Nissan Versa Sedan. Instruction - part 437

EXT-34

< REMOVAL AND INSTALLATION >

REAR SPOILER

• Before installing, be sure there are no gaps or waves in the adhesive-backed foam tape where the surfaces

meet.

• During installation, be sure harness grommet of high-mounted stop lamp is fully seated into trunk lid opening

prior to final rear spoiler placement.

FAX-1

TRANSMISSION & DRIVELINE

C

E

F

G

H

I

J

K

L

M

SECTION 

FAX

A

B

FAX

N

O

P

CONTENTS

FRONT AXLE

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...................................................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Special Service Tools ................................................

3

Commercial Service Tools  ........................................

4

SYMPTOM DIAGNOSIS  ...............................

6

NOISE, VIBRATION AND HARSHNESS 
(NVH) TROUBLESHOOTING  .............................

6

NVH Troubleshooting Chart  ......................................

6

PERIODIC MAINTENANCE ..........................

7

FRONT WHEEL HUB AND KNUCKLE  ..............

7

Inspection ..................................................................

7

FRONT DRIVE SHAFT ........................................

8

Inspection ..................................................................

8

REMOVAL AND INSTALLATION ................

9

FRONT WHEEL HUB AND KNUCKLE  .............

9

Exploded View ..........................................................

9

Removal and Installation  ..........................................

9

Disassembly and Assembly .....................................

11

Inspection ................................................................

13

FRONT DRIVE SHAFT  .....................................

15

Exploded View .........................................................

15

Removal and Installation  .........................................

15

UNIT DISASSEMBLY AND ASSEMBLY  ....

18

FRONT DRIVE SHAFT  .....................................

18

Exploded View .........................................................

18

Disassembly and Assembly .....................................

18

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

24

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

24

Wheel Bearing  .........................................................

24

Drive Shaft ...............................................................

24

Dynamic Damper .....................................................

25

Boot Bands  ..............................................................

25

FAX-2

< PRECAUTION >

PRECAUTIONS

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000009268290

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Man-

ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Service Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

PREPARATION

FAX-3

< PREPARATION >

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000009268291

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number 
(Kent-Moore No.)
Tool name

Description

KV40104000
(

—

)

Hub lock nut wrench

Removing and Installing wheel hub lock nut
a: 85 mm (3.35 in)
b: 65 mm (2.56 in)

ST33710000
(

—

)

Drift

Removing wheel hub
a: 30 mm (1.18 in) dia.
b: 23 mm (0.91 in) dia.

ST30031000
(

—

)

Puller

Removing wheel bearing inner race (outer)

ST35321000
(

—

)

Drift

• Removing wheel bearing
• Installing wheel hub
a: 49 mm (1.93 in) dia.
b: 41 mm (1.61 in) dia.

ST35271000
(

—

)

Drift

Installing wheel bearing
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.

ST33061000
(

—

)

Drift

Installing wheel hub
a: 38 mm (1.50 in) dia.
b: 28.5 mm (1.122 in) dia.

ZZA0802D

ZZA1233D

ZZA0700D

ZZA1051D

ZZA0837D

ZZA1051D