Hyundai Veloster (2019 year). Manual - part 26
Engine compartment fuse panel
Fuse Name
Fuse Rating
Protected Component
FUEL PUMP
20A
E/R Junction Block (Fuel Pump Relay)
VACUUM
20A
Vacuum Pump
PUMP1
TCU1
15A
TCM
COOLING
40A
E/R Junction Block (C/Fan1 Low Relay, C/Fan2 Hi Relay) (G4NH)
FAN2
B+1
40A
IGPM ((Fuse - BRAKE SWITCH, PDM1, PDM3, MODULE1, DOOR LOCK), Leak Current Autocut Device)
DCT1
40A
TCM
DCT2
40A
TCM
B/ALARM
15A
E/R Junction Block (B/ALARM Horn Relay)
HORN
7
ABS1
40A
ESC Module, ABS Control Module, Multipurpose Check Connector
ABS2
30A
ESC Module, ABS Control Module
[G4FJ] : 1.6 T-GDI
[G4NH] : 2.0 MPI
7-63
Maintenance
Engine compartment fuse panel
Fuse Name
Fuse Rating
Protected Component
G4FJ : Canister Close Valve, Oil Control Valve #1/#2, RCV Control Solenoid Valve,
Purge Control Solenoid Valve, E/R Junction Block (C/FAN2 HI Relay)
SENSOR2
10A
G4NH : Canister Close Valve, Oil Control Valve #1/#2/#3, Electronic Thermostat, Variable Intake Solenoid
Valve, Purge Control Solenoid Valve, E/R Junction Block (C/FAN 1 Low Relay, C/FAN 2 HI Relay)
ECU2
10A
ECM (G4FJ)
ECU1
20A
ECM/PCM
INJECTOR
15A
Injector #1/#2/#3/#4 (G4NH)
SENSOR1
15A
Oxygen Sensor (Up/Down)
IGN COIL
20A
Ignition Coil #1/#2/#3/#4
ECU3
15A
ECM/PCM
A/C
10A
A/CON COMP Relay (G4NH)
ECU5
10A
ECM/PCM
VACUUM
15A
Vacuum Pump (G4FJ)
PUMP2
[G4FJ] : 1.6 T-GDI
[G4NH] : 2.0 MPI
7-64
Engine compartment fuse panel
Fuse Name
Fuse Rating
Protected Component
ABS3
10A
ABS Control Module, ESC Module, Multipurpose Check Connector
TCU2
15A
Transmission Range Switch(A/T), TCM (With DCT)
SENSOR3
10A
E/R Junction Block (F/PUMP Relay)
ECU4
15A
ECM/PCM
HORN
15A
Horn Relay
[G4FJ] : 1.6 T-GDI
[G4NH] : 2.0 MPI
7
7-65
Maintenance
Engine compartment fuse panel
(Battery terminal cover)
(for Nu 2.0 MPI)
OJS078055L
Inside the fuse/relay box cover, you
can find the fuse/relay label describ-
ing fuse/relay names and ratings.
i
Information
OPD076065
Not all fuse panel descriptions in this
manual may be applicable to your
NOTICE
vehicle; the information is accurate at
the time of printing. When you inspect
After checking the fuse panel in the engine compartment, securely
the fuse panel in your vehicle, refer to
install the cover. If it is not securely latched, electrical failure may occur
the fuse panel label.
from water contact.
7-66
LIGHT BULBS
Consult an authorized HYUNDAI
i
Information - Desiccant
WARNING
dealer to replace most vehicle light
(if equipped)
bulbs. It is difficult to replace vehicle
This vehicle is equipped with desic-
•
Prior to replacing a lamp,
light bulbs because other parts of the
vehicle must be removed before you
cant to reduce fogging inside the head-
depress the foot brake, move
lamp due to moisture.
the shift lever into P
(Park)
can get to the bulb. This is especially
true for removing the headlamp
The desiccant is consumable and its
apply the parking brake, place
the ignition switch to the
assembly to get to the bulb(s).
performance may change based on the
LOCK/OFF position, and take
Removing/installing the headlamp
used period or environment.
the key with you when leaving
assembly can result in damage to
If fogging inside the headlamp due to
the vehicle to avoid sudden
the vehicle.
moisture continues for a long time,
movement of the vehicle and
have your vehicle checked by an
to prevent possible electric
authorized HYUNDAI dealer.
i
Information
shock.
After heavy driving, rain or washing,
•
Be aware the bulbs may be
headlamp and trunk lenses could
hot and may burn your fin-
appear frosty. This condition is caused
gers.
by the temperature difference
between the lamp inside and the out-
side temperature. This is similar to the
condensation on your windows inside
7
your vehicle during the rain and does-
n’t indicate a problem with your vehi-
cle. If the water leaks into the lamp
bulb circuitry, have your vehicle
checked by an authorized HYUNDAI
dealer.
7-67
Maintenance
Headlamp, Position lamp,
•
Always handle them carefully, and
WARNING
Daytime Running Light, Turn
avoid scratches and abrasions. If
signal lamp and Side marker
the bulbs are lit, avoid contact with
liquids.
Type A
•
Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
•
A bulb should be operated only
when installed in a headlamp.
•
If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
OLMB073042L
•
Handle halogen bulbs with
care. Halogen bulbs contain
pressurized gas that will pro-
OJS078057N
duce flying pieces of glass that
(1) Headlamp (High)
could cause injuries if broken.
(2) Headlamp (Low)
•
Wear eye protection when
changing a bulb. Allow the
(3) Turn signal lamp
bulb to cool down before han-
(4) Position lamp &
dling it.
Daytime running light (DRL)
(5) Side marker
7-68
■ High/Low beam
5. Remove the bulb from the head-
lamp assembly.
6. Install a new headlamp bulb and
snap the headlamp bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlamp bulb sock-
et-connector.
8. Install the headlamp bulb cover by
turning it clockwise.
OJS078027
OJS078028
[1] : High beam, [2] : Low beam
i
Information
Turn signal
Headlamp
The headlamp aiming should be
1. Open the hood.
adjusted after an accident or after the
1. Open the hood.
2. Disconnect the negative battery
headlamp assembly is reinstalled at an
2. Disconnect the negative battery
cable.
authorized HYUNDAI dealer.
cable.
3. Remove the socket (1) from the
3. Remove the headlamp bulb cover
assembly by turning the socket
by turning it counterclockwise.
counterclockwise until the tabs on
the socket align with the slots on
7
4. Disconnect the headlamp bulb
the assembly.
socket-connector.
4. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7-69
Maintenance
5. Install a new bulb by inserting it
Type B
into the socket and rotating it until
it locks into place.
6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
7. Push the socket into the assembly
and turn the socket clockwise.
Position lamp and daytime running
light
OJS078070N
Your vehicle is equipped with LED
Side marker lamp
OJS078058N
lamps. LED lamps do not have
1. Open the hood.
replaceable bulbs. If the LED lamp
(1) Headlamp (High)
does not operate, have the vehicle
2. Disconnect the negative battery
(2) Headlamp (Low)
checked by an authorized HYUNDAI
cable.
(3) Turn signal lamp
dealer.
3. Remove the socket from the
(4) Position lamp &
assembly by turning the socket
Daytime running light (DRL)
counterclockwise until the tabs on
the socket align with the slots on
(5) Side marker
the assembly.
4. Remove the bulb from the socket
by pulling out the bulb.
5. Insert a new bulb.
7-70
• Always handle them carefully, and
WARNING
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids.
• Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit.
• A bulb should be operated only
when installed in a headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
OJS078029
and carefully dispose of it.
OLMB073042L
Headlamp (High beam)
•
Handle halogen bulbs with
1. Open the hood.
Headlamp (Low beam), side mark-
care. Halogen bulbs contain
er, position lamp and daytime run-
2. Disconnect the negative battery
pressurized gas that will pro-
ning light
cable.
duce flying pieces of glass that
Your vehicle is equipped with LED
3. Remove the headlamp bulb cover
could cause injuries if broken.
lamps. LED lamps do not have
by turning it counterclockwise.
•
Wear eye protection when
replaceable bulbs. If the LED lamp
4. Disconnect the headlamp bulb
changing a bulb. Allow the
does not operate, have the vehicle
socket-connector.
7
bulb to cool down before han-
checked by an authorized HYUNDAI
dling it.
5. Remove the bulb from the head-
dealer.
lamp assembly.
6. Install a new headlamp bulb and
snap the headlamp bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlamp bulb sock-
et-connector.
7-71
Maintenance
8. Install the headlamp bulb cover by
3. Remove the socket from the
Side Repeater Lamp
turning it clockwise.
assembly by turning the socket
Replacement
counterclockwise until the tabs on
the socket align with the slots on
i
Information
the assembly.
The headlamp aiming should be
4. Remove the bulb from the socket
adjusted after an accident or after the
by pressing it in and rotating it
headlamp assembly is reinstalled at an
counterclockwise until the tabs on
authorized HYUNDAI dealer.
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Install a new bulb by inserting it
into the socket and rotating it until
it locks into place.
OJS078030
6. Install the socket in the assembly
If the light bulb does not operate,
by aligning the tabs on the socket
have the vehicle checked by an
with the slots in the assembly.
authorized HYUNDAI dealer.
7. Push the socket into the assembly
and turn the socket clockwise.
OJS078059L
Turn signal
1. Open the hood.
2. Disconnect the negative battery
cable.
7-72
Rear Combination Light Bulb
Replacement
OJS078032
OJS078033
Stop/Tail lamp and turn signal lamp
4. Remove the rear combination
lamp assembly from the body of
OJS078031N
1. Open the liftgate.
the vehicle.
2. Open the lamp assembly retaining
(1) Stop/Tail lamp
5. Remove the socket from the
screw covers.
(2) Tail lamp or Stop/Tail lamp
assembly by turning the socket
3. Loosen the lamp assembly retain-
(3) Turn signal lamp
counterclockwise until the tabs on
ing screws with a cross-tip screw-
the socket align with the slots on
(4) Backup lamp
driver.
the assembly.
(5) Side marker
7
Side marker and Stop/Tail lamp
light
Your vehicle is equipped with LED
lamps. LED lamps do not have
replaceable bulbs. If the LED lamp
does not operate, have the vehicle
checked by an authorized HYUNDAI
dealer.
7-73
Maintenance
■ Type A
7. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
8. Install the socket into the assem-
bly by aligning the tabs on the
socket with the slots in the assem-
bly. Push the socket into the
assembly and turn the socket
clockwise.
9. Reinstall the lamp assembly to the
body of the vehicle.
OJS078035L
OJS078034
■ Type B
Tail lamp and backup lamp
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a
flat-blade screwdriver.
OJS078036L
[A] : Stop/Tail lamp, [B] : Turn signal lamp
6. Remove the bulb from the socket by
pressing it in and rotating it counter-
clockwise until the tabs on the bulb
align with the slots in the socket.
Pull the bulb out of the socket.
7-74
■ Type A
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
7. Install the socket into the assem-
bly by aligning the tabs on the
OJS078037L
OJS078071N
socket with the slots in the assem-
■ Type B
bly. Push the socket into the
Side marker
assembly and turn the socket
1. Turn off the engine.
clockwise.
2. Open the liftgate.
8. Reinstall the lamp assembly to the
3. Remove the service cover using a
body of the vehicle.
flat-blade screwdriver.
4. Remove the rear combination light
assembly from the body of the
vehicle.
7
5. Remove the socket from the
assembly by turning the socket
OJS078038L
counterclock wise until the tabs on
[A] : Tail lamp, [B] : Backup lamp
the socket align with the slots on
the assembly.
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7-75
Maintenance
6. Remove the bulb by pulling it out.
High Mounted Stop Lamp
License Plate Light Bulb
7. Inset a new bulb by inserting it into
Replacement
Replacement
the socket.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
OJS078039
OJS078040
If the high mounted stop lamp does
1. Using a flat-blade screwdriver,
not operate, have the vehicle
gently pry the lens cover from the
checked by an authorized HYUNDAI
lamp housing.
dealer.
2. Remove the bulb by pulling it
straight out.
3. Install a new bulb.
4. Reinstall in the reverse order.
7-76
Interior Light Bulb Replacement
Map lamp, room lamp, vanity mirror lamp and luggage compartment lamp
■ Map lamp
■ Vanity mirror lamp
1. Using a flat-head screwdriver,
gently pry the lens from the interi-
or light housing.
2. Remove the bulb by pulling it
straight out.
WARNING
Prior to working on the Interior
Lights, ensure that the "OFF"
button is depressed to avoid
OOS077053
OJS078041
burning your fingers or receiv-
■ Room lamp - without sunroof
■ Luggage compartment lamp
ing an electric shock.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior
light housing notches and snap
7
the lens into place.
NOTICE
Be careful not to damage the
cover, tab, and plastic housing.
OOS077054
OJS078042
7-77
Maintenance
APPEARANCE CARE
Exterior Care
Even prompt washing with plain
NOTICE
water may not completely remove all
Exterior general caution
these deposits. A mild soap, safe for
•
Do not use harsh soap, chemical
It is very important to follow the label
use on painted surfaces, should be
detergents or hot water, and do
directions when using any chemical
used.
not wash the vehicle in direct
cleaner or polish. Read all warning
sunlight or when the body of the
After washing, rinse the vehicle thor-
and caution statements that appear
vehicle is warm.
oughly with lukewarm or cold water.
on the label.
Do not allow soap to dry on the fin-
•
Be careful when washing the
ish.
side windows of your vehicle.
Protecting your vehicle's finish
Especially, with high-pressure
Washing
WARNING
water, water may leak through
the windows and wet the interi-
To help protect your vehicle's finish
After washing the vehicle, test
or.
from rust and deterioration, wash it
•
To prevent damage to the plastic
the brakes while driving slowly
thoroughly and frequently at least
parts, do not clean with chemi-
to see if they have been affected
once a month with lukewarm or cold
cal solvents or strong deter-
by water before getting on the
water.
road. If braking performance is
gents.
If you use your vehicle for off-road
impaired, dry the brakes by
driving, you should wash it after each
applying them lightly while
off-road trip. Pay special attention to
maintaining a slow forward
the removal of any accumulation of
speed.
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear and
clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle's
finish if not removed immediately.
7-78
High-pressure washing
Waxing
•
When using high-pressure wash-
A good coat of wax provides a barri-
ers, make sure to maintain suffi-
er between your paint and environ-
cient distance from the vehicle.
mental contamination.
Insufficient clearance or excessive
Keeping a good coat of wax on your
pressure can lead to component
vehicle will help protect it.
damage or water penetration.
Wax the vehicle when water will no
•
Do not spray the camera, sensors
longer bead on the paint.
or its surrounding area directly with
Always wash and dry the vehicle
a high pressure washer. Shock
before waxing. Use a good quality
applied from high pressure water
OJS078046
liquid or paste wax, and follow the
may cause the device to not oper-
manufacturer's instructions. Wax all
ate normally.
NOTICE
metal trim to protect it and to main-
•
Do not bring the nozzle tip close to
tain its luster.
• Water washing in the engine
boots (rubber or plastic covers)or
compartment including high
Removing oil, tar, and similar materi-
connectors as they may be dam-
pressure water washing may
als with a spot remover will usually
aged if they come into contact with
cause the failure of electrical cir-
strip the wax from the finish. Be sure
high pressure water.
cuits located in the engine com-
to re-wax these areas even if the rest
•
Do not use any high-pressure noz-
partment.
of the vehicle does not yet need wax-
zles, which induce either one-direct
ing.
• Never allow water or other liq-
7
water stream or water swirling.
uids to come in contact with
electrical/electronic
compo-
nents inside the vehicle as this
may damage them.
7-79