Nissan Versa Sedan. Instruction - part 678

SE-38

< UNIT DISASSEMBLY AND ASSEMBLY >

FRONT SEAT

PASSENGER SIDE : Exploded View

INFOID:0000000009268533

WITH REMOVABLE HEADREST

ALJIA1000ZZ

1.

Seatback trim

2.

Seatback pad

3.

Headrest

4.

Headrest holder (free)

5.

Headrest holder (locked)

6.

Chute rod

7.

Seat frame assembly

8.

Side air bag module

9.

Recline lever

FRONT SEAT

SE-39

< UNIT DISASSEMBLY AND ASSEMBLY >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

WITHOUT REMOVABLE HEADREST

10. Seat cushion outer finisher (RH)

11. Seat cushion trim

12. Seat cushion pad

13. Seat belt buckle

14. Seat cushion outer finisher (LH)

ALJIA0999ZZ

1.

Seatback trim

2.

Seatback pad

3.

Chute rod

4.

Side air bag module

5.

Recline lever

6.

Seat cushion outer finisher (RH)

SE-40

< UNIT DISASSEMBLY AND ASSEMBLY >

FRONT SEAT

PASSENGER SIDE : Disassembly and Assembly

INFOID:0000000009268534

SEATBACK ASSEMBLY

WARNING:

Do not leave any objects (screwdrivers, tools, etc.) on the seat during seatback repair. It can lead to

personal injury if the side air bag should accidentally deploy.

CAUTION:

• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least three

minutes.

• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,

do not let it hang by the wire harness.

• Always work from the side or back of the seatback assembly, do not work in front of seat.

• Do not use air tools or electric tools for servicing the seat assembly.

• Replace the side air bag module if it has been dropped or sustained an impact.

• Do not insert any objects into the side air bag module.

• Do not attempt to disassemble the side air bag module.

• Do not expose the side air bag module to temperatures exceeding 93

°C (200°F).

• Do not expose the side air bag module to any oil, grease, detergent or water.

• During disassembly, do not damage the seatback board, chutes, connectors, retainers, clips, module

harness or the side air bag module.

NOTE:

If the vehicle has been involved in a collision and the side air bag module has deployed, the front seatback

assembly must be replaced. 

Disassembly

1. Remove the front seat assembly. Refer to 

SE-20, "PASSENGER SIDE : Removal and Installation"

.

2. Release the lower seatback trim retainer strap (A) from the

cushion springs.

3. Release the J-hook retainer (C), unzip seatback zipper (A) and

release J-clips (B) holding the seatback trim to the seat frame

assembly.

7.

Seat cushion trim

8.

Seat cushion pad

9.

Seat belt buckle

10. Seat cushion outer finisher (LH)

11. Seat frame assembly

AWJIA0913ZZ

AWJIA0914ZZ

FRONT SEAT

SE-41

< UNIT DISASSEMBLY AND ASSEMBLY >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

4. Reach up through the seatback trim and release locks as shown

and remove the headrest holders (if equipped).

CAUTION:

Before removing/installing the headrest holder, check its

orientation (front/rear and right/left)

5. Remove and discard the two chute rod nuts (A), then route the

chute rod (1) through the opening and remove it from the chute

(B). 

CAUTION:

Do not reuse the chute rod nuts.

6. Release the side air bag module harness from the seat frame

assembly.

NOTE:

Take note of harness routing and attachment location for accu-

rate installation.

a. From the back of the seat unclip the side air bag module har-

ness clips (

).

7. Remove and discard the two side air bag module nuts (A). 

CAUTION:

Do not reuse the side air bag module nuts.

8. Disengage the side air bag module studs from the seatback frame and lift the seatback trim and seatback

pad as an assembly from the seat frame assembly.

PIIB4084J

AWJIA0922ZZ

AWJIA0915ZZ

AWJIA0916ZZ