Nissan Versa Sedan. Instruction - part 235

DLK-258

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

HORN FUNCTION

Is the inspection result normal?

YES

>> GO TO 4

NO

>> Repair or replace harness.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to 

PCS-56, "Removal and Installation"

.

NO

>> Repair or replace the malfunctioning part.

IPDM E/R

Ground

Continuity 

Connector

Terminal

E46

73

Ground

No

WARNING CHIME FUNCTION

DLK-259

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

WARNING CHIME FUNCTION

Description

INFOID:0000000009268962

Performs operation method guide and warning with buzzer.

Component Function Check

INFOID:0000000009268963

1.

CHECK FUNCTION

 With CONSULT

1. Check the operation with “BUZZER” in the Active Test.

2. Touch “IGN KEY WARN ALM”, “SEAT BELT WARN TEST”or “LIGHT WARN ALM”on screen.
Is the inspection result normal?

YES

>> Warning buzzer into combination meter is OK.

NO

>> Refer to 

DLK-259, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009268964

1.

CHECK METER BUZZER CIRCUIT

Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?

YES

>> GO TO 2

NO

>> Replace combination meter. Refer to 

MWI-104, "Removal and Installation"

 (type B) or 

MWI-53,

"Removal and Installation"

 (type A).

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> Inspection End.

DLK-260

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

HAZARD FUNCTION

HAZARD FUNCTION

Description

INFOID:0000000009268965

Perform answer-back for each operation with number of blinks.

Component Function Check

INFOID:0000000009268966

1.

CHECK FUNCTION

Check hazard warning lamp (“FLASHER”) in Active Test.
Is the inspection result normal?

YES

>> Hazard warning lamp circuit is OK.

NO

>> Refer to 

DLK-260, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009268967

1.

CHECK HAZARD SWITCH CIRCUIT

Operate the hazard lights by turning ON the hazard warning switch.
Is the inspection result normal?

YES

>> GO TO 2

NO

>> Repair or replace hazard warning switch circuit. Refer to 

EXL-71, "Work Flow"

.

2.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-45, "Intermittent Incident"

.

>> Inspection End.

KEYFOB ID SET UP WITH CONSULT

DLK-261

< DTC/CIRCUIT DIAGNOSIS >

[WITHOUT INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

KEYFOB ID SET UP WITH CONSULT

ID Code Entry Procedure

INFOID:0000000009268968

KEYFOB ID SET UP WITH CONSULT

NOTE:

• If a keyfob is lost, the ID code of the lost keyfob must be erased to prevent unauthorized use. A spe-

cific ID code can be erased with CONSULT. However, when the ID code of a lost keyfob is not known,

all controller ID codes should be erased. After all ID codes are erased, the ID codes of all remaining

and/or new keyfobs must be re-registered.

• When registering an additional keyfob, the existing ID codes in memory may or may not be erased. If

five ID codes are stored in memory when an additional code is registered, only the oldest code is

erased. If less than five codes are stored in memory when an additional code is registered, the new

ID code is added and no ID codes are erased.

• Entry of a maximum of five ID codes is allowed. When more than five codes are entered, the oldest ID

code will be erased.

• Even if the same ID code that is already in memory is input, the same ID code can be entered. The

code is counted as an additional code.

1. Turn ignition switch ON.
2. Select BCM.
3. Select MULTI REMOTE ENT.
4. Select WORK SUPPORT.
5. You can register, erase or confirm a keyfob ID code. To register a new code, select the following option

and follow CONSULT instructions:

• REMO CONT ID REGIST

Use this mode to register a keyfob ID code.

NOTE:

Register the ID code when keyfob or BCM is replaced, or when additional keyfob is required.

• REMO CONT ID ERASUR

Use this mode to erase a keyfob ID code.

• REMO CONT ID CONFIR

Use this mode to confirm if a keyfob ID code is registered or not.