Nissan Versa Sedan. Instruction - part 10

AV-32

< REMOVAL AND INSTALLATION >

[BASE AUDIO]

ANTENNA FEEDER

ANTENNA FEEDER

Feeder Layout

INFOID:0000000009266714

AWNIA2457ZZ

1.

Antenna mast

2.

Antenna feed

3.

Clip

4.

Harness connector

5.

Audio unit

6.

Harness connector

AV

PRECAUTIONS

AV-33

< PRECAUTION >

[MID AUDIO]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

PRECAUTION

PRECAUTIONS

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT 
PRE-TENSIONER"

INFOID:0000000009266715

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along

with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain

types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS

system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front

air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.

Information necessary to service the system safely is included in the SR and SB section of this Service Man-

ual.

WARNING:

• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in

the event of a collision which would result in air bag inflation, all maintenance must be performed by

an authorized NISSAN/INFINITI dealer.

• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal

injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag

Module, see the SR section.

• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this

Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-

ness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

WARNING:

• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-

tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a

hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing

serious injury.

• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the

battery, and wait at least 3 minutes before performing any service.

Precaution for Work

INFOID:0000000009266716

• When removing or disassembling each component, be careful not to damage or deform it. If a component

may be subject to interference, be sure to protect it with a shop cloth.

• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component

with a shop cloth or vinyl tape to protect it.

• Protect the removed parts with a shop cloth and prevent them from being dropped.

• Replace a deformed or damaged clip.

• If a part is specified as a non-reusable part, always replace it with a new one.

• Be sure to tighten bolts and nuts securely to the specified torque.

• After installation is complete, be sure to check that each part works properly.

• Follow the steps below to clean components:

- Water soluble dirt:

• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.

• Then rub with a soft, dry cloth.

- Oily  dirt:

• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty

area.

• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.

• Then rub with a soft, dry cloth.

- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.

- For genuine leather seats, use a genuine leather seat cleaner.

AV-34

< PREPARATION >

[MID AUDIO]

PREPARATION

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000009266717

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000009266718

Tool number
(Kent-Moore No.)
Tool name

Description

—

(J-46534)
Trim Tool Set

Removing trim components

AWJIA0483ZZ

Tool name

Description

Power tool

Loosening nuts, screws and bolts

PIIB1407E

AV

COMPONENT PARTS

AV-35

< SYSTEM DESCRIPTION >

[MID AUDIO]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYSTEM DESCRIPTION

COMPONENT PARTS

Component Parts Location

INFOID:0000000009375100

Component Description

INFOID:0000000009375101

1.

Rod antenna

2.

Antenna base (antenna amp.)

3.

Rear door speaker RH

4.

Front door speaker RH

5.

Front door speaker LH

6.

Rear door speaker LH

7.

Microphone

8.

Steering wheel audio control switches 9.

Audio unit

10. Bluetooth

®

 control unit (view with lug-

gage side lower finisher RH removed)

11. Bluetooth

®

 antenna (view with lug-

gage side lower finisher RH removed)

AWNIA3041ZZ

Part name

Description

Audio unit

• Controls audio system functions
• Inputs amplified AM/FM radio signal from antenna amp.
• Inputs vehicle speed signal from combination meter
• Inputs hands-free phone functions from Bluetooth

®

 control unit

• Outputs sound signals to front and rear door speakers

Front door speakers

• Outputs sound signal from audio unit
• Outputs high, mid and low-range sounds

Rear door speakers

Bluetooth

®

 control unit

• Controls hands-free phone and audio system functions
• Inputs steering switch signal
• Inputs microphone voice signal
• Outputs steering switch signal to audio unit
• Outputs hands-free phone functions to audio unit