Nissan Versa Sedan. Instruction - part 810

TM-146

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P0706 TRANSMISSION RANGE SENSOR A

P0706 TRANSMISSION RANGE SENSOR A

DTC Logic

INFOID:0000000009267903

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn the ignition switch OFF and wait for

at least 10 seconds, then perform the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch to ON.

2. Shift the selector lever to the entire position from P to 1. (Hold the selector lever at each position for 20

seconds or more.)

3. Check the first trip DTC.
Is “P0706” detected?

YES

>> Go to 

TM-146, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009267904

1.

CHECK CONTROL CABLE

Check the control cable. Refer to 

TM-235, "Inspection and Adjustment"

.

Is the check result normal?

YES

>> GO TO 2.

NO

>> Adjust the control cable Refer to 

TM-235, "Inspection and Adjustment"

.

2.

CHECK POWER CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect the transmission range switch connector.

3. Turn the ignition switch ON.

4. Check the voltage between the transmission range switch harness connector and ground.

Is the check result normal?

YES

>> GO TO 3.

NO

>> GO TO 6.

3.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (CHECK 1)

1. Turn the ignition switch OFF.

2. Disconnect the TCM connector.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0706

Transmission Range Sensor 
“A” Circuit Range/Performance 

The following diagnosis condi-
tions are met and the position 
signal is OFF continuously for 
15 seconds or more.
• Diagnosis condition
- TCM power supply voltage: 

10 V <TCM power supply 
voltage <16 V

• Harness or connector

(Open circuit between trans-
mission position SW and 
TCM)

• Transmission position switch
• Control cable

Transmission range switch harness connector

Ground

Voltage

Connector

Terminal

F52

6

Ground

10 - 16 V

P0706 TRANSMISSION RANGE SENSOR A

TM-147

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3. Check the continuity between the transmission range switch harness connector and the TCM harness

connector.

Is the check result normal?

YES

>> GO TO 4.

NO

>> Repair or replace the malfunctioning parts.

4.

CHECK CIRCUIT BETWEEN TRANSMISSION RANGE SWITCH AND TCM (CHECK 2) 

Check the continuity between the transmission range switch harness connector and ground.

Is the check result normal?

YES

>> GO TO 5.

NO

>> Repair or replace the malfunctioning parts.

5.

CHECK TRANSMISSION RANGE SWITCH

Check the transmission range switch. Refer to 

TM-148, "Component Inspection (Transmission Range

Switch)"

.

Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning parts.

6.

CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH (CHECK 1)

1. Disconnect the IPDM E/R connector.

2. Check the continuity between the IPDM E/R harness connector and the transmission range switch.

Is the check result normal?

YES

>> GO TO 7.

NO

>> Repair or replace the malfunctioning parts.

7.

CHECK CIRCUIT BETWEEN IPDM E/R AND TRANSMISSION RANGE SWITCH (CHECK 2)

Check the continuity between the IPDM E/R harness connector and ground.

Transmission range switch harness connector

TCM harness connector

Continuity

Connector

Terminal

Connector

Terminal

F52

2

F44

3

Exists

3

2

4

4

5

6

8

5

9

7

Transmission range switch harness connector

Ground

Continuity

Connector

Terminal

F52

2

Ground

Does not exist

3

4

5

8

9

IPDM E/R harness connector

Transmission range switch harness connector

Continuity

Connector

Terminal

Connector

Terminal

E45

21

F52

6

Exists

TM-148

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

P0706 TRANSMISSION RANGE SENSOR A

Is the check result normal?

YES

>> GO TO 8.

NO

>> Repair or replace the malfunctioning parts.

8.

DETECTION OF MALFUNCTION ITEMS

Check the following items:

• Harness open circuit or short circuit between the ignition switch and IPDM E/R. Refer to 

PG-20, "Wiring Dia-

gram — Ignition Power Supply —"

.

• 10 A fuse (#49, IPDM E/R). Refer to 

PG-62, "IPDM E/R Terminal Arrangement"

.

• IPDM E/R
Is the check result normal?

YES

>> Check intermittent incident. Refer to 

GI-45, "Intermittent Incident"

.

NO

>> Repair or replace the malfunctioning parts.

Component Inspection (Transmission Range Switch)

INFOID:0000000009267905

1.

CHECK TRANSMISSION RANGE SWITCH

Check the continuity between the transmission range switch connector terminals.

Is the check result normal?

YES

>> INSPECTION END

NO

>> There is a malfunction of the transmission range switch. Replace the transaxle assembly. Refer to

TM-250, "Removal and Installation"

.

IPDM E/R harness connector

Ground

Continuity

Connector

Terminal

E45

21

Ground

Does not exist

Transmission range switch

Condition

Continuity

Terminal

7

10

Selector lever in “P”, “N” posi-
tion

Exists

Other than the above

Does not exist

6

9

Selector lever in “1” position

Exists

Other than the above

Does not exist

5

Selector lever in “2” position

Exists

Other than the above

Does not exist

8

Selector lever in “D” position

Exists

Other than the above

Does not exist

4

Selector lever in “N” position

Exists

Other than the above

Does not exist

2

Selector lever in “R” position

Exists

Other than the above

Does not exist

3

Selector lever in “P” position

Exists

Other than the above

Does not exist

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

TM-149

< DTC/CIRCUIT DIAGNOSIS >

[4AT: RE4F03C]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0711 TRANSMISSION FLUID TEMPERATURE SENSOR A

DTC Logic

INFOID:0000000009267906

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.

1.

PREPARATION BEFORE WORK

If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at

least 10 seconds, then perform the next test.

>> GO TO 2.

DTC

Trouble diagnosis name

DTC detection condition

Possible causes

P0711

Transmission Fluid Tempera-
ture Sensor “A” Circuit Range/
Performance

Under the following diagnosis 
conditions, A/T fluid tempera-
ture does not rise to 15

°C 

(59

°F) after driving for a certain 

period of time with the TCM-re-
ceived fluid temperature sensor 
value between 

−40°C (−40°F) 

and 14

°C (57.2°F).

• Diagnosis condition
- Selector lever: “D” position
- Vehicle speed: 10 km/h (7 

MPH) or more

- Engine speed: 450 rpm or 

more

- Accelerator pedal position: 

1.0/8 or more

- TCM power supply voltage: 

More than 11 V

A/T fluid temperature sensor

When the condition of the final 
judgment is satisfied after satis-
fying that of the provisional 
judgment:
• Provisional judgment: All of 

the following conditions are 
satisfied within 2 seconds af-
ter the ignition switch is 
turned ON.

- U0073, U0100, P0712 and 

P0713 are not detected.

• CAN communication is nor-

mal.

• TCM power supply voltage: 

More than 11 V

• The difference between A/T 

fluid temperature and engine 
coolant temperature is 38

°C 

(100.4

°F) or more, or −27°C 

(

−16.6°F) or less.

• Final judgment: When all of 

the following conditions are 
satisfied and this state is 
maintained for 300 seconds:

- ECM  is  normal.
- Provisional judgment is satis-

fied.

A/T fluid temperature sensor