Nissan Versa Sedan. Instruction - part 665

RSU-10

< REMOVAL AND INSTALLATION >

REAR SHOCK ABSORBER

CAUTION:

Dispose of drained oil according to the law and local regulations.

COIL SPRING

RSU-11

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

COIL SPRING

Exploded View

INFOID:0000000009267422

Removal and Installation

INFOID:0000000009267423

REMOVAL

1. Remove the wheel and tire assemblies using power tool. Refer to 

WT-39, "Adjustment"

.

2. Position a suitable jack under rear suspension beam.

CAUTION:

• Place the jack in the center of the suspension beam.

• Do not damage the suspension beam with jack.

3. Remove the lower shock absorber bolts. Refer to 

RSU-8, "Removal and Installation"

.

4. Slowly lower jack, then remove upper rubber seat, coil spring and lower rubber seat from rear suspension

beam.

INSTALLATION

Installation is in the reverse order of removal.

• Install the lower rubber seat (A) to the rear suspension beam

mounting hole (B).

• Match up lower rubber seat indentions and rear suspension beam

grooves and attach.

Inspection

INFOID:0000000009267424

INSPECTION AFTER REMOVAL

Check rubber seat and coil spring for deformation, crack, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1.

Upper rubber seat

2.

Coil spring

3.

Lower rubber seat

4.

Rear suspension beam

JPEIB0162ZZ

JPEIB0223ZZ

RSU-12

< REMOVAL AND INSTALLATION >

COIL SPRING

Check wheel alignment. Refer to 

RSU-6, "Inspection"

.

REAR SUSPENSION BEAM

RSU-13

< REMOVAL AND INSTALLATION >

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

REAR SUSPENSION BEAM

Exploded View

INFOID:0000000009267425

Removal and Installation

INFOID:0000000009267426

REMOVAL

1. Remove the wheel and tire assemblies using power tool. Refer to 

WT-39, "Adjustment"

.

2. Remove wheel sensor and sensor harness. Refer to 

BRC-105, "REAR WHEEL SENSOR : Removal and

Installation"

.

3. Remove brake hose and brake pipe from rear suspension beam. Refer to 

BR-25, "REAR : Removal and

Installation"

.

4. Remove the rear drum brake assemblies. Refer to 

BR-41, "Removal and Installation"

.

5. Remove parking brake cable from rear suspension beam. Refer to 

PB-6, "Removal and Installation"

.

6. Position a suitable jack under rear suspension beam.

CAUTION:

• Place the jack in the center of the suspension beam.

• Do not damage the suspension beam with jack.

7. Remove shock absorber bolts (lower side). Refer to 

RSU-8, "Removal and Installation"

.

8. Remove coil spring. Refer to 

RSU-11, "Removal and Installation"

.

9. Remove rear suspension beam bolts and nuts.
10. Slowly lower jack, remove rear suspension beam from vehicle body.

CAUTION:

While lowering the rear suspension beam with the jack, be sure to maintain the stability of the

jack.

INSTALLATION

Installation is in the reverse order of removal.

• Perform final tightening of rear suspension beam installation position (rubber bushing), under unladen condi-

tions with tires on level ground.

• Check wheel sensor harness for proper connection. Refer to 

BRC-105, "REAR WHEEL SENSOR :

Exploded View"

.

• Adjust parking brake. Refer to 

PB-4, "Inspection and Adjustment"

.

• Check wheel alignment. Refer to 

RSU-6, "Inspection"

.

1.

Rear suspension beam

JPEIB0254GB