Nissan Versa Sedan. Instruction - part 542

LAN-46

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

EPS BRANCH LINE CIRCUIT

EPS BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000009269367

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the EPS control unit for damage, bend and loose connection (unit

side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of EPS control unit.

2. Check the resistance between the EPS control unit harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the EPS control unit branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the EPS control unit. Refer to 

STC-21, "Diagnosis Proce-

dure"

.

Is the inspection result normal?

YES (Present error)>>Replace the EPS control unit. Refer to 

STC-40, "Removal and Installation"

.

YES (Past error)>>Error was detected in the EPS control unit branch line.

NO

>> Repair the power supply and the ground circuit.

EPS control unit harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M53

2

1

Approx. 54 – 66

LAN

M&A BRANCH LINE CIRCUIT

LAN-47

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

M&A BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000009269368

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the combination meter for damage, bend and loose connection

(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of combination meter.

2. Check the resistance between the combination meter harness connector terminals.

NOTE:

Check the vehicle type confirm the service information. Refer to 

MWI-55, "Information"

.

-

Models with Type A

-

Models with Type B

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the combination meter branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the combination meter. Refer to the following.

• TYPE A: 

MWI-44, "COMBINATION METER : Diagnosis Procedure"

• TYPE B: 

MWI-94, "COMBINATION METER : Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the combination meter. Refer to the following.

• TYPE A: 

MWI-53, "Removal and Installation"

• TYPE B: 

MWI-104, "Removal and Installation"

YES (Past error)>>Error was detected in the combination meter branch line.

NO

>> Repair the power supply and the ground circuit.

Combination meter harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M82

1

2

Approx. 54 – 66

Combination meter harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M24

8

10

Approx. 54 – 66

LAN-48

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

STRG BRANCH LINE CIRCUIT

STRG BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000009269369

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection

(unit side and connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of steering angle sensor.

2. Check the resistance between the steering angle sensor harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the steering angle sensor branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the steering angle sensor. Refer to 

BRC-45, "Wiring Dia-

gram"

.

Is the inspection result normal?

YES (Present error)>>Replace the steering angle sensor. Refer to 

BRC-111, "Removal and Installation"

.

YES (Past error)>>Error was detected in the steering angle sensor branch line.

NO

>> Repair the power supply and the ground circuit.

Steering angle sensor harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M64

5

2

Approx. 54 – 66

LAN

BCM BRANCH LINE CIRCUIT

LAN-49

< DTC/CIRCUIT DIAGNOSIS >

[CAN]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000009269370

1.

CHECK CONNECTOR

1. Turn the ignition switch OFF.

2. Disconnect the battery cable from the negative terminal.

3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and

connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1. Disconnect the connector of BCM.

2. Check the resistance between the BCM harness connector terminals.

-

Models with Intelligent Key system

-

Models without Intelligent Key system

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the BCM branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the BCM. Refer to the following.

• Models with Intelligent Key system: 

BCS-63, "Diagnosis Procedure"

• Models without Intelligent Key system: 

BCS-116, "Diagnosis Procedure"

Is the inspection result normal?

YES (Present error)>>Replace the BCM. Refer to the following.

• Models with Intelligent Key system: 

BCS-69, "Removal and Installation"

• Models without Intelligent Key system: 

BCS-122, "Removal and Installation"

YES (Past error)>>Error was detected in the BCM branch line.

NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M97

39

40

Approx. 108 – 132

BCM harness connector

Resistance (

Ω)

Connector No.

Terminal No.

M18

39

40

Approx. 108 – 132