Nissan Versa Sedan. Instruction - part 673

SE-18

< REMOVAL AND INSTALLATION >

FRONT SEAT

PASSENGER SIDE : Exploded View

INFOID:0000000009268520

WITH REMOVABLE HEADREST

ALJIA1000ZZ

1.

Seatback trim

2.

Seatback pad

3.

Headrest

4.

Headrest holder (free)

5.

Headrest holder (locked)

6.

Chute rod

7.

Seat frame assembly

8.

Side air bag module

9.

Recline lever

FRONT SEAT

SE-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

WITHOUT REMOVABLE HEADREST

10. Seat cushion outer finisher (RH)

11. Seat cushion trim

12. Seat cushion pad

13. Seat belt buckle

14. Seat cushion outer finisher (LH)

ALJIA0999ZZ

1.

Seatback trim

2.

Seatback pad

3.

Chute rod

4.

Side air bag module

5.

Recline lever

6.

Seat cushion outer finisher (RH)

SE-20

< REMOVAL AND INSTALLATION >

FRONT SEAT

PASSENGER SIDE : Removal and Installation

INFOID:0000000009268521

REMOVAL

WARNING:

Do not leave any objects (screwdrivers, tools, etc.) on the seat during seat repair. It can lead to per-

sonal injury if the side air bag module should accidentally deploy.

CAUTION:

• When removing or installing the seat trim, handle it carefully to keep dirt out and to avoid damage.

• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connec-

tor with the side air bag module connector. Such an error may cause the air bag module to deploy.

• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with

care.

• After the front side air bag module inflates, the front seatback assembly must be replaced.

• When removing and installing the seat, use shop cloths to protect components from damage.

• Before removing the front seat, turn the ignition switch OFF, disconnect both battery cables and wait

at least three minutes.

1. Disconnect the negative and positive battery terminals and wait at least three minutes. Refer to 

PG-63,

"Removal and Installation"

.

2. Slide the seat to the full forward position.
3. Remove the two rear seat bolts.
4. Slide the seat to the full rearward position.
5. Remove the two front seat bolts.
6. Tilt the seat rearward to disconnect the harness connectors from the seat and remove.

INSTALLATION

Installation is in the reverse order of removal.

WARNING:

• Perform additional services when installing front passenger seat. Refer to 

SRC-37, "ZERO POINT

RESET : Description"

.

• Zero point reset must be performed every time the front passenger seat is removed from the vehicle.

• Zero point reset is done after the front passenger seat is installed in vehicle and all bolts are tight-

ened to specification.

CAUTION:

Make sure that the seat harness or the floor trim is not damaged during installation. 

NOTE:

• When installing the RH front seat, tighten the bolts in the order

shown.

7.

Seat cushion trim

8.

Seat cushion pad

9.

Seat belt buckle

10. Seat cushion outer finisher (LH)

11. Seat frame assembly

RH front seat bolt torque

: 40 Nm (4.1 kg-m, 30 ft-lb)

AWJIA0921ZZ

REAR SEAT

SE-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

K

L

M

A

B

SE

N

O

P

REAR SEAT

Exploded View - Fixed Seatback

INFOID:0000000009268522

FIXED SEATBACK

ALJIA0982ZZ

1.

Headrest holder (locked)

2.

Headrest holder (free)

3.

Rear seatback assembly

4.

Seatback trim

5.

Seatback pad

6.

LATCH bracket (RH)

7.

Seat cushion assembly

8.

Seat cushion trim

9.

Seat cushion pad

10. Seat cushion hook

11. LATCH bracket (LH)

12. Headrest