tales in Motor Vehicles Fourth Edition
ISO
4042
Fasteners - Electroplated Coatings Second Edition
ISO
4043
Mobile Booths for Simultaneous Interpretation - General Characteristics and Equipment Second Edition
ISO
4044
Leather - Preparation of Chemical Test Samples First Edition
ISO
4045
Leather - Determination of pH First Edition
Paper, Board, Pulps and Related Terms - Vocabulary - Part 1: Alphabetical Index Papier, Carton, Pates et Termes Connexes -
ISO
4046-1
Vocabulaire - Partie 1: Index Alphabetique First Edition
Paper, Board, Pulps and Related Terms - Vocabulary - Part 2: Pulping Terminology Papier, Carton, Pates et Termes Connexes -
ISO
4046-2
Vocabulaire - Partie 2: Terminologie de la Fabrication de la Pate First Edition
Paper, Board, Pulps and Related Terms - Vocabulary - Part 3: Paper-Making Terminology Papier, Carton, Pates et Termes
ISO
4046-3
Connexes - Vocabulaire - Partie 3: Terminologie de la Fabrication du Papier First Edition
Paper, Board, Pulps and Related Terms - Vocabulary - Part 4: Paper and Board Grades and Converted Products Papier, Carton,
Pates Et Termes Connexes - Vocabulaire - Partie 4: Categories Et Produits Transformes De Papier Et De Carton First Edition;
ISO
4046-4
Together with ISO 4046-1, ISO 4046-2, ISO 4046-3 and ISO 4046-5, cancel and replaces ISO 4046: 1978
Paper, Board, Pulps and Related Terms - Vocabulary - Part 5: Properties of Pulp, Paper and Board Papier, Carton, Pates et Termes
Connexes - Vocabulaire - Partie 5: Proprietes De La Pate, Du Papier Et Due Carton First Edition; Together with ISO 4046-1, ISO
ISO
4046-5
4046-2, ISO 4046-3 and ISO 4046-4, cancel and replace ISO 4046: 1978
ISO
4047
Leather - Determination Sulphated Total Ash and Sulphated Water-Insoluble Ash First Edition
ISO
4048
Leather - Determination of Matter Soluble in Dichloromethane First Edition
ISO
4049
Dentistry - Polymer-Based Filling, Restorative and Luting Materials Third Edition
ISO
4050
Shipbuilding - Inland Vessels -Rhine" and Hall s Stockless Anchors First Edition"
ISO
4051
Shipbuilding - Inland Vessels - Steering Gear - Values of Torques First Edition
ISO
4052
Coffee - Determination of Caffeine Content (Reference Method) First Edition
Information Processing - Data Interchange on 6,30 mm (0.25 in) Magnetic Tape Cartridge, 63 bpmm (1 600 bpi) Phase-Encoded
ISO
4057
Second Edition
ISO
4058
Magnesium and Its Alloys - Determination of Nickel - Photometric Method Using Dimethylglyoxime First Edition
ISO
4059
Polyethylene (PE) Pipes - Pressure Drop in Mechanical Pipe-Jointing Systems - Method of Test and Requirements First Edition
ISO
4063
Welding and Allied Processes - Nomenclature of Processes and Reference Numbers Third Edition
Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 1: Specifications
ISO
4064-1
Third Edition; Replaces ISO 7858-1:1998 and ISO 10385-1:2000
Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation
ISO
4064-2
requirements Third Edition; Replaces ISO 7858-2:2000
Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 3: Test methods and
ISO
4064-3
equipment Third Edition; Replaces ISO 7858-3:1992
ISO
4065
Thermoplastic Pipes - Universal Wall Thickness Table Second Edition
ISO
4067-2
Building and Civil Engineering Drawings - Installations - Part 2: Simplified Representation of Sanitary Appliances First Edition
ISO
4072
Green Coffee in Bags - Sampling First Edition
Dental Equipment - Items of Dental Equipment at the Working Place - Identification System First Edition; (Corrected and Reprinted -
ISO
4073
1981) (CAN/CSA-Z349.30-M92)
ISO
4074 CORR 1
Natural latex rubber condoms ù Requirements and test methods First Edition
ISO
4074
Natural latex rubber condoms ù Requirements and test methods First Edition
Rubber Hoses and Hose Assemblies - Textile-Reinforced Hydraulic Types - Specification - Part 1: Oil-Based Fluid Applications First
ISO
4079-1
Edition
Rubber hoses and hose assemblies Textile-reinforced hydraulic types Specification Part 2: Water-based fluid applications First
ISO
4079-2
Edition
Rubber and Plastics Hoses and Hose Assemblies - Determination of Permeability to Gas Third Edition; Corrigendum 1-1997;
ISO
4080
Corrigendum 2-1998
ISO
4081
Rubber hoses and tubing for cooling systems for internal-combustion engines Specification Second Edition
ISO
4082
Road Vehicles - Motor Vehicles - Flasher Units First Edition
ISO
4084
Aircraft - Repairable Contactors (Not Hermetically Sealed) - Performance Requirements First Edition
ISO
4085
Shipbuilding - Inland Navigation - Swing Derricks First Edition
ISO
4086
Road Vehicles - 90 Semi-Trailer Fifth Wheel Kingpin - Interchangeability Third Edition
ISO
4087
Micrographics Microfilming of newspapers for archival purposes on 35 mm microfilm Third Edition
ISO
4089
Shipbuilding - Inland Navigation - Sealing Rubber for Covers of Cargo Hatches First Edition
Photography - Medical Radiographic Cassettes/Screens/Films and Hard-copy Imaging Films - Dimensions and Specifications Third
ISO
4090
Edition
ISO
4091
Road Vehicles - Connectors for the Electrical Connection of towing and towed vehicles, tests and requirements Third Edition
ISO
4093
Diesel Engines - Fuel Injection Pumps - High-Pressure Pipes for Testing Third Edition
Paper, board and pulps - International calibration of testing apparatus - Nomination and acceptance of standardizing and authorized
ISO
4094
laboratories Second edition
ISO
4095
Aerospace - Bihexagonal Drives - Wrenching Configuration - Metric Series Second Edition
ISO
4097
Rubber, Ethylene-Propylene-Diene (EPDM) - Evaluation Procedure Fifth Edition
Leather Chemical tests Determination of water-soluble matter, water-soluble inorganic matter and watersoluble organic matter First
ISO
4098
Edition; IULTCS/IUC 6
ISO
4100
Road Vehicles - World Parts Manufacturer Identifier (WPMI) Code First Edition
ISO
4101
Drawn Steel Wire for Elevator Ropes - Specifications First Edition
ISO
4102
Equipment for Crop Protection - Sprayers - Connection Threading First Edition
ISO
4103
Concrete - Classification of Consistency First Edition
ISO
4105
Textile Machinery and Accessories - Wires for Flexible Card Clothings First Edition
ISO
4106
Motorcycles - Engine Test Code - Net Power Third Edition
ISO
4107
Commercial Vehicles - Wheel Hub Attachment Dimensions Third Edition
ISO
4112
Cereals and Pulses - Guidance on Measurement of the Temperature of Grain Stored in Bulk Second Edition
ISO
4113
Road Vehicles - Calibration Fluid for Diesel Injection Equipment Second Edition
ISO
4115
Air Cargo Equipment - Air/Land Pallet Nets Third Edition
ISO
4116
Air Cargo Equipment - Ground Equipment Requirements for Compatibility with Aircraft Unit Load Devices Second Edition
ISO
4117
Air and Air/Land Cargo Pallets - Specification and Testing Second Edition
ISO
4118
Air cargo Non-certified containers for the lower deck of large-capacity aircraft Specification and testing Third Edition
ISO
4119
Pulps - Determination of Stock Concentration Second Edition (CEN EN ISO 4119: 1996)
ISO
4120
Sensory analysis Methodology Triangle test Second Edition
ISO
4121
Sensory analysis Guidelines for the use of quantitative response scales Second Edition
ISO
4123
Belt Conveyors - Impact Rings for Carrying Idlers and Discs for Return Idlers - Main Dimensions First Edition;
ISO
4124
Liquid Hydrocarbons - Dynamic Measurement - Statistical Control of Volumetric Metering Systems First Edition
ISO
4125
Dry Fruits and Dried Fruits - Definitions and Nomenclature Second Edition
ISO
4126-1
Safety devices for protection against excessive pressure Part 1: Safety valves Second Edition
ISO
4126-2
Safety Devices for Protection Against Excessive Pressure - Part 2: Bursting Disc Safety Devices First Edition
Safety devices for protection against excessive pressure Part 3: Safety valves and bursting disc safety devices in combination First
ISO
4126-3
Edition;:1991 [Replaced: ISO 6718]
ISO
4126-4
Safety devices for protection against excessive pressure Part 4: Pilot-operated safety valves First Edition; Replaces ISO 6718:1991
Safety devices for protection against excessive pressure ù Part 5: Controlled safety pressure relief systems (CSPRS) TECHNICAL
ISO
4126-5 CORR 2
CORRIGENDUM 1 First Edition
Safety devices for protection against excessive pressure ù Part 5: Controlled safety pressure relief systems (CSPRS) TECHNICAL
ISO
4126-5 CORR 1
CORRIGENDUM 1 First Edition
ISO
4126-5
Safety devices for protection against excessive pressure ù Part 5: Controlled safety pressure relief systems (CSPRS) First Edition
Safety devices for protection against excessive pressure Part 6: Application, selection and installation of bursting disc safety devices
ISO
4126-6
First Edition
ISO
4126-7 CORR 1
Safety devices for protection against excessive pressure ù Part 7: Common data TECHNICAL CORRIGENDUM 1 First Edition
ISO
4126-7
Safety devices for protection against excessive pressure ù Part 7: Common data First Edition
ISO
4127-1
Shipbuilding - Inland Navigation - Fairleads - Part 1: Two-Lip Fairleads First Edition
ISO
4127-2
Shipbuilding - Inland Vessels - Fairleads - Part 2: Roller Fairleads First Edition
ISO
4128
Aircraft - Air Mode Modular Containers First Edition
ISO
4129
Mopeds - Symbols for Controls, Indicators and Tell-Tales Second Edition
ISO
4130
Road Vehicles - Three-Dimensional Reference System and Fiducial Marks - Definitions First Edition
ISO
4131
Road Vehicles - Dimensional Codes for Passenger Cars First Edition;
Unplasticized Polyvinyl Chloride (PVC) and Metal Adaptor Fittings for Pipes Under Pressure - Laying Lengths and Size of Threads -
ISO
4132
Metric Series First Edition
ISO
4134
Meat and Meat Products - Determination of L-(+)- Glutamic Acid Content - Reference Method Second Edition
Anaesthetic and Respiratory Equipment - Vocabulary Materiel D'Anesthesie Et De Reanimation Respiratoire - Vocabulaire Third
ISO
4135
Edition
ISO
4136
Destructive Tests on Welds in Metallic Materials - Transverse Tensile Test Second Edition
ISO
4138
Passenger cars Steady-state circular driving behaviour Open-loop test methods Third Edition
ISO
4139
Ferrosilicon - Determination of Aluminium Content - Flame Atomic Absorption Spectrometric Method First Edition
ISO
4140
Ferrochromium and Ferrosilicochromium - Determination of Chromium Content - Potentiometric Method First Edition
Road vehicles - Multi-core connecting cables - Part 1: Test methods and requirements for basic performance sheathed cables
ISO
4141-1
Second Edition
Road vehicles Multi-core connecting cables Part 2: Test methods and requirements for high performance sheathed cables Second
ISO
4141-2
Edition
Road Vehicles - Multicore Connecting Cables - Part 3: Construction Dimensions and Marking of Unscreened Sheathed Low-Voltage
ISO
4141-3
Cables Second Edition
Road Vehicles - Multi-core Connecting Cables - Part 4: Articulation Test Method and Requirements for Coiled Cable Assemblies First
ISO
4141-4
Edition
ISO
4142
Laboratory Glassware - Test Tubes Second Edition
ISO
4143
Shipbuilding - Inland Vessels - Open Rowing Lifeboats First Edition
ISO
4144
Pipework - Stainless Steel Fittings Threaded in Accordance with ISO 7-1 Second Edition
ISO
4145
Non-Alloy Steel Fittings Threaded to ISO 7/1 Second Edition
Aerospace - Nuts, Hexagonal, Slotted (Castellated), Nrml Ht, Nrml Across Flats, with MJ Threads, Cls: 600MPa (at Ambt T)/120 Dgs
C, 600MPa (at Ambt T)/235 Dgs. C, 900MPa (at Ambt T)/425 Dgs. C, 1100 MPa (at Ambt T)/235 Dgs. C, 1100 MPa (at Ambt T)/315
Dgs. C, 1100MPa (at Ambt T)/650 Dgs. C, 1210MPa (at Ambt T)/730 Dgs. C, 1250MPa (at Ambt T)/235 Dgs. C and 1550MPa (at
ISO
4147
Ambt T)/600 Dgs C - Dims. Third Edition
ISO
4148
Road Vehicles - Special Warning Lamps - Dimensions Fourth Edition
ISO
4149
Green Coffee - Olfactory and visual examination and determination of foreign matter and defects Second edition
ISO
4150
Green Coffee - Size Analysis - Manual Sieving Second Edition
ISO
4151
Road Vehicles - Mopeds - Type, Location and Functions of Controls Second Edition
ISO
4153
Aircraft - Pressure Fuel Dispensing System - Test Procedure and Limit Value for Shut-Off Surge Pressure First Edition
Straight cylindrical involute splines - Metric module, side fit - Part 1: Generalities First Edition; Together with ISO 4156-2 and ISO
ISO
4156-1
4156-3 Replaces ISO 4156
Straight cylindrical involute splines - Metric module, side fit - Part 2: Dimensions First Edition; Together with ISO 4156-1 and ISO
ISO
4156-2
4156-3 Replaces ISO 4156
Straight cylindrical involute splines - Metric module, side fit - Part 3: Inspection First Edition; Together with ISO 4156-1 and ISO 4156-
ISO
4156-3
2 Replaces ISO 4156
ISO
4157-1
Construction Drawings - Designation Systems - Part 1: Buildings and Parts of Buildings Second Edition
ISO
4157-2
Construction Drawings - Designation Systems - Part 2: Room Names and Numbers Second Edition
ISO
4157-3
Construction Drawings - Designation Systems - Part 3: Room Identifiers First Edition
ISO
4158
Ferrosilicon, Ferrosilicomanganese and Ferrosilicochromium - Determination of Silicon Content - Gravimetric Method First Edition
ISO
4159
Ferromanganese and Ferrosilicomanganese - Determination of Manganese Content - Potentiometric Method First Edition
ISO
4161
Hexagon Nuts with Flange - Coarse Thread Second Edition
ISO
4162
Hexagon Flange Bolts - Small Series First Edition
ISO
4164
Road Vehicles - Mopeds - Engine Test Code - Net Power First Edition
ISO
4165
Road Vehicles - Electrical Connections - Double-Pole Connection Second Edition
ISO
4167
Polyolefin agricultural twines Second Edition
ISO
4168
Timekeeping Instruments - Conditions for Carrying out Checks on Radioluminescent Deposits Second Edition
ISO
4170
Air Cargo Equipment - Interline Pallet Nets Third Edition
ISO
4171
Air Cargo Equipment - Interline Pallets Second Edition
ISO
4172
Technical Drawings - Construction Drawings - Drawings for the Assembly of Prefabricated Structures Second Edition
ISO
4173
Ferromolybdenum - Determination of Molybdenum Content - Gravimetric Method First Edition
ISO
4174
Cereals, Oilseeds and Pulses - Measurement of Unit Pressure Loss in One-Dimensional Air Flow Through Bulk Grain Second Edition
ISO
4175
Shipbuilding - Shipborne Barges, Series 1 - Main Dimensions First Edition
ISO
4176
Fertilizers - Determination of Nitrate Nitrogen Content - Nitron Gravimetric Method First Edition
ISO
4178
Complete, Filled Transport Packages - Distribution Trials - Information to Be Recorded First Edition; (CEN EN 24178: 1992)
ISO
4179
Ductile iron pipes and fittings for pressure and non-pressure pipelines Cement mortar lining Third Edition
Complete, Filled Transport Packages - General Rules for the Compilation of Performance Test Schedules - Part 1: General Principles
ISO
4180-1
First Edition; (CEN EN 24180-1: 1992)
Complete, Filled Transport Packages - General Rules for the Compilation of Performance Test Schedules - Part 2: Quantitative Data
ISO
4180-2
First Edition; (CEN EN 24180-2: 1992)
ISO
4182
Motor Vehicles - Measurement of Variations in Dipped-Beam Headlamp Angle as a Function of Load Third Edition
ISO
4183
Belt Drives - Classical and Narrow V-Belts - Grooved Pulleys (System Based on Datum Width) Third Edition
ISO
4184
Belt Drives - Classical and Narrow V-Belts - Lengths in Datum System Second Edition; (Corrected and Reprinted - 1993)
Measurement of Liquid Flow in Closed Conduits - Weighing Method (CEN EN 24185: 1993) First Edition; Technical Corrigendum 1:
ISO
4185
1993
ISO
4186
Asparagus - Guide to Storage First Edition
ISO
4187
Horse-Radish - Guide to Storage First Edition
ISO
4190-1
Lift (US: Elevator) Installation - Part 1: Class I, II, III and VI Lifts Third Edition; Corrected and Reprinted: 03/01/2001
ISO
4190-2
Lift (US: Elevator) Installation - Part 2: Class IV Lifts Second Edition
ISO
4190-3
Passenger Lift Installations - Part 3: Service Lifts Class V First Edition
ISO
4190-5
Lift (Elevator) installation Part 5: Control devices, signals and additional fittings Third Edition
Lifts and Service Lifts (USA: Elevators and Dumbwaiters) - Part 6: Passenger Lifts to Be Installed in Residential Buildings - Planning
ISO
4190-6
and Selection First Edition
ISO
4192
Aluminium and Aluminium Alloys - Determination of Lead Content - Flame Atomic Absorption Spectrometric Method First Edition
Aluminium and Aluminium Alloys - Determination of Chromium Content - Flame Atomic Absorption Spectrometric Method First
ISO
4193
Edition
ISO
4194
Magnesium Alloys - Determination of Zinc Content - Flame Atomic Absorption Spectrometric Method First Edition
Conveyor belts with heat-resistant rubber covers ù Heat resistance of covers ù Requirements and test methods First edition
ISO
4195
[Replaced: ISO 4195-1, ISO 4195-2]
ISO
4197
Equipment for Working the Soil - Hoe Blades - Fixing Dimensions Second Edition
ISO
4198
Surface Active Agents - Detergents for Hand Dishwashing - Guide for Comparative Testing of Performance First Edition
Plain End Steel Tubes, Welded and Seamless - General Tables of Dimensions and Masses per Unit Length Fourth Edition; Replaces
ISO
4200
ISO 134: 1973 and ISO 336: 1976
ISO
4202
Reduction Sleeves with External 7/24 Taper for Tools with Morse Taper Shanks Second Edition
ISO
4203
Parallel Shank Tools - Driving Tenons and Sockets - Dimensions First Edition
ISO
4204
Countersinks, 90 Degrees, with Morse Taper Shanks and Detachable Pilots First Edition
ISO
4205
Countersinks, 90 Degrees, with Parallel Shanks and Solid Pilots Second Edition; (BS 328: Part 6: 1992) (NZS/BS 328: Pt 6: 1992)
ISO
4206
Counterbores with Parallel Shanks and Solid Pilots Second Edition (BS 328: Part 7: 1992) (NZS/BS 328: Pt 7: 1992)
ISO
4207
Counterbores with Morse Taper Shanks and Detachable Pilots First Edition
ISO
4208
Detachable Pilots for Use with Counterbores and 90 Degrees Countersinks - Dimensions First Edition
ISO
4209-1
Truck and bus tyres and rims (metric series) Part 1: Tyres Sixth Edition
ISO
4209-2
Truck and Bus Tyres and Rims (Metric Series) - Part 2: Rims Third Edition
ISO
4210
Cycles - Safety Requirements for Bicycles Fourth Edition
ISO
4211
Furniture - Assessment of Surface Resistance to Cold Liquids First Edition
ISO
4211-2
Furniture - Tests for Surfaces - Part 2: Assessment of Resistance to Wet Heat First Edition
ISO
4211-3
Furniture - Tests for Surfaces - Part 3: Assessment of Resistance to Dry Heat First Edition
ISO
4211-4
Furniture - Tests for Surfaces - Part 4: Assessment of Resistance to Impact First Edition
Codes for the representation of currencies and funds Codes pour la reprÚsentation des monnaies et types de fonds Sixth Edition;
ISO
4217
Technical Corrigendum: 11/01/2004
Ambient Air - Determination of a Gaseous Acid Air Pollution Index - Titrimetric Method with Indicator or Potentiometric End-Point
ISO
4220
Detection First Edition; (Corrected and Reprinted - 1984)
ISO
4221
Air Quality - Determination of Mass Concentration of Sulphur Dioxide in Ambient Air - Thorin Spectrophotometric Method First Edition
ISO
4223-1
Definitions of Some Terms Used in the Tyre Industry - Part 1: Pneumatic Tyres Fourth Edition
ISO
4223-2
Definitions of Some Terms Used in the Tyre Industry - Part 2: Solid Tyres Second Edition
ISO
4224
Ambient Air - Determination of Carbon Monoxide - Non-Dispersive Infrared Spectrometry Method First Edition
ISO
4225
Air Quality - General Aspects - Vocabulary Second Edition
ISO
4226
Air Quality - General Aspects - Units of Measurement Second Edition
ISO
4228
Spanners and Wrenches - Spline Drive Ends for Power Socket Wrenches First Edition
ISO
4229
Assembly Tools for Screws and Nuts - Single-Head Engineer s Wrenches - Gaps from 50 to 120 mm First Edition
ISO
4230
Hand- and Machine-Operated Circular Screwing Dies for Taper Pipe Threads - R Series Second Edition
ISO
4231
Hand- and Machine-Operated Circular Screwing Dies for Parallel Pipe Threads - G Series Second Edition
ISO
4232-1
Office Machines - Minimum Information to Be Included in Specification Sheets - Part 1: Duplicators First Edition; Erratum-1980
ISO
4232-2
Office Machines - Minimum Information to Be Included in Specifications Sheets - Part 2: Document Copying Machines First Edition
ISO
4232-3
Office Machines - Minimum Information to Be Included in Specification Sheets - Part 3: Postal Franking Machines First Edition
ISO
4238
Cinematography - Optical Printing Ratios for Enlargement and Reduction of Motion-Picture Film Images - Specifications First Edition
ISO
4241
Cinematography - Theatre Projection Leader, Trailer and Cue Marks - Specifications Third Edition
Cinematography - Recording Head Gaps for Two Sound Records on 16 mm Magnetic Film - Positions and Width Dimensions First
ISO
4242
Edition
Cinematography - Picture Image Area and Photographic Sound Record on 16 mm Motion- Picture Release Prints - Positions and
ISO
4243
Dimensions First Edition
ISO
4246
Cinematography - Vocabulary Second Edition
ISO
4247
Jig Bushes and Accessories for Drilling Purposes - Dimensions First Edition
ISO
4248
Jig Bushes - Definitions and Nomenclature First Edition
ISO
4249-1
Motorcycle Tyres and Rims (Code Designated Series) - Part 1: Tyres Second Edition
ISO
4249-2
Motorcycle Tyres and Rims (Code-Designated Series) - Part 2: Tyre Load Ratings Second Edition
ISO
4249-3
Motorcycle Tyres and Rims (Code-Designated Series) - Part 3: Rims Fifth Edition
ISO
4250-1
Earth-mover tyres and rims Part 1: Tyre designation and dimensions Fourth Edition
ISO
4250-2
Earth-mover tyres and rims Part 2: Loads and inflation pressures Fourth Edition
ISO
4250-3
Earth-mover tyres and rims Part 3: Rims Third Edition
Tyres (ply rating marked series) and rims for agricultural tractors and machines - Part 1: Tyre designation and dimensions, and
ISO
4251-1
approved rim contours Sixth Edition
ISO
4251-2
Tyres (ply rating marked series) and rims for agricultural tractors and machines - Part 2: Tyre load ratings Sixth Edition
ISO
4251-3
Tyres (Ply Rating Marked Series) and Rims for Agricultural Tractors and Machines - Part 3: Rims Fourth Edition
Tyres (Ply Rating Marked Series) and Rims for Agricultural Tractors and Machines - Part 4: Tyre Classification and Nomenclature
ISO
4251-4
Second Edition
Tyres (Ply Rating Marked Series) and Rims for Agricultural Tractors and Machines - Part 5: Log Skidder Tyres Second Edition;
ISO
4251-5
Amendment 1-1998
ISO
4252
Agricultural Tractors - Operator s Workplace, Access and Exit - Dimensions Second Edition
ISO
4253
Agricultural Tractors - Operator s Seating Accommodation - Dimensions Second Edition
ISO
4254-1
Agricultural machinery Safety Part 1: General requirements Third Edition
ISO
4254-3
Tractors and Machinery for Agriculture and Forestry - Technical Means for Ensuring Safety - Part 3: Tractors First Edition
Tractors and Machinery for Agriculture and Forestry - Technical Means for Ensuring Safety - Part 5: Power-Driven Soil-Working
ISO
4254-5
Equipment First Edition
Tractors and Machinery for Agriculture and Forestry - Technical Means for Ensuring Safety - Part 6: Equipment for Crop Protection
ISO
4254-6
First Edition; (Corrected and Reprinted - 1996)
Tractors and Machinery for Agriculture and Forestry - Technical Means for Ensuring Safety - Part 7: Combine Harvesters, Forage and
ISO
4254-7
Cotton Harvesters First Edition
Tractors and Machinery for Agriculture and Forestry - Technical Means for Ensuring Safety - Part 9: Equipment for Sowing, Planting
ISO
4254-9
and Distributing Fertilizers First Edition
ISO
4256
Liquefied Petroleum Gases - Determination of Gauge Vapour Pressure - LPG Method Second Edition
ISO
4257
Liquefied Petroleum Gases - Method of Sampling Second Edition
ISO
4259
Petroleum Products - Determination and Application of Precision Data in Relation to Methods of Test Third Edition
ISO
4260
Petroleum Products and Hydrocarbons - Determination of Sulfur Content - Wickbold Combustion Method First Edition
ISO
4261
Petroleum Products - Fuels (Class F) - Specification of Gas Turbine Fuels for Industrial and Marine Applications First Edition
ISO
4262
Petroleum Products - Determination of Carbon Residue - Ramsbottom Method Second Edition
Petroleum and Related Products - Determination of the Ageing Behaviour of Inhibited Oils and Fluids - TOST Test - Part 1: Procedure
ISO
4263-1
for Mineral Oils First Edition; Replaces ISO 4263
Petroleum and Related Products - Determination of the Ageing Behaviour of Inhibited Oils and Fluids - TOST Test Part 2: Procedure
ISO
4263-2
for Category HFC Hydraulic Fluids First Edition; Replaces ISO 4263
Petroleum and related products Determination of the ageing behaviour of inhibited oils and fluids TOST test Part 3: Anhydrous
ISO
4263-3
procedure for synthetic hydraulic fluids First Edition
Petroleum and related products Determination of the ageing behaviour of inhibited oils and fluids TOST test Part 4: Procedure for
ISO
4263-4
industrial gear oils First Edition
ISO
4264
Petroleum Products - Calculation of Cetane Index of Middle-Distillate Fuels by the Four-Variable Equation Second Edition
Petroluem and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 1:
ISO
4266-1
Meassurement of Level in Atmospheric Tanks First Edition
Petroleum and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 2:
ISO
4266-2
Measurement of Level in Marine Vessels First Edition
Petroleum and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 3:
ISO
4266-3
Measurement of Level in Pressurized Storage Tanks (Non-Refrigerated) First Edition
Petroleum and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 4:
ISO
4266-4
Measurement of Temperature in Atmospheric Tanks First Edition
Petroleum and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 5:
ISO
4266-5
Measurement of Temperature in Marine Vessels First Edition
Petroleum and Liquid Petroleum Products - Measurement of Level and Temperature in Storage Tanks by Automatic Methods - Part 6:
ISO
4266-6
Measurement of Temperature in Pressurized Storage Tanks (Non-Refrigerated) First Edition
Petroleum and Liquid Petroleum Products - Calculation of Oil Quantities - Part 2: Dynamic Measurement First Edition; (CEN EN ISO
ISO
4267-2
4267-2)
ISO
4268
Petroleum and Liquid Petroleum Products - Temperature Measurements - Manual Methods First Edition
Petroleum and Liquid Petroleum Products - Tank Calibration by Liquid Measurement - Incremental Method Using Volumetric Meters
ISO
4269
First Edition
Cryolite, Natural and Artificial, and Aluminium Fluoride for Industrial Use - Determination of Sulphate Content - Barium Sulphate
ISO
4280
Gravimetric Method First Edition; (Erratum-1978)
Sodium Hexafluorosilicate for Industrial Use - Determination of Free Acidity and Total Hexafluorosilicate Content - Titrimetric Method
ISO
4281
First Edition
ISO
4282
Acid-Grade and Ceramic-Grade Fluorspar - Determination of Loss in Mass at 105 Degrees C Second Edition
ISO
4283
Grades of Fluorspar - Determination of Carbonate Content - Titrimetric Method Third Edition
ISO
4284
Acid-Grade and Ceramic-Grade Fluorspar - Determination Sulfide Content - Iodometric Iodometric Method Third Edition
Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Terms, Definitions and Surface Texture Parameters
Specification Geometrique Des Produits (GPS) - Etat De Surface: Methode Du Profil - Termes, Definitions Et Parametres D'Etat De
ISO
4287
Surface First Edition; Technical Corrigendum 1-1998; Corrigendum 2: 2/15/2005
Geometrical Product Specifications (GPS) - Surface Texture: Profile Method - Rules and Procedures for the Assessment of Surface
ISO
4288
Texture Second Edition; Technical Corrigendum 1: 06/15/1998
ISO
4291
Methods for the Assessment of Departure from Roundness - Measurement of Variations in Radius First Edition
ISO
4292
Methods for the Assessment of Departure from Roundness - Measurement by Two- and Three-Point Methods First Edition
Manganese Ores and Concentrates - Determination of Phosphorus Content - Extraction- Molybdovanadate Photometric Method Firts
ISO
4293
Edition; Replaces ISO R 321: 1963
Manganese Ores and Concentrates - Determination of Copper Content - Extraction- Spectrometric and Spectrometric Methods
ISO
4294
Second Edition; Replaces ISO R 322: 1978
Manganese Ores and Concentrates - Determination of Aluminium Content - Photometric and Gravimetric Methods Second Edition;
ISO
4295
Replaces ISO R 318: 1963
ISO
4296-1
Manganese Ores - Sampling - Part 1: Increment Sampling First Edition
ISO
4296-2
Manganese Ores - Sampling - Part 2: Preparation of Samples First Edition
ISO
4297
Manganese Ores and Concentrates - Methods of Chemical Analysis - General Instructions First Edition
Manganese Ores and Concentrates - Determination of Manganese Content - Potentiometric Method Second Edition; Replaces ISO R
ISO
4298
319: 1963
ISO
4299
Manganese Ores - Determination of Moisture Content Second Edition
ISO
4301-1
Cranes and Lifting Appliances - Classification - Part 1: General Second Edition
ISO
4301-2
Lifting Appliances - Classification - Part 2: Mobile Cranes First Edition
ISO
4301-3
Cranes - Classification - Part 3: Tower Cranes First Edition
ISO
4301-4
Cranes and Related Equipment - Classification - Part 4: Jib Cranes First Edition
ISO
4301-5
Cranes - Classification - Part 5: Overhead Travelling and Portal Bridge Cranes First Edition
ISO
4302
Cranes - Wind Load Assessment First Edition
ISO
4304
Cranes Other Than Mobile and Floating Cranes - General Requirements for Stability First Edition
ISO
4305
Mobile Cranes - Determination of Stability Second Edition
ISO
4306-1
Cranes - Vocabulary - Part 1: General Third Edition
ISO
4306-2
Cranes - Vocabulary - Part 2: Mobile Cranes Second Edition
ISO
4306-3
Cranes - Vocabulary - Part 3: Tower Cranes Third Edition
Cranes - Vocabulary - Part 5: Bridge and gantry cranes Appareils de levage Ó charge suspendue Vocabulaire Partie 5: Ponts et
ISO
4306-5
portiques roulants First Edition
ISO
4308-1
Cranes and Lifting Appliances - Selection of Wire Ropes - Part 1: General Third Edition
ISO
4308-2
Cranes and Lifting Appliances - Selection of Wire Ropes - Part 2: Mobile Cranes - Coefficient of Utilization First Edition
ISO
4309
Cranes Wire ropes Care, maintenance, installation, examination and discard Third Edition
ISO
4310
Cranes - Test Code and Procedures First Edition
Anionic and Non-Ionic Surface Active Agents - Determination of the Critical Micellization Concentration - Method by Measuring
ISO
4311
Surface Tension with a Plate, Stirrup or Ring First Edition
Surface Active Agents - Evaluation of Certain Effects of Laundering - Methods of Analysis and Test for Unsoiled Cotton Control Cloth
ISO
4312
Second Edition
Washing Powders - Determination of Total Phosphorus (V) Oxide Content - Quinoline Phosphomolybdate Gravimetric Method First
ISO
4313
Edition
ISO
4314
Surface Active Agents - Determination of Free Alkalinity or Free Acidity - Titrimetric Method First Edition
ISO
4315
Surface Active Agents - Determination of Alkalinity - Titrimetric Method First Edition
ISO
4316
Surface Active Agents - Determination of pH of Aqueous Solutions - Potentiometric Method First Edition
ISO
4317
Surface-Active Agents and Detergents - Determination of Water Content - Karl Fischer Method Second Edition
ISO
4318
Surface Active Agents and Soaps - Determination of Water Content - Azeotropic Distillation Method Second Edition
ISO
4319
Surface Active Agents - Detergents for Washing Fabrics - Guide for Comparative Testing of Performance First Edition
ISO
4320
Non-Ionic Surface Active Agents - Determination of Cloud Point Index - Volumetric Method First Edition; (Erratum-1980)
ISO
4321
Washing Powders - Determination of Active Oxygen Content - Titrimetric Method First Edition
ISO
4322
Non-Ionic Surface Active Agents - Determination of Sulphated Ash - Gravimetric Method First Edition
ISO
4323
Soaps - Determination of Chloride Content - Potentiometric Method First Edition
ISO
4324
Surface Active Agents - Powders and Granules - Measurement of the Angle of Repose First Edition
ISO
4325
Soaps and Detergents - Determination of Chelating Agent Content - Titrimetric Method Second Edition
Non-Ionic Surface Active Agents - Polyethoxylated Derivatives - Determination of Hydroxyl Value - Acetic Anhydride Method First
ISO
4326
Edition
Non-Ionic Surface Active Agents - Polyalkoxylated Derivatives - Determination of Hydroxyl Value - Phthalic Anhydride Method First
ISO
4327
Edition; (Erratum-1980)
ISO
4337
Information Processing - Interchangeable Magnetic Twelve-Disk Pack (100 Mbytes) First Edition
Information Processing - Magnetic Tape Cassette and Cartridge Labelling and File Structure for Information Interchange First Edition;
ISO
4341
(ANSI 4341-1978)
ISO
4342
Numerical Control of Machines - NC Processor Input - Basic Part Program Reference Language First Edition
ISO
4343
Industrial Automation Systems - Numerical Control of Machines - NC Processor Output - Post-Processor Commands Second Edition
ISO
4344
Steel wire ropes for lifts Minimum requirements Second Edition
ISO
4345
Steel Wire Ropes - Fibre Main Cores - Specification Second Edition
ISO
4346
Steel Wire Ropes for General Purposes - Lubricants - Basic Requirements First Edition
ISO
4347
Leaf chains, clevises and sheaves Dimensions, measuring forces and tensile strengths Fourth Edition
ISO
4348
Flat-Top Chains and Associated Chain Wheels for Conveyors Second Edition
ISO
4354
Wind Actions on Structures First Edition
ISO
4355
Bases for Design of Structures - Determination of Snow Loads on Roofs Second Edition
ISO
4356
Bases for the Design of Structures - Deformations of Buildings at the Serviceability Limit States First Edition; (PNS 1091: 1992)
Liquid Flow Measurement in Open Channels - Rectangular, Trapezoidal and U-Shaped Flumes First Edition; Technical Corrigendum
ISO
4359
1: 10/01/1999 [Superseded: BSI BS 3680 PART 4C]
ISO
4360
Liquid Flow Measurement in Open Channels by Weirs and Flumes - Triangular Profile Weirs Second Edition
Hydrometric Determinations - Flow Measurement in Open Channels Using Structures - Trapezoidal Broad-Crested Weirs Second
ISO
4362
Edition
ISO
4363
Measurement of liquid flow in open channels Methods for measurement of characteristics of suspended sediment Third Edition
ISO
4364
Measurement of Liquid Flow in Open Channels - Bed Material Sampling Second Edition; Technical Corrigendum 1: 08/01/2000
Liquid flow in open channels Sediment in streams and canals Determination of concentration, particle size distribution and relative
ISO
4365
density Second Edition
ISO
4366
Hydrometry ù Echo Sounders For Water Depth Measurements Second Edition
ISO
4369
Measurement of Liquid Flow in Open Channels - Moving-Boat Method First Edition
Measurement of Liquid Flow in Open Channels by Weirs and Flumes - End Depth Method for Estimation of Flow in Non-Rectangular
ISO
4371
Channels with a Free Overfall (Approximate Method) First Edition
ISO
4373
Measurement of Liquid Flow in Open Channels - Water-Level Measuring Devices Second Edition
ISO
4374
Liquid Flow Measurement in Open Channels - Round-Nose Horizontal Broad-Crested Weirs Second Edition
ISO
4375
Hydrometric Determinations - Cableway Systems for Stream Gauging Second Edition
ISO
4377
Hydrometric Determinations - Flow Measurement in Open Channels Using Structures - Flat-V Weirs Third Edition
Plain Bearings - Terms, Definitions and Classification - Part 1: Design, Bearing Materials and Their Properties Paliers Lisses -
Termes, Definitions Et Classification - Partie 1: Conception, Materiaux Pour Paliers Et Leurs Proprietes Second Edition; Corrected
ISO
4378-1
and Reprinted 02/15/1999
ISO
4378-2
Plain Bearings - Terms, Definitions and Classification - Part 2: Friction and Wear First Edition
ISO
4378-3
Plain Bearings - Terms, Definitions and Classification - Part 3: Lubrication First Edition
Plain Bearings - Terms, Definitions and Classification - Part 4: Calculation Parameters and Their Symbol Paliers Lisses - Termes,
ISO
4378-4
Definitions Et Classification - Partie 4: Parametres De Calcul Et Leur Symbole First Edition; Corrected and Reprinted, 10/01/1998
ISO
4379
Plain Bearings - Copper Alloy Bushes Second Edition (Corrected and Reprinted - 1995)
ISO
4381
Plain Bearings - Lead and Tin Casting Alloys for Multilayer Plain Bearings Third Edition
ISO
4382-1
Plain Bearings - Copper Alloys - Part 1: Cast Copper Alloys for Solid and Multilayer Thick- Walled Plain Bearings Second Edition
ISO
4382-2
Plain Bearings - Copper Alloys - Part 2: Wrought Copper Alloys for Solid Plain Bearings Second Edition
ISO
4383
Plain Bearings - Multilayer Materials for Thin-Walled Plain Bearings Third Edition
ISO
4384-1
Plain Bearings - Hardness Testing of Bearing Metals - Part 1: Compound Materials Second Edition
ISO
4384-2
Plain Bearings - Hardness Testing of Bearing Metals - Part 2: Solid Materials First Edition
ISO
4385
Plain Bearings - Compression Testing of Metallic Bearing Materials First Edition
ISO
4386-1
Plain Bearings - Metallic Multilayer Plain Bearings - Part 1: Non-Destructive Ultrasonic Testing of Bond Second Edition
Plain Bearings - Metallic Multilayer Plain Bearings - Part 2: Destructive Testing of Bond for Bearing Metal Layer Thicknesses Greater
ISO
4386-2
Than or Equal to 2 mm First Edition
ISO
4386-3
Plain Bearings - Metallic Multilayer Plain Bearings - Part 3: Non-Destructive Penetrant Testing First Edition
Cigarettes - Determination of Total and Nicotine-Free Dry Particulate Matter Using a Routine Analytical Smoking Machine Third
ISO
4387
Edition
ISO
4388
Cigarettes - Determination of the Smoke Condensate Retention Index of a Filter - Direct Spectrometric Method Second Edition
ISO
4389
Tobacco and Tobacco Products - Determination of Organochlorine Pesticide Residues - Gas Chromatographic Method Third Edition
ISO
4391
Hydraulic Fluid Power - Pumps, Motors and Integral Transmissions - Parameter Definitions and Letter Symbols Second Edition
Hydraulic Fluid Power - Determination of Characteristics of Motors - Part 1: At Constant Low Speed and at Constant Pressure Third
ISO
4392-1
Edition
ISO
4392-2
Hydraulic Fluid Power - Determination of Characteristics of Motors - Part 2: Startability Third Edition
ISO
4392-3
Hydraulic Fluid Power - Determination of Characteristics of Motors - Part 3: At Constant Flow and at Constant Torque First Edition
ISO
4393
Fluid Power Systems and Components - Cylinders - Basic Series of Piston Strokes First Edition
Fluid Power Systems and Components - Cylinder Barrels - Part 1: Requirements for Steel Tubes with Specially Finished Bores First
ISO
4394-1
Edition
ISO
4395
Fluid Power Systems and Components - Cylinders - Piston Rod Thread Dimensions and Types First Edition
Fluid Power Systems and Components - Connectors and Associated Components - Nominal Outside Diameters of Tubes and
ISO
4397
Nominal Inside Diameters of Hoses Second Edition
ISO
4399
Fluid Power Systems and Components - Connectors and Associated Components - Nominal Pressures Second Edition
Fluid Power Systems and Components - Three-Pin Electrical Plug Connectors with Earth Contact - Characteristics and Requirements
ISO
4400
Third Edition
ISO
4401
Hydraulic fluid power - Four-port directional control valves - Mounting surfaces Third Edition
Petroleum and Related Products - Determination of the Corrosion Resistance of Fire-Resistant Hydraulic Fluids - Part 1: Water-
ISO
4404-1
Containing Fluids First Edition; Replaces ISO 4404
Petroleum and related products Determination of the corrosion resistance of fire-resistant hydraulic fluids Part 2: Non-aqueous fluids
ISO
4404-2
First Edition; Replaces ISO 4404
Hydraulic Fluid Power - Fluid Contamination - Determination of Particulate Contamination by the Gravimetric Method First Edition
ISO
4405
Supersedes (NFPA) T2.9.14
ISO
4406
Hydraulic Fluid Power - Fluids - Method for Coding the Level of Contamination by Solid Particles Second Edition
Hydraulic Fluid Power - Fluid Contamination - Determination of Particulate Contamination by the Counting Method Using an Optical
ISO
4407
Microscope Second Edition
Hydraulic fluid power ù Positive-displacement pumps, motors and integral transmissions ù Methods of testing and presenting basic
ISO
4409
steady state performance Second Edition
ISO
4411
Hydraulic Fluid Power - Valves - Determination of Pressure Differential/Flow Characteristics First Edition
Hydraulic Fluid Power - Test Code for Determination of Airborne Noise Levels - Part 1: Pumps Second Edition Supersedes (NFPA)
ISO
4412-1
B93.71M
ISO
4412-2
Hydraulic Fluid Power - Test Code for Determination of Airborne Noise Levels - Part 2: Motors Second Edition
Hydraulic Fluid Power - Test Code for Determination of Airborne Noise Levels - Part 3: Pumps - Method Using a Parallelepiped
ISO
4412-3
Microphone Array First Edition
ISO
4413
Hydraulic Fluid Power - General Rules Relating to Systems Second Edition
ISO
4414
Pneumatic Fluid Power - General Rules Relating to Systems Second Edition
ISO
4415
Size Designation of Clothes - Men s and Boys Underwear, Nightwear and Shirts First Edition; Corrigendum 1: 1990
Size Designation of Clothes - Women s and Girls Underwear, Nightwear, Foundation Garments and Shirts First Edition;
ISO
4416
Corrigendum 1: 1990
ISO
4417
Size Designation of Clothes - Headwear First Edition; Amendment Slip: 12-15-1977; Amendment Slip: 05-01-1978
ISO
4418
Size Designation of Clothes - Gloves First Edition
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 1: General First
ISO
4422-1
Edition; Supersedes ISO 4422: 1990
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 2: Pipes (With or
ISO
4422-2
Without Integral Sockets) First Edition
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 3: Fittings and Joints
ISO
4422-3
First Edition; Supersedes ISO 4422: 1990
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 4: Valves and Ancillary
ISO
4422-4
Equipment First Edition; Supersedes ISO 4422: 1990
Pipes and Fittings Made of Unplasticized Poly(Vinyl Chloride) (PVC-U) for Water Supply - Specifications - Part 5: Fitness for Purpose
ISO
4422-5
of the System First Edition; Supersedes ISO 4422: 1990
ISO
4427-2
Plastics piping systems ù Polyethylene (PE) pipes and fittings for water supply ù Part 2: Pipes First Edition [Replaced: ISO 4427]
ISO
4427-3
Plastics piping systems ù Polyethylene (PE) pipes and fittings for water supply ù Part 3: Fittings First Edition
ISO
4427-5
Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 5: Fitness for purpose of the system First Edition
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 1: Immersion Test Method First Edition; Replaces ISO
ISO
4433-1
4433
ISO
4433-2
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 2: Polyolefin Pipes First Edition; Replaces ISO 4433
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 3: Unplasticized Poly(Vinyl Chloride) (PVC-U), High-
ISO
4433-3
Impact Poly(Vinyl Chloride) (PVC-HI) and Chlorinated Poly(Vinyl Chloride) (PVC-C) Pipes First Edition; Replaces ISO 4433
Thermoplastics Pipes - Resistance to Liquid Chemicals - Classification - Part 4: Poly(Vinylidene Fluoride) (PVDF) Pipes First Edition;
ISO
4433-4
Replaces ISO 4433
Unplasticized Polyvinyl Chloride (PVC) Adaptor Fittings for Pipes Under Pressure - Laying Length and Size of Threads - Metric Series
ISO
4434
First Edition
Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U) Secon
ISO
4435
Edition
ISO
4437
Buried polyethylene (PE) pipes for the supply of gaseous fuels ù Metric series ù Specifications Third Edition
ISO
4439
Unplasticized Polyvinyl Chloride (PVC) Pipes and Fittings - Determination and Specification of Density First Edition
ISO
4440-1
Thermoplastics Pipes and Fittings - Determination of Melt Mass-Flow Rate - Part 1: Test Method First Edition
ISO
4440-2
Thermoplastics Pipes and Fittings - Determination of Melt Mass-Flow Rate - Part 2: Test Conditions First Edition
Measurement Methods for Building - Setting-Out and Measurement - Part 1: Planning and Organization, Measuring Procedures,
ISO
4463-1
Acceptance Criteria First Edition
ISO
4463-2
Measurement Methods for Building - Setting-Out and Measurement - Part 2: Measuring Stations and Targets First Edition
Measurement Methods for Building - Setting-Out and Measurement - Part 3: Check-Lists for the Procurement of Surveys and
ISO
4463-3
Measurement Services First Edition
ISO
4468
Gear Hobs - Single Start - Accuracy Requirements First Edition
ISO
4469
Wood - Determination of Radial and Tangential Shrinkage First Edition
ISO
4470
Sawn Timber - Determination of the Average Moisture Content of a Lot First Edition; (PNS 1007: 1989)
Wood - Sampling Sample Trees and Logs for Determination of Physical and Mechanical Properties of Wood in Homogeneous
ISO
4471
Stands First Edition
ISO
4472
Coniferous and Broadleaved Sawn Timber - Transportation Packages First Edition
ISO
4473
Coniferous and Broadleaved Tree Sawlogs - Visible Defects - Classification First Edition
ISO
4474
Coniferous and Broadleaved Tree Sawlogs - Visible Defects - Terms and Definitions First Edition
ISO
4475
Coniferous and Broadleaved Tree Sawlogs - Visible Defects - Measurement First Edition
ISO
4476
Coniferous and Broadleaved Sawlogs - Sizes - Vocabulary First Edition
ISO
4480
Coniferous Sawlogs - Measurement of Sizes and Determination of Volume First Edition
ISO
4481
Cutlery and Flatware - Nomenclature First Edition; (PNS 889: 1993)
ISO
4489
Sintered Hardmetals - Sampling and Testing First Edition; (CEN EN 24489: 1993)
ISO
4490
Metallic Powders - Determination of Flow Time by Means of a Calibrated Funnel (Hall Flowmeter) Second Edition
Metallic Powders - Determination of Oxygen Content by Reduction Methods - Part 1: General Guidelines First Edition; (CEN EN
ISO
4491-1
24491-1: 1993)
Metallic Powders - Determination of Oxygen Content by Reduction Methods - Part 2: Loss of Mass on Hydrogen Reduction
ISO
4491-2
(Hydrogen Loss) Second Edition
ISO
4491-3
Metallic Powders - Determination of Oxygen Content by Reduction Methods - Part 3: Hydrogen-Reducible Oxygen Second Edition
Metallic Powders - Determination of Oxygen Content by Reduction Methods - Part 4: Total Oxygen by Reduction-Extraction First
ISO
4491-4
Edition; (CEN EN 24491-4: 1993)
Metallic Powders, Excluding Powders for Hardmetals - Determination of Dimensional Changes Associated with Compacting and
ISO
4492
Sintering Second Edition; (CEN EN 24492: 1993)
Metallic Powders - Determination of Acid-Insoluble Content in Iron, Copper, Tin and Bronze Powders First Edition; (CEN EN 24496:
ISO
4496
1993)
ISO
4497
Metallic Powders - Determination of Particle Size by Dry Sieving First Edition; (CEN EN 24497: 1993)
Sintered metal materials, excluding hardmetals - Determination of apparent hardness and microhardness First edition; Cancels and
ISO
4498
Replaces ISO 4498-1: 1990 and ISO 4498-2: 1981
ISO
4499
Hardmetals - Metallographic Determination of Microstructure First Edition; (CEN EN 24499: 1993)
ISO
4501
Hardmetals - Determination of Titanium - Photometric Peroxide Method First Edition; (CEN EN 24501: 1993)
Hardmetals - Determination of Contents of Metallic Elements by X-Ray Fluorescence - Fusion Method First Edition; (CEN EN 24503:
ISO
4503
1993)
ISO
4505
Hardmetals - Metallographic Determination of Porosity and Uncombined Carbon First Edition; (CEN EN 24505: 1993)
ISO
4506
Hardmetals - Compression Test First Edition; (CEN EN 24506:1993)
Sintered Ferrous Materials, Carburized or Carbonitrided - Determination and Verification of Case-Hardening Depth by a Micro-
ISO
4507
Hardness Test Second Edition
ISO
4510-1
Earth-Moving Machinery - Service Tools - Part 1: Common Maintenance and Adjustment Tools Second Edition
ISO
4510-2
Earth-Moving Machinery - Service Tools - Part 2: Mechanical Pullers and Pushers Second Edition
Petroleum and Liquid Petroleum Products - Equipment for Measurement of Liquid Levels in Storage Tanks - Manual Methods First
ISO
4512
Edition
ISO
4513
Road vehicles Visibility Method for establishment of eyellipses for driver s eye location Second Edition
ISO
4516
Metallic and Other Inorganic Coatings - Vickers and Knoop Microhardness Tests Second Edition
Metallic Coatings - Measurement of Coating Thickness - Profilometric Method First Edition; (CEN EN ISO 4518: 1995) (PNS 679:
ISO
4518
1990)
Electrodeposited Metallic Coatings and Related Finishes - Sampling Procedures for Inspection by Attributes First Edition; (Erratum-
ISO
4519
1981) (PNS 674: 1990)
ISO
4520
Chromate Conversion Coatings on Electroplated Zinc and Cadmium Coatings First Edition; (PNS 680: 1990)
ISO
4521
Metallic Coatings - Electrodeposited Silver and Silver Alloy Coatings for Engineering Purposes First Edition
Metallic Coatings - Test Methods for Electrodeposited Silver and Silver Alloy Coatings - Part 1: Determination of Coating Thickness
ISO
4522-1
First Edition
ISO
4522-2
Metallic Coatings - Test Methods for Electrodeposited Silver and Silver Alloy Coatings - Part 2: Adhesion Tests First Edition
Metallic Coatings - Test Methods for Electrodeposited Silver and Silver Alloy Coatings - Part 3: Determination of the Presence of
ISO
4522-3
Residual Salts First Edition
ISO
4523
Metallic Coatings - Electrodeposited Gold and Gold Alloy Coatings for Engineering Purposes First Edition
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 1: Determination of Coating Thickness
ISO
4524-1
First Edition
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 2: Mixed Flowing Gas (MFG)
ISO
4524-2
Environmental Tests Second Edition
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 3: Electrographic Tests for Porosity First
ISO
4524-3
Edition; (Corrected and Reprinted - 1986)
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 4: Determination of Gold Content First
ISO
4524-4
Edition
ISO
4524-5
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 5: Adhesion Tests First Edition
Metallic Coatings - Test Methods for Electrodeposited Gold and Gold Alloy Coatings - Part 6: Determination of the Presence of
ISO
4524-6
Residual Salts First Edition; (CEN EN ISO 4524-6: 1994)
ISO
4525
Metallic Coatings - Electroplated Coatings of Nickel Plus Chromium on Plastics Materials Second Edition
ISO
4526
Metallic coatings Electroplated coatings of nickel for engineering purposes Second Edition
ISO
4527
Metallic coatings Autocatalytic (electroless) nickel-phosphorus alloy coatings Specification and test methods Second Edition
Vitreous and Porcelain Enamel Finishes - Selection of Test Methods for Vitreous and Porcelain Enamelled Areas of Articles First
ISO
4528
Edition
ISO
4530
Vitreous and Porcelain Enamelled Manufactured Articles - Determination of Resistance to Heat First Edition
Vitreous and Porcelain Enamels - Release of Lead and Cadmium from Enamelled Ware in Contact with Food - Part 1: Method of
ISO
4531-1
Test First Edition
Vitreous and Porcelain Enamels - Release of Lead and Cadmium from Enamelled Ware in Contact with Food - Part 2: Permissible
ISO
4531-2
Limits First Edition
ISO
4532
Vitreous and Porcelain Enamels - Determination of the Resistance of Enamelled Articles to Impact - Pistol Test First Edition
ISO
4533
Vitreous and Porcelain Enamels - Determination of Resistance to Hot Detergent Solutions Used for Washing Textiles First Edition
ISO
4534
Vitreous and Porcelain Enamels - Determination of Fluidity Behaviour - Fusion Flow Test First Edition
Vitreous and Porcelain Enamels - Apparatus for Determination of Resistance to Hot Detergent Solutions Used for Washing Textiles
ISO
4535
First Edition
ISO
4536
Metallic and Non-Organic Coatings on Metallic Substrates - Saline Droplets Corrosion Test (SD Test) First Edition
ISO
4538
Metallic Coatings - Thioacetamide Corrosion Test (TAA Test) First Edition; (CEN EN ISO 4538: 1995)
ISO
4539
Electrodeposited Chromium Coatings - Electrolytic Corrosion Testing (EC Test) First Edition
ISO
4541
Metallic and Other Non-Organic Coatings - Corrodkote Corrosion Test (CORR Test) First Edition; (CEN EN ISO 4541: 1994)
Metallic and Other Non-Organic Coatings - General Rules for Corrosion Tests Applicable for Storage Conditions First Edition; (CEN
ISO
4543
EN ISO 4543: 1994)
ISO
4545-1
Metallic materials Knoop hardness test Part 1: Test method First Edition; Replaces ISO 4545: 1993
Metallic materials Knoop hardness test Part 2: Verification and calibration of testing machines First Edition; Replaces ISO
ISO
4545-2
4546:1993
ISO
4545-3
Metallic materials Knoop hardness test Part 3: Calibration of reference blocks First Edition; Replaces ISO 4547: 1993
ISO
4545-4
Metallic materials Knoop hardness test Part 4: Table of hardness values First Edition; Replaces ISO 10250: 1994
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 1: Differential Pressure/Flow
ISO
4548-1
Characteristics First Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 2: Element By-Pass Valve Characteristics
ISO
4548-2
Second Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 3: Resistance to High Pressure and to
ISO
4548-3
Elevated Temperature Second Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 4: Initial Particle Retention Efficiency, Life
ISO
4548-4
and Cumulative Efficiency (Gravimetric Method) First Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 5: Cold Start Simulation and Hydraulic
ISO
4548-5
Pulse Durability Test First Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 6: Static Burst Pressure Test First Edition;
ISO
4548-6
Corrigendum 1-1990
ISO
4548-7
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 7: Vibration Fatigue Test First Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 9: Inlet and Outlet Anti-Drain Valve Tests
ISO
4548-9
First Edition;
ISO
4548-11
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 11: Self-Cleaning Filters First Edition
Methods of Test for Full-Flow Lubricating Oil Filters for Internal Combustion Engines - Part 12: Filtration Efficiency Using Particle
ISO
4548-12
Counting, and Contaminant Retention Capacity First Edition
ISO
4551
Ferroalloys - Sampling and Sieve Analysis First Edition; (Corrected and Reprinted - 1988)
Ferroalloys - Sampling and Sample Preparation for Chemical Analysis - Part 1: Ferrochromium, Ferrosilicochromium, Ferrosilicon,
ISO
4552-1
Ferrosilicomanganese, Ferromanganese First Edition
Ferroalloys - Sampling and Sample Preparation for Chemical Analysis - Part 2: Ferrotitanium, Ferromolybdenum, Ferrotungsten,
ISO
4552-2
Ferroniobium, Ferrovanadium First Edition
ISO
4566
Small Craft with Inboard Engine - Propeller Shaft Ends and Bosses with 1:10 Taper Second Edition
ISO
4568
Shipbuilding Sea-going vessels Windlasses and anchor capstans Third Edition
ISO
4570
Tyre Valve Threads Filetages De Valves Pour Pneumatiques First Edition; Replaces ISO 4570-1, 4570-2 and 4570-3
Manganese Ores and Concentrates - Determination of Potassium and Sodium Content - Flame Atomic Emission Spectrometric
ISO
4571
Method First Edition
ISO
4574
Plastics - PVC Resins for General Use - Determination of Hot Plasticizer Absorption First Edition
ISO
4575
Plastics ù Poly(vinyl chloride) pastes ù Determination of apparent viscosity using the Severs rheometer Third Edition
ISO
4576
Plastics - Polymer Dispersions - Determination of Sieve Residue (Gross Particle and Coagulum Content) Second Edition
ISO
4577
Plastics - Polypropylene and Propylene-Copolymers - Determination of Thermal Oxidative Stability in Air - Oven Method First Edition
ISO
4578
Adhesives - Determination of Peel Resistance of High-Strength Adhesive Bonds - Floating Roller Method Third Edition
Plastics - Styrene/Acrylonitrile Copolymers - Determination of Residual Acrylonitrile Monomer Content - Gas Chromatography Method
ISO
4581
Second Edition
Plastics - Determination of Changes in Colour and Variations in Properties After Exposure to Daylight Under Glass, Natural
ISO
4582
Weathering or Laboratory Light Sources Second Edition
ISO
4586-1
High-pressure decorative laminates Sheets made from thermosetting resins Part 1: Classification and specifications Fifth Edition
ISO
4586-2
High-pressure decorative laminates Sheets made from thermosetting resins Part 2: Determination of properties Fifth Edition
Adhesives - Determination of Tensile Lap-Shear Strength of Rigid-to-Rigid Bonded Assemblies Third Edition [Replaced: GME GME
ISO
4587
60432, GME GME 60432]
ISO
4589-1
Plastics - Determination of Burning Behavior by Oxygen Index Part 1: Guidance First Edition
Plastics Determination of burning behaviour by oxygen index Part 2: Ambient-temperature test First Edition; Amendment 1:
ISO
4589-2
01/15/2005
Plastics - Determination of Burning Behaviour by Oxygen Index - Part 3: Elevated-Temperature Test First Edition; CEN EN ISO 4589-
ISO
4589-3
3: 1996
ISO
4590
Rigid Cellular Plastics - Determination of the Volume Percentage of Open Cells and of Closed Cells Second Edition
Plastics - Film and Sheeting - Determination of Average Thickness of a Sample, and Average Thickness and Yield of a Roll, by
ISO
4591
Gravimetric Techniques (Gravimetric Thickness) Second Edition
ISO
4592
Plastics - Film and Sheeting - Determination of Length and Width Second Edition
ISO
4593
Plastics - Film and Sheeting - Determination of Thickness by Mechanical Scanning Second Edition
ISO
4597-1
Plastics - Hardeners and accelerators for epoxy resins - Part 1: Designation Second Edition
ISO
4602
Reinforcements - Woven Fabrics - Determination of Number of Yarns per Unit Length of Warp and Weft Second Edition
ISO
4603
Textile Glass - Woven Fabrics - Determination of Thickness Second Edition
ISO
4604
Textile Glass - Woven Fabrics - Determination of Conventional Flexural Stiffness - Fixed-Angle Flexometer Method First Edition
ISO
4606
Textile Glass - Woven Fabric - Determination of Tensile Breaking Force and Elongation at Break by the Strip Method Second Edition
Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride for General Use - Determination of Plasticizer Absorption at Room
ISO
4608
Temperature Third Edition
ISO
4610
Plastics - Vinyl Chloride Homopolymer and Copolymer Resins - Sieve Analysis Using Air-Jet Sieve Apparatus Second Edition
ISO
4611
Plastics - Determination of the Effects of Exposure to Damp Heat, Water Spray and Salt Mist Second Edition
ISO
4612
Plastics - Preparation of PVC Pastes for Test Purposes - Planetary-Mixer Method Second Edition
ISO
4613-1
Plastics - Ethylene/Vinyl Acetate (E/VAC) Moulding and Extrusion Materials - Part 1: Designation and Specification Second Edition
Plastics - Ethylene/Vinyl Acetate (E/VAC) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and
ISO
4613-2
Determination of Properties Second Edition; (CEN EN ISO 4613-2: 1995) Second Editon; Amendment 1:06/15/2004
ISO
4614
Plastics - Malamine-Formaldehyde Moulding - Determination of Extractable Formaldehyde First Edition
ISO
4615
Plastics - Unsaturated polyesters and epoxide resins - Determination of total chlorine content First Edition
Paints and varnishes Terms and definitions Peintures et vernis Termes et dÚfintions First Edition; Replaces ISO 4618-1:1998, ISO
ISO
4618
4618-2:1999 and ISO 4618-3:1999
ISO
4619
Driers for Paints and Varnishes Second Edition
ISO
4620
Cadmium Pigments - Specifications and Methods of Test First Edition
ISO
4621
Chrome Oxide Green Pigments - Specifications and Methods of Test First Edition
ISO
4622
Paints and Varnishes - Pressure Test for Stackability Second Edition; (CEN EN ISO 4622)
ISO
4623-1
Paints and Varnishes - Determination of Resistance to Filiform Corrosion - Part 1: Steel Substrates First Edition
ISO
4623-2
Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates First Edition
ISO
4624
Paints and Varnishes - Pull-Off Test for Adhesion Second Edition
ISO
4625-1
Binders for paints and varnishes Determination of softening point Part 1:Ring-and-ball method First Edition; Replaces ISO 4625
ISO
4625-2
Binders for paints and varnishes Determination of softening point Part 2:Cup-and-ball method First Edition; Replaces ISO 4625
ISO
4626
Volatile Organic Liquids - Determination of Boiling Range of Organic Solvents Used as Raw Materials First Edition
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-1
changes in appearance Part 1: General introduction and designation system Third Edition
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-2
changes in appearance Part 2: Assessment of degree of blistering Second Edition
Paints and Varnishes - Evaluation of Degradation of Paint Coatings - Designation of Intensity, Quantity and Size of Common Types of
ISO
4628-3
Defect - Part 3: Designation of Degree of Rusting First Edition Second Edition
Paints and Varnishes - Evaluation of Degradation of Coatings - Designation of Quantity and Size of Defects, and of Intensity of
ISO
4628-4
Uniform Changes in Appearance - Part 4: Assessment of Degree of Cracking Second Edition
Paints and Varnishes - Evaluation of Degradation of Coatings - Designation of Quantity and Size of Defects, and of Intesity of
ISO
4628-5
Uniform Changes in Appearance - Part 5: Assessment of Degree of Flaking Second Edition
Paints and varnishes ù Evaluation of degradation of coatings ù Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-6
changes in appearance ù Part 6: Assessment of degree of chalking by tape method Second Edition
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-7
changes in appearance Part 7: Assessment of degree of chalking by velvet method First Edition
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-8
changes in appearance Part 8: Assessment of degree of delamination and corrosion around a scribe First edition
Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform
ISO
4628-10
changes in appearance Part 10: Assessment of degree of filiform corrosion First Edition
ISO
4629
Binders for Paints and Varnishes - Determination of Hydroxyl Value - Titrimetric Method Second Edition
Clear liquids Estimation of colour by the Gardner colour scale Part 1: Visual method First Edition; Cancels and Replaces ISO
ISO
4630-1
4630:1997
ISO
4630-2
Clear liquids Estimation of colour by the Gardner colour scale Part 2: Spectrophotometric method First Edition
Rubber Seals - Joint Rings for Water Supply, Drainage and Sewerage Pipelines - Specification for Materials Third Edition; Corrected
ISO
4633
Version: 04/01/2004
Rubber, Vulcanized - Preformed Compression Seals for Use Between Concrete Motorway Paving Sections - Specification for
ISO
4635
Material First Edition
ISO
4637
Rubber-Coated Fabrics - Determination of Rubber-to-Fabric Adhesion - Direct Tension Method First Edition
ISO
4638
Polymeric Materials, Cellular Flexible - Determination of Air Flow Permeability First Edition
ISO
4641
Rubber hoses and hose assemblies for water suction and discharge - Specification Third Edition
ISO
4642
Rubber Products - Hoses, Non-Collapsible, for Fire-Fighting Service First Edition
ISO
4643
Moulded Plastics Footwear - Lined or Unlined Poly (Vinyl Chloride) Boots for General Industrial Use - Specification Second Edition
Rubber and Rubber Products - Guide to the Identification of Antidegradants - Thin Layer Chromatographic Methods First Edition;
ISO
4645
Corrigendum 1: 1991
ISO
4646
Rubber- or Plastics-Coated Fabrics - Low-Temperature Impact Test Second Edition
ISO
4647
Rubber, Vulcanized - Determination of Static Adhesion to Textile Cord - H-Pull Test First Edition
Rubber, Vulcanized or Thermoplastic - Determination of Abrasion Resistance Using a Rotating Cylindrical Drum Device Second
ISO
4649
Edition
ISO
4650
Rubber - Identification - Infrared spectrometric method Second Edition
ISO
4651
Cellular rubbers and plastics Determination of dynamic cushioning performance Second Edition; Amendment 1: 09/15/2006
Rubber Compounding Ingredients - Carbon Black - Determination of Specific Surface Area by Nitrogen Adsorption Methods - Part 1:
ISO
4652-1
Single-Point Procedures First Edition
ISO
4655
Rubber - Reinforced Styrene-Butadiene Latex - Determination of Total Bound Styrene Content Second Edition
Rubber compounding ingredients ù Carbon black ù Determination of oil absorption number (OAN) and oil absorption number of
ISO
4656
compressed sample (COAN) First Edition [Replaced: ISO 4656-1, ISO 4656-2, ISO 6894]
ISO
4658
Acrylonitrile-Butadiene Rubber (NBR) - Evaluation Procedure Third Edition; Amendment 1:10/15/2004
ISO
4659
Syrene-Butadiene Rubber (Carbon Black or Carbon Black and Oil Masterbatches) - Evaluation Procedure Fifth Edition
ISO
4660
Rubber, Raw Natural - Colour Index Test Third Edition
ISO
4661-2
Rubber, Vulcanized - Preparation of Samples and Test Pieces - Part 2: Chemical Tests First Edition
ISO
4662
Rubber - Determination of Rebound Resilience of Vulcanizates Second Edition
ISO
4664-1
Rubber, vulcanized or thermoplastic Determination of dynamic properties Part 1: General guidance First edition
Rubber, vulcanized or thermoplastic Determination of dynamic properties Part 1: General guidance First Edition;:1986 [Replaced:
ISO
4664-2
ISO 4663]
ISO
4665
Rubber, Vulcanized and Thermoplastic - Resistance to Weathering Second Edition
Rubber, Vulcanized - Determination of Temperature Rise and Resistance to Fatigue in Flexometer Testing - Part 1: Basic Principles
ISO
4666-1
First Edition
Rubber, Vulcanized - Determination of Temperature Rise and Resistance to Fatique in Flexometer Testing - Part 2: Rotary
ISO
4666-2
Flexometer First Edition
Rubber, Vulcanized - Determination of Temperature Rise and Resistance to Fatigue in Flexometer Testing - Part 3: Compression
ISO
4666-3
Flexometer First Edition
ISO
4671
Rubber and Plastics Hose and Hose Assemblies - Methods of Measurement of Dimensions Second Edition
ISO
4672
Rubber and Plastics Hoses - Sub-Ambient Temperature Flexibility Tests Third Edition
ISO
4674-1
Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods First Edition
ISO
4674-2
Rubber- or Plastics-Coated Fabrics - Determination of Tear Resistance - Part 2: Ballistic Pendulum Method First Edition
ISO
4675
Rubber- or Plastics-Coated Fabrics - Low-Temperature Bend Test Second Edition
ISO
4677-1
Atmospheres for Conditioning and Testing - Determination of Relative Humidity - Part 1: Aspirated Psychrometer Method First Edition
ISO
4677-2
Atmospheres for Conditioning and Testing - Determination of Relative Humidity - Part 2: Whirling Psychrometer Method First Edition
ISO
4683-1
Raw Sheep Skins - Part 1: Descriptions of Defects First Edition
ISO
4683-2
Raw Sheep Skins - Part 2: Designation and Presentation First Edition
ISO
4684
Leather - Chemical Tests - Determination of Volatile Matter First Edition
ISO
4687-1
Iron Ores - Determination of Phosphorus Content - Part 1: Molybdenum Blue Spectrophotometric Method First Edition
ISO
4688-1
Iron Ores - Determination of Aluminium Content - Part 1: Flame Atomic Absorption Spectrometric Method Second Edition
ISO
4689
Iron Ores - Determination of Sulfur Content - Barium Sulfate Gravimetric Method First Edition
ISO
4689-2
Iron ores Determination of sulfur content Part 2: Combustion/titration method First Edition [Cancelled: ISO 4690]
ISO
4689-3
Iron ores Determination of sulfur content Part 3: Combustion/infrared method First Edition [Cancelled: ISO 4690]
ISO
4691
Iron Ores - Determination of Titanium Content - Diantipyrylmethane Spectrophotometric Method First Edition
ISO
4694
Iron Ores - Determination of Fluorine Content - Ion-Selective Electrode Method First Edition
ISO
4695
Iron Ores - Determination of Reducibility Second Edition
Iron Ores - Static Test for Low-Temperature Reduction-Disintegration - Part 1: Reaction with CO, CO2 and H2 First Edition; Cancels
ISO
4696-1
and Replaces 4696
ISO
4696-2
Iron Ores - Static Test for Low-Temperature Reduction-Disintegration - Part 2: Reaction with CO First Edition
ISO
4698
Iron Ore Pellets - Determination of Relative Free-Swelling Index First Edition
ISO
4700
Iron ore pellets for blast furnace and direct reduction feedstocks ù Determination of the crushing strength Third edition
ISO
4701
Iron Ores - Determination of Size Distribution by Sieving Second Edition
Test Conditions for Surface Grinding Machines with Two Columns - Machines for Grinding Slideways - Testing of Accuracy Third
ISO
4703
Edition
ISO
4704
Glass Plant, Pipeline and Fittings - Glass Plant Components First Edition; (Erratum-1979)
ISO
4706
Refillable Welded Steel Gas Cylinders First Edition; (PNS 03: 1992)
ISO
4707
Cork - Stoppers - Sampling for Inspection of Dimensional Characteristics First Edition
ISO
4708
Composition Cork - Gasket Material - Test Methods Second Edition
ISO
4709
Composition Cork - Gasket Material - Classification System, Requirements, Sampling, Packaging and Marking Second Edition
ISO
4710
Cork - Cylindrical Stoppers for Sparkling Wines and Gasified Wines - Characteristics Second Edition
ISO
4711
Agglomerated Cork Discs - Specifications First Edition
ISO
4714
Composition Cork - Specifications, Sampling, Packaging and Marking Second Edition
ISO
4715
Essential Oils - Quantitative Evaluation of Residue on Evaporation First Edition
ISO
4716
Oil of Vetiver (Vetiveria Zizanioides (L.) Nash) Second Edition
ISO
4718
Oil of Lemongrass [Cymbopogon Flexuosus (Nees ex Steudel) J.F. Watson] Second Edition
ISO
4719
Oil of Spike Lavender (Lavandula Latifolia (L.f.) Medikus), Spanish Type Second Edition
ISO
4720
Essential Oils - Nomenclature First Edition Second Edition
ISO
4724
Oil of cedarwood, Virginian (Juniperus virginiana L.) Second Edition
ISO
4725
Oil of Cedarwood, Texas (Juniperus Mexicana Schiede) Second Edition
ISO
4727
Oil of Palmarosa (Cymbopogon Martinii (Roxburgh) W. Watson Var. Motia) First Edition
ISO
4728
Oil of Spanish Wild Margoram (Thumus Mastichina L.) Second Edition
ISO
4729
Oil of Pimento Leaf (Pimenta Dioica (Linnaeus) Merrill) First Edition
ISO
4730
Oil of Melaleuca, Terpinen-4-ol Type (Tea Tree Oil) Second Edition
ISO
4731
Oil of geranium (Pelargonium X ssp.) Second Edition
ISO
4733
Oil of cardamom [Elettaria cardamomum (L.) Maton] Second Edition
ISO
4735
Oils of Citrus - Determination of CD Value by Ultraviolet Spectrophotometric Analysis Second Edition
ISO
4736
Fire Tests - Small Chimneys - Testing at Elevated Temperatures First Edition
Wrought Copper and Copper Alloy Products - Selection and Preparation of Specimens and Test Pieces for Mechanical Testing First
ISO
4739
Edition
ISO
4740
Copper and Copper Alloys - Determination of Zinc Content - Flame Atomic Absorption Spectrometric Method First Edition
ISO
4741
Copper and Copper Alloys - Determination of Phosphorus Content - Molybdovanadate Spectrometric Method First Edition
ISO
4742
Copper Alloys - Determination of Nickel Content - Gravimetric Method First Edition
ISO
4743
Copper Alloys - Determination of Nickel Content - Titrimetric Method First Edition
ISO
4744
Copper and Copper Alloys - Determination of Chromium Content - Flame Atomic Absorption Spectrometric Method First Edition
ISO
4746
Oxygen-Free Copper - Scale Adhesion Test First Edition
ISO
4748
Copper Alloys - Determination of Iron Content - Na2EDTA Titrimetric Method First Edition
ISO
4749
Copper Alloys - Determination of Lead Content - Flame Atomic Absorption Spectrometric Method First Edition
ISO
4751
Copper and Copper Alloys - Determination of Tin Content - Spectrometric Method First Edition
ISO
4753
Fasteners - Ends of Parts with External ISO Metric Thread Second Edition
ISO
4755
Fasteners - Thread Undercuts for External Metric ISO Threads First Edition
ISO
4757
Cross Recesses for Screws First Edition
ISO
4759-1
Tolerances for Fasteners - Part 1: Bolts, Screws Studs and Nuts - Product Grades A, B and C Second Edition
ISO
4759-3
Tolerances for Fasteners - Part 3: Plain Washers for Bolts, Screws and Nuts - Product Grades A and C Third Edition
ISO
4762
Hexagon socket head cap screws Fourth Edition
ISO
4766
Slotted Set Screws with Flat Point First Edition; (NZS/ISO 4766: 1983)
Hexagon Nuts for High-Strength Structural Bolting with Large Width Across Flats - Product Grade B - Property Classes 8 and 10 First
ISO
4775
Edition
ISO
4778
Chain Slings of Welded Construction - Grades M (4), S (6) and T (8) First Edition
ISO
4779
Forged Steel Lifting Hooks with Point and Eye for Use with Steel Chains of Grade M(4) First Edition
ISO
4782
Metal Wire for Industrial Wire Screens and Woven Wire Cloth Second Edition
Industrial Wire Screens and Woven Wire Cloth - Guide to the Choice of Aperture Size and Wire Diameter Combinations - Part 1:
ISO
4783-1
Generalities Second Edition
Industrial Wire Screens and Woven Wire Cloth - Guide to the Choice of Aperture Size and Wire Diameter Combinations - Part 2:
ISO
4783-2
Preferred Combinations for Woven Wire Cloth Second Edition
Industrial Wire Screens and Woven Wire Cloth - Guide to the Choice of Aperture Size and Wire Diameter Combinations - Part 3:
ISO
4783-3
Preferred Combinations for Pre-Crimped or Pressure-Welded Wire Screens First Edition
ISO
4785
Laboratory Glassware - Straight-Bore Glass Stopcocks for General Purposes First Edition
ISO
4786
Enclosed-Scale Adjustable-Range Thermometers First Edition
ISO
4787
Laboratory Glassware - Volumetric Glassware - Methods for Use and Testing of Capacity First Edition
ISO
4788
Laboratory glassware - Graduated measuring cylinders Second edition
ISO
4790
Glass-to-Glass Sealings - Determination of Stresses First Edition
Laboratory Apparatus - Vocabulary Relating to Apparatus Made Essentially from Glass, Porcelain or Vitreous Silica - Part 1: Names
ISO
4791-1
for Items of Apparatus First Edition
ISO
4793
Laboratory Sintered (Fritted) Filters - Porosity Grading, Classification and Designation First Edition
Laboratory Glassware - Methods for Assessing Chemical Resistance of Enamels Used for Colour Coding and Colour Marking First
ISO
4794
Edition
ISO
4795
Glass for Thermometer Bulbs First Edition
ISO
4796-1
Laboratory Glassware - Bottles - Part 1: Screw-Neck Bottles First Edition
ISO
4796-2
Laboratory Glassware - Bottles - Part 2: Conical Neck Bottles First Edition
ISO
4796-3
Laboratory Glassware - Bottles - Part 3: Aspirator Bottles First Edition
ISO
4797
Laboratory glassware Boiling flasks with conical ground joints Second Edition
ISO
4798
Laboratory Glassware - Filter Funnels First Edition
ISO
4799
Laboratory Glassware - Condensers First Edition
ISO
4800
Laboratory Glassware - Separating Funnels and Dropping Funnels Second Edition
ISO
4801
Glass Alcoholometers and Alcohol Hydrometers Not Incorporating a Thermometer First Edition; (Erratum-1980)
Glassware - Hydrolytic Resistance of the Interior Surfaces of Glass Containers - Part 1: Determination by Titration Method and
ISO
4802-1
Classification First Edition
Glassware - Hydrolytic Resistance of the Interior Surfaces of Glass Containers - Part 2: Determination by Flame Spectrometry and
ISO
4802-2
Classification First Edition
ISO
4803
Laboratory Glassware - Borosilicate Glass Tubing First Edition
ISO
4805
Laboratory Glassware - Thermo-Alcoholometers and Alcohol- Thermohydrometers First Edition
ISO
4814
Household Sewing Machines - Determination of Stability of Needle Thread Tension First Edition
ISO
4815
Household Sewing Machines - Determination of Sewing Capacity First Edition
ISO
4817
Household Sewing Machines - Determination of Directional Stability (Drift) First Edition
ISO
4818
Household Sewing Machines - Determination of Creep of One Ply of Material over Another First Edition
ISO
4819
Household Sewing Machines - Determination of Reproducibility of Stitch Length Setting First Edition
ISO
4823 AMD 1
Dentistry ù Elastomeric impression materials AMENDMENT 1 Third Edition
ISO
4823 CORR 1
Dentistry ù Elastomeric impression materials TECHNICAL CORRIGENDUM 1 Third Edition
ISO
4823
Dentistry - Elastometric Impression Materials Third Edition
Steel and Cast Iron - Determination of Total Silicon Content - Reduced Molybdosilicate Spectrophotometric Method - Part 1: Silicon
ISO
4829-1
Contents Between 0,05 and 1,0 % First Edition; (CEN EN 24 829 Part 1: 1990)
Steel and Iron - Determination of Total Silicon Content - Reduced Molybdosilicate Spectrophotometric Method - Part 2: Silicon
ISO
4829-2
Contents Between 0,01 and 0,05% First Edition; (CEN EN 24 829 Part 2: 1990)
Microbiology of food and animal feeding stuffs Horizontal method for the detection and enumeration of coliforms Most probable
ISO
4831
number technique Third Edition;: 1986 [Replaced: ISO 5541-2]
Microbiology of food and animal feeding stuffs Horizontal method for the enumeration of coliforms Colony-count technique Third
ISO
4832
Edition; Supersedes ISO 5541-1: 1986
Microbiology of Food and Animal Feeding Stuffs - Horizontal Method for the Enumeration of Microorganisms - Colony-Count
ISO
4833
Technique at 30 Degrees Celcius Third Edition
|
||
|
|
|