Volkswagen Corrado (1993 year). Manual - part 6

 

  Index      Volkswagen     Volkswagen Corrado - service repair manual 1993 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  4  5  6  7   ..

 

 

Volkswagen Corrado (1993 year). Manual - part 6

 

 

* ANTI-LOCK BRAKES UNIFORM INSPECTION GUIDELINE * 

         OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS

         It is MAP policy that all exhaust, brake, ABS, steering
and suspension, wheel alignment, tires and wheels, driveline,
engine performance and maintenance and heating, ventilation and air
conditioning services be offered and performed under the guidelines
and procedures specified in these sections.
         Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form.  The condition of the vehicle and its components will
indicate what services/part replacements may be required or suggested.
In addition, suggestions may be made to satisfy the needs expressed by
the customer.
         This section lists the various parts and conditions that
indicate required or suggested service or part replacement. Although
this list is extensive, it is not inclusive. In addition to this list,
a technician may make a suggestion. This suggestion must be based on
substantial and informed experience or the vehicle manufacturer's
recommended service interval.
         Some conditions indicate that service or part replacement
is required because the part in question is no longer providing
the function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.

      *  Example: An exhaust pipe has corroded severely and has a hole
         in it through which exhaust gases are leaking. Replacement of
         the exhaust pipe in this case is required due to functional
         failure.

      *  Example: A brake rotor has been worn to the point where it
         measures less than the vehicle manufacturer's specifications.
         Replacement of the rotor is required because it does not meet
         design specifications.

         Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or to address a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may
only be to suggest service.

      *  Example: An exhaust pipe is rusted, corroded or weak, but no
         leaks are present. In this case, the exhaust pipe has not
         failed. However, there is evidence that the pipe may need
         replacement in the near future. Replacement of the pipe may
         be suggested for the customer's convenience in avoiding a
         future problem.

      *  Example: The customer desires improved ride and/or handling,

* ANTI-LOCK BRAKES UNIFORM INSPECTION GUIDELINE * 

         A customer, of course, has the choice of whether or not a
Shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. The following reasons may be used for
required and suggested services:

         Reasons to Require Repair or Replacement:

      *  component no longer performs intended purpose
      *  component does not meet a design specification (regardless of
         performance)
      *  component is missing.

         Reasons to Suggest Repair or Replacement

      *  component is close to the end of its useful life (just above
         discard specifications or weak; failure likely to occur soon,
         etc.)
      *  address a customer need, convenience or request (stiffen
         ride, enhance performance, eliminate noise, etc.)
      *  comply with maintenance recommended by the vehicle's Original
         Equipment Manufacturer (OEM)
      *  technician's recommendation based on substantial and informed
         experience.

         BRAKE SERVICE PROCEDURES REQUIRED AND SUGGESTED

         FOR PROPER VEHICLE OPERATION

         ANTI-LOCK BRAKE SYSTEMS: GENERAL

         Anti-lock brake systems are considered an essential part of
brake systems on which they are found .
         Anti-lock brake systems are commonly referred to as "ABS"
and will be referred to as "ABS" throughout these guidelines. Some
ABS components also function as part of a traction control system
(TCS). Inspection, diagnostic and service procedures vary. Refer
to appropriate service manuals for vehicle's specific requirements.

WARNING: When diagnosing and servicing high pressure components,
         observe safety procedures and equipment requirements
         established by the vehicle manufacturer to reduce the
         possibility of serious personal injury.

CAUTION: Most manufacturers prohibit the use of DOT 5 brake fluid
         in a system equipped with ABS.

NOTE:    Intermittent electrical conditions are often caused by a
         loss of ground, poor connection, or water intrusion into

* ANTI-LOCK BRAKES UNIFORM INSPECTION GUIDELINE * 

         ABS: WHEEL SPEED OR VEHICLE SPEED SENSORS

ABS: WHEEL SPEED OR VEHICLE SPEED SENSORS

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition         

³

       Procedure        

³

         Note

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Improper output   

³

 Further inspection     

³

 Component failure may be

signal            

³

 required.              

³

 caused by water intrusion

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´

 into the wiring harness.

Internal          

³

 Require replacement.   

³

 Always check insulation

resistance        

³

                        

³

 for damage and wiring

does not meet     

³

                        

³

 for excessive resistance.

specifications    

³

                        

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Cracked sensor    

³

 Require replacement.   

³

housing           

³

                        

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Improper routing  

³

 Require re-routing     

³

of lead           

³

 according to vehicle   

³

                  

³

 manufacturer's         

³

                  

³

 specifications.        

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Damaged wire lead 

³

 Require replacement.   

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Contamination of  

³

 Suggest cleaning;      

³

surface           

³

 identify and correct   

³

                  

³

 source.                

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Damaged or missing

³

 Require replacement.   

³

tip or sensor     

³

                        

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Loose             

³

 Require adjustment     

³

 Some integral bearing

                  

³

 to vehicle manufac-    

³

 assemblies with sensors

                  

³

 turer's specifications.

³

 may require replacement.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Improper air gap  

³

 Require adjustment     

³

 If a sensor is not

                  

³

 to vehicle manufac-    

³

 adjustable further

                  

³

 turer's specifications.

³

 inspection is required

                  

³

                        

³

 to identify and correct

                  

³

                        

³

 cause.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         ABS: TOOTHED RING (TONE WHEEL)

ABS: TOOTHED RING (TONE WHEEL)

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition         

³

       Procedure        

³

         Note

* ANTI-LOCK BRAKES UNIFORM INSPECTION GUIDELINE * 

Teeth damaged     

³

 Further inspection     

³

 No action required unless

                  

³

 required.              

³

 ABS system performance is

                  

³

                        

³

 affected. If performance

                  

³

                        

³

 is affected, require

                  

³

                        

³

 replacement.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Cracked           

³

 Require replacement.   

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Teeth missing or  

³

 Require replacement.   

³

broken            

³

                        

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Loose             

³

 Require replacement    

³

                  

³

 of worn parts.         

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Contaminated      

³

 Suggest cleaning,      

³

                  

³

 identify and correct   

³

                  

³

 cause.                 

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Missing           

³

 Require replacement.   

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Improper alignment

³

 Require repair or      

³

                  

³

 replacement.           

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Bent              

³

 Require replacement.   

³

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Incorrect         

³

 Require replacement.   

³

 If the toothed ring

                  

³

                        

³

 requires replacement and

                  

³

                        

³

 cannot be replaced as a

                  

³

                        

³

 separate component,

                  

³

                        

³

 replace the assembly of

                  

³

                        

³

 which the ring is a part.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         ABS: FLUID LEVEL SENSOR SWITCH

ABS: FLUID LEVEL SENSOR SWITCH

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition                         

³

              Procedure

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Saturated float                   

³

  Require replacement.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Improper output                   

³

  Require replacement.

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

         ABS: PRESSURE SWITCHES

ABS: PRESSURE SWITCHES

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Condition           

³

                 Procedure

ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ

Leaks               

³

 Require tightening or replacement as necessary.

 

 

 

 

 

 

 

Content   ..  4  5  6  7   ..