|
|
Org
Doc #
Title
Geometrical Product Specifications (GPS) - Standard Reference Temperature for Geometrical Product Specification and Verification
ISO
1
Second Edition
ISO
2
Textiles - Designation of the Direction of Twist in Yarns and Related Products First Edition
ISO
3
Preferred Numbers - Series of Preferred Numbers First Edition; PNS 399: 1991
ISO
4
Information and Documentation - Rules for the Abbreviation of Title Words and Titles of Publications Third Edition
Photography - Density Measurements - Part 1: Terms, Symbols and Notations Photgraphie - Mesurage des densites - Partie 1:
ISO
5-1
Termes, symboles et notations First Edition
ISO
5-2
Photography - Density Measurements - Part 2: Geometric Conditions for Transmission Density Fourth Edition
ISO
5-3
Photography - Density Measurements - Part 3: Spectral Conditions Second Edition
ISO
5-4
Photography - Density Measurements - Part 4: Geometric Conditions for Reflection Density Second Edition
ISO
6
Photography - Black-and-White Pictorial Still Camera Negative Film/Process Systems - Determination of ISO Speed Second Edition
ISO
7-1 CORR 1
Pipe Threads Where Pressure-Tight Joints Are Made on the Threads - Part 1: Dimensions, Tolerances and Designation Third Edition
ISO
7-1
Pipe Threads Where Pressure-Tight Joints Are Made on the Threads - Part 1: Dimensions, Tolerances and Designation Third Edition
ISO
7-2
Pipe Threads Where Pressure-Tight Joints Are Made on the Threads - Part 2: Verification by Means of Limit Gauges Second Edition
ISO
8
Documentation - Presentation of Periodicals First Edition; Erratum-1979
Information and Documentation - Transliteration of Cyrillic Characters into Latin Characters - Slavic and Non-Slavic Languages
ISO
9
Second Edition
ISO
11
Aircraft - Ground Pressure Testing Connections for Pressure Cabins Second Edition
Straight-Sided Splines for Cylindrical Shafts with Internal Centering - Dimensions, Tolerances and Verification Second Edition; JIS B
ISO
14
1601:1996
ISO
15
Rolling Bearings - Radial Bearings - Boundary Dimensions, General Plan Second Edition
ISO
16
Acoustics - Standard Tuning Frequency (Standard Musical Pitch) First Edition (NZS/ISO 16: 1975) First Edition; NZS/ISO 16: 1975
ISO
17
Guide to the Use of Preferred Numbers and of Series of Preferred Numbers First Edition; PNS 400: 1991
ISO
18
Documentation - Contents List of Periodicals First Edition
ISO
21
Shipbuilding - Inland Navigation - Cable-Lifters for Stud-Link Anchor Chains Second Edition
ISO
22
Belt Drives - Flat Transmission Belts and Corresponding Pulleys - Dimensions and Tolerances Second Edition
ISO
23
Cinematography - Camera Usage of 35 mm Motion-Picture Film - Specifications Second Edition
ISO
25
Cinematography - Camera Usage of 16 mm Motion-Picture Film - Specifications Second Edition
ISO
26
Cinematography - Projector Usage of 16 mm Motion-Picture Films for Direct Front Projection - Specifications Third Edition
ISO
28
Cinematography - Camera Usage of 8 mm Type R Motion-Picture Film - Specifications First Edition
ISO
31-0
Quantities and Units - Part 0: General Principles Third Edition; Amendment 1: 12/15/1998; Amendment 2: 10/1/2005
Quantities and Units - Part 5: Electricity and Magnetism Second Edition; Corrected and Reprinted: 05/15/1993; Amendment 1:
ISO
31-5
12/15/1998
ISO
31-6
Quantities and Units - Part 6: Light and Related Electromagnetic Radiations Third Edition; Amendment 1: 12/15/1998
ISO
31-8
Quantities and Units - Part 8: Physical Chemistry and Molecular Physics Third Edition; Amendment 1: 12/15/1998
ISO
31-9
Quantities and Units - Part 9: Atomic and Nuclear Physics Third Edition; Amendment 1: 12/15/1998
ISO
31-10
Quantities and Units - Part 10: Nuclear Reactions and Ionizing Radiations Third Edition; Amendment 1: 12/15/1998
ISO
31-11
Quantities and Units - Part 11: Mathematical Signs and Symbols for Use in the Physical Sciences and Technology Second Edition
ISO
31-12
Quantities and Units - Part 12: Characteristic Numbers Third Edition; Amendment 1: 12/15/1998
ISO
31-13
Quantities and Units - Part 13: Solid State Physics Third Edition; Amendment 1: 12/15/1998
ISO
32
Gas Cylinders for Medical Use - Marking for Identification of Content First Edition; Erratum-1979
ISO
34-1
Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces Second Edition
ISO
34-2
Rubber, vulcanized or thermoplastic ù Determination of tear strength ù Part 2: Small (Delft) test pieces Second Edition
ISO
35 AMD 1
Natural rubber latex concentrate ù Determination of mechanical stability AMENDMENT 1: Precision data Fifth Edition
ISO
35
Natural rubber latex concentrate ù Determination of mechanical stability Fifth Edition
ISO
36
Rubber, Vulcanized or Thermoplastic - Determination of Adhesion to Textile Fabric Fourth Edition
ISO
37
Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties Fourth Edition
ISO
43
Aircraft - Jacking Pads First Edition
ISO
44
Aerospace - Lever-Operated, Two-Position, ON/OFF Switches - Directions of Operation First Edition
ISO
45
Aircraft - Pressure Refuelling Connections Second Edition
ISO
46
Aircraft - Fuel Nozzle Grounding Plugs and Sockets First Edition
ISO
48
Rubber, vulcanized or thermoplastic ù Determination of hardness (hardness between 10 IRHD and 100 IRHD) Fourth Edition
ISO
49
Malleable Cast Iron Fittings Threaded to ISO 7-1 Second Edition; Corrigendum 1 02/15/1997
ISO
53
Cylindrical Gears for General and Heavy Engineering - Standard Basic Rack Tooth Profile Second Edition
ISO
54
Cylindrical Gears for General Engineering and for Heavy Engineering - Modules Second Edition
ISO
60
Plastics - Determination of Apparent Density of Material That Can Be Poured from a Specified Funnel Second Edition
ISO
61
Plastics - Determination of Apparent Density of Moulding Material That Cannot Be Poured from a Specified Funnel First Edition
ISO
62
Plastics - Determination of Water Absorption Second Edition
ISO
65
Carbon Steel Tubes Suitable for Screwing in Accordance with ISO 7/1 Second Edition
ISO General Purpose Screw Threads - Basic Profile Part 1: Metric Screw Threads First Edition; This Standard Together with ISO 68-
ISO
68-1
2 Cancels and Replaces ISO 68
ISO General Purpose Screw Threads - Basic Profile Part 2: Inch Screw Threads First Edition; This Standard Together with ISO 68-1
ISO
68-2
Cancels and Replaces ISO 68
ISO
69
Cinematography - 16 mm Motion-Picture and Magnetic Film - Cutting and Perforating Dimensions Third Edition
Cinematography - Monophonic 35 mm Negative Photographic Sound Record on 35 mm Motion-Picture Film - Position and Maximum
ISO
70
Width Dimensions Second Edition
Cinematography - 16 mm Negative Photographic Sound Record on 16 mm, 35/16 mm and 35/32 mm Motion-Picture Film - Positions
ISO
71
and Dimensions First Edition
Cinematography - Image Area Produced by Camera Aperture and Maximum Projectable Image Area on 8 mm Type R Motion-Picture
ISO
74
Film - Positions and Dimensions First Edition
ISO
75-1
Plastics - Determination of Temperature of Deflection under Load - Part 1: General Test Method Second Edition
Plastics - Determination of Temperature of Deflection under Load - Part 2: Plastics and Ebonite Second Edition [Superseded By: JSA
ISO
75-2
JIS K 7191-2, JSA JIS K 7191-2]
Plastics - Determination of Temperature of Deflection under Load - Part 3: High Strength Thermosetting Laminates and Long-Fibre-
ISO
75-3
Reinforced Plastics Second Edition
ISO
76
Rolling Bearings - Static Load Ratings Third Edition
ISO
78-2
Chemistry - Layouts for Standards - Part 2: Methods of Chemical Analysis Second Edition
ISO
78-3
Chemistry - Layouts for Standards - Part 3: Standard for Molecular Absorption Spectrometry First Edition
ISO
78-4
Layouts for Standards - Part 4: Standard for Atomic Absorption Spectrometric Analysis First Edition
ISO
90-1
Light Gauge Metal Containers - Definitions and Determination of Dimensions and Capacities - Part 1: Open-Top Cans Second Edition
Light Gauge Metal Containers - Definitions and Determination of Dimensions and Capacities - Part 2: General Use Containers
ISO
90-2
Second Edition
ISO
90-3
Light Gauge Metal Containers - Definitions and Determination of Dimensions and Capacities - Part 3: Aerosol Cans Second Edition
Petroleum Measurement Tables - Part 1: Tables Based on Reference Temperatures of 15 Degrees C and 60 Degrees F Second
ISO
91-1
Edition
ISO
91-2
Petroleum Measurement Tables - Part 2: Tables Based on a Reference Temperature of 20 Degrees C First Edition
ISO
92
Textile Machinery and Accessories - Spinning Machinery - Definition of Side (Left or Right) First Edition
ISO
93-1
Textile Machinery and Accessories - Cylindrical Sliver Cans - Part 1: Main Dimensions Fourth Edition
ISO
93-2
Textile Machinery and Accessories - Cylindrical Sliver Cans - Part 2: Spring Bottoms Third Edition
ISO
94
Textile Machinery and Accessories - Spindle Gauges for Ring-Spinning and Ring-Doubling Frames Second Edition
Textile Machinery and Accessories - Rings and Travellers for Ring Spinning and Ring Doubling Frames - Part 1: T-Rings and Their
ISO
96-1
Appropriate Travellers First Edition
Textile Machinery and Accessories - Rings and Travellers for Ring Spinning and Ring Doubling Frames - Part 2: HZCH-, HZ- and J-
ISO
96-2
Rings and Their Appropriate Travellers First Edition
Textile Machinery and Accessories - Spinning Preparatory and Spinning Machinery - Main Dimensions of Coverings for Top Rollers
ISO
98
Third Edition
ISO
102
Aircraft - Gravity Filling Orifices Second Edition
ISO
104
Rolling Bearings - Thrust Bearings - Boundary Dimensions, General Plan Third Edition
Textiles - Tests for Colour Fastness - Part A01: General Principles of Testing Fifth Edition; CEN EN 20105-A03: 1994; CEN EN ISO
ISO
105-A01
105-A01: 1995; CEN EN 20105-A03: 1994; CEN EN ISO 105-A01: 1995
ISO
105-A02
Textiles - Tests for Colour Fastness - Part A02: Grey Scale for Assessing Change in Colour Fourth Edition; Corrigendum 2: 10/1/2005
ISO
105-A03
Textiles - Tests for Colour Fastness - Part A03: Grey Scale for Assessing Staining Fourth Edition; Corrigendum 2: 10/1/2005
Textiles - Tests for Colour Fastness - Part A04: Method for the Instrumental Assessment of the Degree of Staining of Adjacent
ISO
105-A04
Fabrics First Edition
Textiles - Tests for Colour Fastness - Part A05: Instrumental Assessment of Change in Colour for Determination of Grey Scale Rating
ISO
105-A05
First Edition; Corrigendum 1 02/15/1997
ISO
105-A06
Textiles - Tests for Colour Fastness - Part A06: Instrumental Determination of 1/1 Standard Depth of Colour First Edition
ISO
105-A08
Textiles - Tests for Colour Fastness - Part A08: Vocabulary Used in Colour Measurement First Edition
ISO
105-B01
Textiles - Tests for Colour Fastness - Part B01: Colour Fastness to Light: Daylight Fifth Edition; Amendment 1-1998
Textiles - Tests for Colour Fastness - Part B02: Colour Fastness to Artificial Light: Xenon Arc Fading Lamp Test Fourth Edition;
ISO
105-B02
Amendment 1-1998; Amendment 2-2000
ISO
105-B03
Textiles - Tests for Colour Fastness - Part B03: Colour Fastness to Weathering: Outdoor Exposure Fourth Edition
ISO
105-B04
Textiles - Tests for Colour Fastness - Part B04: Colour Fastness to Artificial Weathering: Xenon Arc Fading Lamp Test Fourth Edition
Textiles - Tests for Colour Fastness - Part B05: Detection and Assessment of Photochromism Fourth Edition; CEN EN ISO 105-B05:
ISO
105-B05
1995
Textiles - Tests for Colour Fastness - Part B06: Colour Fastness and Ageing to Artificial Light at High Temperatures: Xenon Arc
ISO
105-B06
Fading Lamp Test Second Edition; Amendment 1: 09/01/2002
ISO
105-B08
Textiles - Tests for Colour Fastness - Part B08: Quality Control of Blue Wool Reference Materials 1 to 7 First Edition
Textiles - Tests for Colour Fastness - Part C06: Colour Fastness to Domestic and Commercial Laundering Third Edition; Technical
ISO
105-C06
Corrigendum 1: 02/01/2002; Technical Corrigendum 2: 5/15/2002
ISO
105-C07
Textiles - Tests for Colour Fastness - Part C07: Colour Fastness to Wet Scrubbing of Pigment Printed Textiles First Edition
Textiles - Tests for Colour Fastness - Part C08: Colour Fastness to Domestic and Commercial Laundering Using a Non-Phosphate
Reference Detergent Incorporating a Low Temperature Bleach Activator First Edition; Technical Corrigendum 1: 5/15/2002;
ISO
105-C08
Amendment 1: 5/15/2006
Textiles - Tests for Colour Fastness - Part C09: Colour Fastness to Domestic and Commercial Laundering - Oxidative Bleach
Response Using a Non-Phosphate Reference Detergent Incorporating a Low Temperature Bleach Activator First Edition; Technical
ISO
105-C09
Corrigendum 1: 5/15/2002; Amendment 1: 12/01/2003
ISO
105-C10
Textiles Tests for colour fastness Part C10: Colour fastness to washing with soap or soap and soda First Edition;: 1989
ISO
105-C12 CORR 1
Textiles ù Tests for colour fastness ù Part C12: Colour fastness to industrial laundering TECHNICAL CORRIGENDUM 1 First Edition
ISO
105-C12
Textiles Tests for colour fastness Part C12: Colour fastness to industrial laundering First Edition
ISO
105-D01
Textiles - Tests for Colour Fastness - Part D01: Colour Fastness to Dry Cleaning Fourth Edition; CEN EN ISO 105-D01: 1995
Textiles - Tests for Colour Fastness - Part D02: Colour Fastness to Rubbing: Organic Solvents Fourth Edition; CEN EN ISO 105-D02:
ISO
105-D02
1995
Textiles - Tests for Colour Fastness - Part E01: Colour Fastness to Water Fourth Edition; Technical Corrigendum 1: 02/01/2002; CEN
ISO
105-E01
EN ISO 105-E01: 1996
Textiles - Tests for Colour Fastness - Part E02: Colour Fastness to Sea Water Fourth Edition; Technical Corrigendum 1: 02/01/2002;
ISO
105-E02
CEN EN ISO 105-E02: 1996
Textiles - Tests for Colour Fastness - Part E03: Colour Fastness to Chlorinated Water (Swimming-Pool Water) Third Edition; CEN EN
ISO
105-E03
ISO 105-E03: 1996
Textiles - Tests for Colour Fastness - Part E04: Colour Fastness to Perspiration Fourth Edition; Technical Corrigendum 1:
ISO
105-E04
02/01/2002; CEN EN ISO 105-E04: 1996
ISO
105-E05
Textiles - Tests for Colour Fastness - Part E05: Colour Fastness to Spotting: Acid Fourth Edition
ISO
105-E06
Textiles Tests for colour fastness Part E06: Colour fastness to spotting: Alkali Fourth Edition
Textiles - Tests for Colour Fastness - Part E07: Colour Fastness to Spotting: Water Third Edition; Technical Corrigendum 1:
ISO
105-E07
02/01/2002
ISO
105-E08
Textiles - Tests for Colour Fastness - Part E08: Colour Fastness to Hot Water Third Edition; CEN EN ISO 105-E08: 1996
ISO
105-E09
Textiles - Tests for Colour Fastness - Part E09: Colour Fastness to Potting Third Edition; Technical Corrigendum 1: 02/01/2002
ISO
105-E10
Textiles - Tests for Colour Fastness - Part E10: Colour Fastness to Decatizing Third Edition; CEN EN ISO 105-E10: 1996
ISO
105-E11
Textiles - Tests for Colour Fastness - Part E11: Colour Fastness to Steaming Third Edition
Textiles - Tests for Colour Fastness - Part E12: Colour Fastness to Milling: Alkaline Milling Third Edition; Technical Corrigendum 1:
ISO
105-E12
02/01/2002; Amendment 1: 11/15/2002
ISO
105-E13
Textiles - Tests for Colour Fastness - Part E13: Colour Fastness to Acid-Felting: Severe Third Edition; Corrigendum 1: 06/01/1999
ISO
105-E14
Textiles - Tests for Colour Fastness - Part E14: Colour Fastness to Acid-Felting: Mild Third Edition
ISO
105-E16
Textiles Tests for colour fastness Part E16: Colour fastness to water spotting on upholstery fabrics First Edition
ISO
105-F
Textiles - Tests for Colour Fastness - Part F: Standard Adjacent Fabrics Third Edition
ISO
105-F01
Textiles - Tests for Colour Fastness - Part F01: Specification for Wool Adjacent Fabric First Edition
ISO
105-F03
Textiles - Tests for Colour Fastness - Part F03: Specification for Polyamide Adjacent Fabric First Edition
ISO
105-F04
Textiles - Tests for Colour Fastness - Part F04: Specification for Polyester Adjacent Fabric First Edition
ISO
105-F05
Textiles - Tests for Colour Fastness - Part F05: Specification for Acrylic Adjacent Fabric First Edition
ISO
105-F06
Textiles - Tests for Colour Fastness - Part F06: Specification for Silk Adjacent Fabric First Edition
ISO
105-F07
Textiles - Tests for Colour Fastness - Part F07: Specification for Secondary Acetate Adjacent Fabric First Edition
ISO
105-F10
Textiles - Tests for Colour Fastness - Part F10: Specification for Adjacent Fabric: Multifibre First Edition
Textiles - Tests for Colour Fastness - Part G01: Colour Fastness to Nitrogen Oxides Second Edition; Corrigendum 1-1995; CEN EN
ISO
105-G01
ISO 105-G01: 1995
ISO
105-G02
Textiles - Tests for Colour Fastness - Part G02: Colour Fastness to Burnt-Gas Fumes Second Edition; Corrigendum 1-1995
ISO
105-G03
Textiles - Tests for Colour Fastness - Part G03: Colour Fastness to Ozone in the Atmosphere Second Edition
Textiles - Tests for Colour Fastness Part G04: Colour Fastness to Oxides of Nitrogen in the Atmosphere at High Humidities First
ISO
105-G04
Edition
ISO
105-J01
Textiles - Tests for Colour Fastness - Part J01: General Principles for Measurement of Surface Colour Fourth Edition
Textiles - Tests for Colour Fastness - Part J02: Instrumental Assessment of relative Whiteness Second Edition; Technical
ISO
105-J02
Corrigendum 1-1998
Textiles Tests for colour fastness Part J03: Calculation of colour differences First Edition; Technical Corrigendum 1: 06/01/1996;
ISO
105-J03
Technical Corrigendum 2: 04/01/2006
Textiles ù Tests for colour fastness ù Part J05: Method for the instrumental assessment of the colour inconstancy of a specimen with
ISO
105-J05
change in illuminant (CMCCON02 First Edition
Textiles - Tests for Colour Fastness - Part N01: Colour Fastness to Bleaching: Hypochlorite Second Edition; DIN EN 20105-N01:
ISO
105-N01
1995
ISO
105-N02
Textiles - Tests for Colour Fastness - Part N02: Colour Fastness to Bleaching: Peroxide Second Edition; CEN EN ISO 105-N02: 1995
Textiles - Tests for Colour Fastness - Part N03: Colour Fastness to Bleaching: Sodium Chlorite (Mild) Second Edition; CENELEC EN
ISO
105-N03
ISO 105-N04: 1995
ISO
105-N04
Textiles - Tests for Colour Fastness - Part N04: Colour Fastness to Bleaching: Sodium Chlorite (Severe) Second Edition
ISO
105-N05
Textiles - Tests for Colour Fastness - Part N05: Colour Fastness to Stoving Second Edition; CEN EN ISO 105-N05: 1995
Textiles - Tests for Colour Fastness - Part P01: Colour Fastness to Dry Heat (Excluding Pressing) Second Edition; CEN EN ISO 105-
ISO
105-P01
P01: 1995
ISO
105-P02
Textiles - Tests for colour fastness - Part P02: Colour fastness to pleating: Steam pleating Third Edition
Textiles - Tests for Colour Fastness - Part S01: Colour Fastness to Vulcanization: Hot Air Second Edition; CEN EN ISO 105-S01:
ISO
105-S01
1995
Textiles - Tests for Colour Fastness - Part S02: Colour Fastness to Vulcanization: Sulfur Monochloride Second Edition; CEN EN ISO
ISO
105-S02
105-S02: 1995
Textiles - Tests for Colour Fastness - Part S03: Colour Fastness to Vulcanization: Open Steam Second Edition; CEN EN ISO 105-
ISO
105-S03
S03: 1995
Textiles - Tests for Colour Fastness - Part X01: Colour Fastness to Carbonizing: Aluminium Chloride Fourth Edition; CEN EN ISO
ISO
105-X01
105-X01: 1995
Textiles - Tests for Colour Fastness - Part X02: Colour Fastness to Carbonizing: Sulfuric Acid Fourth Edition; CEN EN ISO 105-X02:
ISO
105-X02
1995
ISO
105-X04
Textiles - Tests for Colour Fastness - Part X04: Colour Fastness to Mercerizing Fourth Edition
ISO
105-X05
Textiles - Tests for Colour Fastness - Part X05: Colour Fastness to Organic Solvents Fourth Edition
ISO
105-X06
Textiles - Tests for Colour Fastness - Part X06: Colour Fastness to Soda Boiling Fourth Edition
ISO
105-X07
Textiles - Tests for Colour Fastness - Part X07: Colour Fastness to Cross-Dyeing: Wool Fourth Edition
ISO
105-X08
Textiles - Tests for Colour Fastness - Part X08: Colour Fastness to Degumming Fourth Edition
ISO
105-X09
Textiles - Tests for Colour Fastness - Part X09: Colour Fastness to Formaldehyde Fourth Edition; CEN EN ISO 105-X09: 1995
Textiles - Tests for Colour Fastness - Part X10: Assessment of Migration of Textile Colours into Polyvinyl Chloride Coatings Fourth
ISO
105-X10
Edition; CEN EN ISO 105-X10: 1995
ISO
105-X11
Textiles - Tests for Colour Fastness - Part X11: Colour Fastness to Hot Pressing Fourth Edition; CEN EN ISO 105-X11: 1996
Textiles - Tests for Colour Fastness - Part X12: Colour Fastness to Rubbing Fifth Edition; Replaces GME 60330 [Replaced: GME
ISO
105-X12
GME 60330]
Textiles - Tests for Colour Fastness - Part X13: Colour Fastness of Wool Dyes to Processes Using Chemical Means for Creasing,
ISO
105-X13
Pleating and Setting Fourth Edition
Textiles - Tests for Colour Fastness - Part X14: Colour Fastness to Acid Chlorination of Wool: Sodium Dichloroisocyanurate Third
ISO
105-X14
Edition
ISO
105-X16
Textiles - Tests for Colour Fastness - Part X16: Colour Fastness to Rubbing - Small Areas First Edition
ISO
105-X18
Textiles ù Tests for colour fastness ù Part X18: Assessment of the potential to phenolic yellowing of materials First Edition
Textiles - Tests for Colour Fastness - Part Z01: Colour Fastness to Metals in the Dye-Bath: Chromium Salts Second Edition; CEN EN
ISO
105-Z01
ISO 105-Z01: 1995
Textiles - Tests for Colour Fastness - Part Z02: Colour Fastness to Metals in the Dye-Bath: Iron and Copper Second Edition; CEN EN
ISO
105-Z02
ISO 105-Z02: 1995
ISO
105-Z03
Textiles - Tests for Colour Fastness - Part Z03: Intercompatibility of Basic Dyes for Acrylic Fibres First Edition
ISO
105-Z04
Textiles - Tests for Colour Fastness - Part Z04: Dispersibility of Disperse Dyes First Edition
ISO
105-Z05
Textiles - Tests for Colour Fastness - Part Z05: Determination of the Dusting Behaviour of Dyes First Edition
ISO
105-Z06
Textiles - Tests for Colour Fastness - Part Z06: Evaluation of Dye and Pigment Migration First Edition
Textiles - Tests for Colour Fastness Part Z07: Determination of Application Solubility and Solution Stability of Water-Soluble Dyes
ISO
105-Z07
First Edition
Textiles - Tests for Colour Fastness Part Z08: Determination of Solubility and Solution Stability of Reactive Dyes in the Presence of
ISO
105-Z08
Electrolytes First Edition
ISO
105-Z09
Textiles - Tests for Colour Fastness Part Z09: Determination of Cold Water Solubility of Water-Soluble Dyes First Edition
ISO
105-Z10
Textiles - Tests for Colour Fastness - Part Z10: Determination of Relative Colour Strength of Dyes in Solution First Edition
ISO
105-Z11
Textiles - Tests for Colour Fastness - Part Z11: Evaluation of Speckiness of Colorant Dispersions First Edition
ISO
108
Textile Machinery and Accessories - Weaving Looms - Definition of Left and Right Sides First Edition
ISO
109
Textile Machinery - Working Widths of Weaving Machines First Edition
ISO
113
Rolling Bearings - Plummer Block Housings - Boundary Dimensions Second Edition
ISO
115
Unalloyed Aluminium Ingots for Remelting - Classification and Composition First Edition
ISO
119
Plastics - Phenol-Formaldehyde Mouldings - Determination of Free Phenols - Iodometric Method First Edition;
Plastics - Phenol-Formaldehyde Mouldings - Determination of Free Ammonia and Ammonium Compounds - Colorimetric Comparison
ISO
120
Method First Edition
ISO
123
Rubber Latex - Sampling Third Edition
ISO
124
Latex, Rubber - Determination of Total Solids Content Fourth Edition; Amendment 1: 2/01/2006
ISO
125
Natural Rubber Latex Concentrate - Determination of Alkalinity Fifth Edition
ISO
126
Natural rubber latex concentrate Determination of dry rubber content Fifth edition
ISO
127
Rubber, Natural Latex Concentrate - Determination of KOH Number Third Edition: Amendment 1: 02/01/2006
ISO
128-1
Technical Drawings - General Principles of Presentation - Part 1: Introduction and Index First Edition
ISO
128-20
Technical Drawings - General Principles of Presentation - Part 20: Basic Conventions for Lines First Edition
ISO
128-21
Technical Drawings - General Principles of Presentation - Part 21: Preparation of Lines by CAD Systems First Edition
Technical Drawings - General Principles of Presentation - Part 22: Basic Conventions and Applications for Leader Lines and
ISO
128-22
Reference Lines First Edition
ISO
128-23
Technical Drawings - General Principles of Presentation - Part 23: Lines on Construction Drawings First Edition
ISO
128-24
Technical Drawings - General Principles of Presentation - Part 24: Lines on Mechanical Engineering Drawings First Edition
ISO
128-25
Technical Drawings - General Principles of Presentation - Part 25: Lines on Shipbuilding Drawings First Edition
Technical Drawings - General Principles of Presentation - Part 30: Basic Conventions for Views First Edition; Cancels and Replaces
ISO
128-30
ISO 128:1982
ISO
128-34
Technical Drawings - General Principles of Presentation - Part 34: Views on Mechanical Engineering Drawings First Edition
ISO
128-40
Technical Drawings - General Principles of Presentation - Part 40: Basic Conventions for Cuts and Sections First Edition
Technical Drawings - General Principles of Presentation - Part 44: Sections on Mechanical Engineering Drawings First Edition;
ISO
128-44
Cancels and Replaces ISO 128:1982
Technical Drawings - General Principles of Presentation - Part 50: Basic Conventions for Representing Areas on Cuts and Sections
ISO
128-50
First Edition; Cancels and Replaces ISO 128:1982
ISO
129-1
Technical drawings Indication of dimensions and tolerances Part 1: General principles First Edition; Supersedes ISO 129
Rubber, vulcanized or thermoplastic - Determination of flex cracking and crack growth (De Mattia) Fourth Edition; Replaces ISO
ISO
132
133:1983
ISO
137
Wool - Determination of Fiber Diameter - Projection Microscope Method First Edition
ISO
139
Textiles - Standard Atmospheres for Conditioning and Testing Second Edition
Acoustics Measurement of sound insulation in buildings and of building elements Part 1: Requirements for laboratory test facilities
with suppressed flanking transmission AMENDMENT 1: Specific requirements on the frame of the test opening for lightweight twin
ISO
140-1
leaf partitions Third Edition; Amendment 1: 12/1/2004
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 2: Determination, Verification and
ISO
140-2
Application of Precision Data Second Edition; CEN EN 20140-2: 1993; Corrigendum-1993
Acoustics Measurement of sound insulation in buildings and of building elements Part 3: Laboratory measurements of airborne
sound insulation of building elements AMENDMENT 1: Installation guidelines for lightweight twin leaf partitions Second Edition;
ISO
140-3
Amendment 1: 12/1/2004
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 4: Field Measurements of Airborne Sound
ISO
140-4
Insulation between Rooms SEcond Edition
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 5: Field Measurements of Airborne Sound
ISO
140-5
Insulation of Facade Elements and Facades Second Edition
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 6: Laboratory Measurements of Impact
ISO
140-6
Sound Insulation of Floors Second Edition
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 7: Field Measurements of Impact Sound
ISO
140-7
Insulation of Floors Second Edition
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 8: Laboratory Measurements of the
ISO
140-8
Reduction of Transmitted Impact Noise by Floor Coverings on a Heavyweight Standard Floor Second Edition
Acoustics - Measurements of Sound Insulation in Buildings and of Building Elements - Part 9: Laboratory Measurement of Room-to-
ISO
140-9
Room Airborne Sound Insulation of a Suspended Ceiling with a Plenum Above It First Edition; CEN EN 20140-9: 1993
Acoustics - Measurement of Sound Insulation in Buildings and of Building Elements - Part 10: Laboratory Measurement of Airborne
ISO
140-10
Sound Insulation of Small Building Elements First Edition
Acoustics - Measurement of sound insulation in buildings and of building elements - Part 11: Laboratory measurements of the
ISO
140-11
reduction of transmitted impact sound by floor coverings on lightweight reference floors First edition
Acoustics Measurement of sound insulation in buildings and of building elements Part 14: Guidelines for special situations in the
ISO
140-14 CORR 1
field First Edition
Acoustics Measurement of sound insulation in buildings and of building elements Part 14: Guidelines for special situations in the
ISO
140-14
field First Edition
Acoustics Measurement of sound insulation in buildings and of building elements Part 16: Laboratory measurement of the sound
ISO
140-16
reduction index improvement by additional lining First Edition
Acoustics Measurement of sound insulation in buildings and of building elements Part 18: Laboratory measurement of sound
ISO
140-18
generated by rainfall on building elements First Edition
ISO
141
Textile Machinery and Accessories - Pirn Winders and Cross Winders - Definition of Left and Right Sides First Edition
ISO
142
Textile Machinery and Accessories - Weaving Preparatory Machines - Definition of Left and Right Sides First Edition
ISO
143
Textile Machinery and Accessories - Weft Pirns for Automatic Looms First Edition
ISO
148-1
Metallic materials Charpy pendulum impact test Part 1: Test method First Edition; Supersedes ISO 148:1983 and ISO 83:1976
Metallic Materials - Charpy Pendulum Impact Test - Part 2: Verification of Test Machines First Edition; Cancels and Replaces ISO/R
ISO
148-2
442: 1965
Metallic Materials - Charpy Pendulum Impact Test - Part 3: Preparation and Characterization of Charpy V Reference Test Pieces for
ISO
148-3
Verification of Test Machines First Edition
ISO
150
Raw, Refined and Boiled Linseed Oil for Paints and Varnishes - Specifications and Methods of Test Second Edition
ISO
155
Belt Drives - Pulleys - Limiting Values for Adjustment of Centres Third Edition
ISO
157
Coal - Determination of Forms of Sulfur Second Edition
ISO
161-1
Thermoplastics Pipes for the Conveyance of Fluids - Nominal Pressures - Part 1: Metric Series Third Edition
Thermoplastics Pipes for the Conveyance of Fluids - Nominal Outside Diameters and Nominal Pressures - Part 2: Inch-Based Series
ISO
161-2
Second Edition
Cinematography - Head Gaps and Sound Records for Three-, Four-, or Six-Track Magnetic Sound Records on 35 mm and Single-
Track on 17,5 mm Motion-Picture Film Containing No Picture - Positions and Width Dimensions Second Edition; Replaces ISO 360:
ISO
162
1975
ISO
171
Plastics - Determination of Bulk Factor of Moulding Materials First Edition
ISO
172
Plastics - Phenol - Formaldehyde Mouldings - Detection of Free Ammonia First Edition
ISO
175
Plastics - Methods of Test for the Determination of the Effects of Immersion in Liquid Chemicals Second Edition
ISO
176
Plastics - Determination of Loss of Plasticizers - Activated Carbon Method Second Edition
ISO
177
Plastics - Determination of Migration of Plasticizers Second Edition
ISO
178
Plastics - Determination of Flexural Properties Fourth Edition; Amendment 1: 02/15/2004
ISO
179-1
Plastics - Determination of Charpy Impact Properties - Part 1: Non-Instrumented Impact Test First Edition; Amendment 1: 7/15/2005
Plastics - Determination of Charpy Impact Properties - Part 2: Instrumented Impact Test First Edition; Technical Corrigendum 1: 11-
ISO
179-2
15-1998
ISO
180
Plastics - Determination of Izod Impact Strength Third Edition; Amendment 1: 12/1/2006
Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to
ISO
182-1
Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 1: Congo Red Method First Edition
Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to
ISO
182-2
Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 2: pH Method First Edition
Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to
ISO
182-3
Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 3: Conductometric Method First Edition
Plastics - Determination of the Tendency of Compounds and Products Based on Vinyl Chloride Homopolymers and Copolymers to
ISO
182-4
Evolve Hydrogen Chloride and Any Other Acidic Products at Elevated Temperatures - Part 4: Potentiometric Method First Edition
ISO
185
Grey Cast Iron - Classification Second Edition
ISO
186
Paper and Board - Sampling to Determine Average Quality Fourth Edition
Paper, Board and Pulps - Standard Atmosphere for Conditioning and Testing and Procedure for Monitoring the Atmosphere and
ISO
187
Conditioning of Samples Second Edition; CEN EN 20187: 1993; PNS 304: 1990
ISO
188
Rubber, Vulcanized or Thermoplastic - Accelerated Ageing and Heat Resistance Tests Fourth Edition
ISO
196
Wrought Copper and Copper Alloys - Detection of Residual Stress - Mercury (I) Nitrate Test First Edition
ISO
197-1
Copper and Copper Alloys - Terms and Definitions - Part 1: Materials First Edition
ISO
197-2
Copper and Copper Alloys - Terms and Definitions - Part 2: Unwrought Products (Refinery Shapes) First Edition
ISO
197-3
Copper and Copper Alloys - Terms and Definitions - Part 3: Wrought Products First Edition
ISO
197-4
Copper and Copper Alloys - Terms and Definitions - Part 4: Castings First Edition
ISO
197-5
Copper and Copper Alloys - Terms and Definitions - Part 5: Methods of Processing and Treatment First Edition
ISO
199
Rolling Bearings - Thrust Bearings - Tolerances Third edition
ISO
204
Metallic Materials - Uninterrupted Uniaxial Creep Testing in Tension - Method of Test First Edition
ISO
209
Title not available [Cancelled: ISO 209-1, ISO 209-2]
ISO
212
Essential Oils - Sampling Second Edition
ISO
214
Documentation - Abstracts for Publications and Documentation First Edition
ISO
215
Documentation - Presentation of Contributions to Periodicals and Other Serials First Edition
Writing paper and certain classes of printed matter - Trimmed sizes - A and B series, and indication of machine direction Second
ISO
216
Edition
Paper - Untrimmed Sizes - Designation and Tolerances for Primary and Supplementary Ranges, and Indication of Machine Direction
ISO
217
Second Edition
Fasteners - Bolts, Screws, Studs and Nuts - Symbols and Designations of Dimensions Second Edition; Corrected and Reprinted
ISO
225
7/15/1992
ISO
226
Acoustics Normal equal-loudness-level contours Second edition; Supersedes NZS ISO 226: 1987
Pipe Threads Where Pressure-Tight Joints Are Not Made on the Threads - Part 1: Dimensions, Tolerances and Designation Fourth
ISO
228-1
Edition
Pipe Threads Where Pressure-Tight Joints Are Not Made on the Threads - Part 2: Verification by Means of Limit Gauges Second
ISO
228-2
Edition
ISO
229
Machine Tools - Speeds and Feeds First Edition
Test Code for Machine Tools - Part 1: Geometric Accuracy of Machines Operating under No-Load or Finishing Conditions Second
ISO
230-1
Edition
Test code for machine tools - Part 2: Determination of accuracy and repeatability of positioning numerically controlled axes Third
ISO
230-2
Edition
ISO
230-3
Test Code for Machine Tools - Part 3: Determination of Thermal Effects Second Edition
ISO
230-4
Test code for machine tools Part 4: Circular tests for numerically controlled machine tools Second Edition
ISO
230-5
Test Code for Machine Tools - Part 5: Determination of the Noise Emission First Edition
Test code for machine tools Part 6: Determination of positioning accuracy on body and face diagonals (Diagonal displacement tests)
ISO
230-6
First edition
ISO
230-7
Test code for machine tools Part 7: Geometric accuracy of axes of rotation First edition
ISO
233
Documentation - Transliteration of Arabic Characters into Latin Characters First Edition
Information and Documentation - Transliteration of Arabic Characters - into Latin Characters - Part 2: Arabic Language - Simplified
ISO
233-2
Transliteration First Edition
Information and Documentation - Transliteration of Arabic Characters into Latin Characters - Part 3: Persian Language - Simplified
ISO
233-3
Transliteration First Edition
ISO
234-1
Files and Rasps - Part 1: Dimensions
ISO
234-2
Files and Rasps - Part 2: Characteristics of Cut First Edition
Parallel Shank Jobber and Stub Series Drills and Morse Taper Shank Drills Second Edition; Amendment Slip-1981; Corrigendum 1-
ISO
235
1996
ISO
236-1
Hand Reamers First Edition; Amendment 1: 2/15/1977
ISO
236-2
Long Fluted Machine Reamers, Morse Taper Shanks First Edition; Amendment 1: 2/15/1977
ISO
237
Rotating Tools with Parallel Shanks - Diameters of Shanks and Sizes of Driving Squares First Edition
ISO
238
Reduction Sleeves and Extension Sockets for Tools with Morse Taper Shanks First Edition
ISO
239
Drill Chuck Tapers Second Edition
ISO
240
Milling Cutters - Interchangeability Dimensions for Cutter Arbors or Cutter Mandrels Second Edition
ISO
241
Shanks for Turning and Planing Tools - Shapes and Dimensions of the Section Second Edition
ISO
242
Carbide Tips for Brazing on Turning Tools First Edition
ISO
243
Turning Tools with Carbide Tips - External Tools
ISO
244
Aircraft - Sealing Wire First Edition
ISO
245
Aircraft - Lockwire - Diameters Second Edition
ISO
246
Rolling bearings ù Cylindrical roller bearings, separate thrust collars ù Boundary dimensions Third Edition
ISO
247
Rubber - Determination of Ash Fourth Edition
ISO
248
Rubbers, raw - Determination of volatile-matter content Fourth Edition
ISO
249
Rubber, Raw Natural - Determination of Dirt Content Third Edition
ISO
251
Conveyor belts with textile carcass Widths and lengths Third Edition
ISO
252
Conveyor belts ù Adhesion between constitutive elements ù Test methods Third Edition
Textile Conveyor Belts - Adhesive Strength between Constitutive Elements - Part 1: Methods of Test First Edition; Partially Replaces
ISO
252-1
ISO 252: 1988; Corrigendum 1: 11/15/2006
ISO
254
Belt Drives - Pulleys - Quality, Finish and Balance Third Edition
ISO
255
Belt Drives - Pulleys for V-Belts (System Based on Datum Width) - Geometrical Inspection of Grooves Second Edition
ISO
257
Pesticides and other agrochemicals Principles for the selection of common names Third Edition
ISO
259
Documentation - Transliteration of Hebrew Characters into Latin Characters First Edition; Cancels and Replaces ISO R 259-1962
Information and Documentation - Transliteration of Hebrew Characters into Latin Characters - Part 2: Simplified Transliteration First
ISO
259-2
Edition; Corrected and Reprinted - 1995
ISO
261
ISO General Purpose Metric Screw Threads - General Plan Second Edition
ISO
262
ISO General Purpose Metric Screw Threads - Selected Sizes for Screws, Bolts and Nuts Second Edition
ISO
263
ISO Inch Screw Threads - General Plan and Selection for Screws, Bolts and Nuts - Diameter Range 0,06 to 6 in First Edition
Unplasticized Polyvinyl Chloride (PVC) Fittings with Plain Sockets for Pipes under Pressure - Laying Length - Metric Series First
ISO
264
Edition; Addendum 1-1982
Pipes and Fittings of Plastics Materials - Fittings for Domestic and Industrial Waste Pipes - Basic Dimensions: Metric Series - Part 1:
ISO
265-1
Unplasticized Poly(Vinyl Chloride) (PVC-U) First Edition
ISO
266
Acoustics - Preferred Frequencies Second Edition
ISO
268
Aircraft - Mechanical and Electromechanical Indicators - General Requirements First Edition
ISO
269
Correspondence Envelopes - Designation and Sizes Second Edition; PNS 319: 1989
ISO
272
Fasteners - Hexagon Products - Widths Across Flats Second Edition
ISO
273
Fasteners - Clearance Holes for Bolts and Screws First Edition; Amendment Slip-1979; NZS/ISO 273: 1979
ISO
276
Binders for Paints and Varnishes - Linseed Stand Oil - Requirements and Methods of Test Second Edition
ISO
277
Binders for Paints and Varnishes - Raw Tung Oil - Requirements and Methods of Test Second Edition
ISO
279
Essential Oils - Determination of Relative Density at 20 Degrees C - Reference Method second Edition
ISO
280
Essential Oils - Determination of Refractive Index Second Edition
ISO
281
Rolling bearings ù Dynamic load ratings and rating life Second Edition
ISO
282
Conveyor Belts - Sampling Second Edition
Textile conveyor belts ù Full thickness tensile strength, elongation at break and elongation at the reference load ù Test method Third
ISO
283
Edition [Superseded: ISO 283-1, ISO 283-1]
ISO
284
Conveyor Belts - Electrical Conductivity - Specification and Test Method Third Edition
ISO System of Limits and Fits - Part 1: Bases of Tolerances, Deviations and Fits First Edition; CEN EN 20286-1: 1993; NZS/ISO
ISO
286-1
286.1: 1988
ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts First Edition;
ISO
286-2
Technical Corrigendum 1: 09/15/2006
ISO
287
Paper and Board - Determination of Moisture Content - Oven-Drying Method Second Edition; CEN EN 20287: 1994
Rubber, Unvulcanized - Determinations Using a Shearing-Disc Viscometer - Part 1: Determination of Mooney Viscosity Second
ISO
289-1
edition
Rubber, Unvulcanized - Determinations Using a Shearing-Disc Viscometer - Part 2: Determination of Pre-Vulcanization
ISO
289-2
Characteristics First Edition
Rubber, Unvulcanized - Determinations Using a Shearing-Disc Viscometer - Part 3: Determination of the Delta Mooney Value for Non-
ISO
289-3
Pigmented, Oil-Extended, Emulsion-Polymerized SBR First Edition
Rubber, unvulcanized Determinations using a shearing-disc viscometer Part 4: Determination of the Mooney stress-relaxation rate
ISO
289-4
First Edition; Corrected Version: 03/01/2004
ISO
291
Plastics Standard atmospheres for conditioning and testing Third Edition
ISO
293
Plastics Compression moulding of test specimens of thermoplastic materials Third Edition
Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose
ISO
294-1
and bar test specimens First Edition; Supersedes ISO 294: 1995; Amendment 1: 01-15-2001; Amendment 2: 09-01-2005
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 2: Small Tensile Bars First Edition; Supersedes ISO
ISO
294-2
294: 1995; Amendment 1: 05/15/2004
ISO
294-3 AMD 1
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 3: Small Plates AMENDMENT 1 Second Edition
ISO
294-3
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 3: Small Plates Second Edition
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 4: Determination of Moulding Shrinkage Second
ISO
294-4
Edition
Plastics - Injection Moulding of Test Specimens of Thermoplastic Materials - Part 5: Preparation of Standard Specimens for
ISO
294-5
Investigating Anisotropy First Edition; Technical Corrigendum 1: 3/15/2003; Amendment 1: 05/01/2004
ISO
295
Plastics - Compression Moulding of Test Specimens of Thermosetting Materials Third Edition
ISO
296
Machine Tools - Self-Holding Tapers for Tool Shanks Second Edition
ISO
297
7/24 Tapers for Tool Shanks for Manual Changing Second Edition
ISO
298
Machine Tools - Lathe Centres - Sizes for Interchangeability First Edition
ISO
299
Machine Tool Tables - T-Slots and Corresponding Bolts Second Edition
ISO
301
Zinc Alloy Ingots Intended for Casting Second Edition
ISO
302
Pulps Determination of Kappa number Second Edition
Road vehicles ù Installation of lighting and light signalling devices for motor vehicles and their trailers TECHNICAL CORRIGENDUM
ISO
303 CORR 1
1 Second Edition
ISO
303
Road vehicles ù Installation of lighting and light signalling devices for motor vehicles and their trailers Second Edition
Surface Active Agents - Determination of Surface Tension by Drawing up Liquid Films Second Edition; Technical Corrigendum 1-
ISO
304
1998
Plastics - Determination of Thermal Stability of Poly(Vinyl Chloride), Related Chlorine-Containing Homopolymers and Copolymers
ISO
305
and Their Compounds - Discoloration Method Second Edition
ISO
306
Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) Fourth Edition
ISO
307
Plastics ù Polyamides ù Determination of viscosity number Fifth Edition
Plastics - Phenolic Moulding Materials - Determination of Acetone-Soluble Matter (Apparent Resin Content of Material in the
ISO
308
Unmoulded State) Third Edition
Manganese Ores and Concentrates - Determination of Hygroscopic Moisture Content in Analytical Samples - Gravimetric Method
ISO
310
Third Edition
ISO
312
Manganese Ores - Determination of Active Oxygen Content, Expressed as Manganese Dioxide - Titrimetric Method Third Edition
ISO
314
Manganese Ores - Determination of Carbon Dioxide Content - Gravimetric Method Second Edition
Manganese Ores and Concentrates - Determination of Nickel Content - Dimethylglyoxime Spectrometric Method and Flame Atomic
ISO
315
Absorption Spectrometric Method First Edition
ISO
316
Manganese Ores - Determination of Cobalt Content - Nitroso-R-Salt Photometric Method Second Edition
ISO
317
Manganese Ores and Concentrates - Determination of Arsenic Content - Spectrometric Method First Edition
Manganese Ores - Determination of Sulphur Content - Barium Sulphate Gravimetric Methods and Sulphur Dioxide Titrimetric Method
ISO
320
After Combustion Second Edition
ISO
333
Coal - Determination of Nitrogen - Semi-Micro Kjeldahl Method Fourth Edition; Corrigendum 1-1996
ISO
334
Solid Mineral Fuels - Determination of Total Sulfur - Eschka Method Second Edition
Road Vehicles - 50 Semi-Trailer Fifth Wheel Coupling Pin - Basic and Mounting/Interchangeability Dimensions Second Edition;
ISO
337
Corrigendum 1-1990
ISO
340
Conveyor belts Laboratory scale flammability characteristics Requirements and test method Third Edition
ISO
342
Textile Machinery and Accessories - Worsted and Woollen Cards - Width of Cylinder and Width on the Wire Second Edition
ISO
344
Textile Machinery and Accessories - Spinning Machines - Flyer Bobbins First Edition
ISO
349
Hard Coal - Audibert-Arnu Dilatometer Test First Edition
ISO
351
Solid Mineral Fuels - Determination of Total Sulfur - High Temperature Combustion Method Third Edition; Corrigendum 1-1996
ISO
354
Acoustics Measurement of sound absorption in a reverberation room Second Edition
ISO
355
Rolling bearings ù Tapered roller bearings ù Boundary dimensions and series designations Second Edition
ISO
356
Essential Oils - Preparation of Test Samples Second Edition
ISO
359
Cinematography - Projectable Image Area on 16 mm Motion-Picture Prints - Dimensions and Location Second Edition
ISO
361
Basic Ionizing Radiation Symbol First Edition
Measurement of noise emitted by accelerating road vehicles ù Engineering method ù Part 1: M and N categories First Edition
ISO
362-1
[Cancelled: ISO 362, ISO 362, ISO 7188]
Textile machinery and accessories - Flat steel healds with closed end loops - Part 1: Dimensions of healds manufactured of rolled
ISO
363-1
steel wire First Edition;:1992
Textile machinery and accessories Flat steel healds with closed end loops Part 2: Dimensions of healds manufactured of hardened
ISO
363-2
strip steel First Edition
ISO
364
Textile Machinery and Accessories - Twin Wire Healds for Weaving Machines with Heald Frames First Edition
ISO
365
Textile Machinery and Accessories - Twin Wire Healds with Inset Mail for Jacquard Weaving Second Edition
ISO
366-1
Textile Machinery and Accessories - Reeds - Part 1: Pitch Bound Reeds - Dimensions First Edition
Textile Machinery and Accessories - Reeds - Part 2: Metal Reeds with Plate Baulk - Dimensions and Designation First Edition;
ISO
366-2
Replaces ISO 367: 1976
Textile Machinery and Accessories - Reeds - Part 3: Metal Reeds with Double-Spring Baulk - Dimensions and Designation First
ISO
366-3
Edition
ISO
366-4
Textile machinery and accessories - Reeds - Part 4: Dimensions and designation of plasticbound metal reeds Second edition
ISO
366-5
Textile machinery and accessories Reeds Part 5: Dimensions and designation of profile capsules First Edition
Spinning Preparatory, Spinning and Doubling (Twisting) Machinery - Tubes for Ring-Spinning, Doubling and Twisting Spindles, Taper
ISO
368
1:38 and 1:64 Fourth Edition
ISO
376
Metallic Materials - Calibration of Force-Proving Instruments Used for the Verification of Uniaxial Testing Machines Third Edition
Steel and Steel Products - Location and Preparation of Samples and Test Pieces for Mechanical Testing Second Edition;
ISO
377
Corrigendum 1 09-15-1997
ISO
378
Gymnastic Equipment - Parallel Bars First Edition
ISO
379
Gymnastic Equipment - Horizontal Bar First Edition
ISO
383
Laboratory Glassware - Interchangeable Conical Ground Joints First Edition
ISO
384
Laboratory Glassware - Principles of Design and Construction of Volumetric Glassware First Edition
ISO
385
Laboratory glassware Burettes First Edition; Replaces ISO 385-1:1984, ISO 385-2:1984, ISO 385-3:1984
ISO
386
Liquid-in-Glass Laboratory Thermometers - Principles of Design, Construction and Use First Edition;
ISO
387
Hydrometers - Principles of Construction and Adjustment First Edition;
Acoustics - Reference Zero for the Calibration of Audiometric Equipment - Part 1: Reference Equivalent Threshold Sound Pressure
ISO
389-1
Levels for Pure Tones and Supra-Aural Earphones First Edition
Acoustics - Reference Zero for the Calibration of Audiometric Equipment - Part 2: Reference Equivalent Threshold Sound Pressure
ISO
389-2
Levels for Pure Tones and Insert Earphones First Edition
Acoustics - Reference Zero for the Calibration of Audiometric Equipment - Part 3: Reference Equivalent Threshold Force Levels for
ISO
389-3
Pure Tones and Bone Vibrators First Edition; Corrigendum 1-1995; AS/NZS 1591.1: 1995
Acoustics - Reference Zero for the Calibration of Audiometric Equipment - Part 4: Reference Levels for Narrow-Band Masking Noise
ISO
389-4
First Edition
Acoustics Reference zero for the calibration of audiometric equipment Part 5: Reference equivalent threshold sound pressure levels
ISO
389-5
for pure tones in the frequency range 8 kHz to 16 kHz First Edition;:1998
Acoustics ù Reference zero for the calibration of audiometric equipment ù Part 6: Reference threshold of hearing for test signals of
ISO
389-6
short duration First Edition
Acoustics Reference zero for the calibration of audiometric equipment Part 7: Reference threshold of hearing under free-field and
ISO
389-7
diffuse-field listening conditions Second Edition
Acoustics Reference zero for the calibration of audiometric equipment Part 8: Reference equivalent threshold sound pressure levels
ISO
389-8
for pure tones and circumaural earphones First Edition
ISO
390
Products in Fibre-Reinforced Cement - Sampling and Inspection Second Edition
ISO
404
Steel and Steel Products - General Technical Delivery Requirements Second Edition
ISO
406
Technical Drawings - Tolerancing of Linear and Angular Dimensions Second Edition
ISO
407
Small Medical Gas Cylinders - Pin-Index Yoke-Type Valve Connections Third Edition
ISO
413
Aircraft - Heads of Lubricating Nipples First Edition
ISO
415
Envelopes, Postcards and Similar Articles - Cancellation Area First Edition
ISO
416
Picture Postcards - Area Reserved for the Address First Edition
ISO
418
Photography - Processing Chemicals - Specifications for Anhydrous Sodium Sulfite Third Edition
ISO
420
Photography - Processing Chemicals - Specifications for Potassium Bromide Second Edition
ISO
422
Photography - Processing Chemicals - Specifications for p-Menthylaminophenol Sulfate Second Edition
ISO
423
Photography - Processing Chemicals - Specifications for Hydroquinone Second Edition
ISO
424
Photography - Processing Chemicals - Specifications for Anhydrous Sodium Carbonate Monohydrate Second Edition
ISO
431
Copper Refinery Shapes Second Edition
ISO
432
Ply Type Conveyor Belts - Characteristics of Construction Second Edition
ISO
433
Conveyor Belts - Marking Second Edition, Amendment 1: 01/15/2006
ISO
437
Steel and Cast Iron - Determination of Total Carbon Content - Combustion Gravimetric Method First Edition
ISO
439
Steel and Cast Iron - Determination of Total Silicon Content - Gravimetric Method Second Edition
Textile Machinery and Accessories - Drop Wires for Warp Stop Motions for Weaving Machines without Automatic Drawing-In Second
ISO
441
Edition
ISO
445
Pallets for Materials Handling - Vocabulary Second Edition
ISO
446
Micrographics ISO character and ISO test chart No. 1 Description and use Third Edition
ISO
447
Machine Tools - Direction of Operation of Controls Second Edition
Ships and Marine Technology - Magnetic Compasses, Binnacles and Azimuth Reading Devices - Class A Second Edition; Corrected
ISO
449
and Reprinted 04/01/1999
ISO
451
Aircraft - Pressure Re-Oiling Connection First Edition; Erratum-1980
ISO
456
Surface Active Agents - Analysis of Soaps - Determination of Free Caustic Alkali First Edition
ISO
457
Soaps - Determination of Chloride Content - Titrimetric Method Second Edition
ISO
458-1
Plastics - Determination of Stiffness in Torsion of Flexible Materials - Part 1: General Method First Edition
Plastics - Determination of Stiffness in Torsion of Flexible Materials - Part 2: Application to Plasticized Compounds of Homopolymers
ISO
458-2
and Copolymers of Vinyl Chloride First Edition
ISO
461-1
Aircraft - Connectors for Ground Electrical Supplies - Part 1: Design, Performance and Test Requirements Second Edition
ISO
461-2
Aircraft - Connectors for Ground Electrical Supplies - Part 2: Dimensions First Edition
Geometrical Product Specifications (GPS) ù Dimensional measuring equipment ù Design and metrological characteristics of
ISO
463 CORR 1
mechanical dial gauges CORR 1 First Edition;:1965 [Replaced: ISO R463]
Geometrical Product Specifications (GPS) Dimensional measuring equipment Design and metrological characteristics of
ISO
463
mechanical dial gauges First Edition;:1965 [Replaced: ISO R463]
ISO
464
Rolling Bearings - Radial Bearings with Locating Snap Ring - Dimensions and Tolerances Second Edition
Cinematography - Image Produced by 16mm Motion-Picture Camera Aperture - Position and Dimensions First Edition; Amendment
ISO
466
Slip-1980
ISO
472
Plastics - Vocabulary Plastiques - Vocabulaire Third Edition
ISO
476
Textile Machinery and Accessories - Pirn Winding Machines - Vocabulary First Edition
ISO
477
Textile Machinery and Accessories - Cone and Cheese Winding Machines - Vocabulary First Edition
ISO
482
Aircraft - Propulsion Units and Components - Methods of Numbering and Describing Direction of Rotation First Edition
Plastics - Small Enclosures for Conditioning and Testing Using Aqueous Solutions to Maintain Relative Humidity at a Constant Value
ISO
483
Second Edition
ISO
484-1
Shipbuilding - Ship Screw Propellers - Manufacturing Tolerances - Part 1: Propellers of Diameter Greater Than 2,50 m First Edition
Shipbuilding - Ship Screw Propellers - Manufacturing Tolerances - Part 2: Propellers of Diameter between 0,80 and 2,50 m Inclusive
ISO
484-2
First Edition
ISO
485
Aircraft Water-Methanol Pressure Connections First Edition; Erratum-1980
ISO
486
Cinematography - 16 mm Motion-Picture Film Perforated 8 mm Type R - Cutting and Perforating Dimensions Third Edition
ISO
487
Steel Roller Chains, Types S and C, Attachments and Sprockets Third Edition
ISO
488
Milk - Determination of Fat Content - Gerber Butyrometers First Edition
ISO
489
Plastics - Determination of the Refractive Index Second Edition
Cinematography - Magnetic Stripes and Magnetic Recording Head Gaps for Sound Record on 16 mm Motion-Picture Film Perforated
ISO
490
Along One Edge (Type 1) - Positions and Width Dimensions Second Edition
ISO
491
Cinematography - 35 mm Motion-Picture Film and Magnetic Film - Cutting and Perforating Dimensions Sixth Edition
ISO
492
Rolling Bearings - Radial Bearings - Tolerances Fourth Edition
ISO
493
Aircraft - Dimensions for Single-Hole Mounting (Class 1 and Class 2) Lever-Operated Manual Switches First Edition
ISO
494
Parallel Shank Twist Drills - Long Series First Edition
ISO
496
Driving and Driven Machines - Shaft Heights First Edition
Guide to the Choice of Series of Preferred Numbers and of Series Containing More Rounded Values of Preferred Numbers First
ISO
497
Edition
ISO
498
Natural Rubber Latex Concentrate - Preparation of Dry Films Second Edition
Agricultural tractors ù Rear-mounted power take-off types 1, 2 and 3 ù Part 1: General specifications, safety requirements,
ISO
500-1 CORR 1
dimensions for master shield and clearance zone TECHNICAL CORRIGENDUM 1 First Edition
Agricultural tractors ù Rear-mounted power take-off types 1, 2 and 3 ù Part 1: General specifications, safety requirements,
ISO
500-1
dimensions for master shield and clearance zone First Edition
Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 2: Narrow-track tractors, dimensions for master shield and
ISO
500-2
clearance zone First Edition; Together With ISO 500-1:2004 and ISO 500-3:2004 Replaces ISO 500:1991
Agricultural tractors Rear-mounted power take-off types 1, 2 and 3 Part 3: Main PTO dimensions and spline dimensions, location of
ISO
500-3
PTO First Edition; Together With ISO 500-1:2004 and ISO 500-2:2004 Replaces ISO 500:1991
ISO
501
Hard Coal - Determination of the Crucible Swelling Number Third Edition
ISO
502
Coal - Determination of Caking Power - Gray-King Coke Test Second Edition
ISO
504
Turning Tools with Carbide Tips - Designation and Marking First Edition
ISO
505
Conveyor Belts - Method for the Determination of the Tear Propagation Resistance of Textile Conveyor Belts Second Edition
ISO
506
Rubber Latex, Natural, Concentrate - Determination of Volatile Fatty Acid Number Third Edition
ISO
509
Pallet Trucks - Principal Dimensions First Edition; Replaces ISO R509: 1966
ISO
510
Red Lead for Paints First Edition
Classification and application of hard cutting materials for metal removal with defined cutting edges Designation of the main groups
ISO
513
and groups of application Third Edition;
ISO
514
Turning Tools with Carbide Tips - Internal Tools First Edition
ISO
516
Photography - Camera Shutters - Timing Third Edition
Photography Apertures and related properties pertaining to photographic lenses Designations and measurements Second Edition;
ISO
517
Technical Corrigendum: 10/01/2006
Photography Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units
ISO
518
Specification Second Edition
ISO
519
Photography - Hand-Held Cameras - Flash-Connector Dimensions Second Edition
ISO
520
Cereals and Pulses - Determination of the Mass of 1000 Grains First Edition
ISO
521
Machine Chucking Reamers with Parallel Shanks or Morse Taper Shanks First Edition
ISO
522
Special Tolerances for Reamers First Edition
ISO
525
Bonded Abrasive Products - General Requirements Third Edition
Plastics - Determination of tensile properties - Part 1: General principles First Edition; Corrigendum 1-1994; Amendment 1: 09-01-
ISO
527-1
2005
ISO
527-2
Plastics - Determination of Tensile Properties - Part 2: Test Conditions for Moulding and Extrusion Plastics First Edition
Plastics - Determination of Tensile Properties - Part 3: Test Conditions for Films and Sheets First Edition; Technical Corrigendum
ISO
527-3
1:06-15-1998; Technical Corrigendum 2:04-15-2001
PLastics - Determination of Tensile Properties - Part 4: Test Conditions for Isotropic and Orthotropic Fibre-Reinforced Plastic
ISO
527-4
Composites First Edition; Replaces ISO 3268:1978
Plastics - Determination of Tensile Properties - Part 5: Test Conditions for Unidirectional Fibre-Reinforced Plastic Composites First
ISO
527-5
Edition; Replaces 3268:1978
ISO
528
Refractory Products - Determination of Pyrometric Cone Equivalent (Refractoriness) First Edition
ISO
529
Short Machine Taps and Hand Taps Second Edition
ISO
530
Aircraft - General Purpose Push-Pull Single-Pole Circuit-Breakers - Dimensions First Edition
ISO
532
Acoustics - Method for Calculating Loudness Level First Edition
ISO
534
Paper and Board - Determination of Thickness and Apparent Bulk Density or Apparent Sheet Density Third Edition
ISO
535
Paper and Board - Determination of Water Absorptiveness - Cobb Method Second Edition; CEN EN 20535: 1994
ISO
536
Paper and Board - Determination of Grammage Second Edition
ISO
540
Solid Mineral Fuels - Determination of Fusibility of Ash - High-Temperature Tube Method Third Edition
ISO
542
Oilseeds - Sampling Second Edition; CEN EN ISO 542: 1995
Welding consumables Technical delivery conditions for welding filler materials Type of product, dimensions, tolerances and
ISO
544
markings Third Edition
ISO
548
Manganese Ores - Determination of Barium Oxide Content - Barium Sulphate Gravimetric Method Second Edition
ISO
549
Manganese Ores - Determination of Combined Water Content - Gravimetric Method Second Edition
Manganese Ores - Determination of Vanadium Content - Titrimetric Method and Phosphotungstovanadate Photometric Method
ISO
553
Second Edition
ISO
554
Standard Atmospheres for Conditioning and/or Testing - Specifications First Edition
ISO
556
Coke (Greater Than 20 mm in Size) - Determination of Mechanical Strength First Edition
ISO
558
Conditioning and Testing - Standard Atmospheres - Definitions First Edition
ISO
559
Steel Tubes for Water and Sewage Second Edition
ISO
561
Coal Preparation Plant - Graphical Symbols Second Edition; Corrected and Reprinted - 1992
ISO
562
Hard Coal and Coke - Determination of Volatile Matter Third Edition
ISO
565
Test Sieves - Metal Wire Cloth, Perforated Metal Plate and Electroformed Sheet - Nominal Sizes of Openings Third Edition
ISO
567
Coke - Determination of Bulk Density in a Small Container Second Edition
ISO
570
Textile Machinery and Accessories - Heald Carrying Rods for Healds with ClosedO"-Shaped End Loops First Edition"
ISO
572
Textile Machinery and Accessories - Shuttles for Pirn Changing Automatic Looms - Dimensions First Edition; Erratum-1976
ISO
575
Textile Machinery and Accessories - Transfer Cones - Half Angle of the Cone 4 Degrees 20 Feet First Edition
ISO
576
Textile Machinery and Accessories - Paper Patterns for Dobbies - Dimensions First Edition
ISO
579
Coke - Determination of Total Moisture Third Edition
Plastics piping and ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating
ISO
580
Third Edition
ISO
582
Rolling Bearings - Chamfer Dimensions - Maximum Values Third Edition
Conveyor belts with a textile carcass ù Total belt thickness and thickness of constitutive elements ù Test methods Third Edition
ISO
583
[Cancelled: ISO 583-1, ISO 583-1]
Conveyor belts with a textile carcass Total thickness and thickness of elements Part 1: Methods of test First Edition; Technical
ISO
583-1
Corrigendum 1: 12/01/2006; Together with 583-2 Replaces ISO 583:1990 [Cancelled By: ISO 583, ISO 583]
ISO
584
Plastics - Unsaturated Polyester Resins - Determination of Reactivity at 80 Degrees C (Conventional Method) First Edition
ISO
585
Plastics - Unplasticized Cellulose Acetate - Determination of Moisture Content Second Edition
ISO
587
Solid Mineral Fuels - Determination of Chlorine Using Eschka Mixture Third Edition
ISO
589
Hard coal Determination of total moisture Third Edition
ISO
590
Oil of Brazilian Sassafras First Edition
ISO
591-1
Titanium Dioxide Pigments for Paints - Part 1: Specifications and Methods of Tests First Edition; Replaces ISO 591
ISO
592
Essential Oils - Determination of Optical Rotation Second Edition
Conical Fittings with a 6 % (Luer) Taper for Syringes, Needles and Certain Other Medical Equipment - Part 1: General Requirements
ISO
594-1
First Edition; CEN EN 20594-1: 1993
Conical Fittings with a 6 % (Luer) Taper for Syringes, Needles and Certain Other Medical Equipment - Part 2: Lock Fittings Second
ISO
594-2
Edition
ISO
595-1
Reusable All-Glass or Metal-and-Glass Syringes for Medical Use - Part 1: Dimensions First Edition; Corrected and Reprinted - 1988
Reusable All-Glass or Metal-and-Glass Syringes for Medical Use - Part 2: Design, Performance Requirements and Tests First
ISO
595-2
Edition; CEN EN ISO 595-2: 1994
Solid Mineral Fuels - Determination of Arsenic Content Using the Standard Silver Diethyldithiocarbamate Photometric Method of ISO
ISO
601
2590 First Edition
ISO
602
Coal - Determination of Mineral Matter Second Edition
Bonded Abrasive Products - Dimensions - Part 1: Grinding Wheels for External Cylindrical Grinding between Centres First Edition;
Technical Corrigendum 1: 11-15-1999; Together with ISO 603-2: 1999 to ISO 603-16: 1999, Cancels and Replaces ISO/R 603: 1967,
ISO
603-1
ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 2: Grinding Wheels for Centreless External Cylindrical Grinding Second Edition;
Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 and ISO 603-3: 1999 to ISO 603-16: 1999, Cancels and
Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976
ISO
603-2
and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 3: Grinding Wheels for Internal Cylindrical Grinding First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999, ISO 603-2: 1999 and ISO 603-4: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-3
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 4: Grinding Wheels for Surface Grinding/Peripheral Grinding First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-3: 1999 and ISO 603-5: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-4
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 5: Grinding Wheels for Surface Grinding/Face Grinding First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-4: 1999 and ISO 603-6: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-5
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 6: Grinding Wheels for Tool and Tool Room Grinding First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-5: 1999 and ISO 603-7: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-6
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 7: Grinding Wheels for Manually Guided Grinding First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-6: 1999 and ISO 603-8: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-7
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 8: Grinding Wheels for Deburring and Fettling/Snagging First Edition; Technical
Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-7: 1999 and ISO 603-9: 1999 to ISO 603-16: 1999, Cancels
and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920:
ISO
603-8
1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 9: Grinding Wheels for High-Pressure Grinding First Edition; Technical Corrigendum
1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-8: 1999 and ISO 603-10: 1999 to ISO 603-16: 1999, Cancels and
Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976
ISO
603-9
and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 10: Stones for Honing and Superfinishings First Edition; Technical Corrigendum 1: 11-
15-1999; Together with ISO 603-1: 1999 to ISO 603-9: 1999 and ISO 603-11: 1999 to ISO 603-16: 1999, Cancels and Replaces
ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976 and ISO
ISO
603-10
3921: 1976
Bonded Abrasive Products - Dimensions - Part 11: Hand Finishing Sticks First Edition; Technical Corrigendum 1: 11-15-1999;
Together with ISO 603-1: 1999 to ISO 603-10: 1999 and ISO 603-12: 1999 to ISO 603-16: 1999, Cancels and Replaces ISO/R 603:
ISO
603-11
1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 12: Grinding Wheels for Deburring and Fettling on a Straight Grinder First Edition;
Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-11: 1999 and ISO 603-13: 1999 to ISO 603-16:
1999, Cancels and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976,
ISO
603-12
ISO 3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 13: Grinding Wheels for Deburring and Fettling on a Vertical Grinder First Edition;
Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-12: 1999 and ISO 603-14: 1999 to ISO 603-16:
1999, Cancels and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976,
ISO
603-13
ISO 3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 14: Grinding Wheels for Deburring and Fettling/Snagging on an Angle Grinder First
Edition; Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-13: 1999, ISO 603-15: 1999 and ISO 603-
16: 1999, Cancels and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290:
ISO
603-14
1976, ISO 3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 15: Grinding Wheels for Cutting-Off on Stationary or Mobile Cutting-Off Machines
First Edition; Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-14: 1999 and ISO 603-16: 1999,
Cancels and Replaces ISO/R 603: 1967, ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO
ISO
603-15
3920: 1976 and ISO 3921: 1976
Bonded Abrasive Products - Dimensions - Part 16: Grinding Wheels for Cutting-Off on Hand Held Power Tools First Edition;
Technical Corrigendum 1: 11-15-1999; Together with ISO 603-1: 1999 to ISO 603-15: 1999, Cancels and Replaces ISO/R 603: 1967,
ISO
603-16
ISO 603-2: 1981, ISO 1117: 1975, ISO 2220: 1972, ISO 2933: 1974, ISO 3290: 1976, ISO 3920: 1976 and ISO 3921: 1976
ISO
604
Plastics - Determination of Compressive Properties Third Edition
ISO
605
Pulses - Determination of Impurities, Size, Foreign Odours, Insects, and Species and Variety - Test Methods Second Edition
Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets TECHNICAL
ISO
606 CORR 1
CORRIGENDUM 1 Third Edition
ISO
606
Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets Third Edition
ISO
607
Surface Active Agents and Detergents - Methods of Sample Division First Edition
Solid Mineral Fuels - Determination of Carbon and Hydrogen - High Temperature Combustion Method Second Edition; Corrigendum
ISO
609
1-1996
ISO
610
High-Tensile Steel Chains (Round Link) for Chain Conveyors and Coal Ploughs Second Edition
Road Vehicles - Braking of Automotive Vehicles and Their Trailers - Vocabulary Vehicules Routiers - Freinage des Vehicules
ISO
611
Automobiles et de Leurs Remorques - Vocabulaire Fourth Edition
Road Vehicles - Dimensions of Motor Vehicles and Towed Vehicles - Terms and Definitions First Edition; Erratum-1979; PNS 634:
ISO
612
1992
ISO
613
Ships and Marine Technology - Magnetic Compasses, Binnacles and Azimuth Reading Devices - Class B Second Edition
Shipbuilding and Marine Structures - Toughened Safety Glass Panes for Rectangular Windows and Side Scuttles - Punch Method of
ISO
614
Non-Destructive Strength Testing Third Edition
ISO
616
Coke - Determination of Shatter Indices Second Edition
Manganese Ores - Determination of Chromium Content - Diphenylcarbazide Photometric Method and Silver Persulphate Titrimetric
ISO
619
Method Second Edition
Manganese Ores - Determination of Metallic Iron Content (Metallic Iron Content Not Exceeding 2 %) - Sulphosalicylic Acid
ISO
621
Photometric Method Second Edition
ISO
622
Solid Mineral Fuels - Determination of Phosphorus Content - Reduced Molybdophosphate Photometric Method First Edition
ISO
625
Solid Mineral Fuels - Determination of Carbon and Hydrogen - Liebig Method Second Edition; Corrigendum 1-1996
ISO
629
Steel and Cast Iron - Determination of Manganese Content - Spectrophotometric Method First Edition; PNS 557: 1993
ISO
630
Structural Steels - Plates, Wide Flats, Bars, Sections and Profiles Second Edition; AMENDMENT 1: 12/01/2003
ISO
630-2
Structural Steels - Part 2: Technical Delivery Requirements for Hot-Finished Hollow Sections First Edition
ISO
631
Mosaic Parquet Panels - General Characteristics First Edition
ISO
633
Cork - Vocabulary Li×ge ù Vocabulaire Second Edition
Welding consumables Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels Classification Third
ISO
636
Edition
ISO
638
Pulps - Determination of Dry Matter Content First Edition; CEN EN 20638: 1993
Codes for the Representation of Names of Languages - Part 1: Alpha-2 Code Codes pour la Representation des Noms de Langue -
ISO
639-1
Partie 1: Code Alpha-2 First Edition; Replaces ISO 639
Codes for the Representation of Names of Languages - Part 2: Alpha-3 Code Codes Pour La Representation Des Noms De Langue -
ISO
639-2
Partie 2: Code Alpha-3 First Edition
ISO
639-3
Codes for the representation of names of languages ù Part 3: Alpha-3 code for comprehensive coverage of languages First Edition
ISO
641
Laboratory Glassware - Interchangeable Spherical Ground Joints First Edition
ISO
642
Steel - Hardenability Test by End Quenching (Jominy Test) Second Edition
ISO
643
Steels - Micrographic Determination of the Apparent Grain Size Second Edition
ISO
646
Information Technology - ISO 7-Bit Coded Character Set for Information Interchange Third Edition
Brown Coals and Lignites - Determination of the Yields of Tar, Water, Gas and Coke Residue by Low Temperature Distillation First
ISO
647
Edition
ISO
648
Laboratory Glassware - One-Mark Pipettes First Edition
ISO
649-1
Laboratory Glassware - Density Hydrometers for General Purposes - Part 1: Specification First Edition
ISO
649-2
Laboratory Glassware - Density Hydrometers for General Purposes - Part 2: Test Methods and Use First Edition
ISO
650
Relative Density 60/60 Degrees F Hydrometers for General Purposes First Edition
ISO
651
Solid-Stem Calorimeter Thermometers First Edition
ISO
652
Enclosed-Scale Calorimeter Thermometers First Edition
ISO
653
Long Solid-Stem Thermometers for Precision Use First Edition
ISO
654
Short Solid-Stem Thermometers for Precision Use First Edition; Erratum-1982
ISO
655
Long Enclosed-Scale Thermometers for Precision Use First Edition; Erratum-1982
ISO
656
Short Enclosed-Scale Thermometers for Precision Use First Edition
ISO
657-1
Hot-Rolled Steel Sections - Part 1: Equal-Leg Angles - Dimensions First Edition
ISO
657-2
Hot-Rolled Steel Sections - Part 2: Unequal-Leg Angles - Dimensions First Edition
ISO
657-5
Hot-Rolled Steel Sections - Part V: Equal-Leg Angles and Unequal-Leg Angles - Tolerances for Metric and Inch Series First Edition
Hot-Rolled Steel Sections - Part 11: Sloping Flange Channel Sections (Metric Series) - Dimensions and Sectional Properties First
ISO
657-11
Edition
ISO
657-14
Hot-Rolled Steel Sections - Part 14: Hot-Finished Structural Hollow Sections - Dimensions and Sectional Properties Third Edition
Hot-Rolled Steel Sections - Part 15: Sloping Flange Beam Sections (Metric Series) - Dimensions and Sectional Properties First
ISO
657-15
Edition
Hot-Rolled Steel Sections - Part 16: Sloping Flange Column Sections (Metric Series) - Dimensions and Sectional Properties First
ISO
657-16
Edition
Hot-Rolled Steel Sections - Part 18: L Sections for Shipbuilding (Metric Series) - Dimensions, Sectional Properties and Tolerances
ISO
657-18
First Edition
ISO
657-19
Hot-Rolled Steel Sections - Part 19: Bulb Flats (Metric Series) - Dimensions, Sectional Properties and Tolerances First Edition
ISO
657-21
Hot-Rolled Steel Sections - Part 21: T-Sections with Equal Depth and Flange Width - Dimensions First Edition
ISO
658
Oilseeds - Determination of Content Impurities Third Edition
ISO
659
Oilseeds - Determination of Oil Content (Reference Method) Third Edition
ISO
660
Animal and Vegetable Fats and Oils - Determination of Acid Value and Acidity Second Edition; Amendment 1: 3/15/2003
ISO
661
Animal and vegetable fats and oils Preparation of test sample Third Edition
ISO
662
Animal and Vegetable Fats and Oils - Determination of Moisture and Volatile Matter Content Second Edition
ISO
663
Animal and vegetable fats and oils ù Determination of insoluble impurities content Fourth Edition
ISO
664
Oilseeds - Reduction of Laboratory Sample to Test Sample Second Edition
ISO
665
Oilseeds - Determination of Moisture and Volatile Matter Content Second Edition; Corrected Version: 04/01/2002
ISO
666
Machine tools Mounting of grinding wheels by means of hub flanges Third Edition
Series 1 freight containers - Classification, dimensions and ratings Fifth Edition; Amendment 1: 09/15/2005; Amendment 2:
ISO
668
10/01/2005
Resistance Welding - Resistance Welding Equipment - Mechanical and Electrical Requirements Second Edition * Corrected and
ISO
669
Reprinted 03/15/2001
ISO
671
Steel and Cast Iron - Determination of Sulphur Content - Combustion Titrimetric Method First Edition
ISO
672
Soaps - Determination of Moisture and Volatile Matter Content - Oven Method First Edition
ISO
673
Soaps - Determination of Content of Ethanol-Insoluble Matter Second Edition
Textiles - Woven Fabrics - Determination of Dimensional Change on Commercial Laundering Near the Boiling Point First Edition;
ISO
675
Corrigendum 1-1990
ISO
676
Spices and Condiments - Botanical Nomenclature Second Edition; Corrigendum 1-02/15/1997
ISO
677
Straight Bevel Gears for General Engineering and Heavy Engineering - Basic Rack First Edition
ISO
678
Straight Bevel Gears for General Engineering and Heavy Engineering - Modules and Diametral Pitches First Edition
ISO
679
Methods of Testing Cements - Determination of Strength First Edition
ISO
680
Cement - Test Methods - Chemical Analysis First Edition
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 1: Direct-Hardening Unalloyed and Low-Alloyed Wrought Steel in
ISO
683-1
Form of Different Black Products First Edition
ISO
683-9
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 9: Wrought Free-Cutting Steels First Edition
ISO
683-10
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 10: Wrought Nitriding Steels Second Edition
ISO
683-11
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 11: Wrought Case-Hardening Steels First Edition
ISO
683-14
Heat-treatable steels, alloy steels and free-cutting steels Part 14: Hot-rolled steels for quenched and tempered springs Third Edition
ISO
683-15
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 15: Valve Steels for Internal Combustion Engines Second Edition
ISO
683-17
Heat-Treated Steels, Alloy Steels and Free-Cutting Steels - Part 17: Ball and Roller Bearing Steels Second Edition
Heat-Treatable Steels, Alloy Steels and Free-Cutting Steels - Part 18: Bright Products of Unalloyed and Low Alloy Steels Second
ISO
683-18
Edition
ISO
684
Analysis of Soaps - Determination of Total Free Alkali First Edition
ISO
685
Analysis of Soaps - Determination of Total Alkali Content and Total Fatty Matter Content First Edition
ISO
687
Solid mineral fuels Coke Determination of moisture in the general analysis test sample Second Edition
ISO
690
Documentation - Bibliographic References - Content, Form and Structure Second Edition
ISO
690-2
Information and Documentation - Bibliographic References - Part 2: Electronic Documents or Parts Thereof First Edition
ISO
691
Assembly Tools for Screws and Nuts - Wrench and Socket Openings - Tolerances for General Use Fourth Edition
ISO
692
Pulps - Determination of Alkali Solubility Second Edition
ISO
693
Dimensions of Seam Welding Wheel Blanks First Edition
ISO
694
Ships and Marine Technology - Positioning of Magnetic Compasses in Ships First Edition
Glass - Resistance to Attack by a Boiling Aqueous Solution of Mixed Alkali - Method of Test and Classification Third Edition; PNS
ISO
695
1197: 1993
ISO
696
Surface Active Agents - Measurement of Foaming Power - Modified Ross-Miles Method First Edition
Surface Active Agents - Washing Powders - Determination of Apparent Density - Method by Measuring the Mass of a Given Volume
ISO
697
Second Edition
ISO
699
Pulps - Determination of Alkali Resistance Second Edition
ISO
701
International Gear Notation - Symbols for Geometrical Data Second Edition
ISO
702-1
Machine Tools - Connecting Dimensions of Spindle Noses and Work Holding Chucks - Part 1: Conical Connection Second Edition
ISO
702-2
Machine Tools - Spindle Noses and Face Plates - Sizes for Interchangeability - Part II: Camlock Type First Edition
ISO
702-3
Machine Tools - Spindle Noses and Face Plates - Sizes for Interchangeability - Part III: Bayonet Type First Edition
ISO
702-4
Machine tools Connecting dimensions of spindle noses and work holding chucks Part 4: Cylindrical connection First Edition
ISO
703
Conveyor belts ù Transverse flexibility (troughability) ù Test method Third Edition [Superseded: ISO 703-1, ISO 703-1]
ISO
704
Terminology Work - Principles and Methods Second Edition
ISO
705
Rubber Latex - Determination of Density between 5 Degrees C and 40 Degrees C Second Edition
ISO
706
Rubber Latex - Determination of Coagulum Content (Sieve Residue) Fourth Edition
ISO
707
Milk and Milk Products - Guidance on Sampling Second Edition
ISO
709
Essential Oils - Determination of Ester Value Second Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part I: General Rules of Representation First
ISO
710-I
Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part II: Representation of Sedimentary Rocks
ISO
710-II
First Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part III: Representation of Magmatic Rocks
ISO
710-III
First Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part 4: Representation of Metamorphic Rocks
ISO
710-4
First Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part 5: Representation of Minerals Second
ISO
710-5
Edition
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part 6: Representation of Contact Rocks and
Rocks Which Have Undergone Metasomatic, Pneumatolytic or Hydrothermal Transformation or Transformation by Weathering First
ISO
710-6
Edition
ISO
710-7
Graphical Symbols for Use on Detailed Maps, Plans and Geological Cross-Sections - Part 7: Tectonic Symbols First Edition
ISO
711
Cereals and Cereal Products - Determination of Moisture Content (Basic Reference Method) Second Edition
ISO
712
Cereals and Cereal Products - Determination of Moisture Content Routine Reference Method Third Edition
ISO
713
Zinc - Determination of Lead and Cadmium Contents - Polarographic Method First Edition
ISO
714
Zinc - Determination of Iron Content - Photometric Method First Edition
ISO
715
Zinc - Determination of Lead Content - Polarographic Method First Edition
Acoustics Rating of sound insulation in buildings and of building elements Part 1: Airborne sound insulation Second Edition;
ISO
717-1
Amendment 1: 08/15/2006
Acoustics Rating of sound insulation in buildings and of building elements Part 2: Impact sound insulation Second Edition;
ISO
717-2
Amendment 1: 08/15/2006
ISO
718
Laboratory Glassware - Thermal Shock and Thermal Shock Endurance - Test Methods Second Edition
ISO
719
Glass - Hydrolytic Resistance of Glass Grains at 98 Degrees C - Method of Test and Classification Second Edition
ISO
720
Glass - Hydrolytic Resistance of Glass Grains at 121 Degrees C - Method of Test and Classification Second Edition
ISO
721
Rock Drilling Equipment - Integral Stems Second Edition
ISO
722
Rock Drilling Equipment - Hollow Drill Steels in Bar Form, Hexagonal and Round Third Edition
Rock Drilling Equipment - Forged Collared Shanks and Corresponding Chuck Bushings for Hollow Hexagonal Drill Steels Second
ISO
723
Edition
ISO
724
ISO General-Purpose Metric Screw Threads - Basic Dimensions Second Edition
Fittings Made From Unplasticized Poly(Vinyl Chloride) (PVC-U), Chlorinated Poly(Vinyl Chloride) (PVC-C) or
ISO
727-1
Acrylonitrile/Butadiene/Styrene (ABS) With Plain Sockets for Pipes Under Pressure - Part 1: Metric Series First Edition
Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or
ISO
727-2
acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure Part 2: Inch-based series Second edition
ISO
728
Coke (Nominal Top Size Greater Than 20 mm) - Size Analysis by Sieving Third Edition
ISO
729
Oilseeds - Determination of Acidity of Oils Second Edition
Agricultural Wheeled Tractors - Rear-Mounted Three-Point Linkage - Part 1: Categories 1, 2, 3 and 4 Third Edition; Corrigendum 1-
ISO
730-1
1995
ISO
730-2
Agricultural Wheeled Tractors - Three-Point Linkage - Part II: Category 1 N (Narrow Hitch) First Edition
ISO
732
Photography - 120-Size and 220-Size Films - Dimensions Fourth Edition
ISO
734-1
Oilseed meals Determination of oil content Part 1: Extraction method with hexane (or light petroleum) Second Edition
Oilseed Residues - Determination of Oil Content - Part 2: Rapid Extraction Method First Edition; Together with ISO 734-1: 1998, it
ISO
734-2
Cancels and Replaces ISO 734: 1979
ISO
735
Oilseed Residues - Determination of Ash Insoluble in Hydrochloric Acid First Edition
ISO
737
Coniferous Sawn Timber - Sizes - Methods of Measurement First Edition
ISO
738
Coniferous Sawn Timber - Sizes - Permissible Deviations and Shrinkage First Edition
ISO
739
Sodium Carbonate for Industrial Use - Preparation and Storage of Test Samples First Edition
ISO
740
Sodium Carbonate for Industrial Use - Determination of Total Soluble Alkalinity - Titrimetric Method First Edition
ISO
746
Sodium Carbonate for Industrial Use - Determination of Matter Insoluble in Water at 50 Degrees Celsius First Edition
ISO
748
Measurement of Liquid Flow in Open Channels - Velocity-Area Methods Third Edition
ISO
749
Oilseed Residues - Determination of Total Ash First Edition
ISO
750
Fruit and Vegetable Products - Determination of Titratable Acidity Second Edition
ISO
751
Fruit and Vegetable Products - Determination of Water-Insoluble Solids Second Edition
ISO
752 CORR 1
Zinc ingots TECHNICAL CORRIGENDUM 1 Second Edition
ISO
752
Zinc ingots Second Edition
ISO
756-1
Propan-2-ol for Industrial Use - Methods of Test - Part 1: General First Edition
ISO
758
Liquid Chemical Products for Industrial Use - Determination of Density at 20 Degrees Celsius First Edition
Volatile Organic Liquids for Industrial Use - Determination of Dry Residue After Evaporation on a Water Bath - General Method First
ISO
759
Edition
ISO
760
Determination of Water - Karl Fischer Method (General Method) First Edition
ISO
762
Fruit and vegetable products Determination of mineral impurities content Second Edition
ISO
763
Fruit and vegetable products Determination of ash insoluble in hydrochloric acid Second Edition
ISO
764
Horology - Magnetic Resistant Watches Third Edition
ISO
765
Pesticides Considered Not to Require Common Names First Edition
Fibre Building Boards - Hard and Medium Boards - Determination of Water Absorption and of Swelling in Thickness After Immersion
ISO
769
in Water First Edition
ISO
770
Crude or Rectified Oils of Eucalyptus Globulus (Eucalyptus Globulus Labil.) Second Edition
ISO
771
Oilseed Residues - Determination of Moisture and Volatile Matter Content First Edition
ISO
772
Hydrometric Determinations - Vocabulary and Symbols Fourth Edition; Amendment 1:11/15/2002; Amendment 2: 05/01/2004
ISO
776
Pulps - Determination of Acid-Insoluble Ash Second Edition
ISO
777
Paper, board and pulp - Determination of acid-soluble calcium Third Edition
ISO
778
Paper, board and pulp - Determination of acid-soluble copper Third Edition
ISO
779
Paper, Board and Pulp - Determination of Iron Second Edition
ISO
780
Packaging - Pictorial Marking for Handling of Goods Fourth Edition
ISO
783
Metallic Materials - Tensile Testing at Elevated Temperature Second Edition
ISO
787-1
General Methods of Test for Pigments and Extenders - Part 1: Comparison of Colour of Pigments First Edition
General Methods of Test for Pigments and Extenders - Part 2: Determination of Matter Volatile at 105 Degrees Celsius First Edition;
ISO
787-2
CEN EN ISO 787-2: 1995
General Methods of Test for Pigments and Extenders - Part 3: Determination of Matter Soluble in Water - Hot Extraction Method
ISO
787-3
Second Edition
General Methods of Test for Pigments and Extenders - Part 4: Determination of Acidity or Alkalinity of the Aqueous Extract First
ISO
787-4
Edition
General Methods of Test for Pigments and Extenders - Part 5: Determination of Oil Absorption Value First Edition; CEN EN ISO 787-
ISO
787-5
5: 1995
General Methods of Test for Pigments and Extenders - Part 7: Determination of Residue on Sieve - Water Method - Manual
ISO
787-7
Procedure First Edition
General Methods of Test for Pigments and Extenders - Part 8: Determination of Matter Soluble in Water - Cold Extraction Method
ISO
787-8
Second Edition
General Methods of Test for Pigments and Extenders - Part 9: Determination of pH Value of an Aqueous Suspension First Edition;
ISO
787-9
CEN EN ISO 787-9: 1995
General Methods of Test for Pigments and Extenders - Part 10: Determination of Density - Pyknometer Method Second Edition; CEN
ISO
787-10
EN ISO 787-10: 1995
General Methods of Test for Pigments and Extenders - Part 11: Determination of Tamped Volume and Apparent Density After
ISO
787-11
Tamping First Edition; CEN EN ISO 787-11: 1995
ISO
787-13
General Methods of Test for Pigments - Part 13: Determination of Water-Soluble Sulfates, Chlorides and Nitrates Second Edition
ISO
787-14
General Methods of Test for Pigments and Extenders - Part 14: Determination of Resistivity of Aqueous Extract Second Edition
General Methods of Test for Pigments and Extenders - Part 15: Comparison of Resistance to Light of Coloured Pigments of Similar
ISO
787-15
Types Second Edition; CEN EN ISO 787-15: 1995
General Methods of Test for Pigments and Extenders - Part 16: Determination of Relative Tinting Strength (or Equivalent Colouring
ISO
787-16
Value) and Colour on Reduction of Coloured Pigments - Visual Comparison Method Second Edition; CEN EN ISO 787-16: 1995
ISO
787-17
General Methods of Test for Pigments and Extenders - Part 17: Comparison of Lightening Power of White Pigments Second Edition
General Methods of Test for Pigments and Extenders - Part 18: Determination of Residue on Sieve - Mechanical Flushing Procedure
ISO
787-18
Second Edition; CEN EN ISO 787-18: 1995
ISO
787-19
General Methods of Test for Pigments - Part 19 First Edition; CEN EN ISO 787-19: 1995
General Methods of Test for Pigments and Extenders - Part 21: Comparison of Heat Stability of Pigments Using a Stoving Medium
ISO
787-21
First Edition
ISO
787-22
General Methods of Test for Pigments and Extenders - Part 22: Comparison of Resistance to Bleeding of Pigments First Edition
General Methods of Test for Pigments and Extenders - Part 23: Determination of Density (Using a Centrifuge to Remove Entrained
ISO
787-23
Air) First Edition
General Methods of Test for Pigments and Extenders - Part 24: Determination of Relative Tinting Strength of Coloured Pigments and
ISO
787-24
Relative Scattering Power of White Pigments - Photometric Methods Second Edition; CEN EN ISO 787-24: 1995
General Methods of Test for Pigments and Extenders - Part 25: Comparison of the Colour, in Full-Shade Systems, of White, Black
ISO
787-25
and Coloured Pigments - Colorimetric Method First Edition
ISO
788
Ultramarine Pigments for Paints First Edition
ISO
789-1
Agricultural Tractors - Test Procedures - Part 1: Power Tests for Power Take-Off Second Edition
ISO
789-2
Agricultural Tractors - Test Procedures - Part 2: Rear Three-Point Linkage Lifting Capacity Third Edition
ISO
789-3
Agricultural Tractors - Test Procedures - Part 3: Turning and Clearance Diameters Second Edition
ISO
789-4
Agricultural Tractors - Test Procedures - Part 4: Measurement of Exhaust Smoke Second Edition
ISO
789-5
Agricultural Tractors - Test Procedures - Part 5: Partial Power PTO - Non-Mechanically Transmitted Power First Edition
ISO
789-6
Agricultural Tractors - Test Procedures - Part 6: Centre of Gravity First Edition; Amendment 1-1996
ISO
789-7
Agricultural Tractors - Test Procedures - Part 7: Axle Power Determination First Edition
ISO
789-8
Agricultural Tractors - Test Procedures - Part 8: Engine Air Cleaner First Edition
ISO
789-9
Agricultural Tractors - Test Procedures - Part 9: Power Tests for Drawbar First Edition; Amendment 1-1993
ISO
789-10
Agricultural tractors Test procedures Part 10: Hydraulic power at tractor/implement interface First Edition; Co-Copyrighted by OECD
ISO
789-11
Agricultural Tractors - Test Procedures - Part 11: Steering Capability of Wheeled Tractors First Edition
ISO
789-12
Agricultural Tractors - Test Procedures - Part 12: Low Temperature Starting First Edition
ISO
791
Magnesium Alloys - Determination of Aluminium - 8-Hydroxyquinoline Gravimetric Method First Edition
ISO
792
Magnesium and Magnesium Alloys - Determination of Iron - Orthophenanthroline Photometric Method First Edition
ISO
793
Aluminium and Aluminium Alloys - Determination of Iron - Orthophenanthroline Photometric Method First Edition
ISO
794
Magnesium and Magnesium Alloys - Determination of Copper Content - Oxalyldihydrazide Photometric Method First Edition
ISO
795
Aluminium and Aluminium Alloys - Determination of Copper Content - Oxalyldihydrazide Photometric Method First Edition
ISO
796
Aluminium Alloys - Determination of Copper - Electrolytic Method First Edition
ISO
797
Aluminium and Aluminium Alloys - Determination of Silicon - Gravimetric Method First Edition
ISO
799
Ships and marine technology Pilot ladders Third Edition
ISO
801-1
Pulps - Determination of Saleable Mass in Lots - Part 1: Pulp Baled in Sheet Form Second Edition
ISO
801-2
Pulps - Determination of Saleable Mass in Lots - Part 2: Pulps (Such as Flash-Dried Pulp) Baled in Slabs Second Edition
ISO
801-3
Pulps - Determination of Saleable Mass in Lots - Part 3: Unitized Bales First Edition; Corrected and Reprinted - 1996
ISO
802
Aluminium Oxide Primarily Used for the Production of Aluminium - Preparation and Storage of Test Samples First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Preparation of Solution for Analysis - Method by Alkaline Fusion
ISO
804
First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Iron Content - 1,10-Phenanthroline Photometric
ISO
805
Method First Edition
Aluminium oxide primarily used for the production of aluminium Determination of loss of mass at 300 C and 1 000 C Second
ISO
806
Edition; Supersedes ISO 803
Aluminium and Aluminium Alloys - Determination of Silicon - Spectrophotometric Method with the Reduced Silicomolybdic Complex
ISO
808
First Edition
Magnesium and Magnesium Alloys - Determination of Manganese - Periodate Photometric Method (Manganese Content between
ISO
809
0,01 and 0,8 %) First Edition
Magnesium and Magnesium Alloys - Determination of Manganese - Periodate Photometric Method (Manganese Content Less Than
ISO
810
0,01 %) First Edition
Textile Fabrics - Determination of Resistance to Water Penetration - Hydrostatic Pressure Test First Edition; CAN/CGSB-4.2 NO.
ISO
811
26.3-95
ISO
812
Rubber, vulcanized or thermoplastic Determination of low-temperature brittleness Second Edition
ISO
813
Rubber, Vulcanized or Thermoplastic - Determination of Adhesion to a Rigid Substrate - 90 Degree Peel Method Third Edition
ISO
814
Rubber, vulcanized or thermoplastic ù Determination of adhesion to metal ù Two-plate method Fourth Edition
Rubber, Vulcanized or Thermoplastic - Determination of Compression Set at Ambient, Elevated or Low Temperatures Second
ISO
815
Edition; Corrigendum 1-1993
ISO
817
Refrigerants Designation system Second Edition
ISO
820
Particle Boards - Definition and Classification First Edition
Freight Containers - Vocabulary Conteneurs Pour Le Transport De Marchandises - Vocabulaire Second Edition; Technical
ISO
830
Corrigendum 1: 07/15/2001
Information and Documentation - Bibliographic Description and References - Rules for the Abbreviation of Bibliographic Terms
ISO
832
Second Edition
ISO
834-1
Fire-Resistance Tests - Elements of Building Construction - Part 1: General Requirements First Edition
Fire-Resistance Tests - Elements of Building Construction - Part 4: Specific Requirements for Loadbearing Vertical Separating
ISO
834-4
Elements First Edition
Fire-Resistance Tests - Elements of Building Construction - Part 5: Specific Requirements for Loadbearing Horizontal Separating
ISO
834-5
Elements First Edition
ISO
834-6
Fire-Resistance Tests - Elements of Building Construction - Part 6: Specific Requirements for Beams First Edition
ISO
834-7
Fire-Resistance Tests - Elements of Building Construction - Part 7: Specific Requirements for Columns First Edition
Fire-Resistance Tests - Elements of Building Construction - Part 8: Specific Requirements for Non-Loadbearing Vertical Separating
ISO
834-8
Elements First Edition
ISO
835
Laboratory glassware ù Graduated pipettes First Edition [Replaced: ISO 835-1, ISO 835-2, ISO 835-3, ISO 835-4]
ISO
836
Terminology for Refractories Terminologie Des Materiaux Refractaires First Edition
ISO
839-1
Milling machine arbors with 7/24 tapers Part 1: Dimensions and designation Second Edition
ISO
839-2
Milling Machine Arbors with 7/24 Tapers - Part II: Accessories First Edition
Industrial Automation Systems and Integration - Numerical Control of Machines - Coordinate System and Motion Nomenclature
ISO
841
Second Edition
ISO
844
Rigid cellular plastics ù Determination of compression properties Fifth Edition
ISO
845
Cellular plastics and rubbers Determination of apparent density Third Edition
ISO
846
Plastics - Evaluation of the Action of Microorganisms Second Edition
ISO
855
Oil of lemon [Citrus limon (L.) Burm. f.], obtained by expression Second Edition
ISO
856
Oil of peppermint (Mentha x piperita L.) Second Edition
Welding and Allied Processes - Vocabulary - Part 1: Metal Welding Processes Soudage Et Techniques Connexes - Vocabulaire -
ISO
857-1
Partie 1: Soudage Des Metaux First Edition; Replaces ISO 857
ISO
857-2
Welding and allied processes Vocabulary Part 2: Soldering and brazing processes and related terms First Edition
ISO
860
Terminology Work - Harmonization of Concepts and Terms Second Edition
ISO
862
Surface Active Agents - Vocabulary First Edition; Corrigendum 1-1993; CEN EN ISO 862: 1995
ISO
863
Cement - Test Methods - Pozzolanicity Test for Pozzolanic Cements First Edition
ISO
865
Slots in Platens for Projection Welding Machines First Edition
ISO
866
Centre Drills for Centre Holes without Protecting Chamfers - Type A First Edition
ISO
868
Plastics and Ebonite - Determination of Indentation Hardness by Means of a Durometer (Shore Hardness) Third Edition
ISO
871
Plastics - Determination of Ignition Temperature Using a Hot-Air Furnace Third Edition
ISO
873
Peaches - Guide to Cold Storage First Edition
ISO
874
Fresh Fruits and Vegetables - Sampling First Edition
ISO
875
Essential Oils - Evaluation of Miscibility in Ethanol Second Edition
Plastics - Methods of Exposure to Direct Weathering, to Weathering Using Glass-Filtered Daylight, and to Intensified Weathering by
ISO
877
Daylight Using Fresnel Mirrors Second Edition
Cardamom (Elettaria Cardamomum (Linnaeus) Maton Var. Minuscula Burkill) - Specification - Part 1: Whole Capsules First Edition;
ISO
882-1
Corrigendum 1-1996
Cardamom (Elettaria Cardamomum (Linnaeus) Maton Var. Minuscula Burkill) - Specification - Part 2: Seeds First Edition;
ISO
882-2
Corrigendum 1-1996
ISO
883
Indexable Hardmetal (Carbide) Inserts with Rounded Corners, without Fixing Hole - Dimensions Third Edition
ISO
885
General Purpose Bolts and Screws - Metric Series - Radii under the Head Second Edition
Aluminium and Aluminium Alloys - Determination of Manganese - Photometric Method (Manganese Content between 0,005 and 1,5
ISO
886
%) First Edition
ISO
887
Plain Washers for Metric Bolts, Screws and Nuts for General Purposes - General Plan Second Edition; Corrigendum 1: 01/15/2006
ISO
888
Bolts, Screws and Studs - Nominal Lengths, and Thread Lengths for General Purpose Bolts First Edition
ISO
893
Surface Active Agents - Technical Alkane Sulfonates - Methods of Analysis Second Edition
ISO
894
Surface Active Agents - Technical Sodium Primary Alkylsulphates - Methods of Analysis First Edition
ISO
895
Surface Active Agents - Technical Sodium Secondary Alkylsulfates - Methods of Analysis First Edition
ISO
897
Photography - Roll Films, 126, 110 and 135-Size Films - Identification of the Image-Bearing Side Third Edition
ISO
898-1
Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel - Part 1: Bolts, Screws and Studs Third Edition
ISO
898-2
Mechanical Properties of Fasteners - Part 2: Nuts with Specified Proof Load Values - Coarse Thread Second Edition
Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel - Part 5: Set Screws and Similar Threaded Fasteners Not
ISO
898-5
under Tensile Stresses Second Edition
ISO
898-6
Mechanical Properties of Fasteners - Part 6: Nuts with Specified Proof Load Values - Fine Pitch Thread Second Edition
Mechanical Properties of Fasteners - Part 7: Torsional Test and Minimum Torques for Bolts and Screws with Nominal Diameters 1
ISO
898-7
mm to 10 mm First Edition
ISO
899-1
Plastics - Determination of Creep Behaviour - Part 1: Tensile Creep Second Edition
ISO
899-2
Plastics - Determination of Creep Behaviour - Part 2: Flexural Creep by Three-Point Loading Second Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Titanium Content - Diantipyrylmethane
ISO
900
Photometric Method First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Absolute Density - Pyknometer Method First
ISO
901
Edition
ISO
902
Aluminium Oxide Primarily Used for the Production of Aluminium - Measurement of the Angle of Repose First Edition
ISO
903
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Untamped Density First Edition
ISO
904
Hydrochloric Acid for Industrial Use - Determination of Total Acidity - Titrimetric Method First Edition
Sulphuric Acid and Oleum for Industrial Use - Determination of Total Acidity, and Calculation of Free Sulphur Trioxide Content of
ISO
910
Oleum - Titrimetric Method First Edition
ISO
917
Testing of Refrigerant Compressors Second Edition
ISO
918
Volatile Organic Liquids for Industrial Use - Determination of Distillation Characteristics First Edition
ISO
920
Wool - Determination of Fibre Length (Barbe and Hauteur) Using a Comb Sorter First Edition
ISO
921
Nuclear Energy - Vocabulary Energie Nucleaire - Vocabulaire Second Edition
ISO
924
Coal Preparation Plant - Principles and Conventions for Flowsheets Second Edition
ISO
925
Solid Mineral Fuels - Determination of Carbonate Carbon Content - Gravimetric Method Third Edition
ISO
927
Spices and Condiments - Determination of Extraneous Matter Content Second Edition
ISO
928
Spices and Condiments - Determination of Total Ash Second Edition
ISO
930
Spices and Condiments - Determination of Acid-Insoluble Ash Second Edition
ISO
931
Green Bananas - Guide to Storage and Transport First Edition
ISO
934
Animal and Vegetable Fats and Oils - Determination of Water Content - Entrainment Method First Edition
ISO
935
Animal and Vegetable Fats and Oils - Determination of Titre First Edition
ISO
936
Meat and Meat Products - Determination of Total Ash Second Edition
ISO
937
Meat and Meat Products - Determination of Nitrogen Content (Reference Method) First Edition; PNS 567: 1992
ISO
938
Hand-Operated Stillage Trucks - Principal Dimensions First Edition
ISO
939
Spices and Condiments - Determination of Moisture Content - Entrainment Method First Edition
ISO
941
Spices and Condiments - Determination of Cold Water-Soluble Extract First Edition
ISO
945
Cast Iron - Designation of Microstructure of Graphite First Edition
ISO
946
Grey Cast Iron - Beam Unnotched Impact Test First Edition
ISO
948
Spices and Condiments - Sampling First Edition
ISO
949
Cauliflowers - Guide to Cold Storage and Refrigerated Transport Second Edition
ISO
959-1
Pepper (Piper Nigrum L.), Whole or Ground - Specification - Part 1: Black Pepper Second Edition
ISO
959-2
Pepper (Piper Nigrum L.), Whole or Ground - Specification - Part 2: White Pepper Second Edition
Information Processing - Implementation of the 7-Bit Coded Character Set and Its 7-Bit and 8-Bit Extensions on 9-Track 12,7 mm (0.5
ISO
962
in) Magnetic Tape First Edition
ISO
965-1
ISO General Purpose Metric Screw Threads - Tolerances - Part 1: Principles and Basic Data Third Edition
ISO General Purpose Metric Screw Threads - Tolerances - Part 2: Limits of Sizes for General Purpose External and Internal Screw
ISO
965-2
Threads - Medium Quality Third Edition
ISO
965-3
ISO General Purpose Metric Screw Threads - Tolerances - Part 3: Deviations for Constructional Screw Threads Third Edition
ISO General Purpose Metric Screw Threads - Tolerances - Part 4: Limits of Sizes for Hot-Dip Galvanized External Screw Threads to
ISO
965-4
Mate with Internal Screw Threads Tapped with Tolerance Position H or G After Galvanizing First Edition
ISO General Purpose Metric Screw Threads - Tolerances - Part 5: Limit of Sizes for Internal Screw Threads to Mate with Hot-Dip
ISO
965-5
Galvanized External Screw Threads with Maximum Size of Tolerance Position h Before Galvanizing First Edition
ISO
972
Chillies and Capsicums, Whole or Ground (Powdered) - Specification Second Edition
ISO
973
Pimento (Allspice) [Pimenta Dioica (L.) Merr.], Whole or Ground - Specification Second Edition
ISO
974
Plastics - Determination of the Brittleness Temperature by Impact Second Edition
ISO
975
Brown Coals and Lignites - Determination of Yield of Benzene-Soluble Extract - Semi-Automatic Method Third Edition
Rubber and Plastics - Polymer Dispersions and Rubber Latices - Determination of PH Third Edition; Replaces ISO 1148: 1980;
ISO
976
Amendment 1: 02/01/2006
ISO
979
Sodium Hydroxide for Industrial Use - Method of Assay First Edition
ISO
981
Sodium Hydroxide for Industrial Use - Determination of Chloride Content - Mercurimetric Method First Edition
ISO
999
Information and Documentation - Guidelines for the Content, Organization and Presentation of Indexes Second Edition
ISO
1000
SI Units and Recommendations for the Use of Their Multiples and of Certain Other Units Third Edition; Amendment 1: 11-01-1998
ISO
1001
Information Processing - File Structure and Labelling of Magnetic Tapes for Information Interchange Second Edition
ISO
1002
Rolling Bearings - Airframe Bearings - Characteristics, Boundary Dimensions, Tolerances, Static Load Ratings First Edition
ISO
1003
Spices and Condiments - Ginger, Whole, in Pieces, or Ground - Specification First Edition
ISO
1004
Information Processing - Magnetic Ink Character Recognition - Print Specifications Third Edition
Railway Rolling Stock Material - Part 1: Rough-Rolled Tyres for Tractive and Trailing Stock - Technical Delivery Conditions Third
ISO
1005-1
Edition
Railway Rolling Stock Material - Part 2: Tyres, Wheel Centres and Tyred Wheels for Tractive and Trailing Stock - Dimensional,
ISO
1005-2
Balancing and Assembly Requirements First Edition
ISO
1005-3
Railway Rolling Stock Material - Part 3: Axles for Tractive and Trailing Stock - Quality Requirements First Edition
Railway Rolling Stock Material - Part 4: Rolled or Forged Wheel Centres for Tyred Wheels for Tractive and Trailing Stock - Quality
ISO
1005-4
Requirements First Edition; NZS/ISO 1005.4: 1986
ISO
1005-6
Railway Rolling Stock Material - Part 6: Solid Wheels for Tractive and Trailing Stock - Technical Delivery Conditions Second Edition
ISO
1005-7
Railway Rolling Stock Material - Part 7: Wheelsets for Tractive and Trailing Stock - Quality Requirements First Edition
Railway Rolling Stock Material - Part 8: Solid Wheels for Tractive and Trailing Stock - Dimensional and Balancing Requirements First
ISO
1005-8
Edition
ISO
1005-9
Railway Rolling Stock Material - Part 9: Axles for Tractive and Trailing Stock - Dimensional Requirements First Edition
ISO
1006
Building Construction - Modular Coordination - Basic Module Second Edition; PNS 639: 1988
ISO
1007
Photography - 135-Size Film and Magazine - Specifications Third Edition; Supersedes ANSI IT1.14
ISO
1008
Photography - Paper Dimensions - Pictorial Sheets Second Edition
ISO
1009
Photography - Paper Dimensions - Rolls for Printers Third Edition
ISO
1012
Photography - Films in Sheets and Rolls for General Use - Dimensions Third Edition
ISO
1013
Coke - Determination of Bulk Density in a Large Container Second Edition
Brown coals and lignites Determination of acetone-soluble material (ôresinous substanceö) in the benzene-soluble extract Third
ISO
1017
Edition
ISO
1018
Hard Coal - Determination of Moisture-Holding Capacity First Edition; PNS 289-11: 1990
ISO
1019
Cinematography - Spools, Daylight Loading Type for 16 mm Motion-Picture Cameras - Dimensions Second Edition
ISO
1021
Aircraft - Engine Nacelle Fire Extinguisher Apertures and Doors First Edition
Aerospace - Gaseous Oxygen Replenishment Connection for Use in Fluid Systems (Old Type) - Dimensions (Inch Series) First
ISO
1022
Edition
ISO
1023
Aircraft - High Pressure Air Charging Valves First Edition
Fruit and Vegetable Products - Determination of Dry Matter Content by Drying under Reduced Pressure and of Water Content by
ISO
1026
Azeotropic Distillation First Edition
ISO
1029
Coniferous Sawn Timber - Defects - Classification First Edition
ISO
1030
Coniferous Sawn Timber - Defects - Measurement First Edition
ISO
1031
Coniferous Sawn Timber - Defects - Terms and Definitions First Edition
ISO
1032
Coniferous Sawn Timber - Sizes - Terms and Definitions First Edition
ISO
1033
Aircraft - Dimensions for General Purpose Push-Pull Three-Pole Circuit-Breakers First Edition
ISO
1034
Aircraft - Ground Air-Conditioning Connections First Edition;
ISO
1035-1
Hot-Rolled Steel Bars - Part 1: Dimensions of Round Bars First Edition
ISO
1035-2
Hot-Rolled Steel Bars - Part 2: Dimensions of Square Bars First Edition
ISO
1035-3
Hot-Rolled Steel Bars - Part 3: Dimensions of Flat Bars First Edition; Amendment Slip-1981
ISO
1035-4
Hot-Rolled Steel Bars - Part 4: Tolerances Second Edition
ISO
1036
Textile Machinery - Dyeing and Finishing Machines - Definition of Left and Right Sides Second Edition
ISO
1039
Cinematography - Cores for Motion-Picture and Magnetic Film Rolls - Dimensions Third Edition
ISO
1040
Building Construction - Modular Coordination - Multimodules for Horizontal Coordinating Dimensions Second Edition
ISO
1041
Essential Oils - Determination of Freezing Point First Edition
ISO
1042
Laboratory Glassware - One-Mark Volumetric Flasks Fourth Edition
ISO
1043-1
Plastics - Symbols and Abbreviated Terms - Part 1: Basic Polymers and Their Special Characteristics Third Edition
ISO
1043-2
Plastics - Symbols and Abbreviated Terms - Part 2: Fillers and Reinforcing Materials Second Edition
ISO
1043-3
Plastics - Symbols and Abbreviated Terms - Part 3: Plasticizers Second Edition
ISO
1043-4
Plastics - Symbols and Abbreviated Terms - Part 4: Flame Retardants First Edition
ISO
1044
Industrial Trucks - Lead-Acid Traction Batteries for Electric Trucks - Preferred Voltages Third Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Vibrating Conveyors and Feeders with Rectangular or
ISO
1049
Trapezoidal Trough First Edition
ISO
1050
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Screw Conveyors First Edition
ISO
1051
Rivet Shank Diameters First Edition; Cancels and Replaces ISO Recommendation R 1051: 1969
ISO
1052
Steels for General Engineering Purposes First Edition; Corrected and Reprinted - 1983
ISO
1053
Zinc - Determination of Copper Content - Spectrophotometric Method First Edition
ISO
1054
Zinc - Determination of Cadmium Content - Polarographic Method First Edition
ISO
1055
Zinc and Zinc Alloys - Determination of Iron Content - Spectrophotometric Method First Edition
Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Part 1: Designation System and Basis for Specifications Second
ISO
1060-1
Edition
Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Part 2: Preparation of Test Samples and Determination of
ISO
1060-2
Properties Third Edition
ISO
1061
Plastics - Unplasticized Cellulose Acetate - Determination of Free Acidity Second Edition
ISO
1063
Surface Active Agents - Determination of Stability in Hard Water First Edition
ISO
1064
Surface Active Agents - Determination of Apparent Density of Pastes on Filling First Edition
Non-Ionic Surface-Active Agents Obtained from Ethylene Oxide and Mixed Non-Ionic Surface-Active Agents - Determination of Cloud
ISO
1065
Point Second Edition
ISO
1066
Analysis of Soaps - Determination of Glycerol Content - Titrimetric Method First Edition
ISO
1067
Analysis of Soaps - Determination of Unsaponifiable, Unsaponified and Unsaponified Saponifiable Matter First Edition
ISO
1068
Plastics - PVC Resins - Determination of Compacted Apparent Bulk Density First Edition;
ISO
1069
Magnetic Compasses and Binnacles for Sea Navigation - Vocabulary First Edition
ISO
1070
Liquid Flow Measurement in Open Channels - Slope-Area Method Second Edition; Amendment 1-1997
Welding consumables Covered electrodes, wires, rods and tubular cored electrodes for fusion welding of cast iron Classification
ISO
1071
Second Edition
ISO
1072
Solid Wood Parquet - General Characteristics First Edition
Alphanumeric Character Sets for Optical Recognition - Part 1: Character Set OCR-A - Shapes and Dimensions of the Printed Image
ISO
1073-1
First Edition; Amendment Slip-1978
Alphanumeric Character Sets for Optical Recognition - Part II: Character Set OCR-B - Shapes and Dimensions of the Printed Image
ISO
1073-2
First Edition; Amendment Slip-1978
ISO
1074
Counterbalanced Fork-Lift Trucks - Stability Tests Second Edition
ISO
1080
Machine Tools - Morse Taper Shanks - Cotter Slots with Taper Keys First Edition
ISO
1081
Belt Drives - V-Belts and V-Ribbed Belts, and Corresponding Grooved Pulleys - Vocabulary Second Edition
ISO
1082
Mining - Shackle Type Connector Units for Chain Conveyors Second Edition
ISO
1083
Spheroidal graphite cast irons Classification Third Edition
ISO
1085
Assembly Tools for Screws and Nuts - Double-Ended Wrenches - Size Pairing Third Edition
ISO
1086
Information and Documentation - Title Leaves of Books Second Edition
Terminology Work - Vocabulary - Part 1: Theory and Application Travaux Terminologiques - Vocabulaire - Partie 1: Theorie Et
ISO
1087-1
Application First Edition
Terminology - Vocabulary - Part 2: Computer Applications Terminologie - Vocabulaire - Partie 2: Applications Logicielles First Edition;
ISO
1087-2
Replaces ISO 1087
ISO
1089
Electrode Taper Fits for Spot Welding Equipment - Dimensions First Edition
ISO
1096
Plywood - Classification Second Edition
ISO
1098
Veneer Plywood for General Use - General Requirements First Edition
ISO
1099
Metallic materials Fatigue testing Axial force-controlled method Second Edition
ISO
1100-1
Measurement of Liquid Flow in Open Channels - Part 1: Establishment and Operation of a Gauging Station Second Edition
Measurement of Liquid Flow in Open Channels - Part 2: Determination of the Stage-Discharge Relation Second Edition; Technical
ISO
1100-2
Corrigendum 1: 08/01/2000
Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out Second
ISO
1101
Edition
ISO
1102
Commercial Road Vehicles - 50 mm Drawbar Eye - Interchangeability Thrid Edition
ISO
1103
Road Vehicles - Coupling Balls for Caravans and Light Trailers - Dimensions Fourth Edition
ISO
1104
Surface Active Agents - Technical Sodium Alkylarylsulphonates (Excluding Benzene Derivatives) - Methods of Analysis First Edition
ISO
1107
Fishing nets Netting Basic terms and definitions Second Edition
ISO
1108
Spices and Condiments - Determination of Non-Volatile Ether Extract Second Edition
ISO
1110
Plastics - Polyamides - Accelerated Conditioning of Test Specimens Third Edition
ISO
1112
Horology - Functional and Non-Functional Jewels Second Edition
ISO
1113
Information Processing - Representation of the 7-Bit Coded Character Set on Punched Tape Second Edition
ISO
1114
Cocoa Beans - Cut Test First Edition; PNS 919: 1993
ISO
1118
Aluminium and Aluminium Alloys - Determination of Titanium - Spectrophotometric Chromotropic Acid Method First Edition
ISO
1119
Geometrical Product Specifications (GPS) - Series of Conical Tapers and Taper Angles Second Edition
ISO
1120
Conveyor Belts - Determination of Strength of Mechanical Fastenings - Static Test Method Third Edition
Vocabulary of Gear Terms - Part 1: Definitions Related to Geometry Vocabulaire Des Engrenages - Partie 1: Definitions
ISO
1122-1
Geometriques Second Edition; Corrigendum 1: 11-01-99
Vocabulary of Gear Terms - Part 2: Definitions Related to Worm Gear Geometry Vocabulaire des Engrenages - Partie 2: Definitions
ISO
1122-2
Geometriques Relatives aux Engrenages a Vis First Edition
ISO
1125
Rubber Compounding Ingredients - Carbon Black - Determination of Ash Third Edition
ISO
1126
Rubber compounding ingredients Carbon black Determination of loss on heating Fourth Edition
ISO
1127
Stainless Steel Tubes - Dimensions, Tolerances and Conventional Masses per Unit Length Third Edition
Steel Tubes for Boilers, Superheaters and Heat Exchangers - Dimensions, Tolerances and Conventional Masses per Unit Length
ISO
1129
Second Edition
ISO
1130
Textile Fibres - Some Methods of Sampling for Testing First Edition;
Rolling Bearings - Tolerances Part 1: Terms and Definitions Roulements - Tolerances - Partie 1: Termes Et Definitions First Edition;
ISO
1132-1
Replaces ISO 1132
Rolling Bearings - Tolerances Part 2: Measuring and Gauging Principles and Methods First Edition; Cancels and Replaces ISO/TR
ISO
1132-2
9274:1991
ISO
1133
Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics Fourth edition
ISO
1134
Pears - Cold Storage Second Edition
ISO
1135-3
Transfusion Equipment for Medical Use - Part 3: Blood-Taking Set First Edition
ISO
1135-4
Transfusion equipment for medical use Part 4: Transfusion sets for single use Third Edition
ISO
1136
Wool - Determination of Mean Diameter of Fibres - Air Permeability Method First Edition
ISO
1138
Rubber compounding ingredients ù Carbon black ù Determination of sulfur content Second Edition
ISO
1139
Textiles - Designation of Yarns First Edition
ISO
1140
Fibre ropes Polyamide 3-, 4- and 8-strand ropes Third Edition
ISO
1141
Ropes - Polyester - Specification Third Edition
ISO
1143
Metals - Rotating Bar Bending Fatigue Testing First Edition
Textiles - Universal System for Designating Linear Density (Tex System) First Edition; Replaces ISO R 138: 1960 and ISO R 271:
ISO
1144
1962
ISO
1146
Pyrometric Reference Cones for Laboratory Use - Specification First Edition
ISO
1147
Plastics/Rubber - Polymer Dispersions and Synthetic Rubber Latices - Freeze-Thaw Cycle Stability Test Third Edition
Textile Machinery and Accessories - Drop Wires for Warp Stop Motions for Weaving Machines with Automatic Drawing-In Second
ISO
1150
Edition
ISO
1151-1
Flight Dynamics - Concepts, Quantities and Symbols - Part 1: Aircraft Motion Relative to the Air Fourth Edition
Flight Dynamics - Concepts, Quantities and Symbols - Part 2: Motions of the Aircraft and the Atmosphere Relative to the Earth
ISO
1151-2
Second Edition; Addendum 1-1987
Flight Dynamics - Concepts, Quantities and Symbols - Part 3: Derivatives of Forces, Moments and Their Coefficients Second Edition;
ISO
1151-3
Corrigendum 1-1996
Flight Dynamics - Concepts, Quantities and Symbols - Part 4: Concepts, Quantities and Symbols Used in the Study of Aircraft
ISO
1151-4
Stability and Control Second Edition
ISO
1151-5
Flight Dynamics - Concepts, Quantities and Symbols - Part 5: Quantities Used in Measurements Second Edition
ISO
1151-6
Terms and Symbols for Flight Dynamics - Part 6: Aircraft Geometry Second Edition; Amendment 1-1984
ISO
1151-7
Flight Dynamics - Concepts, Quantities and Symbols - Part 7: Flight Points and Flight Envelopes First Edition
Flight Dynamics - Concepts, Quantities and Symbols - Part 8: Concepts and Quantities Used in the Study of the Dynamic Behaviour
ISO
1151-8
of the Aircraft First Edition
Flight Dynamics - Concepts, Quantities and Symbols - Part 9: Models of Atmospheric Motions Along the Trajectory of the Aircraft First
ISO
1151-9
Edition; Amendment 1 10-01-1998
ISO
1154
Information Processing - Punched Paper Tape - Dimensions and Location of Feed Holes and Code Holes First Edition
ISO
1155
Information Processing - Use of Longitudinal Parity to Detect Errors in Information Messages Second Edition; NZS/ISO 1155: 1978
ISO
1158
Plastics - Vinyl Chloride Homopolymers and Copolymers - Determination of Chlorine Content Third Edition
ISO
1161 AMD 1
Series 1 freight containers ù Corner fittings ù Specification AMENDMENT 1: 45 ft containers Fourth Edition
ISO
1161
Series 1 Freight Containers - Corner Fittings - Specification Fourth Edition; Corrigendum 1-1990; AS/NZS 3711.3: 1993
Plastics - Unplasticized Poly(Vinyl Chloride) (PVC-U) Moulding and Extrusion Materials - Part 1: Designation System and Basis for
ISO
1163-1
Specifications Third Edition
Plastics - Unplasticized Poly(Vinyl Chloride) (PVC-U) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and
ISO
1163-2
Determination of Properties Second Edition
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part
1: General method First Edition; Together with ISO 1167-2 Supersedes ISO 1167: 1996 and Together with ISO 1167-3 Supersedes
ISO
1167-1
ISO 12092: 2000
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part
2: Preparation of pipe test pieces First Edition; Together with ISO 1167-1 Supersedes ISO 1167: 1996 and Together with ISO 1167-3
ISO
1167-2
Supersedes ISO 12092: 2000
ISO
1169
Zinc alloys Determination of aluminium content Titrimetric method Second Edition
ISO
1170
Coal and Coke - Calculation of Analyses to Different Bases First Edition; PNS 289-17: 1990
ISO
1171
Solid Mineral Fuels - Determination of Ash Content Third Edition; Technical Corrigendum 1: 11-15-1998
Textile-Glass-Reinforced Plastics - Prepregs, Moulding Compounds and Laminates - Determination of the Textile-Glass and Mineral-
ISO
1172
Filler Content - Calcination Methods Second Edition
Assembly Tools for Screws and Nuts - Drive Ends for Hand- and Machine-Operated Screwdriver Bits and Connecting Parts -
ISO
1173
Dimensions, Torque Testing Third Edition
ISO
1174-1
Assembly Tools for Screws and Nuts - Driving Squares - Part 1: Driving Squares for Hand Socket Tools First Edition
ISO
1174-2
Assembly Tools for Screws and Nuts - Driving Squares - Part 2: Driving Squares for Power Socket Tools First Edition
ISO
1176
Road Vehicles - Masses - Vocabulary and Codes Second Edition
ISO
1177
Information Processing - Character Structure for Start/Stop and Synchronous Character Oriented Transmission Second Edition
ISO
1178
Magnesium Alloys - Determination of Soluble Zirconium - Alizarin Sulphonate Photometric Method Second Edition
Connections for general use and fluid power ù Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing
ISO
1179-1
ù Part 1: Threaded ports First Edition [Replaced: ISO 1179]
Connections for general use and fluid power ù Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing
ISO
1179-2
ù Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) First Edition [Replaced: ISO 1179]
Connections for general use and fluid power ù Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing
ISO
1179-3
ù Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) First Edition [Replaced: ISO 1179]
Connections for general use and fluid power ù Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing
ISO
1179-4
ù Part 4: Stud ends for general use only with metal-to-metal sealing (type B) First Edition [Cancelled: ISO 1179]
ISO
1180
Shanks for Pneumatic Tools and Dimensions of Chuck Bushings First Edition; Addendum 1-1985; NZS/ISO 1180: 1983
ISO
1181
Fibre ropes Manila and sisal 3-, 4- and 8-strand ropes Third Edition
ISO
1182
Reaction to Fire Tests for Building Products - Non-Combustibility Test Fourth Edition
Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and
ISO
1183-1
titration method First Edition; Together with 1183-2 and 1183-3 replaces 1183:1987
Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method First Edition; Replaces
ISO
1183-2
ISO 1183:1987
ISO
1183-3
Plastics - Methods for Determining the Density of Non-Cellular Plastics - Part 3: Gas Pyknometer Method First Edition
Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 24 N (normal) for
ISO
1185
vehicles with 24 V nominal supply voltage Third Edition
Cinematography - Recorded Characteristic for Magnetic Sound on Full-Coat 16 mm Motion-Picture Film - Specifications Second
ISO
1188
Edition
Cinematography - Recorded Characteristic for Magnetic Sound Records on 35 mm Motion-Picture Film Excluding Striped Release
ISO
1189
Prints - Specifications Second Edition
ISO
1190-1
Copper and Copper Alloys - Code of Designation - Part 1: Designation of Materials First Edition
ISO
1198
Sealed-Beam Landing Lamps for Aircraft - Dimensions First Edition
ISO
1203
Photography - Roll Film Cameras - Back Window Location Fourth Edition
Reciprocating Internal Combustion Engines - Designation of the Direction of Rotation and of Cylinders and Valves in Cylinder Heads,
ISO
1204
and Definition of Right-Hand and Left-Hand In-Line Engines and Locations on an Engine Second Edition
ISO
1206
Rolling Bearings - Needle Roller Bearings, Dimension Series 48,49 and 69 - Boundary Dimensions and Tolerances Third Edition
ISO
1207
Slotted Cheese Head Screws - Product Grade A Third Edition; CEN EN ISO 1207
ISO
1208
Spices and Condiments - Determination of Filth First Edition
ISO
1209-1
Rigid cellular plastics ù Determination of flexural properties ù Part 1: Basic bending test Third Edition
Rigid cellular plastics Determination of flexural properties Part 2: Determination of flexural strength and apparent flexural modulus of
ISO
1209-2
elasticity Third Edition
ISO
1211
Milk - Determination of Fat Content - Gravimetric Method (Reference Method) Second Edition
ISO
1212
Apples - Cold Storage Second Edition
ISO
1213-1
Solid Mineral Fuels - Vocabulary - Part 1: Terms Relating to Coal Preparation Second Edition
ISO
1213-2
Solid Mineral Fuels - Vocabulary - Part 2: Terms Relating to Sampling, Testing and Analysis First Edition
ISO
1215
Commercially Dry Virgin Cork, Ramassage, Gleanings, Corkwood Refuse and Corkwaste - Definitions and Packaging Second Edition
ISO
1216
Corkwood in Planks - Grading, Classification and Packing Third Edition
ISO
1217
Displacement Compressors - Acceptance Tests Third Edition; BS 1571: Part 1: 1987; NZS/BS 1571: PT 1: 1987
Fluid power systems and components Graphic symbols and circuit diagrams Part 1: Graphic symbols for conventional use and data-
ISO
1219-1
processing applications Second Edition
ISO
1219-2
Fluid Power Systems and Components - Graphic Symbols and Circuit Diagrams - Part 2: Circuit Diagrams First Edition
ISO
1222 CORR 1
Photography ù Tripod connections TECHNICAL CORRIGENDUM 1 Third Edition
ISO
1222
Photography - Tripod Connections Third Edition
ISO
1223
Cinematography - Picture Areas for Motion-Picture Films for Television - Position and Dimensions Fourth Edition
Rolling bearings ù Instrument precision bearings ù Part 1: Boundary dimensions, tolerances and characteristics of metric series
ISO
1224-1
bearings First Edition [Cancelled: ISO 1224]
Rolling bearings ù Instrument precision bearings ù Part 2: Boundary dimensions, tolerances and characteristics of inch series
ISO
1224-2
bearings FIRST EDITION [Cancelled: ISO 1224]
ISO
1230
Photography - Determination of Flash Guide Numbers Third Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Silica Content - Reduced Molybdosilicate
ISO
1232
Spectrophotometric Method First Edition
ISO
1234
Split Pins Second Edition
ISO
1237
Mustard Seed - Specification Second Edition
Essential Oils - Determination of Ester Values, Before and After Acetylation, and Evaluation of the Contents of Free and Total
ISO
1241
Alcohols Second Edition
ISO
1242
Essential Oils - Determination of Acid Value Second Edition
ISO
1247
Aluminium Pigments for Paints First Edition; Amendment 1-1982
ISO
1248 TECH COR
Iron oxide pigments Specifications and methods of test
ISO
1248
Iron oxide pigments Specifications and methods of test Second Edition
Zinc Chromate Pigments - Basic Zinc Potassium Chromate Pigments and Zinc Tetrahydroxychromate Pigments First Edition;
ISO
1249
Corrigendum 1-1992
ISO
1264
Plastics - Homopolymer and Copolymer Resins of Vinyl Chloride - Determination of pH of Aqueous Extract Second Edition
ISO
1265
Plastics ù Poly(vinyl chloride) resins ù Determination of number of impurities and foreign particles Second Edition
ISO
1268-1
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 1: General Conditions First Edition
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 2: Contact and Spray-Up Moulding First Edition; Cancels and
ISO
1268-2
Replaces ISO 1268: 1974
ISO
1268-3
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 3: Wet Compression Moulding First Edition
ISO
1268-4
Fibre-reinforced plastics Methods of producing test plates Part 4: Moulding of prepregs First Edition; Replaces ISO 9353: 1991
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 5: Filament Winding First Edition; Cancels and Replaces ISO
ISO
1268-5
9291:1996
ISO
1268-6
Fibre-Reinforced Plastics Methods of Producing Test Plates Part 6: Pultrusion Moulding First Edition
ISO
1268-7
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 7: Resin Transfer Moulding First Edition
ISO
1268-8
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 8: Compression moulding of SMC and BMC First Edition
ISO
1268-9
Fibre-Reinforced Plastics - Methods of Producing Test Plates - Part 9: Moulding of GMT/STC First Edition
Fibre-reinforced plastics Methods of producing test plates Part 10: Injection moulding of BMC and other long-fibre moulding
ISO
1268-10
compounds General principles and moulding of multipurpose test specimens First Edition; Replaces ISO 1268: 1974
Fibre-reinforced plastics Methods of producing test plates Part 11: Injection moulding of BMC and other long-fibre moulding
ISO
1268-11
compounds Small plates First Edition; Replaces ISO 1268: 1974
ISO
1269
Plastics Homopolymer and copolymer resins of vinyl chloride Determination of volatile matter (including water) Third Edition
ISO
1271
Essential Oils - Determination of Carbonyl Value - Free Hydroxylamine Method Second Edition; Corrected and Reprinted - 1985
ISO
1272
Essential Oils - Determination of Content of Phenols Second Edition
ISO
1275
Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors Fourth Edition
ISO
1279
Essential Oils - Determination of Carbonyl Value - Potentiometric Methods Using Hydroxylammonium Chloride Third Edition
ISO
1302
Geometrical Product Specifications (GPS) - Indication of Surface Texture in Technical Product Documentation Fourth Edition
ISO
1304
Rubber compounding ingredients Carbon black Determination of iodine adsorption number Fourth Edition
ISO
1306
Rubber Compounding Ingredients - Carbon Black (Pelletized) - Determination of Pour Density Fourth Edition
Rubber and plastics hoses Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses Fourth
ISO
1307
Edition
ISO
1324
Solid Wood Parquet - Classification of Oak Strips First Edition
Cylindrical Gears - ISO System of Accuracy - Part 1: Definitions and Allowable Values of Deviations Relevant to Corresponding
ISO
1328-1
Flanks of Gear Teeth First Edition; Corrected and Reprinted - 02/01/1997
Cylindrical Gears - ISO System of Accuracy - Part 2: Definitions and Allowable Values of Deviations Relevant to Radial Composite
ISO
1328-2
Deviations and Runout Information First Edition
ISO
1340
Cylindrical Gears - Information to Be Given to the Manufacturer by the Purchaser in Order to Obtain the Gear Required First Edition
Straight Bevel Gears - Information to Be Given to the Manufacturer by the Purchaser in Order to Obtain the Gear Required First
ISO
1341
Edition
ISO
1342
Oil of Rosemary (Rosmarinus Officinalis Linnaeus) Second Edition
Fibre ropes Polypropylene split film, monofilament and multifilament (PP2) and polypropylene high tenacity multifilament (PP3) 3-, 4-
ISO
1346
and 8-strand ropes Third Edition
ISO
1352
Steel - Torsional Stress Fatigue Testing First Edition
ISO
1361
Light-Gauge Metal Containers - Round Open-Top Cans - Internal Diameters Fourth Edition
ISO
1382
Rubber - Vocabulary Caoutchouc - Vocabulaire Fourth Edition
ISO
1385-1
Phthalate Esters for Industrial Use - Methods of Test - Part I: General First Edition
ISO
1388-1
Ethanol for Industrial Use - Methods of Test - Part 1: General First Edition
ISO
1388-2
Ethanol for Industrial Use - Methods of Test - Part 2: Detection of Alkalinity or Determination of Acidity to Phenolphthalein First Edition
Ethanol for Industrial Use - Methods of Test - Part 3: Estimation of Content of Carbonyl Compounds Present in Small Amounts -
ISO
1388-3
Photometric Method First Edition
Ethanol for Industrial Use - Methods of Test - Part 4: Estimation of Content of Carbonyl Compounds Present in Moderate Amounts -
ISO
1388-4
Titrimetric Method First Edition
ISO
1388-5
Ethanol for Industrial Use - Methods of Test - Part 5: Determination of Aldehydes Content - Visual Colorimetric Method First Edition
ISO
1388-6
Ethanol for Industrial Use - Methods of Test - Part 6: Test for Miscibility with Water First Edition
Ethanol for Industrial Use - Methods of Test - Part 7: Determination of Methanol Content (Methanol Contents between 0,01 and 0,20
ISO
1388-7
% (V/V)) - Photometric Method First Edition
Ethanol for Industrial Use - Methods of Test - Part 8: Determination of Methanol Content (Methanol Contents between 0,10 and 1,50
ISO
1388-8
% (V/V)) - Visual Colorimetric Method First Edition
Ethanol for Industrial Use - Methods of Test - Part 9: Determination of Esters Content - Titrimetric Method After Saponification First
ISO
1388-9
Edition
ISO
1388-10
Ethanol for Industrial Use - Methods of Test - Part 10: Estimation of Hydrocarbons Content - Distillation Method First Edition
ISO
1388-11
Ethanol for Industrial Use - Methods of Test - Part 11: Test for Detection of Furfural First Edition
ISO
1388-12
Ethanol for Industrial Use - Methods of Test - Part 12: Determination of Permanganate Time First Edition
ISO
1392
Determination of Crystallizing Point - General Method First Edition
ISO
1401
Rubber Hoses for Agricultural Spraying Third Edition
ISO
1402
Rubber and Plastic Hoses and Hose Assemblies - Hydrostatic Testing Third Edition; CEN EN ISO 1402: 1996
ISO
1403
Rubber Hoses, Textile-Reinforced, for General-Purpose Water Applications - Specification Fourth edition
ISO
1407 CORR 1
Rubber ù Determination of solvent extract
ISO
1407
Rubber - Determination of Solvent Extract Second Edition
ISO
1408
Rubber - Determination of Carbon Black Content - Pyrolytic and Chemical Degradation Methods Third Edition
Plastics/rubber Polymer dispersions and rubber latices (natural and synthetic) Determination of surface tension by the ring method
ISO
1409
Fifth Edition
ISO
1413
Horology - Shock-Resistant Watches Second Edition
ISO
1419
Rubber- or Plastics-Coated Fabrics - Accelerated-Ageing Tests Second Edition
ISO
1420
Rubber- or Plastics-Coated Fabrics - Determination of Resistance to Penetration by Water Third Edition
ISO
1421
Rubber- or Plastics-Coated Fabrics - Determination of Tensile Strength and Elongation at Break Second Edition
Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing Fourth Edition; Replaces
ISO
1431-1
ISO 1431-2: 1/15/1994
Rubber, Vulcanized or Thermoplastic - Resistance to Ozone Cracking - Part 3: Reference and Alternative Methods for Determining
ISO
1431-3
the Ozone Concentration in Laboratory Test Chambers First Edition
Rubber, Vulcanized or Thermoplastic - Determination of Low Temperature Stiffening (Gehman Test) Third Edition; Corrigendum 1:
ISO
1432
8/1/2003
ISO
1434
Natural Rubber in Bales - Amount of Bale Coating - Determination Second Edition
ISO
1435
Rubber Compounding Ingredients - Carbon Black (Pelletized) - Determination of Fines Content Fourth Edition
Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 1: Oil-based fluid applications First
ISO
1436-1
Edition
Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types Specification Part 2: Water-based fluid applications First
ISO
1436-2
Edition
ISO
1437
Rubber compounding ingredients ù Carbon black ù Determination of sieve residue Fourth edition
Water Flow Measurement in Open Channels Using Weirs and Venturi Flumes - Part 1: Thin-Plate Weirs First Edition; Amendment 1-
ISO
1438-1
1998
ISO
1442
Meat and Meat Products - Determination of Moisture Content (Reference Method) Second Edition
ISO
1443
Meat and Meat Products - Determination of Total Fat Content First Edition; PNS 570: 1992
ISO
1444
Meat and Meat Products - Determination of Free Fat Content Second Edition
ISO
1446
Green Coffee - Determination of Water Content Basic Reference Method Second Edition
ISO
1456
Metallic Coatings - Electrodeposited Coatings of Nickel Plus Chromium and of Copper Plus Nickel Plus Chromium Third Edition
ISO
1458
Metallic coatings Electrodeposited coatings of nickel Third Edition
Metallic Coatings - Hot Dip Galvanized Coatings on Ferrous Materials - Gravimetric Determination of the Mass per Unit Area Second
ISO
1460
Edition
ISO
1461
Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles - Specifications and Test Method Second Edition
ISO
1463
Metallic and Oxide Coatings - Measurement of Coating Thickness - Microscopical Method Third Edition
ISO
1464
Aerospace - Tripod Jacks - Clearance Dimensions Second Edition
ISO
1465
Aircraft - Liquid Oxygen Replenishment Couplings - Mating Dimensions Second Edition
ISO
1466
Lever-Operated Manual Switches for Aircraft - Performance Requirements First Edition
ISO
1467
General Purpose Push-Pull Single-Pole Circuit-Breakers for Aircraft - Performance Requirements First Edition
ISO
1478
Tapping Screws Thread Second Edition
ISO
1479
Hexagon Head Tapping Screws First Edition; CEN EN ISO 1479: 1994; AS/NZS 4402: 1996
ISO
1481
Slotted Pan Head Tapping Screws First Edition; CEN EN ISO 1481: 1994; AS/NZS 4403: 1996
ISO
1482
Slotted Countersunk (Flat) Head Tapping Screws (Common Head Style) First Edition; CEN EN ISO 1482: 1994; AS/NZS 4404: 1996
Slotted Raised Countersunk (Oval) Head Tapping Screws (Common Head Style) First Edition; CEN EN ISO 1483: 1994; AS/NZS
ISO
1483
4405: 1996
Series 1 freight containers Specification and testing Part 1: General cargo containers for general purposes Fifth Edition; Amendment
ISO
1496-1
1: 03/01/93; Amendment 2: 07/01/98; Amendment 3: 06/15/05; Amendment 5: 05/15/06; Amendment 4: 11/01/06
ISO
1496-2
Series 1 Freight Containers - Specification and Testing - Part 2: Thermal Containers Fourth Edition; Amendment 1: 02/01/2006
Series 1 Freight Containers - Specification and Testing - Part 3: Tank Containers for Liquids, Gases and Pressurized Dry Bulk Fourth
ISO
1496-3
Edition; Amendment 1: 02/01/2006
Series 1 Freight Containers - Specification and Testing - Part 4: Non-Pressurized Containers for Dry Bulk First Edition; Amendment 1-
ISO
1496-4
1994; Technical Corrigendum 1: 03/01/2006
Series 1 Freight Containers - Specification and Testing - Pt 5: Platform and Platform-Based Containers Amendment 1: 1AAA and
ISO
1496-5
1BBB Containers Second Edition; Amendment 1-1993; Amendment 2-1994; AS/NZS 3711.8: 1993; PNS 924-5: 1992
ISO
1502
ISO General-Purpose Metric Screw Threads - Gauges and Gauging Second Edition
ISO
1503
Geometrical Orientation and Directions of Movements First Edition
ISO
1505
Textile Machinery - Widths Relating to Dyeing and Finishing Machines - Definitions and Range of Nominal Widths Second Edition
ISO
1506
Textile Machinery - Dyeing, Finishing and Allied Machinery - Classification and Nomenclature First Edition
ISO
1509
General Purpose Push-Pull Three-Pole Circuit-Breakers for Aircraft - Performance Requirements First Edition
Paints and Varnishes - Examination and Preparation of Samples for Testing Third Edition; Corrigendum 1-1994; CEN EN ISO 1513:
ISO
1513
1994; AS/NZS 1580.103.1: 1995
ISO
1514
Paints and Varnishes - Standard Panels for Testing Fourth Edition
ISO
1516
Determination of Flash/No Flash Test - Closed Cup Equilibrium Method Third Edition
ISO
1517
Paints and Varnishes - Surface-Drying Test - Ballotini Method First Edition
ISO
1518
Paints and Varnishes - Scratch Test Second Edition
ISO
1519
Paints and Varnishes - Bend Test (Cylindrical Mandrel) Second Edition
ISO
1520
Paints and Varnishes - Cupping Test Third Edition
ISO
1522
Paints and Varnishes - Pendulum Damping Test Third Edition
ISO
1523
Determination of Flashpoint - Closed Cup Equilibrium Method Third Edition
ISO
1524
Paints, Varnishes and Printing Inks - Determination of Fineness of Grind Third Edition
ISO
1530
Fishing Nets - Description and Designation of Knotted Netting Second Edition
ISO
1531
Fishing Nets - Hanging of Netting - Basic Terms and Definitions First Edition
ISO
1532
Fishing Nets - Cutting Knotted Netting to Shape (Tapering") First Edition"
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Troughed Belt Conveyors (Other Than Portable Conveyors) -
ISO
1535
Belts First Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Troughed Belt Conveyors (Other Than Portable Conveyors) -
ISO
1536
Belt Pulleys First Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Troughed Belt Conveyors (Other Than Portable Conveyors) -
ISO
1537
Idlers First Edition
ISO
1539-1 CORR 2
Information Technology - Programming Languages - Fortran - Part 1: Basic Language Second Edition
ISO
1539-1 CORR 1
Information technology ù Programming languages ù Fortran ù Part 1: Base language Second edition
ISO
1539-1
Information Technology - Programming Languages - Fortran - Part 1: Basic Language Second Edition
ISO
1539-2
Information Technology - Programming Languages - FORTRAN - Part 2: Varying Length Character Strings Second Edition
Information Technology - Programming Languages - Fortran - Part 3: Conditional Compilation First Edition; Corrected and Reprinted
ISO
1539-3
12/15/2000
ISO
1540
Aerospace - Characteristics of Aircraft Electrical Systems Third Edition
ISO
1546
Procedure for Milk Recording for Cows First Edition
ISO
1547
Aircraft - Precision Fuse-Links - General Requirements First Edition
ISO
1548
Aircraft - Precision Fuse-Links - Type A First Edition
ISO
1549
Aircraft - Precision Fuse-Links - Type B First Edition
ISO
1552
Liquid Chlorine for Industrial Use - Method of Sampling (for Determining Only the Volumetric Chlorine Content) First Edition
ISO
1553
Unalloyed Copper Containing Not Less Than 99,90 % of Copper - Determination of Copper Content - Electrolytic Method First Edition
ISO
1554
Wrought and Cast Copper Alloys - Determination of Copper Content - Electrolytic Method First Edition
ISO
1559
Dental Materials - Alloys for Dental Amalgam Third Edition; Corrigendum 1: 1997 [Replaced By: ISO 24234]
ISO
1560
Dental Mercury Second Edition; CAN/CSA-Z349.17-M92 [Replaced By: ISO 24234]
ISO
1563
Dental Alginate Impression Material Second Edition; CAN/CSA-Z349.38-93
ISO
1564
Dental Aqueous Impression Materials Based on Agar Second Edition; CAN/CSA-Z349.20-M92
ISO
1567
Dentistry - Denture Base Polymers Third Edition; Amendment 1: 09/01/2003
ISO
1570
Zinc and Zinc Alloys - Determination of Tin Content - Spectrophotometric Method First Edition
ISO
1572
Tea - Preparation of Ground Sample of Known Dry Matter Content Second Edition
ISO
1573
Tea - Determination of Loss in Mass at 103 Degrees C Second Edition
ISO
1575
Tea - Determination of Total Ash Third Edition
ISO
1576
Tea - Determination of Water-Soluble Ash and Water-Insoluble Ash Second Edition
ISO
1577
Tea - Determination of Acid-Insoluble Ash Second Edition
ISO
1578
Tea - Determination of Alkalinity of Water-Soluble Ash First Edition
ISO
1580
Slotted Pan Head Screws - Product Grade A Second Edition; CEN EN ISO 1580: 1994
ISO
1585
Road Vehicles - Engine Test Code - Net Power Third Edition
ISO
1586
Textile Machinery and Accessories - Shuttles - Terms and Designation in Relation to the Position of the Shuttle Eye First Edition
ISO
1587
Gypsum Rock for the Manufacture of Binders - Specifications First Edition
ISO
1598
Plastics - Cellulose Acetate - Determination of Insoluble Particles Second Edition
ISO
1599
Plastics - Cellulose Acetate - Determination of Viscosity Loss on Moulding Second Edition
Plastics - Cellulose Acetate - Determination of Light Absorption on Moulded Specimens Produced Using Different Periods of Heating
ISO
1600
Second Edition
ISO
1604
Belt Drives - Endless Wide V-Belts for Industrial Speed-Changers and Groove Profiles for Corresponding Pulleys Second Edition
Positive-Displacement Vacuum Pumps - Measurement of Performance Characteristics - Part 1: Measurement of Volume Rate of
ISO
1607-1
Flow (Pumping Speed) Second Edition
Positive-Displacement Vacuum Pumps - Measurement of Performance Characteristics - Part 2: Measurement of Ultimate Pressure
ISO
1607-2
Second Edition
Vapour Vacuum Pumps - Measurement of Performance Characteristics - Part 1: Measurement of Volume Rate of Flow (Pumping
ISO
1608-1
Speed) Second Edition
Vapour Vacuum Pumps - Measurement of Performance Characteristics - Part 2: Measurement of Critical Backing Pressure Second
ISO
1608-2
Edition
ISO
1609
Vacuum Technology - Flange Dimensions First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Sodium Content - Flame Emission
ISO
1617
Spectrophotometric Method First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Vanadium Content - N-Benzoyl-N-
ISO
1618
Phenylhydroxylamine Photometric Method First Edition
ISO
1619
Cryolite, Natural and Artificial - Preparation and Storage of Test Samples First Edition
ISO
1620
Cryolite, Natural and Artificial - Determination of Silica Content - Reduced Molybdosilicate Spectrophotometric Method First Edition
Plastics - Polystyrene (PS) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications Second
ISO
1622-1
Edition
Plastics - Polystyrene (PS) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of Properties
ISO
1622-2
Second Edition
ISO
1624
Plastics - Vinyl Chloride Homopolymer and Copolymer Resins - Sieve Analysis in Water Second Edition
Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 1: General Principles
ISO
1628-1
Second Edition
Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 2: Poly(Vinyl Chloride) Resins
ISO
1628-2
Second Edition
Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 3: Polyethylenes and
ISO
1628-3
Polypropylenes Second Edition
Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 4: Polycarbonate (PC)
ISO
1628-4
Moulding and Extrusion Materials Second Edition
Plastics - Determination of the Viscosity of Polymers in Dilute Solution Using Capillary Viscometers - Part 5: Thermoplastic Polyester
ISO
1628-5
(TP) Homopolymers and Copolymers Second Edition
ISO
1628-6
Plastics - Determination of Viscosity Number and Limiting Viscosity Number - Part 6: Methyl Methacrylate Polymers First Edition
ISO
1629
Rubber and Latices - Nomenclature Third Edition
ISO
1641-1
End Mills and Slot Drills - Part 1: Milling Cutters with Cylindrical Shanks Second Edition
ISO
1641-2
End Mills and Slot Drills - Part II: Milling Cutters with Morse Taper Shanks First Edition
ISO
1641-3
End Mills and Slot Drills - Part 3: Milling Cutters with 7/24 Taper Shanks Second Edition
ISO
1651
Tube Drawing Mandrels First Edition; Amendment 1-1982
ISO
1652
Rubber latex Determination of apparent viscosity by the Brookfield test method Third Edition
ISO
1656
Rubber, Raw Natural, and Rubber Latex, Natural - Determination of Nitrogen Content Third Edition
ISO
1657
Rubber, Raw and Rubber Latex - Determination of Iron Content - 1,10-Phenanthroline Photometric Method Second Edition
ISO
1658
Natural Rubber (NR) - Evaluation Procedure Second Edition
ISO
1660
Technical Drawings - Dimensioning and Tolerancing of Profiles Second Edition; CEN EN ISO 1660: 1995
ISO
1663
Rigid cellular plastics ù Determination of water vapour transmission properties Third edition
ISO
1666
Starch - Determination of Moisture Content - Oven-Drying Method Second Edition
ISO
1673
Onions - Guide to Storage Second Edition
ISO
1675
Plastics - Liquid Resins - Determination of Density by the Pyknometer Method Second Edition
ISO
1680
Acoustics - Test Code for the Measurement of Airborne Noise Emitted by Rotating Electrical Machines First Edition
ISO
1681
Information Processing - Unpunched Paper Cards - Specification First Edition
ISO
1683
Acoustics - Preferred Reference Quantities for Acoustic Levels First Edition; BS EN 21683; CEN EN 21683: 1994
ISO
1684
Wire, Bar and Tube Drawing Dies - Specifications First Edition; Amendment 2-1982
ISO
1686
Sodium and Potassium Silicates for Industrial Use - Samples and Method of Test - General First Edition
ISO
1689
Sodium and Potassium Silicates for Industrial Use - Calculation of the Ratio SiO2/Na2O or SiO2/K2O First Edition
Sodium and Potassium Silicates for Industrial Use - Determination of Silica Content - Gravimetric Method by Insolubilization First
ISO
1690
Edition
ISO
1691
Sodium and Potassium Silicates for Industrial Use - Determination of Carbonates Content - Gas-Volumetric Method First Edition
ISO
1692
Sodium and Potassium Silicates for Industrial Use - Determination of Total Alkalinity - Titrimetric Method First Edition
ISO
1693
Cryolite, Natural and Artificial - Determination of Fluorine Content - Modified Willard-Winter Method First Edition
ISO
1694
Cryolite, Natural and Artificial - Determination of Iron Content - 1,10-Phenanthroline Photometric Method First Edition
ISO
1700
Cinematography - 8 mm Type S Motion-Picture Raw Stock Film - Cutting and Perforating Dimensions Third Edition
Test conditions for milling machines with table of variable height Testing of the accuracy Part 1: Machines with horizontal spindle
ISO
1701-1
First Edition; Replaces ISO 1701-0: 6/1/1984 and ISO 1701-3:12/15/97
Test Conditions for Milling Machines with Table of Variable Height - Testing of Accuracy - Part 2: Machines with Horizontal Spindle
ISO
1701-2
Second Edition; Replaces ISO 1701-0: 6/1/1984 and ISO 1701-3: 12/15/1997
Assembly tools for screws and nuts Designation and nomenclature Outils de manoeuvre pour vis et Úcrous DÚsignation et
ISO
1703
nomenclature Third Edition
ISO
1704
Shipbuilding - Stud-Link Anchor Chains Second Edition
ISO
1708
Acceptance Conditions for General Purpose Parallel Lathes - Testing of the Accuracy Fourth Edition
ISO
1709
Nuclear Energy - Fissile Materials - Principles of Criticality Safety in Storing, Handling and Processing Second Edition
ISO
1711-1
Assembly tools for screws and nuts ù Technical specifications ù Part 1: Hand-operated wrenches and sockets Second Edition
ISO
1711-2
Assembly tools for screws and nuts - Technical specifications - Part 2: Machine-operated sockets (impact") First Edition"
ISO
1716
Reaction to Fire Tests for Building Products - Determination of the Heat of Combustion Second Edition
ISO
1717
Rock Drilling - Rotary Drill-Rods and Rotary Drill-Bits for Dry Drilling - Connecting Dimensions First Edition
ISO
1718
Rock Drilling Equipment - Drill Rods with Tapered Connection for Percussive Drilling Second Edition
Rock Drilling - Extension Drill-Steel Equipment for Percussive Long-Hole Drilling - Reverse-Buttress-Threaded Equipments 1 1/16
ISO
1721
and (27 and 32 mm) First Edition
Rock Drilling - Extension Drill-Steel Equipment for Percussive Long-Hole Drilling - Reverse-Buttress-Threaded Equipments 1 1/2 to 2
ISO
1722
1/2 in (38 to 64 mm) First Edition
Road vehicles Connectors for the electrical connection of towing and towed vehicles 7-pole connector type 12 N (normal) for
ISO
1724
vehicles with 12 V nominal supply voltage Fourth Edition
Road vehicles ù Mechanical couplings between tractors and semi-trailers ù Part 2: Interchangeability between low-coupling tractors
ISO
1726-2
and high-volume semi-trailers First edition
ISO
1726 CORR 1
Road Vehicles - Mechanical Coupling between Tractors and Semi-Trailers - Interchangeability
ISO
1726
Road Vehicles - Mechanical Coupling between Tractors and Semi-Trailers - Interchangeability Third Edition
ISO
1728
Road vehicles Pneumatic braking connections between motor vehicles and towed vehicles Interchangeability Third Edition
ISO
1730
Dictation Equipment - Basic Operating Requirements Second Edition
ISO
1735
Cheese and processed cheese products Determination of fat content Gravimetric method (Reference method) Third Edition; IDF 5
ISO
1736
Dried Milk and Dried Milk Products - Determination of Fat Content - Gravimetric Method (Reference Method) Third Edition
Evaporated Milk and Sweetened Condensed Milk - Determination of Fat Content - Gravimetric Method (Reference Method) Third
ISO
1737
Edition
ISO
1738
Butter - Determination of Salt Content Third Edition; IDF 12
ISO
1739
Butter - Determination of the Refractive Index of the Fat (Reference Method) Second Edition; IDF 7: 2006
ISO
1740
Milkfat products and butter - determination of fat acidity (Reference method) Third edition
ISO
1741
Dextrose - Determination of Loss in Mass on Drying - Vacuum Oven Method First Edition; CEN EN ISO 1741: 1994
ISO
1742
Glucose Syrups - Determination of Dry Matter - Vacuum Oven Method First Edition
ISO
1743
Glucose Syrup - Determination of Dry Matter Content - Refractive Index Method Second Edition
ISO
1745
Information Processing - Basic Mode Control Procedures for Data Communication Systems First Edition
ISO
1746
Rubber or Plastics Hoses and Tubing - Bending Tests Third Edition; Corrigendum 1: 05/01/1999
ISO
1749
Aircraft - Elastomeric Sealing Rings - Packaging and Identification First Edition
Pesticides and Other Agrochemicals - Common Names Produits Phytosanitaires Et Assimiles - Noms Communs First Edition;
Amendment 1-1982; Addendum 1-1983; Addendum 2-1983; Replaces ISO R 116: 1959 and ISO R 219: 1961 and ISO R 258: 1962;
ISO
1750
Amendment 2: 11-15-99; Amendment 3 12/01/2001
ISO
1751
Shipbuilding and Marine Structures - Ships Side Scuttles Second Edition
ISO
1754
Photography - Cameras Using 35 mm Film and Roll Film - Picture Sizes Fourth Edition; Corrigendum 1: 03/01/2002
ISO
1755
Photography - Projector Slides - Dimensions Second Edition
ISO
1756
Industrial Trucks - Dimensions of Stillages - Connection Gauge First Edition
ISO
1757
Personal Photographic Dosemeters Second Edition
ISO
1762
Paper, Board and Pulps - Determination of Residue (Ash) on Ignition at 525 Degrees C Second Edition
ISO
1763
Carpets - Determination of Number of Tufts and/or Loops per Unit Length and per Unit Area Second Edition; AS/NZS 2111.9: 1996
ISO
1765
Machine-Made Textile Floor Coverings - Determination of Thickness Second Edition; AS/NZS 2111.1: 1996
ISO
1766
Textile Floor Coverings - Determination of Thickness of Pile Above the Substrate Third Edition
Glass Hydrometers - Conventional Value for the Thermal Cubic Expansion Coefficient (for Use in the Preparation of Measurement
ISO
1768
Tables for Liquids) First Edition
ISO
1769
Laboratory Glassware - Pipettes - Colour Coding First Edition
ISO
1770
Solid-Stem General Purpose Thermometers First Edition; Amendment 1-1983
ISO
1771
Enclosed-Scale General Purpose Thermometers First Edition; Amendment 1-1983
ISO
1772
Laboratory Crucibles in Porcelain and Silica First Edition
ISO
1773
Laboratory Glassware - Narrow-Necked Boiling Flasks Second Edition
ISO
1775
Porcelain Laboratory Apparatus - Requirements and Methods of Test First Edition
Glass - Resistance to Attack by Hydrochloric Acid at 100 Degrees Celsius - Flame Emission or Flame Atomic Absorption
ISO
1776
Spectrometric Method First Edition
Cinematography - Motion-Picture Camera Cartridge, 8 mm Type S Model I - Aperture, Camera Aperture Profile, Film Position,
ISO
1780
Pressure Pad and Pressure Pad Flatness - Dimensions and Specifications Second Edition; Corrected and Reprinted - 1984
ISO
1781
Cinematography - Projector Usage of 8 mm Type S Motion-Picture Film for Direct Front Projection Second Edition
ISO
1783
Magnesium Alloys - Determination of Zinc - Volumetric Method First Edition
ISO
1784
Aluminium Alloys - Determination of Zinc - EDTA Titrimetric Method First Edition
Cinematography - Printed 8 mm, Type S, Image Area on 16 mm Motion-Picture Film Perforated 8 mm, Type S (1-4) - Position and
ISO
1785
Dimensions Second Edition
ISO
1787
Cinematography - Camera Usage of 8 mm Type S Motion-Picture Film - Specifications Second Edition
ISO
1791
Building Construction - Modular Coordination - Vocabulary Second Edition; PNS 637: 1988
Cinematography - Reels for 16 mm Motion-Picture Projectors (up to and Including 610 m Capacity: 38 cm Size) - Dimensions Second
ISO
1793
Edition
ISO
1795
Rubber, Raw Natural and Raw Synthetic - Sampling and Further Preparative Procedures Fourth Edition
ISO
1797-1
Dental Rotary Instruments - Shanks - Part 1: Shanks Made of Metals First Edition; Amendment 1-1997
ISO
1797-2
Dental Rotary Instruments - Shanks - Part 2: Shanks Made of Plastics First Edition; CAN/CSA-Z349.50.2-94
Flexible Cellular Polymeric Materials - Determination of Tensile Strength and Elongation at Break Third Edition; Corrigendum 1:
ISO
1798
3/15/2003
ISO
1802
Natural Rubber Latex Concentrate - Determination of Boric Acid Content Third Edition
Building Construction - Tolerances - Expression of Dimensional Accuracy - Principles and Terminology First Edition; Cancels and
ISO
1803
Replaces ISO 4464: 1980
ISO
1804
Doors - Terminology First Edition
ISO
1805
Fishing nets Determination of breaking force and knot breaking force of netting yarns Second Edition
ISO
1806
Fishing Nets - Determination of Mesh Breaking Load of Netting Second Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Oscillating Conveyors and Shaking or Reciprocating Feeders
ISO
1807
with Rectangular or Trapezoidal Trough First Edition
ISO
1809
Textile Machinery and Accessories - Types of Formers for Yarn Packages - Nomenclature First Edition
ISO
1810
Copper Alloys - Determination of Nickel (Low Contents) - Dimethylglyoxime Spectrophotometric Method First Edition
Copper and Copper Alloys - Selection and Preparation of Samples for Chemical Analysis - Part 1: Sampling of Cast Unwrought
ISO
1811-1
Products First Edition
Copper and Copper Alloys - Selection and Preparation of Samples for Chemical Analysis - Part 2: Sampling of Wrought Products and
ISO
1811-2
Castings First Edition
ISO
1812
Copper Alloys - Determination of Iron Content - 1,10-Phenanthroline Spectrophotometric Method First Edition
Belt Drives - V-Ribbed Belts, Joined V-Belts and V-Belts Including Wide Section Belts and Hexagonal Belts - Electrical Conductivity of
ISO
1813
Antistatic Belts: Characteristics and Methods of Test Third Edition; Corrected and Reprinted 04/15/1999
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Vibrating Feeders and Conveyors with Tubular Trough First
ISO
1815
Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials and Unit Loads - Belt Conveyors - Basic Characteristics of
ISO
1816
Motorized Driving Pulleys First Edition
ISO
1817
Rubber, Vulcanized - Determination of the Effect of Liquids Fourth Edition; Corrected Version 2/15/2006
ISO
1819
Continuous Mechanical Handling Equipment - Safety Code - General Rules First Edition
ISO
1823-1
Rubber Hoses and Hose Assemblies - Part 1: On-Shore Oil Suction and Discharge - Specification First Edition
ISO
1823-2
Rubber Hoses and Hose Assemblies - Part 2: Ship/Dockside Discharge - Specification First Edition
ISO
1825
Rubber Hoses and Hose Assemblies for Aircraft Ground Fuelling and Defuelling - Specification Second Edition
Rubber, vulcanized or thermoplastic - Determination of shear modulus and adhesion to rigid plates - Quadruple-shear methods Third
ISO
1827
Edition
ISO
1829
Selection of Tolerance Zones for General Purposes First Edition
ISO
1830
Paper, board and pulps Determination of acid-soluble manganese Second Edition
ISO
1831
Printing Specifications for Optical Character Recognition First Edition
ISO
1832 CORR 1
Indexable inserts for cutting tools ù Designation TECHNICAL CORRIGENDUM 1 Fourth Edition
ISO
1832
Indexable inserts for cutting tools ù Designation Fourth Edition
Textiles Quantitative chemical analysis Part 1: General principles of testing First Edition;:1977; Together with ISO 1833-3 thru ISO
ISO
1833-1
1833-19 replaces ISO 1833:1977
ISO
1833-2
Textiles Quantitative chemical analysis Part 2: Ternary fibre mixtures First Edition;: 1976 [Replaced: ISO 5088]
Textiles Quantitative chemical analysis Part 3: Mixtures of acetate and certain other fibres (method using acetone) First Edition;
ISO
1833-3
Together with ISO 1833-1: 2006, ISO 1833-4 thru ISO 1833-19: 2006 replaces ISO 1833: 1977
Textiles Quantitative chemical analysis Part 4: Mixtures of certain protein and certain other fibres (method using hypochlorite) First
ISO
1833-4
Edition; Together with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-19: 2006 replaces ISO 1833: 1977
Textiles Quantitative chemical analysis Part 5: Mixtures of viscose, cupro or modal and cotton fibres (method using sodium zincate)
First Edition; Together with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-4: 2006, ISO 1833-6 thru ISO 1833-19: 2006 replaces ISO
ISO
1833-5
1833: 1977
Textiles ù Quantitative chemical analysis ù Part 6: Mixtures of viscose or certain types of cupro or modal or lyocell and cotton fibres
ISO
1833-6
(method using formic acid and zinc chloride) First Edition
Textiles Quantitative chemical analysis Part 7: Mixtures of polyamide and certain other fibres (method using formic acid) First
Edition; Together with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-6: 2006, ISO 1833-8 thru ISO 1833-19: 2006 replaces ISO 1833:
ISO
1833-7
1977
Textiles Quantitative chemical analysis Part 8: Mixtures of acetate and triacetate fibres (method using acetone) First Edition;
ISO
1833-8
Together with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-7: 2006, ISO 1833-9 thru ISO 1833-19: 2006 replaces ISO 1833: 1977
Textiles Quantitative chemical analysis Part 9: Mixtures of acetate and triacetate fibres (method using benzyl alcohol) First Edition;
ISO
1833-9
Together with ISO 1833-1:2006, ISO 1833-3 thru ISO 1833-8:2006, ISO 1833-10 thru ISO 1833-19:2006 replaces ISO 1833:1977
Textiles Quantitative chemical analysis Part 10: Mixtures of triacetate or polylactide and certain other fibres (method using
dichloromethane) First Edition; Together with ISO 1833-1 thru ISO 1833-9 and ISO 1833-11 thru ISO 1883-19 Supersedes ISO
ISO
1833-10
1833:77
Textiles Quantitative chemical analysis Part 11: Mixtures of cellulose and polyester fibres (method using sulfuric acid) First Edition;
ISO
1833-11
Together with ISO 1833-1 thru ISO 1833-10 and ISO 1833-12 thru ISO 1883-19 Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 12: Mixtures of acrylic, certain modacrylics, certain chlorofibres, certain elastanes and
certain other fibres (method using dimethylformamide) First Edition; Together with ISO 1833-1 thru ISO 1833-11 and ISO 1833-13
ISO
1833-12
thru ISO 1883-19 Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 13: Mixtures of certain chlorofibres and certain other fibres (method using carbon
disulfide/acetone) First Edition; Together with ISO 1833-1 thru ISO 1833-12 and ISO 1833-14 thru ISO 1883-19 Supersedes ISO
ISO
1833-13
1833:77
Textiles Quantitative chemical analysis Part 14: Mixtures of acetate and certain chlorofibres (method using acetic acid) First Edition;
ISO
1833-14
Together with ISO 1833-1 thru ISO 1833-13 and ISO 1833-15 thru ISO 1883-19 Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 15: Mixtures of jute and certain animal fibres (method by determining nitrogen content)
ISO
1833-15
First Edition; Together with ISO 1833-1 thru ISO 1833-14 and ISO 1833-16 thru ISO 1883-19 Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 16: Mixtures of polypropylene fibres and certain other fibres (method using xylene) First
ISO
1833-16
Edition; Together with ISO 1833-1 thru ISO 1833-15 and ISO 1833-17 thru ISO 1883-19 Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 17: Mixtures of chlorofibres (homopolymers of vinyl chloride) and certain other fibres
(method using sulfuric acid) First Edition; Together with ISO 1833-1 thru ISO 1833-16 and ISO 1833-18 thru ISO 1883-19
ISO
1833-17
Supersedes ISO 1833:77
Textiles Quantitative chemical analysis Part 18: Mixtures of silk and wool or hair (method using sulfuric acid) First Edition; Together
ISO
1833-18
with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-17: 2006 and ISO 1833-19: 2006 replaces ISO 1833: 1977
Textiles - Quantitative chemical analysis - Part 19: Mixtures of cellulose fibres and asbestos (method by heating) First Edition;
ISO
1833-19
Together with ISO 1833-1: 2006, ISO 1833-3 thru ISO 1833-18: 2006 replaces ISO 1833: 1977
Textiles Quantitative chemical analysis Part 21: Mixtures of chlorofibres, certain modacrylics, certain elastanes, acetates, triacetates
ISO
1833-21
and certain other fibres (method using cyclohexanone) First Edition
ISO
1834
Short Link Chain for Lifting Purposes - General Conditions of Acceptance Second Edition
ISO
1835
Short Link Chain for Lifting Purposes - Grade M (4), Non-Calibrated, for Chain Slings, Etc. First Edition
ISO
1837
Lifting Hooks - Nomenclature Second Edition
ISO
1838
Fresh Pineapples - Storage and Transport Second Edition
ISO
1839
Tea - Sampling First Edition
ISO
1840
Definitions of Living Animals for Slaughter - Porcines First Edition
ISO
1841-1
Meat and Meat Products - Determination of Chloride Content - Part 1: Volhard Method First Edition; Replaces ISO 1841
ISO
1841-2
Meat and Meat Products - Determination of Chloride Content - Part 2: Potentiometric Method First Edition; Replaces ISO 1841
ISO
1842
Fruit and Vegetable Products - Determination of pH Second Edition
ISO
1853
Conducting and Dissipative Rubbers, Vulcanized or Thermoplastic - Measurement of Resistivity Second Edition
ISO
1854
Whey Cheese - Determination of Fat Content - Gravimetric Method (Reference Method) Third Edition
ISO
1856 AMD 1
Flexible cellular polymeric materials ù Determination of compression set Third Edition
ISO
1856
Flexible Cellular Polymeric Materials - Determination of Compression Set Third Edition
Information Processing - General Purpose Hubs and Reels, with 76 mm (3 in) Centrehole, for Magnetic Tape Used in Interchange
ISO
1858
Instrumentation Applications First Edition
Information Processing - Unrecorded Magnetic Tapes for Interchange Instrumentation Applications - General Dimensional
ISO
1859
Requirements First Edition
ISO
1860
Information Processing - Precision Reels for Magnetic Tape Used in Interchange Instrumentation Applications Third Edition
Information Processing - 7-Track, 12,7 mm (0.5 in) Wide Magnetic Tape for Information Interchange Recorded at 8 rpmm (200 rpi)
ISO
1861
First Edition
Information Processing - 9-Track, 12,7 mm (0.5 in) Wide Magnetic Tape for Information Interchange Recorded at 8 rpmm (200 rpi)
ISO
1862
First Edition
Information Processing - 9-Track, 12,7 mm (0,5 in) Wide Magnetic Tape for Information Interchange Using NRZ1 at 32 ftpmm (800
ISO
1863
ftpi) - 32 cpmm (800 cpi) Second Edition
Information Technology - Unrecorded 12,7 mm (0,5 in) Wide Magnetic Tape for Information Interchange - 32 ftpmm (800 ftpi), NRZ1,
ISO
1864
126 ftpmm (3 200 ftpi) Phase Encoded and 356 ftpmm (9 042 ftpi), NRZ1 Fourth Edition; CEN EN 21864: 1993
Textile Machinery and Accessories - Serrated Bars for Mechanical Warp Stop Motions - Designations of Dimensions, and
ISO
1865
Dimensions of Cross-Section First Edition
ISO
1871
Agricultural Food Products - General Directions for the Determination of Nitrogen by the Kjeldahl Method First Edition
Plastics - Polyethylene (PE) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications Second
ISO
1872-1
Edition
Plastics ù Polyethylene (PE) moulding and extrusion materials ù Part 2: Preparation of test specimens and determination of
ISO
1872-2
properties Third Edition
Plastics - Polypropylene (PP) Moulding and Extrusion Materials - Part 1: Designation System and Basis for Specifications Fourth
ISO
1873-1
Edition; CEN EN ISO 1873-1: 1995
Plastics - Polypropylene (PP) Moulding and Extrusion Materials - Part 2: Preparation of Test Specimens and Determination of
ISO
1873-2
Properties Third Edition
ISO
1874-1
Plastics - Polyamide (PA) Moulding and Extrusion Materials - Part 1: Designation Second Edition; Corrected and Reprinted - 1992
Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO
1874-2
Third Edition
ISO
1875
Plastics - Plasticized Cellulose Acetate - Determination of Matter Extractable by Diethyl Ether First Edition
ISO
1887
Textile Glass - Determination of Combustible-Matter Content Third Edition
ISO
1888
Textile glass Staple fibres or filaments Determination of average diameter Third Edition
ISO
1889
Reinforcement Yarns - Determination of Linear Density Third Edition; Replaces ISO 10120: 1991
ISO
1890
Reinforcement Yarns - Determination of Twist Third Edition
ISO
1891
Bolts, Screws, Nuts and Accessories - Terminology and Nomenclature First Edition; Amendment Slip-1980
ISO
1893
Refractory products ù Determination of refractoriness under load ù Differential method with rising temperature Third Edition
Road Vehicles - M14 X 1,25 Spark-Plugs with Flat Seating and Their Cylinder Head Housings Fifth Edition; Technical Corrigendum 1:
ISO
1919
02-15-1999
ISO
1920
Concrete Tests - Dimensions, Tolerances and Applicability of Test Specimens First Edition [Replaced By: ISO 1920-3]
ISO
1920-1
Testing of concrete Part 1: Sampling of fresh concrete First Edition; Replaces ISO 2736-1:1986
Testing of concrete Part 2: Properties of fresh concrete First Edition; Replaces ISO 4109:1980, ISO 4110:1979, ISO 4111:1979, ISO
ISO
1920-2
4848:1980, ISO 6276:1982
ISO
1920-3
Testing of concrete Part 3: Making and curing test specimens First Edition; [Replaced: ISO 1920, ISO 2736-2]
Testing of concrete - Part 4: Strength of hardened concrete First Edition; Replaces ISO 4012:1978, ISO 4013:1978 and ISO
ISO
1920-4
4108:1980
ISO
1920-5
Testing of concrete Part 5: Properties of hardened concrete other than strength First Edition; Replaces ISO 6275:1982
ISO
1920-6
Testing of concrete Part 6: Sampling, preparing and testing of concrete cores First Edition
ISO
1920-7
Testing of concrete Part 7: Non-destructive tests on hardened concrete First Edition
ISO
1922
Rigid Cellular Plastics - Determination of Shear Strength Third Edition
Cellular Plastics and Rubbers - Determination of Linear Dimensions Second Edition; CEN PREN 21923: 1994; CEN EN ISO 1923:
ISO
1923
1995
Paper and Board - Determination of Tensile Properties - Part 2: Constant Rate of Elongation Method Second Edition; CEN EN ISO
ISO
1924-2
1924-2: 1995
ISO
1924-3
Paper and board Determination of tensile properties Part 3: Constant rate of elongation method (100 mm/min) First Edition
ISO
1925
Mechanical Vibration - Balancing - Vocabulary Vibrations Mecaniques - Equilibrage - Vocabulaire Fourth Edition
ISO
1926
Rigid cellular plastics Determination of tensile properties Third Edition
ISO
1927
Prepared Unshaped Refractory Materials (Dense and Insulating) - Classification Second Edition
Solid Mineral Fuels - Determination of Gross Calorific Value by the Bomb Calorimetric Method, and Calculation of Net Calorific Value
ISO
1928
Second Edition
ISO
1929
Abrasive Belts - Dimensions, Tolerances and Designation Second Edition
Mechanical vibration ù Balance quality requirements for rotors in a constant (rigid) state ù Part 1: Specification and verification of
ISO
1940-1 CORR 1
balance tolerances TECHNICAL CORRIGENDUM 1 Second Edition
Mechanical vibration ù Balance quality requirements for rotors in a constant (rigid) state ù Part 1: Specification and verification of
ISO
1940-1
balance tolerances Second Edition
ISO
1940-2
Mechanical Vibration - Balance Quality Requirements of Rigid Rotors - Part 2: Balance Errors First Edition
Dental Vocabulary - Part 1: General and Clinical Terms Second Edition; Amendment 1-1992; Amendment 2-1992; Amendment 3-
ISO
1942-1
1993; Amendment 5-1993; PNS 1248-1: 1994
ISO
1942-2
Dental Vocabulary - Part 2: Dental Materials Second Edition; Amendment 1-2: 1992; CEN EN 21942-2: 1992; PNS 1248-2: 1994
ISO
1942-3
Dental Vocabulary - Part 3: Dental Instruments Second Edition; Amendment 1-2: 1992; PNS 1248-3: 1994
ISO
1942-4
Dental Vocabulary - Part 4: Dental Equipment Second Edition; Amendment 1-1992; CEN EN 21942-4: 1993; PNS 1248-4: 1994
ISO
1942-5
Dental Vocabulary - Part 5: Terms Associated with Testing Second Edition; CEN EN ISO 1942-5: 1994; PNS 1248-5: 1994
Photography - Front Lens Barrels up to 127 mm - Dimensions Important to the Connection of Auxiliaries Second Edition; ANSI
ISO
1948
PH3.104-1992
ISO
1949
Aircraft - Electrical Connectors - Design Requirements Second Edition
ISO
1950
Aircraft - Identification of Servicing, Maintenance, Ground Handling and Safety/Hazard Points First Edition
ISO
1951
Presentation/representation of entries in dictionaries ù Requirements, recommendations and information Third Edition
Brown Coals and Lignites - Method of Extraction for the Determination of Sodium and Potassium Soluble in Dilute Hydrochloric Acid
ISO
1952
First Edition
ISO
1953
Hard Coal - Size Analysis by Sieving Second Edition
ISO
1954
1999 Plywood - Tolerances on Dimensions First Edition
ISO
1955
Citrus Fruits and Derived Products - Determination of Essential Oils Content (Reference Method) First Edition
ISO
1956-1
Fruits and Vegetables - Morphological and Structural Terminology - Part 1 First Edition
ISO
1956-2
Fruits and Vegetables - Morphological and Structural Terminology - Part 2 First Edition
ISO
1957
Machine-Made Textile Floor Coverings - Selection and Cutting of Specimens for Physical Tests Third Edition
ISO
1964
Shipbuilding - Indication of Details on the General Arrangement Plans of Ships Second Edition
ISO
1965
Aluminium Terminal Ends for Crimping to Aircraft Aluminium Electrical Cables First Edition
ISO
1966
Crimped Joints for Aircraft Electrical Cables First Edition
ISO
1967
Aircraft - Fire-Resisting Electrical Cables - Dimensions, Conductor Resistance and Mass First Edition
ISO
1968
Fibre ropes and cordage Vocabulary Cordages en fibres et articles de corderie Vocabulaire Fourth Edition
ISO
1969
Fibre ropes Polyethylene 3- and 4-strand ropes Third Edition
ISO
1971
Aircraft - Accessory Drives and Mounting Pads First Edition
Textile Fibres - Determination of Linear Density - Gravimetric Method and Vibroscope Method Second Edition; CEN EN ISO 1973:
ISO
1973
1995
ISO
1974
Paper - Determination of Tearing Resistance (Elmendorf Method) Third Edition; CEN EN 21974: 1994; PNS 316: 1989)
Magnesium and Magnesium Alloys - Determination of Silicon - Spectrophotometric Method with the Reduced Silicomolybdic Complex
ISO
1975
First Edition
ISO
1976
Zinc Alloys - Determination of Copper Content - Electrolytic Method First Edition
ISO
1977
Conveyor chains, attachments and sprockets Second Edition
Test Conditions for Manually Controlled Milling Machines with Table of Fixed Height - Testing of the Accuracy - Part 1: Machines with
ISO
1984-1
Horizontal Spindle First Edition; Together with ISO 1984-2:2001, Cancels and Replaces ISO 1984:1982 and ISO 1984-0:1984
Test Conditions for Manually Controlled Milling Machines with Table of Fixed Height - Testing of the Accuracy - Part 2: Machines with
ISO
1984-2
Vertical Spindle First Edition; Together with ISO 1984-1:2001, Cancels and Replaces ISO 1984:1982 and ISO 1984-0:1984
Machine Tools - Test Conditions for Surface Grinding Machines with Vertical Grinding Wheel Spindle and Reciprocating Table -
ISO
1985
Testing of the Accuracy Third Edition
Test Conditions for Surface Grinding Machines with Horizontal Grinding Wheel Spindle and Reciprocating Table - Testing of
ISO
1986-1
Accuracy - Part 1: Machines with a Table Length of up to 1 600 mm First Edition; Replaces ISO 1986
ISO
1988
Hard Coal - Sampling First Edition; Amendment-1975
ISO
1989 CORR 2
Information technology ù Programming languages ù COBOL TECHNICAL CORRIGENDUM 2 First Edition
ISO
1989 CORR 1
Information technology Programming languages COBOL TECHNICAL CORRIGENDUM 1 First Edition
ISO
1989
Information technology Programming languages COBOL First Edition
ISO
1990-1
Fruits - Nomenclature - First List First Edition; PNS 1147-1: 1993
ISO
1990-2
Fruits - Nomenclature - Second List First Edition; PNS 1146: 1993
ISO
1991-1
Vegetables - Nomenclature - First List First Edition; PNS 1145: 1993
ISO
1991-2
Vegetables - Nomenclature - Part 2: Second List Second Edition
ISO
1992-2
Commercial Refrigerated Cabinets - Methods of Test - Part 2: General Test Conditions First Edition; Amendment 1-1979
ISO
1992-3
Commercial Refrigerated Cabinets - Methods of Test - Part 3: Temperature Test First Edition; Amendment 1-1980
ISO
1992-8
Commercial Refrigerated Cabinets - Test Methods - Part VIII: Test for Accidental Mechanical Contact First Edition
ISO
1995
Aromatic Hydrocarbons - Sampling First Edition
Acoustics Description, measurement and assessment of environmental noise Part 1: Basic quantities and assessment procedures
ISO
1996-1
Second Edition
Acoustics ù Description, measurement and assessment of environmental noise ù Part 2: Determination of environmental noise levels
ISO
1996-2
Second Edition [Replaced: ISO 1996-1, ISO 1996-1, ISO 1996-3]
ISO
1997
Granulated Cork and Cork Powder - Classification, Properties and Packing Second Edition
Petroleum Industry - Terminology - Part 1: Raw Materials and Products Industrie Petroliere - Terminologie - Parte 1: Matieres
ISO
1998-1
Premieres Et Produits Second Edition; Corrigendum 1 07/15/1999
Petroleum Industry - Terminology - Part 2: Properties and Tests Industrie Petroliere - Terminologie - Partie 2: Proprietes Et Essais
ISO
1998-2
Second Edition
Petroleum Industry - Terminology - Part 3: Exploration and Production Industrie Petroliere - Terminologie - Partie 3: Exploration Et
ISO
1998-3
Production First Edition
ISO
1998-4
Petroleum Industry - Terminology - Part 4: Refining Industrie Petroliere - Terminologie - Partie 4: Raffinage First Edition
Petroleum Industry - Terminology - Part 5: Transport, Storage, Distribution Industrie Petroliere - Terminologie - Parte 5: Transport,
ISO
1998-5
Stockage, Distribution First Edition; Corrigendum 1 07/15/1999
ISO
1998-6
Petroleum Industry - Terminology - Part 6: Measurement Industrie Petroliere - Terminologie - Partie 6: Mesurage First Edition
Petroleum Industry - Terminology - Part 7: Miscellaneous Terms Industrie Petroliere - Terminologie - Partie 7: Termes Divers First
ISO
1998-7
Edition
Petroleum Industry - Terminology - Part 99: General and Index Industrie Petroliere - Terminologie - Partie 99: Generalites Et Index
ISO
1998-99
First Edition
ISO
1999
Acoustics - Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment Second Edition
ISO
2000
Rubber, raw natural Guidelines for the specification of technically specified rubber (TSR) Sixth Edition
ISO
2004
Natural Rubber Latex Concentrate - Centrifuged or Creamed, Ammonia-Preserved Types - Specification Fourth Edition
ISO
2005
Rubber Latex, Natural, Concentrate - Determination of Sludge Content Third Edition; Amendment 1: 02/01/2006
ISO
2006
Rubber Latex, Synthetic - Determination of High-Speed Mechanical Stability Second Edition
ISO
2007
Rubber, Unvulcanized - Determination of Plasticity - Rapid-Plastimeter Method Fourth Edition
ISO
2009
Slotted Countersunk Flat Head Screws (Common Head Style) - Product Grade A Third Edition; CEN EN ISO 2009: 1994
ISO
2010
Countersunk Slotted Raised Head Screws (Common Head Style) - Product Grade A Third Edition; CEN EN ISO 2010: 1994
ISO
2012
Textile Machinery and Accessories - Cone Sectional Warping Machines - Maximum Usable Width First Edition
ISO
2016
Capillary Solder Fittings for Copper Tubes - Assembly Dimensions and Tests First Edition
Mechanical vibration and shock Resilient mounting systems Part 1: Technical information to be exchanged for the application of
ISO
2017-1
isolation systems First Edition; Together with ISO 2017-2 Replaces ISO 2017: 1982
Aerospace - Preformed Flexible Steel Wire Rope for Aircraft Controls - Part 1: Dimensions and Loads First Edition; Together with ISO
ISO
2020-1
2020-2, It Cancels and Replaces ISO 2020: 1984; Reprinted 12/01/1997
Aerospace - Preformed Flexible Steel Wire Rope for Aircraft Controls - Part 2: Technical Specification First Edition; Together with ISO
ISO
2020-2
2020-1, It Cancels and Replaces ISO 2020: 1984; Reprinted 12/01/1997
ISO
2022
Information Technology - Character Code Structure and Extension Techniques Fourth Edition; Technical Corrigendum 1: 04/15/1999
ISO
2023
Rubber Footwear - Lined Industrial Vulcanized-Rubber Boots - Specification Second Edition: Corrigendum 1: 12/15/2002
ISO
2026
Aircraft - Connections for Starting Engines by Air First Edition
ISO
2027
Natural Rubber Latex Concentrate, Evaporated, Preserved - Specification Third Edition
ISO
2028
Synthetic Rubber Latex - Preparation of Dry Polymer Fourth Edition
ISO
2030
Granulated Cork - Size Analysis by Mechanical Sieving Second Edition
ISO
2031
Granulated Cork - Determination of Bulk Density Second Edition
ISO
2032
Heat-Resisting Equipment Wires for Aircraft First Edition
ISO
2033
Information Processing - Coding of Machine Readable Characters (MICR and OCR) Second Edition
Unplasticized Polyvinyl Chloride (PVC) Moulded Fittings for Elastic Sealing Ring Type Joints for Use under Pressure - Pressure-
ISO
2035
Resistance Test First Edition
ISO
2036
Wood for Manufacture of Wood Flooring - Symbols for Marking According to Species First Edition
ISO
2037
Stainless Steel Tubes for the Food Industry Second Edition
ISO
2039-1
Plastics - Determination of Hardness - Part 1: Ball Indentation Method Third Edition
ISO
2039-2
Plastics - Determination of Hardness - Part 2: Rockwell Hardness Second Edition
ISO
2040
Strontium Chromate Pigments for Paints First Edition
ISO
2041
Vibration and Shock - Vocabulary Second Edition
ISO
2042
Aircraft Electrical Circuit Diagrams First Edition
Unplasticized Polyvinyl Chloride (PVC) Injection-Moulded Solvent-Welded Socket Fittings for Use with Pressure Pipe - Hydraulic
ISO
2044
Internal Pressure Test First Edition
Single Sockets for Unplasticized Poly(Vinyl Chloride) (PVC-U) and Chlorinated Poly(Vinyl Chloride) (PVC-C) Pressure Pipes with
ISO
2045
Elastic Sealing Ring Type Joints - Minimum Depths of Engagement Second Edition
ISO
2046
Gaseous Breathing Oxygen Supplies for Aircraft First Edition
ISO
2047
Information Processing - Graphical Representations for the Control Characters of the 7-Bit Coded Character Set First Edition
Double-Socket Fittings for Unplasticized Poly(Vinyl Chloride) (PVC-U) Pressure Pipes with Elastic Sealing Ring Type Joints -
ISO
2048
Minimum Depths of Engagement Second Edition
ISO
2049
Petroleum Products - Determination of Colour (ASTM Scale) Second Edition
ISO
2057
Agricultural Tractors - Remote Control Hydraulic Cylinders for Trailed Implements Second Edition
ISO
2060
Textiles - Yarn from Packages - Determination of Linear Density (Mass per Unit Length) by the Skein Method Second Edition
ISO
2061
Textiles - Determination of Twist in Yarns - Direct Counting Method Second Edition; CEN EN ISO 2061: 1995
Textiles - Yarns from Packages - Determination of Single-End Breaking Force and Elongation at Break Second Edition; Corrected
ISO
2062
and Reprinted - 1995; CEN EN ISO 2062: 1995
ISO
2063
Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys Third Edition
Metallic and Other Inorganic Coatings - Definitions and Conventions Concerning the Measurement of Thickness Third Edition; CEN
ISO
2064
EN ISO 2064: 1994; PNS 670: 1990
ISO
2066
Resilient floor coverings Determination of moisture content of agglomerated composition cork Third Edition
ISO
2067
Granulated Cork - Sampling Third Edition
ISO
2068
Barium Chromate Pigments for Paints First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Calcium Content - Flame Atomic Absorption
ISO
2069
Method First Edition
ISO
2070
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Calcium Content Second Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Zinc Content - Flame Atomic Absorption Method
ISO
2071
First Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Determination of Zinc Content - PAN Photometric Method First
ISO
2072
Edition
Aluminium Oxide Primarily Used for the Production of Aluminium - Preparation of Solution for Analysis - Method by Hydrochloric Acid
ISO
2073
Attack under Pressure First Edition
ISO
2074
Plywood - Vocabulary First Edition
ISO
2076
Textiles - Man-Made Fibres - Generic Names Fourth Edition
ISO
2077
Pure Expanded Corkboard - Determination of the Modulus of Rupture by Bending First Edition;
ISO
2078
Textile Glass - Yarns - Designation Fifth Edition; CEN EN ISO 2078: 1994
ISO
2079
Surface Treatment and Metallic Coatings - General Classification of Terms Second Edition
ISO
2080
Electroplating and Related Processes - Vocabulary Second Edition
ISO
2081
Metallic Coatings - Electroplated Coatings of Zinc on Iron or Steel Second Edition
ISO
2082
Metallic Coatings - Electroplated Coatings of Cadmium on Iron or Steel Second Edition
ISO
2085
Anodizing of Aluminium and Its Alloys - Check of Continuity of Thin Anodic Oxide Coatings - Copper Sulphate Test First Edition
ISO
2093
Electroplated Coatings of Tin - Specification and Test Methods Second Edition
ISO
2094
Textile Floor Coverings - Determination of Thickness Loss under Dynamic Loading Third Edition
ISO
2096
Glycerols for Industrial Use - Methods of Sampling First Edition
ISO
2100
Aircraft - Electrical Connectors - Tests Second Edition
ISO
2103
Loads Due to Use and Occupancy in Residential and Public Buildings First Edition; PNS 1089: 1991
Anodizing of Aluminium and Its Alloys - Determination of Mass per Unit Area (Surface Density) of Anodic Oxide Coatings -
ISO
2106
Gravimetric Method Second Edition; Amendment 1-1983
ISO
2107
Aluminium and aluminium alloys ù Wrought products ù Temper designations Third Edition
Aluminium and aluminium alloys ù Wrought products ù Temper designations Aluminium et alliages d'aluminium ù Produits corroyÚs ù
ISO
2107
DÚsignation des Útats mÚtallurgiques Third Edition
ISO
2108
Information and documentation - International Standard Book Number (ISBN) Fourth edition
ISO
2109
Continuous Mechanical Handling Equipment - Light Duty Belt Conveyors for Loose Bulk Materials First Edition
Information Technology - Data Communication - 25-Pole DTE/DCE Interface Connector and Contact Number Assignments
Amendment 1: Interface Connector and Contact Assignments for DTE/DCE Interface for Data Signalling Rates Above 20 000 Bit/s
ISO
2110
Third Edition; Amendment 1-1991
ISO
2113
Reinforcement fibres - Woven fabrics - Basis for a specification Second Edition; Corrigendum 1: 2/15/2003
Plastics - (Polyester Resins) and Paints and Varnishes (Binders) - Determination of Partial Acid Value and Total Acid Value Third
ISO
2114
Edition; Replaces ISO 3682
ISO
2115
Plastics - Polymer Dispersions - Determination of White Point Temperature and Minimum Film-Forming Temperature Third Edition
ISO
2120
Liquid Chlorine for Industrial Use - Determination of the Content of Chlorine by Volume in the Vaporized Product First Edition
ISO
2121
Liquid Chlorine for Industrial Use - Determination of Water Content - Gravimetric Method First Edition
Sodium and Potassium Silicates for Industrial Use - Preparation of Solution of Products Not Easily Soluble in Boiling Water and
ISO
2122
Determination of Matter Insoluble in Water First Edition
Anodizing of Aluminium and Its Alloys - Determination of Thickness of Anodic Oxide Coatings - Non-Destructive Measurement by
ISO
2128
Split-Beam Microscope First Edition
ISO
2131
Surface Active Agents - Simplified Classification First Edition
ISO
2132
Offset Duplicators Attachment Features of Plates First Edition; Amendment 1-1975
ISO
2133
Stencils for Duplicators - Minimum Overprint and Attachment Features Second Edition
Anodizing of Aluminium and Its Alloys - Accelerated Test of Light Fastness of Coloured Anodic Oxide Coatings Using Artificial Light
ISO
2135
Second Edition
ISO
2137
Petroleum Products - Lubricating Grease and Petrolatum - Determination of Cone Penetration Second Edition
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Oscillating Conveyors and Shaking or Reciprocating Feeders
ISO
2139
with Tubular Trough First Edition
ISO
2140
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Apron Conveyors First Edition
ISO
2142
Wrought Aluminium, Magnesium and Their Alloys - Selection of Specimens and Test Pieces for Mechanical Testing First Edition
Anodizing of Aluminium and Its Alloys - Estimation of Loss of Absorptive Power of Anodic Oxide Coatings After Sealing - Dye Spot
ISO
2143
Test with Prior Acid Treatment First Edition
ISO
2144
Paper, Board and Pulps - Determination of Residue (Ash) on Ignition at 900 Degrees C Fourth Edition
ISO
2145
Documentation - Numbering of Divisions and Subdivisions in Written Documents Second Edition
ISO
2148
Continuous Handling Equipment - Nomenclature First Edition
ISO
2151
Acoustics Noise test code for compressors and vacuum pumps Engineering method (Grade 2) First Edition
ISO
2155
Aircraft - Fire-Resisting Electrical Cables - Performance Requirements First Edition
ISO
2156
Aircraft - Fire-Resisting Electrical Cables - Methods of Test First Edition
ISO
2157
Dental Rotary Instruments - Nominal Diameters and Designation Code Number Third Edition; CAN/CSA-Z349.49-94
ISO
2160
Petroleum Products - Corrosiveness to Copper - Copper Strip Test Third Edition
ISO
2162-1
Technical Product Documentation - Springs - Part 1: Simplified Representation First Edition; CEN EN 2162-1: 1996
Technical Product Documentation - Springs - Part 2: Presentation of Data for Cylindrical Helical Compression Springs First Edition;
ISO
2162-2
CEN EN ISO 2162-2: 1996
Technical Product Documentation - Springs - Part 3: Vocabulary First Edition; Corrected and Reprinted - 1996; CEN EN ISO 2162-3:
ISO
2162-3
1996
ISO
2164
Pulses - Determination of Glycosidic Hydrocyanic Acid First Edition; Erratum-1981
ISO
2165
Ware Potatoes - Guide to Storage First Edition
ISO
2166
Carrots - Guide to Storage Second Edition
ISO
2167
Round-Headed Cabbage - Guide to Cold Storage and Refrigerated Transport Second Edition
ISO
2168
Table Grapes - Guide to Cold Storage First Edition
ISO
2169
Fruits and Vegetables - Physical Conditions in Cold Stores - Definitions and Measurement Second Edition
ISO
2171
Cereals and Milled Cereal Products - Determination of Total Ash Third Edition
ISO
2172
Fruit Juice - Determination of Soluble Solids Content - Pyknometric Method First Edition
ISO
2173
Fruit and Vegetable Products - Determination of Soluble Solids Content - Refractometric Method Second Edition
ISO
2174
Surface Active Agents - Preparation of Water with Known Calcium Hardness Third Edition
ISO
2176
Petroleum Products - Lubricating Grease - Determination of Dropping Point Second Edition; Technical Corrigendum 1:06-15-2001
ISO
2177
Metallic Coatings - Measurement of Coating Thickness - Coulometric Method by Anodic Dissolution Third Edition
Non-Magnetic Coatings on Magnetic Substrates - Measurement of Coating Thickness - Magnetic Method Second Edition; CEN EN
ISO
2178
ISO 2178: 1995; PNS 678: 1990
ISO
2179
Electroplated Coatings of Tin-Nickel Alloy - Specification and Test Methods Second Edition
Fluid flow in closed conduits ù Connections for pressure signal transmissions between primary and secondary elements Second
ISO
2186
Edition
ISO
2187
Spinning Preparatory Machinery, Spinning and Doubling (Twisting) Machinery - List of Equivalent Terms Second Edition
ISO
2189
Expanded Pure Agglomerated Cork - Determination of Bulk Density Second Edition
ISO
2190
Granulated Cork - Determination of Moisture Content Third Edition
ISO
2191
Cork - Expanded Pure Agglomerated - Deformation under Constant Pressure First Edition
Industrial Screens - Woven Wire Cloth, Perforated Plate and Electroformed Sheet - Designation and Nominal Sizes of Openings
ISO
2194
Second Edition
ISO
2197
Sodium Hydrogen Carbonate for Industrial Use - List of Methods of Test and Preparation of the Test Sample First Edition
Sodium Hydrogen Carbonate for Industrial Use - Determination of Sodium Hydrogen Carbonate Content - Titrimetric Method First
ISO
2199
Edition
ISO
2203
Technical Drawings - Conventional Representation of Gears First Edition
ISO
2205
Textile Machinery and Accessories - Drafting Arrangements for Spinning Machines - Terminology First Edition
ISO
2206
Packaging - Complete, Filled Transport Packages - Identification of Parts When Testing Second Edition; CEN EN 22206: 1992
ISO
2207
Petroleum Waxes - Determination of Congealing Point First Edition
ISO
2209
Liquid Halogenated Hydrocarbons for Industrial Use - Sampling First Edition
ISO
2211
Liquid Chemical Products - Measurement of Colour in Hazen Units (Platinum-Cobalt Scale) First Edition
ISO
2219
Expanded Pure Agglomerated Cork for Thermal Insulation - Characteristics, Sampling and Packaging Second Edition
ISO
2227
Formaldehyde Solutions for Industrial Use - Determination of Formaldehyde Content First Edition
ISO
2230
Rubber Products - Guidelines for Storage Second Edition
ISO
2231
Rubber- or Plastics-Coated Fabrics - Standard Atmospheres for Conditioning and Testing Second Edition; CEN EN ISO 2231: 1995
Round Drawn Wire for General Purpose Non-Alloy Steel Wire Ropes and for Large Diameter Steel Wire Ropes - Specifications
ISO
2232
Second Edition
ISO
2233
Packaging - Complete, Filled Transport Packages and Unit Loads - Conditioning for Testing Fourth Edition
ISO
2234
Packaging - Complete, Filled Transport Packages and Unit Loads - Stacking Tests Using a Static Load Third Edition
ISO
2236
Assembly Tools for Screws and Nuts - Forged and Tubular Socket Wrenches - Maximum Outside Head Dimensions Third Edition
ISO
2238
Machine Bridge Reamers First Edition
ISO
2240
Photography Colour reversal camera films Determination of ISO speed Fourth Edition
ISO
2244
Packaging - Complete, Filled Transport Packages and Unit Loads - Horizontal Impact Tests Third Edition
ISO
2245
Shaped insulating refractory products Classification Third Edition
ISO
2247
Packaging - Complete, Filled Transport Packages and Unit Loads - Vibration Tests at Fixed Low Frequency Third Edition
ISO
2248
Packaging - Complete, Filled Transport Packages - Vertical Impact Test by Dropping Second Edition; CEN EN 22248: 1992
ISO
2250
Finishing Reamers for Morse and Metric Tapers, with Parallel Shanks and Morse Taper Shanks First Edition
ISO
2253
Curry Powder - Specification Third Edition
ISO
2254
Cloves, whole and ground (powdered) Specification Second Edition
ISO
2255
Coriander, (Coriandrum Sativum L.), Whole or Ground (Powdered) - Specification Second Edition
ISO
2256
Dried Mint (Spearmint) (Mentha spicata Linnaeus Syn. Mentha viridis Linnaeus) - Specification First Edition
Office Machines and Printing Machines Used for Information Processing - Widths of Fabric Printing Ribbons on Spools Second
ISO
2257
Edition; Corrected and Reprinted - 1981
ISO
2258
Printing Ribbons - Minimum Markings to Appear on Containers Second Edition
ISO
2261
Reciprocating Internal Combustion Engines - Hand-Operated Control Devices - Standard Direction of Motion Second Edition
ISO
2262
General Purpose Thimbles for Use with Steel Wire Ropes - Specification Second Edition
Surface Active Agents - Evaluation of Certain Effects of Laundering - Methods of Preparation and Use of Unsoiled Cotton Control
ISO
2267
Cloth Third Edition
Surface Active Agents (Non-Ionic) - Determination of Polyethylene Glycols and Non-Ionic Active Matter (Adducts) - Weibull Method
ISO
2268
First Edition
ISO
2269
Shipbuilding - Class A Magnetic Compasses, Azimuth Reading Devices and Binnacles - Tests and Certification Second Edition
ISO
2270
Non-Ionic Surface Active Agents - Polyethoxylated Derivatives - Iodometric Determination of Oxyethylene Groups Second Edition
Surface Active Agents - Detergents - Determination of Anionic-Active Matter by Manual or Mechanical Direct Two-Phase Titration
ISO
2271
Procedure Second Edition
Surface Active Agents - Soaps - Determination of Low Contents of Free Glycerol by Molecular Absorption Spectrometry Second
ISO
2272
Edition
ISO
2277
Static Invertors for Aircraft First Edition; Erratum-1973
ISO
2281
Horology - Water-Resistant Watches Third Edition
ISO
2283
Long Shank Machine Taps with Nominal Diameters from M3 to M24 and 1/8 to 1 in - Reduced Shank Taps Second Edition
ISO
2284
Hand Taps for Parallel and Taper Pipe Threads - General Dimensions and Marking Third Edition
Rubber, vulcanized or thermoplastic ù Determination of tension set under constant elongation, and of tension set, elongation and
ISO
2285
creep under constant tensile load Sixth Edition
Rubber- or Plastics-Coated Fabrics - Determination of Roll Characteristics - Part 1: Methods for Determination of Length, Width and
ISO
2286-1
Net Mass First Edition
Rubber- or Plastics-Coated Fabrics - Determination of Roll Characteristics - Part 2: Methods for Determination of Total Mass per Unit
ISO
2286-2
Area, Mass per Unit Area of Coating and Mass per Unit Area of Substrate First Edition
Rubber- or Plastics-Coated Fabrics - Determination of Roll Characteristics - Part 3: Methods for Determination of Thickness First
ISO
2286-3
Edition
ISO
2291
Cocoa Beans - Determination of Moisture Content (Routine Method) Second Edition
ISO
2292
Cocoa Beans - Sampling First Edition
ISO
2294
Meat and Meat Products - Determination of Total Phosphorus Content (Reference Method) First Edition
ISO
2295
Avocados - Guide for Storage and Transport First Edition
ISO
2296
Metal Slitting Saws with Fine and Coarse Teeth - Metric Series First Edition
ISO
2297
Chemical Analysis of Aluminium and Its Alloys - Complexometric Determination of Magnesium First Edition
ISO
2299
Sawn Timber of Broadleaved Species - Defects - Classification First Edition
ISO
2300
Sawn Timber of Broadleaved Species - Defects - Terms and Definitions First Edition
ISO
2301
Sawn Timber of Broadleaved Species - Defects - Measurement First Edition
ISO
2302
Isobutene-isoprene rubber (IIR) Evaluation procedures Fifth Edition
ISO
2303
Isoprene Rubber (IR) - Non-Oil-Extended, Solution-Polymerized Types - Evaluation Procedure Fourth Edition
ISO
2306
Drills for Use Prior to Tapping Screw Threads First Edition
ISO
2307
Fibre ropes Determination of certain physical and mechanical properties Third edition
ISO
2308
Hooks for Lifting Freight Containers of up to 30 Tonnes Capacity - Basic Requirements First Edition
ISO
2309
Coke - Sampling Second Edition
Textile Fabrics - Determination of the Recovery from Creasing of a Horizontally Folded Specimen by Measuring the Angle of
ISO
2313
Recovery First Edition
ISO
2314
Gas Turbines - Acceptance Tests Second Edition; Corrigendum 1-1997; Amendment 1-1997
ISO
2315
Aircraft - Two- and Four-Pole Sealed Electromagnetic Relays, 2 A and 3 A - Clearance and Fixing Dimensions Second Edition
Prevailing Torque Type Steel Hexagon Nuts - Mechanical and Performance Properties Third Edition; Technical Corrigendum 1:
ISO
2320
09/01/2006
ISO
2321
Rubber threads Methods of test Third Edition
ISO
2322
Styrene-Butadiene Rubber (SBR) - Emulsion- and Solution-Polymerized Types - Evaluation Procedures Fourth Edition
ISO
2325
Coke - Size Analysis (Nominal Top Size 20 mm or Less) Third Edition
ISO
2326
Continuous Mechanical Handling Equipment for Loose Bulk Materials - Aeroslides First Edition
ISO
2327
Pneumatic Handling Appliances for Loose Bulk Materials - Piping First Edition
ISO
2328
Fork-Lift Trucks - Hook-On Type Fork Arms and Fork Arm Carriages - Mounting Dimensions Third Edition
ISO
2330
Fork-Lift Trucks - Fork Arms - Technical Characteristics and Testing Third Edition
ISO
2331
Fork Lift Trucks - Hook-On Type Fork Arms - Vocabulary First Edition
Agricultural Tractors and Machinery - Connection of Implements Via Three-Point Linkage - Clearance Zone Around Implement
ISO
2332
Second Edition
ISO
2336-1
Hacksaw Blades - Part 1: Dimensions for Hand Blades First Edition; Replaces ISO 2336
Hacksaw blades Part 2: Dimensions for machine blades Lames de scies droites Ó mÚtaux Partie 2: Dimensions des lames Ó
ISO
2336-2
machine Second Edition
ISO
2338
Parallel Pins, of Unhardened Steel and Austenitic Stainless Steel Second Edition
ISO
2339
Taper Pins, Unhardened Second Edition
ISO
2340
Clevis Pins without Head Second Edition
ISO
2341
Clevis Pins with Head Second Edition
ISO
2342
Slotted headless screws with shank Second Edition
ISO
2344
Road Vehicles - M14 X 1,25 Spark-Plugs with Conical Seating and Their Cylinder Head Housings Seventh Edition
ISO
2345
Road Vehicles - M18 X 1,5 Spark-Plugs with Conical Seating and Their Cylinder Head Housing Fifth Edition
Road Vehicles - M14 x 1,25 Compact Spark-Plugs with Flat Seating and 19mm Hexagon and Their Cylinder Head Housing Fifth
ISO
2346
Edition
ISO
2347
Road Vehicles - M14 X 1,25 Compact Spark-Plugs with Conical Seating and Their Cylinder Head Housing Fifth Edition
Assembly tools for screws and nuts ù Machine-operated screwdriver bits ù Part 1: Screwdriver bits for slotted head screws Second
ISO
2351-1
Edition
Assembly Tools for Screws and Nuts - Machine-Operated Screwdriver Bits - Part 2: Screwdriver Bits for Cross-Recessed Head
ISO
2351-2
Screws First Edition
Assembly Tools for Screws and Nuts - Machine-Operated Screwdriver Bits - Part 3: Screwdriver Bits for Hexagon Socket Screws
ISO
2351-3
First Edition; Replaces ISO 3109
Magnesium and Its Alloys - Determination of Manganese in Magnesium Alloys Containing Zirconium, Rare Earths, Thorium and
ISO
2353
Silver - Periodate Photometric Method First Edition
ISO
2354
Magnesium Alloys - Determination of Insoluble Zirconium - Alizarin Sulphonate Photometric Method Second Edition
ISO
2355
Chemical Analysis of Magnesium and Its Alloys - Determination of Rare Earths - Gravimetric Method First Edition
Non-conductive coatings on non-magnetic electrically conductive basis materials Measurement of coating thickness Amplitude-
ISO
2360
sensitive eddy current method Third Edition
Electrodeposited Nickel Coatings on Magnetic and Non-Magnetic Substrates - Measurement of Coating Thickness - Magnetic
ISO
2361
Method Second Edition; PNS 671: 1990
Cryolite, Natural and Artificial - Determination of Sodium Content - Flame Emission and Atomic Absorption Spectrophotometric
ISO
2366
Methods First Edition
ISO
2367
Cryolite (Natural and Artificial) - Determination of Aluminium Content - 8-Hydroxyquinoline Gravimetric Method First Edition
ISO
2370
Textiles - Determination of Fineness of Flax Fibres - Permeametric Methods Second Edition
ISO
2374
Lifting Appliances - Range of Maximum Capacities for Basic Models First Edition
ISO
2375
Information Technology - Procedure for Registration of Escape Sequences and Coded Character Sets First Edition
ISO
2376
Anodization (Anodic Oxidation) of Aluminium and Its Alloys - Insulation Check by Measurement of Breakdown Potential First Edition
ISO
2377
Magnesium Alloy Sand Castings - Reference Test Bar First Edition
ISO
2378
Aluminium Alloy Chill Castings - Reference Test Bar First Edition
ISO
2379
Aluminium Alloy Sand Castings - Reference Test Bar First Edition
Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 1: Tips for hand- and machine-operated screwdrivers
ISO
2380-1
Third Edition
Assembly tools for screws and nuts Screwdrivers for slotted-head screws Part 2: General requirements, lengths of blades and
ISO
2380-2
marking of hand-operated screwdrivers Third Edition
ISO
2382-1
Information Technology - Vocabulary - Part 1: Fundamental Terms Third Edition
ISO
2382-3
Information Processing Systems - Vocabulary - Part 03: Equipment Technology Second Edition
Information Technology - Vocabulary - Part 4: Organization of Data Technologies De L'Information - Vocabulaire - Partie 4:
ISO
2382-4
Organisation Des Donnees First Edition
Information Technology - Vocabulary - Part 5: Representation of Data Technologies De L'Information - Vocabulaire - Partie 5:
ISO
2382-5
Representation Des Donnees First Edition
ISO
2382-6
Information Processing Systems - Vocabulary - Part 06: Preparation and Handling of Data Second Edition
Information Technology - Vocabulary - Part 07: Computer Programming Technologies De L'Information - Vocabulaire - Partie 7:
ISO
2382-7
Programmation Des Ordinateurs Third Edition
Information Technology - Vocabulary - Part 8: Security Technologies DeL'Information - Vocabularie - Partie 8: Securite Second
ISO
2382-8
Edition
ISO
2382-9
Information Technology - Vocabulary - Part 9: Data Communication Second Edition
ISO
2382-12
Information Processing Systems - Vocabulary - Part 12: Peripheral Equipment Second Edition
ISO
2382-13
Information Technology - Vocabulary - Part 13: Computer Graphics Second Edition
ISO
2382-15
Information Technology - Vocabulary - Part 15: Programming Languages First Edition
ISO
2382-16
Information Technology - Vocabulary - Part 16: Information Theory Second Edition
Information Technology - Vocabulary - Part 17: Databases Technologies De I'Information - Vocabulaire - Partie 17: Bases De
ISO
2382-17
Donnees Second Edition
Information Technology - Vocabulary - Part 18: Distributed Data Processing Technologies De L'Information - Vocabulaire - Partie 18:
ISO
2382-18
Informatique Repartie First Edition
ISO
2382-19
Information Processing Systems - Vocabulary - Part 19: Analog Computing Second Edition
ISO
2382-20
Information Technology - Vocabulary - Part 20: System Development First Edition
ISO
2382-21
Data Processing - Vocabulary - Part 21: Interfaces between Process Computer Systems and Technical Processes First Edition
ISO
2382-22
Information Processing Systems - Vocabulary - Part 22: Calculators First Edition
ISO
2382-23
Information Technology - Vocabulary - Part 23: Text Processing First Edition
ISO
2382-24
Information Technology - Vocabulary - Part 24: Computer-Integrated Manufacturing First Edition
ISO
2382-25
Information Technology - Vocabulary - Part 25: Local Area Networks First Edition
ISO
2382-26
Information Technology - Vocabulary - Part 26: Open Systems Interconnection First Edition
ISO
2382-27
Information Technology - Vocabulary - Part 27: Office Automation First Edition
ISO
2382-28
Information Technology - Vocabulary - Part 28: Artificial Intelligence - Basic Concepts and Expert Systems First Edition
Information Technology - Vocabulary - Part 29: Artificial Intelligence - Speech Recognition and Synthesis Technologies De
ISO
2382-29
L'Information - Vocabulaire - Partie 29: Intelligence Artificielle - Reconnaissance Et Synthese De La Parole First Edition
ISO
2382-31
Information Technology - Vocabulary - Part 31: Artificial Intelligence - Machine Learning First Edition
Information technology Vocabulary Part 32: Electronic Mail Technologies de l'information Vocabulaire Partie 32: Courrier
ISO
2382-32
Úlectronique First Edition
Information Technology - Vocabulary - Part 34: Artificial Intelligence - Neural Networks Technologies De L'Information - Vocabulaire -
ISO
2382-34
Partie 34: Intelligence Artificielle - Reseaux Neuronaux First Edition
Data Processing - Vocabulary - Section 02: Arithmetic and Logic Operations Traitement De L'Information - Vocabulaire - Chapitre 02:
ISO
2382-2
Operations Arithmetiques Et Logiques First Edition
Data Processing - Vocabulary - Section 10: Operating Techniques and Facilities Traitement De L'Information - Vocabulaire - Chapitre
ISO
2382-10
10: Techniques Et Moyens D'Exploitation First Edition
Information Technology - Vocabulary - Part 14: Reliability, Maintainability and Availability Technologies De L'Information - Vocabulaire
ISO
2382-14
- Partie 14: Fiabilite, Maintenabilite Et Disponibilite Second Edition
ISO
2384
Documentation - Presentation of Translations First Edition
Corkwood in Planks, Virgin Cork, Cleanings, Cork Pieces, Corkwood Refuse and Corkwaste - Sampling to Determine Moisture
ISO
2385
Content Second Edition
Corkwood in Planks, Virgin Cork, Ramassage, Gleanings, Corkwood Refuse and Corkwaste - Determination of Moisture Content
ISO
2386
Third Edition
ISO
2393
Rubber Test Mixes - Preparation, Mixing and Vulcanization - Equipment and Procedures Second Edition
ISO
2394
General Principles on Reliability for Structures Third Edition
ISO
2395
Test Sieves and Test Sieving - Vocabulary Second Edition
ISO
2398
Rubber hoses, textile-reinforced, for compressed air Specification Fifth Edition
ISO
2400
Welds in Steel - Reference Block for the Calibration of Equipment for Ultrasonic Examination First Edition
ISO
2401
Covered Electrodes - Determination of the Efficiency, Metal Recovery and Deposition Coefficient First Edition; CEN EN 22401: 1994
ISO
2402
Shell Reamers with Taper Bore (Taper Bore 1 : 30 (Included)) with Slot Drive and Arbors for Shell Reamers First Edition
ISO
2403
Textiles - Cotton Fibres - Determination of Micronaire Value First Edition
ISO
2404
Cinematography - Six-Track Magnetic Sound Records on 70 mm Striped Release Prints - Locations and Dimensions Second Edition
ISO
2406
Continuous Mechanical Handling Equipment - Mobile and Portable Conveyors - Constructional Specifications First Edition
ISO
2407
Tests Conditions for Internal Cylindrical Grinding Machines with Horizontal Spindle - Testing of Accuracy Third Edition
ISO
2408
Steel wire ropes for general purposes Minimum requirements Third Edition
ISO
2409
Paints and Varnishes - Cross-Cut Test Third Edition
ISO
2410
Household Refrigerators - Methods of Test for the Information of the Consumer First Edition
ISO
2411
Rubber- or Plastics-Coated Fabrics - Determination of Coating Adhesion Third Edition
ISO
2412
Shipbuilding - Colours of Indicator Lights Second Edition
ISO
2415
Forged shackles for general lifting purposes Dee shackles and bow shackles Third Edition
ISO
2416
Passenger Cars - Mass Distribution Third Edition
ISO
2417
Leather Physical and mechanical tests Determination of the static absorption of water Second Edition; IULTCS/IUP 7
ISO
2418
Leather Chemical, physical and mechanical and fastness tests Sampling location Second Edition; IULTCS/IUP 2 and IUC 2
ISO
2419
Leather Physical and mechanical tests Sample preparation and conditioning Third Edition; IULTCS/IUP 1 and IUP 3
ISO
2420
Leather Physical and mechanical tests Determination of apparent density Second Edition; IULTCS/IUP 5
ISO
2421
Coated Abrasives - Cylindrical Sleeves Second Edition
ISO
2423
Acceptance Conditions for Radial Drilling Machines with the Arm Adjustable in Height - Testing of Accuracy Second Edition
ISO
2424
Textile floor coverings ù Vocabulary RevÛtements de sol textiles ù Vocabulaire Fourth Edition
ISO
2425
Measurement of Liquid Flow in Open Channels Under Tidal Conditions Second Edition; AMENDMENT 1: 12/01/2003
ISO
2426-1
Plywood - Classification by Surface Appearance - Part 1: General First Edition; Supersedes ISO 2426: 1974
ISO
2426-2
Plywood - Classification by Surface Appearance - Part 2: Hardwood First Edition
ISO
2426-3
Plywood - Classification by Surface Appearance - Part 3: Softwood First Edition; Supersedes ISO 2426: 1974
Paints and Varnishes - Determination of Flow Time by Use of Flow Cups Fourth Edition; Technical Corrigendum 1: 06-15-1994;
ISO
2431
Technical Corrigendum 2: 04-01-1999
Machine Tools - Test Conditions for External Cylindrical and Universal Grinding Machines with a Movable Table - Testing of the
ISO
2433
Accuracy Third Edition
ISO
2434
Compressed Non-Breathing Air for Use in Aircraft First Edition
ISO
2435
Nitrogen for Use in Aircraft First Edition
ISO
2436
Heat-Resisting Equipment Wires for Aircraft - Methods of Test First Edition
Flexible Cellular Polymeric Materials - Determination of Hardness (Indentation Technique) Third Edition; Technical Corrigendum 1-
ISO
2439
1998
ISO
2440
Flexible and Rigid Cellular Polymeric Materials - Accelerated Ageing Tests Third Edition
ISO
2444
Joints in Building - Vocabulary Second Edition
ISO
2445
Joints in Building - Fundamental Principles for Design First Edition
ISO
2446
Milk - Determination of Fat Content (Routine Method) First Edition
ISO
2447
Fruit and Vegetable Products - Determination of Tin Content Second Edition
ISO
2448
Fruit and Vegetable Products - Determination of Ethanol Content Second Edition
Milk and Liquid Milk Products - Density Hydrometers for Use in Products with a Surface Tension of Approximately 45 mN/m First
ISO
2449
Edition
ISO
2450
Cream - Determination of Fat Content - Gravimetric Method (Reference Method) Third Edition
ISO
2451
Cocoa Beans - Specification First Edition
Rubber, Raw Styrene-Butadiene, Emulsion-Polymerized - Determination of Bound Styrene Content - Refractive Index Method
ISO
2453
Second Edition; Corrigendum 1:08/15/2003
ISO
2454
Rubber Products - Determination of Zinc Content - EDTA Titrimetric Method Third Edition
ISO
2456
Surface Active Agents - Water Used as a Solvent for Tests - Specification and Test Methods First Edition
ISO
2457
Solid Wood Parquet - Classification of Beech Strips Second Edition
ISO
2460
Sodium Hydrogen Carbonate for Industrial Use - Determination of Iron Content - 1,10-Penanthroline Photometric Method First Edition
ISO
2461
Sodium Chlorate for Industrial Use - Determination of Matter Insoluble in Water First Edition
ISO
2462
Sodium Chlorate for Industrial Use - Determination of Moisture Content - Gravimetric Method First Edition
ISO
2463
Sodium Chlorate for Industrial Use - Determination of Chloride Content - Mercurimetric Method First Edition
Potassium Hydroxide for Industrial Use - Sampling - Test Sample - Preparation of the Main Solution for Carrying out Certain
ISO
2466
Determinations First Edition
Cinematography Image area produced by 65 mm/5 perforation motion-picture camera aperture and maximum projectable image
ISO
2467
area on 70 mm/5 perforation motion-picture prints Positions and dimensions Third Edition
ISO
2469
Paper, board and pulps ù Measurement of diffuse radiance factor Fourth Edition
ISO
2470
Paper, Board and Pulps - Measurement of Diffuse Blue Reflectance Factor (ISO Brightness) Third Editon
ISO
2471
Paper and Board - Determination of Opacity (Paper Backing) - Diffuse Reflectance Method Third Edition
Chloroprene rubber (CR) - Generalpurpose types - Evaluation procedure Fourth Edition; Technical Corrigendum 1: 06/01/2001;
ISO
2475
Amendment 1: 10/15/2005
ISO
2476
Rubber, Butadiene (BR) - Solution-Polymerized Types - Evaluation Procedures Fourth Edition
ISO
2477
Shaped insulating refractory products - Determination of permanent change in dimensions on heating Third Edition
ISO
2478
Dense Shaped Refractory Products - Determination of Permanent Change in Dimensions on Heating Second Edition
Sodium Chloride for Industrial Use - Determination of Matter Insoluble in Water or in Acid and Preparation of Principal Solutions for
ISO
2479
Other Determinations First Edition
ISO
2480
Sodium Chloride for Industrial Use - Determination of Sulphate Content - Barium Sulphate Gravimetric Method First Edition
ISO
2481
Sodium Chloride for Industrial Use - Determination of Halogens, Expressed as Chlorine - Mercurimetric Method First Edition
Sodium Chloride for Industrial Use - Determination of Calcium and Magnesium Contents - EDTA Complexometric Methods First
ISO
2482
Edition
ISO
2483
Sodium Chloride for Industrial Use - Determination of the Loss of Mass at 110 Degrees Celsius First Edition
ISO
2490
Solid (monobloc) gear hobs with tenon drive or axial keyway, 0,5 to 40 module ù Nominal dimensions Third Edition
ISO
2491
Thin Parallel Keys and Their Corresponding Keyways (Dimensions in Millimetres) First Edition
ISO
2492
Thin Taper Keys with or without Gib Head and Their Corresponding Keyways (Dimensions in Millimetres) First Edition
ISO
2493
Paper and Board - Determination of Resistance to Bending Second Edition
ISO
2495
Iron Blue Pigments - Specifications and Methods of Test Second Edition
Gas Welding Equipment - Pressure Regulators for Gas Cylinders Used in Welding, Cutting and Allied Processes up to 300 bar Third
ISO
2503
Edition
Radiography of Welds and Viewing Conditions for Films - Utilization of Recommended Patterns of Image Quality Indicators (I.Q.I.)
ISO
2504
First Edition
ISO
2505
Thermoplastics pipes - Longitudinal reversion - Test method and parameters Second edition; Replaces ISO 2505-1 and 2505-2
ISO
2507-1
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 1: General Test Method First Edition; Replaces ISO 2507
Thermoplastics Pipes and Fittings - Vicat Softening Temperature - Part 2: Test Conditions for Unplasticized Poly(Vinyl Chloride) (PVC-
U) or Chlorinated Poly(Vinyl Chloride) (PVC-C) Pipes and Fittings and for High Impact Resistance Poly(Vinyl Chloride) (PVC-HI)
ISO
2507-2
Pipes First Edition; Replaces ISO 2507
////////////////////////////////////////// |
||
|
|
|