Nissan Versa Sedan. Instruction - part 705

SEC-92

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210C STARTER CONTROL RELAY

NO

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

B210D STARTER RELAY

SEC-93

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210D STARTER RELAY

DTC Logic

INFOID:0000000009268442

DTC DETECTION LOGIC

NOTE:

If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to 

BCS-

59, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or

more.

-

Selector lever: In the P position

-

Brake pedal: Not depressed

2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-93, "Diagnosis Procedure"

.

NO

>> Inspection End

Diagnosis Procedure

INFOID:0000000009268443

Regarding Wiring Diagram information, refer to 

SEC-27, "Wiring Diagram"

.

1.

CHECK STARTER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch ON.

2. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK STARTER RELAY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect starter relay.

3. Disconnect BCM connector.

4. Check continuity between starter relay harness connector and BCM harness connector.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210D

STARTER RELAY ON

When comparing the following items, IPDM 
E/R detects that starter relay is stuck in the 
ON position for 1 second or more.
• Starter control relay signal (CAN) from 

BCM

• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/

R output)

• Transmission range switch signal input 

• Harness or connectors

(The CAN communication line is 
open or shorted.)

• Harness or connectors 

(Starter relay circuit is open or 
shorted.)

• IPDM  E/R
• BCM
• Starter relay

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M98

97

Ground

CVT selector lever

N or P position

Battery voltage

Other than above

0

SEC-94

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B210D STARTER RELAY

5. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK STARTER RELAY

Refer to 

SEC-94, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace starter relay.

4.

REPLACE BCM

1. Replace BCM. Refer to 

BCS-69, "Removal and Installation"

.

2. Perform initialization of BCM and registration of all Intelligent keys using CONSULT.

3. Perform DTC CONFIRMATION PROCEDURE for DTC B210D. Refer to 

SEC-93, "DTC Logic"

.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace IPDM E/R. Refer to 

PCS-30, "Removal and Installation"

.

Component Inspection

INFOID:0000000009268444

1.

CHECK STARTER RELAY

1. Turn ignition switch OFF.

2. Disconnect starter relay.

3. Check continuity between starter relay terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace starter relay.

Starter relay

BCM

Continuity

Connector

Terminal

Connector

Terminal

E41

1

M98

97

Yes

Starter relay

Ground

Continuity

Connector

Terminal

E41

1

No

Starter relay

Condition

Continuity

Terminal

3

5

12 V direct current supply between terminals 1 and 2

Yes

No current supply

No

B210E STARTER RELAY

SEC-95

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

B210E STARTER RELAY

DTC Logic

INFOID:0000000009268445

DTC DETECTION LOGIC

NOTE:

• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

BCS-59, "DTC Logic"

.

• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to

BCS-60, "DTC Logic"

.

• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be

detected.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1. Press push-button ignition switch under the following conditions to start engine, and wait 1 second or

more.

-

Selector lever: In the P position

-

Brake pedal: Not depressed

2. Check DTC in Self Diagnostic Result mode of IPDM E/R using CONSULT.
Is DTC detected?

YES

>> Go to 

SEC-95, "Diagnosis Procedure"

.

NO

>> Inspection End.

Diagnosis Procedure

INFOID:0000000009268446

Regarding Wiring Diagram information, refer to 

SEC-27, "Wiring Diagram"

.

1.

CHECK STARTER RELAY OUTPUT SIGNAL

1. Check voltage between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT

1. Turn ignition switch OFF.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B210E

STARTER RELAY OFF

When comparing the following items, IPDM E/R 
detects that starter relay is stuck in the OFF po-
sition for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status 

signal (IPDM E/R input)

• Starter control relay control signal (IPDM E/R 

output)

• Transmission range switch signal input 

• Harness or connectors

(The CAN communication line is open 
or shorted.)

• Harness or connector

(Starter relay circuit is open or shorted.)

• IPDM E/R
• Battery
• BCM
• Starter relay

(+)

(–)

Condition

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M98

97

Ground

CVT shift selector lever

N or P position

Battery voltage

Other than above

0