Suzuki SX4 (2010 year). Instruction - part 5

 

  Index      Suzuki     Suzuki SX4 (2010 year) - instruction in english

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

Content      ..     3      4      5      6     ..

 

 

Suzuki SX4 (2010 year). Instruction - part 5

 

 

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Servicing the Air Bag System
To prevent damage or unintended inflation
If it is necessary to modify the advanced
If the air bags inflate, have the air bags and
of the air bag system, be sure the battery
front air bag system to accommodate a
related components replaced by an autho-
is disconnected and the ignition switch has
person with disabilities, owners in the con-
rized SUZUKI dealer as soon as possible.
been in the “LOCK” position for at least 90
tinental United States can call American
seconds before performing any electrical
Suzuki toll-free at 1-800-934-0934, or write
If your vehicle ever gets in deep water and
service work on your SUZUKI. Do not
to:
the driver’s floor is submerged, the air bag
touch air bag system components or wires.
controller could be damaged. If this hap-
American Suzuki Motor Corporation
The wires are wrapped with yellow tape or
pens, have the air bag system inspected
Automotive Customer Relations
yellow tubing, and the couplers are yellow
by the SUZUKI dealer as soon as possible.
3251 East Imperial Highway
for easy identification.
Brea, CA 92821-6795
Special procedures are required for servic-
Scrapping a car that has an undeployed air
ing or replacing an air bag. For that reason,
If you purchased your SUZUKI in Canada
bag can be hazardous. Ask your dealer,
only an authorized SUZUKI dealer should
please contact the Suzuki Canada Cus-
body repair shop or scrap yard for help
be allowed to service or replace your air
tomer Relations Department by telephone
with disposal.
bags. Please remind anyone who services
at
1-905-889-2677 extension 2254 or in
your SUZUKI that it has air bags.
writing at:
Service on or around air bag components
Suzuki Canada Inc.
or wiring must be performed only by an
Customer Relations
authorized SUZUKI dealer. Improper ser-
100 East Beaver Creek Road
vice could result in unintended air bag
Richmond Hill, On
deployment or could render the air bags
L4B 1J6
inoperative. Either of these two conditions
may result in severe injury.
2-58
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Instrument Cluster
1. Speedometer
2. Tachometer
3. Fuel gauge
4. Temperature gauge
5. Information display
6. Trip meter selector knob
7. Indicator selector knob
8. Warning and indicator lights
EXAMPLE
2
4
8
3
1
8
6
5
7
8
80J2020
2-59
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Warning and Indicator Lights
inflation pressure as specified in the vehi-
cle placard and owner’s instruction.
WARNING
Low Tire Pressure Warning Light
The low tire pressure warning light is also
The load rating of your tires is
used to inform you of a TPMS malfunction.
reduced at lower inflation pressures.
When the system detects a malfunction,
If your tires become even moderately
this light will flash for approximately one
under-inflated, the vehicle load may
minute and then remain continuously illu-
exceed the load rating of the tires,
minated. This sequence will be repeated
which can lead to tire failure. The low
approximately ten minutes after subse-
tire pressure warning light will not
quent the ignition switch is turned on as
alert you of this condition. The warn-
52D305
long as the malfunction exists.
ing light will only come on when one
As an added safety feature, your vehicle
or more of your tires become signifi-
has been equipped with a tire pressure
NOTE:
cantly under-inflated. Check and
monitoring system (TPMS) that uses a low
The low tire pressure warning light may not
adjust your tire inflation pressure at
tire pressure warning light to inform you
come on immediately if you have a sudden
least once a month. Refer to “Tires”
when one or more of your tires is signifi-
loss of air pressure.
in the
“INSPECTION AND MAINTE-
cantly under-inflated.
NANCE” section.
WARNING
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
If the low tire pressure warning light
you can check that the light is working.
does not come on when the ignition
is turned to the
“ON” position, or
When the low tire pressure warning light is
comes on and blinks while driving
lit, one or more of your tires is significantly
there may be a problem with the tire
under-inflated. You should stop and check
pressure monitoring system. Have
your tires as soon as possible, and inflate
your vehicle inspected by an autho-
them to the proper pressure as indicated
rized SUZUKI dealer. Even if the light
on the vehicle’s tire information placard.
turns off after blinking, indicating
Driving on a significantly under-inflated tire
that monitoring system has recov-
causes the tire to overheat and can lead to
ered, make sure to have an autho-
tire failure. Under-inflation also reduces
rized SUZUKI dealer check the
fuel efficiency and tire tread life, and may
system.
affect the vehicle’s handling and stopping
ability. Each tire, including the spare,
should be checked at least once a month
when cold and set to the recommended
2-60
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Refer to “Tire Pressure Monitoring System”
Brake System Warning Light
WARNING
in the “OPERATING YOUR VEHICLE” sec-
tion for additional details on the tire pres-
If the low tire pressure warning light
sure monitoring system. Refer to “Tires” in
comes on and stays on, reduce your
the “INSPECTION AND MAINTENANCE”
speed and avoid abrupt steering and
section for information
on
maintaining
braking. Stop in a safe place as soon
proper tire pressure.
as possible and check your tires.
• If you have a flat tire, replace it with
65D477
the spare tire. Refer to
“Jacking
Instructions” in the “EMERGENCY
This light comes on briefly when the igni-
SERVICE” section. Refer to
tion switch is turned to the “ON” position.
“Replacing Tires and/or Wheels”
The light also comes on under the follow-
for instructions on how to restore
ing conditions: 1) when the parking brake
normal operation of the tire pres-
is engaged and 2) when the fluid in the
sure monitoring system after you
brake fluid reservoir falls below the speci-
have had a flat tire.
fied level. The light should go out after fully
• If one or more of your tires is
releasing the parking brake, if the fluid
under-inflated, adjust the inflation
level in the brake fluid reservoir is ade-
pressure in all of your tires to the
quate.
recommended inflation pressure as
If this light and the ABS warning light stay
soon as possible.
on, or come on simultaneously when driv-
Be aware that driving on a signifi-
ing, then there may be something wrong
cantly under-inflated tire can cause
with both the rear brake proportioning
the tire to overheat and can lead to
valve function and anti-lock function of the
tire failure, and may affect steering
ABS.
control and brake effectiveness. This
If the brake system warning light comes on
could lead to an accident, resulting in
while you are driving the vehicle, it may
severe injury or death.
mean that there is something wrong with
the vehicle’s brake system. If this happens,
you should:
2-61
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
1) Pull off the road and stop carefully.
NOTE:
For details of the ABS, refer to “Anti-Lock
Because the disc brake system is self-
Brake System (ABS)” in the “OPERATING
WARNING
adjusting, the fluid level will drop as the
YOUR VEHICLE” section.
brake pads become worn.
Remember that stopping distance
Replenishing the brake fluid reservoir is
SLIP Indicator Light (if equipped)
may be longer, you may have to push
considered normal periodic maintenance.
harder on the pedal, and the pedal
may go down farther than normal.
Anti-Lock Brake System (ABS)
Warning Light
2) Test the brakes by carefully starting and
stopping on the shoulder of the road.
3) If you determine that it is safe, drive
cautiously at low speed to the nearest
52KM133
dealer for repairs,
or
ESP® is a registered trademark of Daimler
4) Have the vehicle towed to the nearest
AG.
dealer for repairs.
65D529
WARNING
When the ignition switch is turned to the
This light blinks 5 times per second when
“ON” position, the light comes on briefly so
one of the ESP® systems other than ABS
If any of the following conditions
you can check that the light is working. If
is activated. If this light blinks, drive care-
occur, you should immediately ask
the light stays on, or comes on when driv-
fully.
your SUZUKI dealer to inspect the
ing, there may be something wrong with
brake system.
When the ignition switch is turned to the
the ABS.
• If the brake system warning light
“ON” position, the light comes on briefly so
does not go out after the parking
If the ABS light and the brake system
you can check that the light is working. If
brake has been fully released.
warning light stay on, or come on simulta-
the light stays on, or comes on when driv-
• If the brake system warning light
neously when driving, then there may be
ing and remains on, there may be some-
does not come on when the igni-
something wrong with both the rear brake
thing wrong with the ESP® systems (other
tion switch is turned to the “ON”
proportioning valve function and anti-lock
than ABS). You should have the system
position.
function of the ABS.
inspected by an authorized SUZUKI
• If the brake system warning light
dealer.
If one of these happens, have the system
comes on at any time during vehi-
inspected by your SUZUKI dealer. If the
cle operation.
ABS becomes inoperative, the brake sys-
tem will function as an ordinary brake sys-
tem that has no ABS.
2-62
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
NOTE:
“ESP” (Electronic Stability
“ESP OFF” Indicator Light
When you disconnect and re-connect the
Program) Warning Light
(if equipped)
battery, ESP® system functions other than
(if equipped)
ABS will be deactivated and the slip indica-
tor light will blink 1 time per second. For
details on how to reactive the ESP® sys-
tems, refer to “SLIP Indicator Light” in the
“OPERATING YOUR VEHICLE” section.
For details of the ESP® systems, refer to
“Electronic Stability Program
(ESP®)” in
66J032
the “OPERATING YOUR VEHICLE” sec-
66J031
When the ignition switch is turned to the
tion.
When the ignition switch is turned to the
“ON” position, this light comes on briefly so
“ON” position, the light comes on briefly so
you can check that the light is working.
WARNING
you can check that the light is working. If
When the “ESP OFF” switch is pushed to
The ESP®
systems cannot prevent
the light stays on, or comes on when driv-
turn off the ESP® systems
(other than
accidents. Always drive carefully.
ing, there may be something wrong with
ABS), the “ESP OFF” light comes on and
the ESP® systems (other than ABS). You
stays on.
should have the system inspected by an
authorized SUZUKI dealer.
For details of the ESP® systems, refer to
“Electronic Stability Program
(ESP®)” in
For details of the ESP® systems, refer to
the “OPERATING YOUR VEHICLE” sec-
“Electronic Stability Program
(ESP®)” in
tion.
the “OPERATING YOUR VEHICLE” sec-
tion.
2-63
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Oil Pressure Light
Charging Light
Driver’s Seat Belt Reminder Light
50G051
50G052
60G049
This light comes on when the ignition
This light comes on when the ignition
If the driver’s seat belt is unbuckled when
switch is turned to the “ON” position, and
switch is turned to the “ON” position, and
the ignition switch is turned to the “ON”
goes out when the engine is started. The
goes out when the engine is started. The
position, this light will come on and then
light will come on and remain on if there is
light will come on and remain on if there is
blink. When the light comes on, a buzzer
insufficient oil pressure. If the light comes
something wrong with the battery charging
will also sound intermittently for about 6
on when driving, pull off the road as soon
system. If the light comes on when the
seconds. The reminder will repeat several
as you can and stop the engine. Check the
engine is running, the charging system
times under certain conditions until the
oil level and add oil if necessary. If there is
should be inspected immediately by your
driver’s seat belt is buckled. After repeating
enough oil, the lubrication system should
SUZUKI dealer.
several times, the reminder will be can-
be inspected by your SUZUKI dealer
celed even if the driver’s seat belt remains
before you drive the vehicle again.
unbuckled.
For details about the seat belt reminder,
CAUTION
refer to
“Seat Belts and Child Restraint
• If you operate the engine with this
Systems” in this section.
light on, severe engine damage can
result.
WARNING
• Do not rely on the Oil Pressure
It is absolutely essential that the
Light to indicate the need to add
driver and passengers wear their seat
oil. Be sure to periodically check
belts at all times. Persons who are
the engine oil level.
not wearing seat belts have a much
greater risk of injury if an accident
occurs. Make a regular habit of buck-
ling your seat belt before putting the
key in the ignition.
2-64
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
AIR BAG Light
Malfunction Indicator Light
CAUTION
Continuing to drive the vehicle when
the malfunction indicator light is on
or blinking can cause permanent
damage to the vehicle’s emission
control system, and can affect fuel
economy and driveability.
63J030
65D530
This light monitors inflators, crash sensors,
Your vehicle has a computer-controlled
NOTE:
seat belt pretensioners, the front passen-
emission control system. A malfunction
If the fuel filler cap is not installed fully, the
ger sensing system, and corresponding
indicator light is provided on the instrument
electrical system gets wet (such as by driv-
electrical circuits.
panel to indicate when it is necessary to
ing through a deep puddle of water) or the
This light blinks or comes on for several
have the emission control system serviced.
fuel tank gets nearly empty, the malfunc-
seconds when the ignition switch is turned
The malfunction indicator light comes on
tion indicator light may come on. If so, the
to the “ON” position so you can check if the
when the ignition switch is turned to the
light will go off after driving a few times
light is working. The light will come on and
“ON” position to let you know the light is
after the fuel filler cap is installed fully, the
stay on if there is a problem in the air bag
working and goes out when the engine is
electrical system dries out or the fuel tank
system or the seat belt pretensioner sys-
started.
is filled.
tem.
If the malfunction indicator light comes on
or blinks when the engine is running, ser-
WARNING
vice to the emission control system is nec-
If the AIR BAG light does not blink or
essary. Bring the vehicle to your SUZUKI
come on when the ignition switch is
dealer to have the emission control system
turned to the “ON” position or stays
serviced right away and avoid hard accel-
on or comes on when driving, the air
eration until the service is performed.
bag system or the seat belt preten-
Also, if the light comes on, there may be
sioner system may not work properly.
something wrong with the continuously
Have both systems inspected by an
variable transaxle system. Have the sys-
authorized SUZUKI dealer.
tem inspected by an authorized SUZUKI
dealer.
2-65
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Low Fuel Warning Light
If any door (including the tailgate of SX4) is
Keyless Start System Indicator
open when the vehicle is moving, a ding
Light (if equipped)
sounds to remind you to close all doors
completely.
“CRUISE” Indicator Light
(if equipped)
54G343
80JM122
If this light comes on, fill the fuel tank
immediately.
When you push the ignition switch for vehi-
When this light comes on, a ding sounds
cle with the keyless start system, this light
once to remind you to fill the fuel.
will come on in blue or red. If this light
If you do not fill the fuel, a ding sounds
comes on in blue, you can turn the ignition
52D113
every time when the ignition switch is
switch without using an ignition key. If this
turned to “ON”.
When the cruise control system is on, this
light comes on in red, you cannot turn the
light will be on.
ignition switch without using an ignition
NOTE:
key. For details, refer to “Ignition Switch” in
The activation point of this light varies
“SET” Indicator Light (if equipped)
the “OPERATING YOUR VEHICLE” sec-
depending on road conditions (for exam-
tion.
ple, slope or curve) and driving conditions
If this light blinks in red, it reminds you that
because of fuel moving in the tank.
the remote controller is not in the vehicle.
For details, refer to “Keyless Start System
Open Door Warning Light
Remote Controller/Keyless Entry System
Transmitter” in this section.
65D474
When the vehicle’s speed is controlled by
the cruise control system, this light will be
on.
54G391
This light remains on until all doors (includ-
ing the tailgate of SX4) are completely
closed.
2-66
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Illumination Indicator Light
High Beam Indicator Light
system inspected by an authorized
SUZUKI dealer.
If the oil temperature of the parts for i-AWD
system is high, this light will blink. The “i-
AWD AUTO” or “i-AWD LOCK” mode will
be changed to the “2WD” mode automati-
cally to prevent a damage of the parts for i-
AWD system.
64J045
50G056
This indicator light comes on while the
This indicator comes on when headlight
NOTE:
position lights, tail light and/or the head-
high beams are turned on.
If you restart the engine, the light will stop
lights are on.
blinking temporarily.
intelligent All Wheel Drive (i-AWD)
Turn Signal Indicators
AUTO Indicator Light (if equipped)
For details, refer to “Using the 2WD/i-AWD
Switch” in the “OPERATING YOUR VEHI-
CLE” section.
NOTE:
When the vehicle speed is increased, the
“i-AWD LOCK” mode will be changed to
the
“i-AWD AUTO” mode automatically.
The “i-AWD AUTO” indicator light will come
50G055
79J040
on and stay on.
When you turn on the left or right turn sig-
When the ignition switch is turned to the
nals, the corresponding green arrow on the
“ON” position, the light comes on briefly so
instrument panel will flash along with the
you can check that the light is working.
respective turn signal lights.
When the 2WD/i-AWD switch is in the “i-
When you turn on the hazard warning
AWD AUTO” mode with the ignition switch
switch, both arrows will flash along with all
in the “ON” position, the light comes on
of the turn signal lights.
and stays on.
If the light and the “i-AWD LOCK” indicator
light stay on or come on simultaneously
when driving, there may be something
wrong with the i-AWD system. Have the
2-67
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
intelligent All Wheel Drive (i-AWD)
For details of the
“i-AWD LOCK” mode,
Speedometer
LOCK Indicator Light (if equipped)
refer to “Using the 2WD/i-AWD Switch” in
the “OPERATING YOUR VEHICLE” sec-
EXAMPLE
tion.
CAUTION
Do not operate your vehicle in “i-
AWD LOCK” mode on dry hard sur-
faces.
79J100
When the ignition switch is turned to the
Daytime Running Light (D.R.L.) Indi-
“ON” position, this light comes on briefly so
cator Light (if equipped)
you can check that the light is working.
The light comes on when the 2WD/i-AWD
switch is changed to the “i-AWD LOCK”
80J2063
mode from the “i-AWD AUTO” mode.
The speedometer indicates vehicle speed
If the light and the “i-AWD AUTO” indicator
in km/h and mph.
light stay on or come on simultaneously
when driving, there may be something
60B245
wrong with the i-AWD system. Have the
With the D.R.L. system, the headlights
system inspected by an authorized
light, but are dimmer than the low beam,
SUZUKI dealer.
when the following three conditions are all
met. Whenever the D.R.L. system is oper-
NOTE:
ating, the D.R.L. indicator light remains on.
• When the vehicle speed is increased,
the “i-AWD LOCK” mode will be changed
Conditions for D.R.L. system operation
to the
“i-AWD AUTO” mode automati-
1) The engine is running.
cally. The “i-AWD AUTO” indicator light
2) The parking brake is released.
will come on and stay on.
3) The headlights are off.
• When the ignition switch is turned to the
“OFF” position, the “i-AWD LOCK” mode
is canceled.
2-68
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Tachometer
Fuel Gauge
If the low fuel warning light (1) comes on,
fill the fuel tank immediately.
When the low fuel warning light (1) comes
EXAMPLE
(2)
on, a ding sounds once to remind you to fill
the fuel.
If you do not fill the fuel, a ding sounds
every time when the ignition switch is
turned to “ON”.
CAUTION
(1)
Avoid driving with an extremely low
fuel level. Running out of fuel could
cause the engine to misfire, damag-
ing the catalytic converter.
80JM101
80JM102
NOTE:
The tachometer indicates engine speed in
When the ignition
switch is in
the “ON”
The activation point of the low
fuel warning
revolutions per minute.
position, this gauge gives an approximate
light (1) varies depending on
road condi-
indication of the amount of fuel
in the fuel
tions
(for example, slope
or
curve) and
CAUTION
tank. “F” stands for
full and “E”
stands for
driving conditions
because
of
fuel moving
empty.
in the tank.
Never drive with the engine speed
indicator in the red zone or severe
If the indicator gets
off the graduation of
The mark (2) indicates that the fuel filler
engine damage can result.
“E” (not character “E”), refill the tank as
door is located on the left side of the vehi-
soon as possible.
cle.
NOTE:
The indicator moves a little depending on
road conditions
(for example, slope or
curve) and driving conditions because of
fuel moving in the tank.
2-69
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Temperature Gauge
Information display
Display (E)
Clock (if equipped)
Instantaneous Fuel Consumption
The display (A)
shows instantaneous fuel
consumption
with a bar graph only when
the vehicle is
moving.
(A)
(C)
EXAMPLE
(B)
(D)
(E)
(1)
(3)
(2)
80J2026
80JM103
80JM104
NOTE:
When the
ignition switch is in the
“ON”
(1) Trip meter selector knob
• The display does not show the bar graph
position, this gauge
indicates the engine
(2) Indicator selector knob
unless the vehicle is moving.
coolant temperature.
Under normal driving
(3) Information display
• The indicated maximum value of instan-
conditions,
the indicator should stay within
taneous fuel consumption is
80. No
When the ignition switch is in the “ON”
more than 80 will be indicated on the dis-
the normal, acceptable temperature range
position, the information display shows the
between
“H” and
“C”. If the indicator
play even if the actual instantaneous fuel
following information.
consumption is higher.
approaches “H”, overheating is indicated.
Follow the instructions for engine overheat-
Display (A)
• The indication on the display may be
ing in the “EMERGENCY SERVICE” sec-
Instantaneous fuel consumption
delayed if fuel consumption is greatly
tion.
affected by driving conditions.
Display (B)
• The display shows estimated values.
Trip meter / Average fuel consumption /
Indications may not be the same as
CAUTION
Driving range / Thermometer
actual values.
Continuing to drive the vehicle when
Display (C)
engine overheating is indicated can
Transaxle selector position indicator
result in severe engine damage.
(for CVT)
Display (D)
Odometer / Illumination control setting
2-70
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
You can turn off or on the indication of
indication of instantaneous fuel con-
instantaneous fuel consumption according
sumption.
EXAMPLE
to the following instruction.
WARNING
(a)
EXAMPLE
If you attempt to adjust the display
while driving, you could lose control
of the vehicle.
Do not attempt to adjust the display
(b)
while driving.
NOTE:
80J2027
When you reconnect the negative (-) ter-
minal to the battery, the indication of the
1) Change the display (B) to the driving
instantaneous fuel consumption will be
range by pushing the indicator selector
(c)
reinitialized. Change the indication again to
knob (2).
your preference.
EXAMPLE
Trip meter / Average Fuel Consumption /
Driving Range / Thermometer
(d)
When the ignition switch is in the “ON”
(Initial
setting)
position, the display (B) shows one of the
following five indications, trip meter A, trip
meter B, average fuel consumption, driving
range or thermometer.
(e)
To switch the display indication (B), push
the trip meter selector knob (1) or the indi-
80J2029
cator selector knob (2) quickly.
Push
the
trip
meter
selector
80J2028
knob (1).
2) While pushing and holding the trip
Push the indicator
selector
meter selector knob (1), turn the indica-
knob (2).
tor selector knob (2) to turn off or on the
2-71
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
(a) Trip meter A
NOTE:
Driving range
(b) Trip meter B
The indicated maximum value of the trip
If you selected driving range the last time
(c) Average fuel consumption
meter is 9999.9. When you run past the
you drove the vehicle, the display indicates
(d) Driving range
maximum value, the indicated value will
---” for a few seconds and then indicates
(e) Thermometer
return to 0.0.
the current driving range when the ignition
switch is turned to the “ON” position.
WARNING
Average fuel consumption
The driving range shown in the display is
If you selected average fuel consumption
If you attempt to adjust the display
the approximate distance you can drive
the last time you drove the vehicle, the dis-
while driving, you could lose control
until the fuel gauge indicates “E”, based on
play shows the last value of average fuel
of the vehicle.
current driving conditions.
consumption from previous driving when
Do not attempt to adjust the display
the ignition switch is turned to the “ON”
When the remaining fuel in fuel tank
while driving.
position. Unless you reset the value of
reaches a low level, the display “---” will
average fuel consumption, the display indi-
appear.
NOTE:
cates the value of average fuel consump-
If the low fuel warning light comes on, fill
tion
which includes average fuel
• Indications will change when you push
the fuel tank immediately regardless of the
and release a knob.
consumption during previous driving.
value of driving range shown in the display.
• The display shows estimated values.
To reset the average fuel consumption to
Indications may not be the same as
As the driving range after refueling is cal-
zero, push and hold the indicator selector
actual values.
culated based on the most recent driving
knob (2) for a while when the display
condition, the value is different each time
shows the average fuel consumption.
Trip meter
you refuel.
The trip meter can be used to measure the
NOTE:
distance traveled on short trips or between
NOTE:
When you reset the indication or reconnect
fuel stops.
• If you refuel when the ignition switch is in
the negative (-) terminal to the battery, the
You can use the trip meter A or trip meter B
the “ON” position, the driving range may
value of average fuel consumption will be
independently.
not indicate the correct value.
shown after driving for a while.
• When you reconnect the negative (-) ter-
To reset the trip meter to zero, push and
minal to the battery, the value of driving
hold the trip meter selector knob (1) for a
range will be shown after driving for a
while when the display shows the trip
while.
meter.
2-72
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Thermometer
Transaxle selector position indicator
The thermometer indicates the outside
EXAMPLE
(for CVT)
temperature.
EXAMPLE
(h)
(g)
(Initial
EXAMPLE
(f)
setting)
80J2032
80J2030
When the ignition switch is in the “ON”
position, the display (C) indicates the gear
If the outside temperature nears freezing,
position (g).
the mark (f) will appear on the display.
When using the manual mode, the display
80J2031
(C) indicates the manual mode indicator
NOTE:
NOTE:
(h).
• The outside temperature indication is not
the actual outside temperature when
When you reconnect the negative (-) ter-
For details on how to use the transaxle,
driving at low speed, or when stopped.
minal to the battery, the unit of temperature
refer to
“Using the Transaxle” in the
• If there is something wrong with the ther-
will be reinitialized. Change the unit again
“OPERATING YOUR VEHICLE” section.
mometer, or just after the ignition switch
to your preference.
is turned to the “ON” position, the display
may not indicate the outside tempera-
ture.
• The mark (f) will appear whenever the
outside temperature is near freezing,
even if the display does not show the
thermometer.
To change the unit of temperature, while
pushing and holding the trip meter selector
knob (1), turn the indicator selector knob
(2).
2-73
80J23-03E

-------------------------------------------------------------------------------------------------------------------------------------------------------------

BEFORE DRIVING
Odometer / Illumination Control Setting
Illumination control setting
When the ignition switch is in the “ON”
When the ignition switch is turned to the
position, the display (D) shows the odome-
“ON” position, the instrument panel lights
(Brightest)
ter.
come on.
If you turn the indicator selector knob (2)
Your vehicle has a system to automatically
clockwise or counterclockwise, the display
dim the brightness of the instrument panel
will change to the illumination control set-
(Initial setting)
lights when the position lights or headlights
ting.
are on.
Odometer
You can change the brightness of the
The odometer records the total distance
instrument panel lights regardless of
the vehicle has been driven.
whether the position lights or headlights
are off or on.
CAUTION
To increase the brightness of the instru-
Keep track of your odometer reading
ment panel lights, turn the indicator selec-
and check the maintenance schedule
tor knob (1) clockwise.
regularly for required services.
To reduce the brightness of the instrument
Increased wear or damage to certain
panel lights, turn the indicator selector
parts can result from failure to per-
knob (1) counterclockwise.
form required services at the proper
mileage intervals.
(Dimmest)
80JM039
2-74
80J23-03E

 

 

 

 

 

 

 

Content      ..     3      4      5      6     ..