Nissan Versa Sedan. Instruction - part 206

DLK-142

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

HOOD

INSTALLATION

Installation is in the reverse order of removal.

• Tighten hood hinge bolts to specified torque. Refer to 

DLK-140, "HOOD ASSEMBLY : Adjustment"

.

CAUTION:

• Before installing the hood hinge, apply anticorrosive agent onto the surface of the vehicle.

• After installation, perform hood assembly adjustment procedure. Refer to 

DLK-140, "HOOD ASSEM-

BLY : Adjustment"

.

• Check hood hinge rotating point for poor lubrication. If neces-

sary, apply a suitable multi-purpose grease. 

HOOD SUPPORT ROD
HOOD SUPPORT ROD : Removal and Installation

INFOID:0000000009268836

REMOVAL

1. Support hood assembly using a suitable tool.

WARNING:

Bodily injury may occur if hood assembly is not supported properly when removing hood support

rod.

2. Rotate and remove hood support rod from grommet.
3. Release tab and remove grommet from hood hinge, if necessary.

INSTALLATION

Installation is in the reverse order of removal.

JMKIA7995ZZ

RADIATOR CORE SUPPORT

DLK-143

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

RADIATOR CORE SUPPORT

Exploded View

INFOID:0000000009268837

RADIATOR CORE SUPPORT UPPER
RADIATOR CORE SUPPORT UPPER : Removal and Installation

INFOID:0000000009268838

RADIATOR CORE SUPPORT UPPER

Removal

1. Remove ground harness bolt (A).

2. Remove horn. Refer to 

HRN-6, "Removal and Installation"

.

3. Remove hood lock assembly and hood lock control cable assembly clip. Refer to 

DLK-164, "HOOD LOCK

: Removal and Installation"

.

1.

Radiator upper seal

2.

Condenser side seal

3.

Radiator side seal (RH)

4.

Radiator side seal (LH)

5.

Radiator core support lower

6.

Radiator core support upper

JMKIA8149ZZ

JMKIA8026ZZ

DLK-144

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

RADIATOR CORE SUPPORT

4. Remove crash zone sensor. Refer to 

SR-22, "Removal and Installation"

.

5. Remove radiator cap adapter bracket bolt (A) and radiator reser-

voir tank bolt (B).

6. Remove radiator upper seal clips.
7. Remove upper clips of radiator side seal (LH/RH).
8. Disconnect all harness clips.
9. Remove front bumper fascia upper side clips (A).

10. Remove radiator core support upper bolts.
11. Pull back on upper part of front bumper fascia (1) and then

remove radiator core support upper (2) by pulling upward.

Installation

Installation is in the reverse order of removal.

RADIATOR CORE SUPPORT LOWER
RADIATOR CORE SUPPORT LOWER : Removal and Installation

INFOID:0000000009268839

RADIATOR CORE SUPPORT LOWER

Removal

1. Remove under cover. Refer to 

EXT-19, "Removal and Installation"

.

2. Remove radiator upper seal clips.

JMKIA8027ZZ

JMKIA8028ZZ

JMKIA8029ZZ

RADIATOR CORE SUPPORT

DLK-145

< REMOVAL AND INSTALLATION >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3. Remove front bumper fascia upper side clips (A).

4. Remove fender protector (LH/RH) clips from radiator core support lower. Refer to 

EXT-26, "Removal and

Installation"

.

5. Remove lower clips of radiator side seal (LH/RH).
6. Remove lower clips of condenser side seal.
7. Use suitable tools (A) to suspend components and to prevent

them from falling.

CAUTION:

Use care to avoid damage to radiator and condenser.

8. Remove radiator core support lower bolts and radiator core support lower.

Installation

Installation is in the reverse order of removal.

JMKIA8028ZZ

JMKIA8030ZZ