Nissan Versa Sedan. Instruction - part 598

MWI

DTC B2205 VEHICLE SPEED CIRCUIT

MWI-91

< DTC/CIRCUIT DIAGNOSIS >

[TYPE B]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DTC B2205 VEHICLE SPEED CIRCUIT

Description

INFOID:0000000009266529

The ABS actuator and electric unit (control unit) provides a vehicle speed signal to the combination meter via

CAN communication lines.

DTC Logic

INFOID:0000000009266530

Diagnosis Procedure

INFOID:0000000009266531

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Start engine and select METER/M&A on CONSULT.

2. Using SPEED METER on DATA MONITOR, compare the DATA MONITOR value with the combination

meter speedometer. Speedometer and DATA MONITOR indications should be close.

Is the inspection result normal?

YES

>> Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to 

BRC-32, "CONSULT

Function (ABS)"

.

NO

>> Replace combination meter. Refer to 

MWI-104, "Removal and Installation"

.

DTC

CONSULT

Detection condition

Possible malfunction location

B2205

VEHICLE SPEED CIRC
[B2205]

Malfunction is detected when an erroneous 
speed signal is received for 2 seconds or 
more.

• Combination meter
• ABS actuator and electric unit (control unit)

MWI-92

< DTC/CIRCUIT DIAGNOSIS >

[TYPE B]

B2267 ENGINE SPEED

B2267 ENGINE SPEED

Description

INFOID:0000000009266532

The engine speed signal is transmitted from ECM to the combination meter via CAN communication.

DTC Logic

INFOID:0000000009266533

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009266534

1.

CHECK COMBINATION METER INPUT SIGNAL

1. Start engine and select METER/M&A on CONSULT.

2. Using TACHO METER on DATA MONITOR, compare the value of DATA MONITOR with tachometer of

combination meter. Tachometer and DATA MONITOR indications should be close.

Is the inspection result normal?

YES

>> Perform ECM self-diagnosis. Refer to 

EC-61, "CONSULT Function"

.

NO

>> Replace combination meter. Refer to 

MWI-104, "Removal and Installation"

.

DTC

CONSULT

Diagnostic item is detected when...

Probable malfunction location

B2267

ENGINE SPEED

Malfunction is detected when an erroneous 
engine speed signal is recieved for 2 seconds 
or more. 

• Crankshaft position sensor (POS)
• ECM

MWI

B2268 WATER TEMP

MWI-93

< DTC/CIRCUIT DIAGNOSIS >

[TYPE B]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

B2268 WATER TEMP

Description

INFOID:0000000009266535

The engine coolant temperature signal is transmitted from ECM to the combination meter via CAN communi-

cation.

DTC Logic

INFOID:0000000009266536

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000009266537

1.

PERFORM SELF-DIAGNOSIS OF ECM

Perform “Self Diagnosis Result” of “ENGINE”, and repair or replace malfunctioning parts.

>> Refer to 

EC-61, "CONSULT Function"

.

DTC

CONSULT

Detection Condition

Possible malfunction location

B2268

WATER TEMP

ECM continuously transmits abnormal engine 
coolant temperature signals for 60 seconds or 
more 

• Engine coolant temperature sensor
• ECM

MWI-94

< DTC/CIRCUIT DIAGNOSIS >

[TYPE B]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

COMBINATION METER
COMBINATION METER : Diagnosis Procedure

INFOID:0000000009266538

Regarding Wiring Diagram information, refer to 

MWI-77, "Wiring Diagram"

.

1.

CHECK FUSE

Check for blown combination meter fuses.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the fuse after repairing the affected circuit.

2.

POWER SUPPLY CIRCUIT CHECK

1. Disconnect combination meter connector.

2. Check voltage between combination meter harness connector M82,  terminals 27, 28, 15 and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Check harness for open between combination meter and fuse.

3.

GROUND  CIRCUIT CHECK

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check continuity between combination meter harness connector M82, terminals 21, 22, 23 and ground.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Check ground harness.

BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)

Power source

Fuse No.

Battery

8

Ignition switch ON or START 

3

Ignition switch ACC or ON 

18

Terminals

Ignition switch position

(+)

(–)

OFF

ACC

ON

START

Connector

Terminal

M82

27

Ground

Battery voltage

Battery voltage

Battery

 voltage

Battery voltage

28

0V

0V

Battery
voltage

Battery voltage

15

0V

Battery voltage

Battery 
voltage

0V

Terminals

Continuity

(+)

(–)

Connector

Terminal

M82

21

Ground

Yes

22

23