Nissan Versa Sedan. Instruction - part 681

SE-50

< UNIT DISASSEMBLY AND ASSEMBLY >

REAR SEAT

Disassembly and Assembly - Seat Cushion

INFOID:0000000009268538

SEAT CUSHION

Disassembly

1. Remove the seat cushion assembly. Refer to 

SE-23, "Removal and Installation - Seat Cushion Assembly"

.

2. Remove the hog rings on the bottom side of seat cushion.
3. Remove the hog rings on the top side of seat cushion and separate the seat cushion trim from the seat

cushion pad.

NOTE:

Remove all pieces of hog rings and discard them.

Assembly

Assembly is in the reverse order of disassembly. 

CAUTION:

• Make sure hog rings are correctly fastened around both the seat cushion trim and seat cushion pad

wires.

• Replace any deformed or damaged hog rings.

• Make sure any old hog ring pieces are removed from seat.

NOTE:

13. Seat cushion pad

14. Seat cushion hook

15. Seatback hinge assembly

16. Rear seat bolster (LH)

17. Seatback pad (LH)

18. Seatback trim (LH)

19. Seatback latch assembly (LH)

20. Seatback striker

21. Rear seatback frame (LH)

22. Rear seatback assembly (LH)

A.

Seatback hinge finisher clips

ALJIA0984ZZ

1.

Seat cushion pad

2.

Seat cushion trim

A.

Hog rings

REAR SEAT

SE-51

< UNIT DISASSEMBLY AND ASSEMBLY >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

• Install new hog rings on the seat cushion trim in original positions. 

• Use only one hog ring in each designated location.

Disassembly and Assembly - Fixed Seatback

INFOID:0000000009268539

FIXED SEATBACK

Disassembly

1. Remove the rear seatback assembly. Refer to 

SE-23, "Removal and Installation - Fixed Seatback"

.

2. Release locks as shown and remove the headrest holders.

CAUTION:

Before removing/installing the headrest holder, check its

orientation (front/rear and right/left)

3. Remove the hog rings from the back side of the rear seatback assembly.

PIIB3356J

ALJIA0983ZZ

1.

Seatback pad

2.

Seatback trim

A.

Hog rings

PIIB4084J

SE-52

< UNIT DISASSEMBLY AND ASSEMBLY >

REAR SEAT

4. Remove the hog rings from the front side of the rear seatback assembly and separate the seatback trim

from the seatback pad.

NOTE:

Remove all pieces of hog rings and discard them.

Assembly

Assembly is in the reverse order of disassembly.

CAUTION:

• Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.

• Replace any deformed or damaged hog rings.

• Make sure any old hog ring pieces are removed from seat.

NOTE:

• Install new hog rings on the seatback trim in original positions. 

• Use only one hog ring in each designated location.

Disassembly and Assembly - Split Seatback

INFOID:0000000009268540

DISASSEMBLY

1. Remove the rear seatback assembly. Refer to 

SE-23, "Removal and Installation - 60:40 Split Seatback"

.

2. Rotate the seatback latch release knob (1) counterclockwise

and remove.

3. Release the J-hook retainer (C), the clips (A), and unzip the

seatback trim zippers (B).

PIIB3356J

AWJIA0904ZZ

AWJIA0905ZZ

REAR SEAT

SE-53

< UNIT DISASSEMBLY AND ASSEMBLY >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

4. Reach up through the seatback trim and release locks as shown

and remove the headrest holders.

CAUTION:

Before removing/installing the headrest holder, check its

orientation (front/rear and right/left).

5. Remove the seatback trim and seatback pad from the seatback frame.
6. Separate the seatback trim from the seatback pad.
a. Remove the hog rings and separate the seatback trim from the

seatback pad.

: Hog ring

(1) Seatback trim (LH)

(2) Seatback trim (RH)

NOTE:

Remove all pieces of hog rings and discard them.

7. Remove the bolts (A) and the rear seatback latch assembly (1)

from the seatback frame (2).

Assembly

Assembly is in the reverse order of disassembly.

CAUTION:

• Make sure hog rings are correctly fastened around both the seatback trim and seatback pad wires.

• Replace any deformed or damaged hog rings.

• Make sure any old hog ring pieces are removed from seat.

NOTE:

PIIB4084J

ALJIA0986ZZ

ALJIA0700ZZ